Initial commit from HTC m7ul-3.4.10-jb-crc-ddcfb8c
diff --git a/include/linux/i2c/adp5588.h b/include/linux/i2c/adp5588.h
new file mode 100644
index 0000000..cec17cf
--- /dev/null
+++ b/include/linux/i2c/adp5588.h
@@ -0,0 +1,171 @@
+/*
+ * Analog Devices ADP5588 I/O Expander and QWERTY Keypad Controller
+ *
+ * Copyright 2009-2010 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef _ADP5588_H
+#define _ADP5588_H
+
+#define DEV_ID 0x00 /* Device ID */
+#define CFG 0x01 /* Configuration Register1 */
+#define INT_STAT 0x02 /* Interrupt Status Register */
+#define KEY_LCK_EC_STAT 0x03 /* Key Lock and Event Counter Register */
+#define Key_EVENTA 0x04 /* Key Event Register A */
+#define Key_EVENTB 0x05 /* Key Event Register B */
+#define Key_EVENTC 0x06 /* Key Event Register C */
+#define Key_EVENTD 0x07 /* Key Event Register D */
+#define Key_EVENTE 0x08 /* Key Event Register E */
+#define Key_EVENTF 0x09 /* Key Event Register F */
+#define Key_EVENTG 0x0A /* Key Event Register G */
+#define Key_EVENTH 0x0B /* Key Event Register H */
+#define Key_EVENTI 0x0C /* Key Event Register I */
+#define Key_EVENTJ 0x0D /* Key Event Register J */
+#define KP_LCK_TMR 0x0E /* Keypad Lock1 to Lock2 Timer */
+#define UNLOCK1 0x0F /* Unlock Key1 */
+#define UNLOCK2 0x10 /* Unlock Key2 */
+#define GPIO_INT_STAT1 0x11 /* GPIO Interrupt Status */
+#define GPIO_INT_STAT2 0x12 /* GPIO Interrupt Status */
+#define GPIO_INT_STAT3 0x13 /* GPIO Interrupt Status */
+#define GPIO_DAT_STAT1 0x14 /* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_STAT2 0x15 /* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_STAT3 0x16 /* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_OUT1 0x17 /* GPIO DATA OUT */
+#define GPIO_DAT_OUT2 0x18 /* GPIO DATA OUT */
+#define GPIO_DAT_OUT3 0x19 /* GPIO DATA OUT */
+#define GPIO_INT_EN1 0x1A /* GPIO Interrupt Enable */
+#define GPIO_INT_EN2 0x1B /* GPIO Interrupt Enable */
+#define GPIO_INT_EN3 0x1C /* GPIO Interrupt Enable */
+#define KP_GPIO1 0x1D /* Keypad or GPIO Selection */
+#define KP_GPIO2 0x1E /* Keypad or GPIO Selection */
+#define KP_GPIO3 0x1F /* Keypad or GPIO Selection */
+#define GPI_EM1 0x20 /* GPI Event Mode 1 */
+#define GPI_EM2 0x21 /* GPI Event Mode 2 */
+#define GPI_EM3 0x22 /* GPI Event Mode 3 */
+#define GPIO_DIR1 0x23 /* GPIO Data Direction */
+#define GPIO_DIR2 0x24 /* GPIO Data Direction */
+#define GPIO_DIR3 0x25 /* GPIO Data Direction */
+#define GPIO_INT_LVL1 0x26 /* GPIO Edge/Level Detect */
+#define GPIO_INT_LVL2 0x27 /* GPIO Edge/Level Detect */
+#define GPIO_INT_LVL3 0x28 /* GPIO Edge/Level Detect */
+#define Debounce_DIS1 0x29 /* Debounce Disable */
+#define Debounce_DIS2 0x2A /* Debounce Disable */
+#define Debounce_DIS3 0x2B /* Debounce Disable */
+#define GPIO_PULL1 0x2C /* GPIO Pull Disable */
+#define GPIO_PULL2 0x2D /* GPIO Pull Disable */
+#define GPIO_PULL3 0x2E /* GPIO Pull Disable */
+#define CMP_CFG_STAT 0x30 /* Comparator Configuration and Status Register */
+#define CMP_CONFG_SENS1 0x31 /* Sensor1 Comparator Configuration Register */
+#define CMP_CONFG_SENS2 0x32 /* L2 Light Sensor Reference Level, Output Falling for Sensor 1 */
+#define CMP1_LVL2_TRIP 0x33 /* L2 Light Sensor Hysteresis (Active when Output Rising) for Sensor 1 */
+#define CMP1_LVL2_HYS 0x34 /* L3 Light Sensor Reference Level, Output Falling For Sensor 1 */
+#define CMP1_LVL3_TRIP 0x35 /* L3 Light Sensor Hysteresis (Active when Output Rising) For Sensor 1 */
+#define CMP1_LVL3_HYS 0x36 /* Sensor 2 Comparator Configuration Register */
+#define CMP2_LVL2_TRIP 0x37 /* L2 Light Sensor Reference Level, Output Falling for Sensor 2 */
+#define CMP2_LVL2_HYS 0x38 /* L2 Light Sensor Hysteresis (Active when Output Rising) for Sensor 2 */
+#define CMP2_LVL3_TRIP 0x39 /* L3 Light Sensor Reference Level, Output Falling For Sensor 2 */
+#define CMP2_LVL3_HYS 0x3A /* L3 Light Sensor Hysteresis (Active when Output Rising) For Sensor 2 */
+#define CMP1_ADC_DAT_R1 0x3B /* Comparator 1 ADC data Register1 */
+#define CMP1_ADC_DAT_R2 0x3C /* Comparator 1 ADC data Register2 */
+#define CMP2_ADC_DAT_R1 0x3D /* Comparator 2 ADC data Register1 */
+#define CMP2_ADC_DAT_R2 0x3E /* Comparator 2 ADC data Register2 */
+
+#define ADP5588_DEVICE_ID_MASK 0xF
+
+ /* Configuration Register1 */
+#define ADP5588_AUTO_INC (1 << 7)
+#define ADP5588_GPIEM_CFG (1 << 6)
+#define ADP5588_OVR_FLOW_M (1 << 5)
+#define ADP5588_INT_CFG (1 << 4)
+#define ADP5588_OVR_FLOW_IEN (1 << 3)
+#define ADP5588_K_LCK_IM (1 << 2)
+#define ADP5588_GPI_IEN (1 << 1)
+#define ADP5588_KE_IEN (1 << 0)
+
+/* Interrupt Status Register */
+#define ADP5588_CMP2_INT (1 << 5)
+#define ADP5588_CMP1_INT (1 << 4)
+#define ADP5588_OVR_FLOW_INT (1 << 3)
+#define ADP5588_K_LCK_INT (1 << 2)
+#define ADP5588_GPI_INT (1 << 1)
+#define ADP5588_KE_INT (1 << 0)
+
+/* Key Lock and Event Counter Register */
+#define ADP5588_K_LCK_EN (1 << 6)
+#define ADP5588_LCK21 0x30
+#define ADP5588_KEC 0xF
+
+#define ADP5588_MAXGPIO 18
+#define ADP5588_BANK(offs) ((offs) >> 3)
+#define ADP5588_BIT(offs) (1u << ((offs) & 0x7))
+
+/* Put one of these structures in i2c_board_info platform_data */
+
+#define ADP5588_KEYMAPSIZE 80
+
+#define GPI_PIN_ROW0 97
+#define GPI_PIN_ROW1 98
+#define GPI_PIN_ROW2 99
+#define GPI_PIN_ROW3 100
+#define GPI_PIN_ROW4 101
+#define GPI_PIN_ROW5 102
+#define GPI_PIN_ROW6 103
+#define GPI_PIN_ROW7 104
+#define GPI_PIN_COL0 105
+#define GPI_PIN_COL1 106
+#define GPI_PIN_COL2 107
+#define GPI_PIN_COL3 108
+#define GPI_PIN_COL4 109
+#define GPI_PIN_COL5 110
+#define GPI_PIN_COL6 111
+#define GPI_PIN_COL7 112
+#define GPI_PIN_COL8 113
+#define GPI_PIN_COL9 114
+
+#define GPI_PIN_ROW_BASE GPI_PIN_ROW0
+#define GPI_PIN_ROW_END GPI_PIN_ROW7
+#define GPI_PIN_COL_BASE GPI_PIN_COL0
+#define GPI_PIN_COL_END GPI_PIN_COL9
+
+#define GPI_PIN_BASE GPI_PIN_ROW_BASE
+#define GPI_PIN_END GPI_PIN_COL_END
+
+#define ADP5588_GPIMAPSIZE_MAX (GPI_PIN_END - GPI_PIN_BASE + 1)
+
+struct adp5588_gpi_map {
+ unsigned short pin;
+ unsigned short sw_evt;
+};
+
+struct adp5588_kpad_platform_data {
+ int rows; /* Number of rows */
+ int cols; /* Number of columns */
+ const unsigned short *keymap; /* Pointer to keymap */
+ unsigned short keymapsize; /* Keymap size */
+ unsigned repeat:1; /* Enable key repeat */
+ unsigned en_keylock:1; /* Enable Key Lock feature */
+ unsigned short unlock_key1; /* Unlock Key 1 */
+ unsigned short unlock_key2; /* Unlock Key 2 */
+ const struct adp5588_gpi_map *gpimap;
+ unsigned short gpimapsize;
+ const struct adp5588_gpio_platform_data *gpio_data;
+};
+
+struct i2c_client; /* forward declaration */
+
+struct adp5588_gpio_platform_data {
+ int gpio_start; /* GPIO Chip base # */
+ unsigned irq_base; /* interrupt base # */
+ unsigned pullup_dis_mask; /* Pull-Up Disable Mask */
+ int (*setup)(struct i2c_client *client,
+ int gpio, unsigned ngpio,
+ void *context);
+ int (*teardown)(struct i2c_client *client,
+ int gpio, unsigned ngpio,
+ void *context);
+ void *context;
+};
+
+#endif
diff --git a/include/linux/i2c/adp8860.h b/include/linux/i2c/adp8860.h
new file mode 100644
index 0000000..0b4d398
--- /dev/null
+++ b/include/linux/i2c/adp8860.h
@@ -0,0 +1,154 @@
+/*
+ * Definitions and platform data for Analog Devices
+ * Backlight drivers ADP8860
+ *
+ * Copyright 2009-2010 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __LINUX_I2C_ADP8860_H
+#define __LINUX_I2C_ADP8860_H
+
+#include <linux/leds.h>
+#include <linux/types.h>
+
+#define ID_ADP8860 8860
+
+#define ADP8860_MAX_BRIGHTNESS 0x7F
+#define FLAG_OFFT_SHIFT 8
+
+/*
+ * LEDs subdevice platform data
+ */
+
+#define ADP8860_LED_DIS_BLINK (0 << FLAG_OFFT_SHIFT)
+#define ADP8860_LED_OFFT_600ms (1 << FLAG_OFFT_SHIFT)
+#define ADP8860_LED_OFFT_1200ms (2 << FLAG_OFFT_SHIFT)
+#define ADP8860_LED_OFFT_1800ms (3 << FLAG_OFFT_SHIFT)
+
+#define ADP8860_LED_ONT_200ms 0
+#define ADP8860_LED_ONT_600ms 1
+#define ADP8860_LED_ONT_800ms 2
+#define ADP8860_LED_ONT_1200ms 3
+
+#define ADP8860_LED_D7 (7)
+#define ADP8860_LED_D6 (6)
+#define ADP8860_LED_D5 (5)
+#define ADP8860_LED_D4 (4)
+#define ADP8860_LED_D3 (3)
+#define ADP8860_LED_D2 (2)
+#define ADP8860_LED_D1 (1)
+
+/*
+ * Backlight subdevice platform data
+ */
+
+#define ADP8860_BL_D7 (1 << 6)
+#define ADP8860_BL_D6 (1 << 5)
+#define ADP8860_BL_D5 (1 << 4)
+#define ADP8860_BL_D4 (1 << 3)
+#define ADP8860_BL_D3 (1 << 2)
+#define ADP8860_BL_D2 (1 << 1)
+#define ADP8860_BL_D1 (1 << 0)
+
+#define ADP8860_FADE_T_DIS 0 /* Fade Timer Disabled */
+#define ADP8860_FADE_T_300ms 1 /* 0.3 Sec */
+#define ADP8860_FADE_T_600ms 2
+#define ADP8860_FADE_T_900ms 3
+#define ADP8860_FADE_T_1200ms 4
+#define ADP8860_FADE_T_1500ms 5
+#define ADP8860_FADE_T_1800ms 6
+#define ADP8860_FADE_T_2100ms 7
+#define ADP8860_FADE_T_2400ms 8
+#define ADP8860_FADE_T_2700ms 9
+#define ADP8860_FADE_T_3000ms 10
+#define ADP8860_FADE_T_3500ms 11
+#define ADP8860_FADE_T_4000ms 12
+#define ADP8860_FADE_T_4500ms 13
+#define ADP8860_FADE_T_5000ms 14
+#define ADP8860_FADE_T_5500ms 15 /* 5.5 Sec */
+
+#define ADP8860_FADE_LAW_LINEAR 0
+#define ADP8860_FADE_LAW_SQUARE 1
+#define ADP8860_FADE_LAW_CUBIC1 2
+#define ADP8860_FADE_LAW_CUBIC2 3
+
+#define ADP8860_BL_AMBL_FILT_80ms 0 /* Light sensor filter time */
+#define ADP8860_BL_AMBL_FILT_160ms 1
+#define ADP8860_BL_AMBL_FILT_320ms 2
+#define ADP8860_BL_AMBL_FILT_640ms 3
+#define ADP8860_BL_AMBL_FILT_1280ms 4
+#define ADP8860_BL_AMBL_FILT_2560ms 5
+#define ADP8860_BL_AMBL_FILT_5120ms 6
+#define ADP8860_BL_AMBL_FILT_10240ms 7 /* 10.24 sec */
+
+/*
+ * Blacklight current 0..30mA
+ */
+#define ADP8860_BL_CUR_mA(I) ((I * 127) / 30)
+
+/*
+ * L2 comparator current 0..1106uA
+ */
+#define ADP8860_L2_COMP_CURR_uA(I) ((I * 255) / 1106)
+
+/*
+ * L3 comparator current 0..138uA
+ */
+#define ADP8860_L3_COMP_CURR_uA(I) ((I * 255) / 138)
+
+struct adp8860_backlight_platform_data {
+ u8 bl_led_assign; /* 1 = Backlight 0 = Individual LED */
+
+ u8 bl_fade_in; /* Backlight Fade-In Timer */
+ u8 bl_fade_out; /* Backlight Fade-Out Timer */
+ u8 bl_fade_law; /* fade-on/fade-off transfer characteristic */
+
+ u8 en_ambl_sens; /* 1 = enable ambient light sensor */
+ u8 abml_filt; /* Light sensor filter time */
+
+ u8 l1_daylight_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l1_daylight_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l2_office_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l2_office_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l3_dark_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l3_dark_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+
+ u8 l2_trip; /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
+ u8 l2_hyst; /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
+ u8 l3_trip; /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
+ u8 l3_hyst; /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
+
+ /**
+ * Independent Current Sinks / LEDS
+ * Sinks not assigned to the Backlight can be exposed to
+ * user space using the LEDS CLASS interface
+ */
+
+ int num_leds;
+ struct led_info *leds;
+ u8 led_fade_in; /* LED Fade-In Timer */
+ u8 led_fade_out; /* LED Fade-Out Timer */
+ u8 led_fade_law; /* fade-on/fade-off transfer characteristic */
+ u8 led_on_time;
+
+ /**
+ * Gain down disable. Setting this option does not allow the
+ * charge pump to switch to lower gains. NOT AVAILABLE on ADP8860
+ * 1 = the charge pump doesn't switch down in gain until all LEDs are 0.
+ * The charge pump switches up in gain as needed. This feature is
+ * useful if the ADP8863 charge pump is used to drive an external load.
+ * This feature must be used when utilizing small fly capacitors
+ * (0402 or smaller).
+ * 0 = the charge pump automatically switches up and down in gain.
+ * This provides optimal efficiency, but is not suitable for driving
+ * loads that are not connected through the ADP8863 diode drivers.
+ * Additionally, the charge pump fly capacitors should be low ESR
+ * and sized 0603 or greater.
+ */
+
+ u8 gdwn_dis;
+};
+
+#endif /* __LINUX_I2C_ADP8860_H */
diff --git a/include/linux/i2c/adp8870.h b/include/linux/i2c/adp8870.h
new file mode 100644
index 0000000..624dcec
--- /dev/null
+++ b/include/linux/i2c/adp8870.h
@@ -0,0 +1,153 @@
+/*
+ * Definitions and platform data for Analog Devices
+ * Backlight drivers ADP8870
+ *
+ * Copyright 2009-2010 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __LINUX_I2C_ADP8870_H
+#define __LINUX_I2C_ADP8870_H
+
+#define ID_ADP8870 8870
+
+#define ADP8870_MAX_BRIGHTNESS 0x7F
+#define FLAG_OFFT_SHIFT 8
+
+/*
+ * LEDs subdevice platform data
+ */
+
+#define ADP8870_LED_DIS_BLINK (0 << FLAG_OFFT_SHIFT)
+#define ADP8870_LED_OFFT_600ms (1 << FLAG_OFFT_SHIFT)
+#define ADP8870_LED_OFFT_1200ms (2 << FLAG_OFFT_SHIFT)
+#define ADP8870_LED_OFFT_1800ms (3 << FLAG_OFFT_SHIFT)
+
+#define ADP8870_LED_ONT_200ms 0
+#define ADP8870_LED_ONT_600ms 1
+#define ADP8870_LED_ONT_800ms 2
+#define ADP8870_LED_ONT_1200ms 3
+
+#define ADP8870_LED_D7 (7)
+#define ADP8870_LED_D6 (6)
+#define ADP8870_LED_D5 (5)
+#define ADP8870_LED_D4 (4)
+#define ADP8870_LED_D3 (3)
+#define ADP8870_LED_D2 (2)
+#define ADP8870_LED_D1 (1)
+
+/*
+ * Backlight subdevice platform data
+ */
+
+#define ADP8870_BL_D7 (1 << 6)
+#define ADP8870_BL_D6 (1 << 5)
+#define ADP8870_BL_D5 (1 << 4)
+#define ADP8870_BL_D4 (1 << 3)
+#define ADP8870_BL_D3 (1 << 2)
+#define ADP8870_BL_D2 (1 << 1)
+#define ADP8870_BL_D1 (1 << 0)
+
+#define ADP8870_FADE_T_DIS 0 /* Fade Timer Disabled */
+#define ADP8870_FADE_T_300ms 1 /* 0.3 Sec */
+#define ADP8870_FADE_T_600ms 2
+#define ADP8870_FADE_T_900ms 3
+#define ADP8870_FADE_T_1200ms 4
+#define ADP8870_FADE_T_1500ms 5
+#define ADP8870_FADE_T_1800ms 6
+#define ADP8870_FADE_T_2100ms 7
+#define ADP8870_FADE_T_2400ms 8
+#define ADP8870_FADE_T_2700ms 9
+#define ADP8870_FADE_T_3000ms 10
+#define ADP8870_FADE_T_3500ms 11
+#define ADP8870_FADE_T_4000ms 12
+#define ADP8870_FADE_T_4500ms 13
+#define ADP8870_FADE_T_5000ms 14
+#define ADP8870_FADE_T_5500ms 15 /* 5.5 Sec */
+
+#define ADP8870_FADE_LAW_LINEAR 0
+#define ADP8870_FADE_LAW_SQUARE 1
+#define ADP8870_FADE_LAW_CUBIC1 2
+#define ADP8870_FADE_LAW_CUBIC2 3
+
+#define ADP8870_BL_AMBL_FILT_80ms 0 /* Light sensor filter time */
+#define ADP8870_BL_AMBL_FILT_160ms 1
+#define ADP8870_BL_AMBL_FILT_320ms 2
+#define ADP8870_BL_AMBL_FILT_640ms 3
+#define ADP8870_BL_AMBL_FILT_1280ms 4
+#define ADP8870_BL_AMBL_FILT_2560ms 5
+#define ADP8870_BL_AMBL_FILT_5120ms 6
+#define ADP8870_BL_AMBL_FILT_10240ms 7 /* 10.24 sec */
+
+/*
+ * Blacklight current 0..30mA
+ */
+#define ADP8870_BL_CUR_mA(I) ((I * 127) / 30)
+
+/*
+ * L2 comparator current 0..1106uA
+ */
+#define ADP8870_L2_COMP_CURR_uA(I) ((I * 255) / 1106)
+
+/*
+ * L3 comparator current 0..551uA
+ */
+#define ADP8870_L3_COMP_CURR_uA(I) ((I * 255) / 551)
+
+/*
+ * L4 comparator current 0..275uA
+ */
+#define ADP8870_L4_COMP_CURR_uA(I) ((I * 255) / 275)
+
+/*
+ * L5 comparator current 0..138uA
+ */
+#define ADP8870_L5_COMP_CURR_uA(I) ((I * 255) / 138)
+
+struct adp8870_backlight_platform_data {
+ u8 bl_led_assign; /* 1 = Backlight 0 = Individual LED */
+ u8 pwm_assign; /* 1 = Enables PWM mode */
+
+ u8 bl_fade_in; /* Backlight Fade-In Timer */
+ u8 bl_fade_out; /* Backlight Fade-Out Timer */
+ u8 bl_fade_law; /* fade-on/fade-off transfer characteristic */
+
+ u8 en_ambl_sens; /* 1 = enable ambient light sensor */
+ u8 abml_filt; /* Light sensor filter time */
+
+ u8 l1_daylight_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l1_daylight_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l2_bright_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l2_bright_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l3_office_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l3_office_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l4_indoor_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l4_indor_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l5_dark_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l5_dark_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+
+ u8 l2_trip; /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
+ u8 l2_hyst; /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
+ u8 l3_trip; /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
+ u8 l3_hyst; /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
+ u8 l4_trip; /* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */
+ u8 l4_hyst; /* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */
+ u8 l5_trip; /* use L5_COMP_CURR_uA(I) 0 <= I <= 138 uA */
+ u8 l5_hyst; /* use L6_COMP_CURR_uA(I) 0 <= I <= 138 uA */
+
+ /**
+ * Independent Current Sinks / LEDS
+ * Sinks not assigned to the Backlight can be exposed to
+ * user space using the LEDS CLASS interface
+ */
+
+ int num_leds;
+ struct led_info *leds;
+ u8 led_fade_in; /* LED Fade-In Timer */
+ u8 led_fade_out; /* LED Fade-Out Timer */
+ u8 led_fade_law; /* fade-on/fade-off transfer characteristic */
+ u8 led_on_time;
+};
+
+#endif /* __LINUX_I2C_ADP8870_H */
diff --git a/include/linux/i2c/ads1015.h b/include/linux/i2c/ads1015.h
new file mode 100644
index 0000000..d5aa2a0
--- /dev/null
+++ b/include/linux/i2c/ads1015.h
@@ -0,0 +1,36 @@
+/*
+ * Platform Data for ADS1015 12-bit 4-input ADC
+ * (C) Copyright 2010
+ * Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef LINUX_ADS1015_H
+#define LINUX_ADS1015_H
+
+#define ADS1015_CHANNELS 8
+
+struct ads1015_channel_data {
+ bool enabled;
+ unsigned int pga;
+ unsigned int data_rate;
+};
+
+struct ads1015_platform_data {
+ struct ads1015_channel_data channel_data[ADS1015_CHANNELS];
+};
+
+#endif /* LINUX_ADS1015_H */
diff --git a/include/linux/i2c/apds990x.h b/include/linux/i2c/apds990x.h
new file mode 100644
index 0000000..d186fcc
--- /dev/null
+++ b/include/linux/i2c/apds990x.h
@@ -0,0 +1,79 @@
+/*
+ * This file is part of the APDS990x sensor driver.
+ * Chip is combined proximity and ambient light sensor.
+ *
+ * Copyright (C) 2010 Nokia Corporation and/or its subsidiary(-ies).
+ *
+ * Contact: Samu Onkalo <samu.p.onkalo@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __APDS990X_H__
+#define __APDS990X_H__
+
+
+#define APDS_IRLED_CURR_12mA 0x3
+#define APDS_IRLED_CURR_25mA 0x2
+#define APDS_IRLED_CURR_50mA 0x1
+#define APDS_IRLED_CURR_100mA 0x0
+
+/**
+ * struct apds990x_chip_factors - defines effect of the cover window
+ * @ga: Total glass attenuation
+ * @cf1: clear channel factor 1 for raw to lux conversion
+ * @irf1: IR channel factor 1 for raw to lux conversion
+ * @cf2: clear channel factor 2 for raw to lux conversion
+ * @irf2: IR channel factor 2 for raw to lux conversion
+ * @df: device factor for conversion formulas
+ *
+ * Structure for tuning ALS calculation to match with environment.
+ * Values depend on the material above the sensor and the sensor
+ * itself. If the GA is zero, driver will use uncovered sensor default values
+ * format: decimal value * APDS_PARAM_SCALE except df which is plain integer.
+ */
+#define APDS_PARAM_SCALE 4096
+struct apds990x_chip_factors {
+ int ga;
+ int cf1;
+ int irf1;
+ int cf2;
+ int irf2;
+ int df;
+};
+
+/**
+ * struct apds990x_platform_data - platform data for apsd990x.c driver
+ * @cf: chip factor data
+ * @pddrive: IR-led driving current
+ * @ppcount: number of IR pulses used for proximity estimation
+ * @setup_resources: interrupt line setup call back function
+ * @release_resources: interrupt line release call back function
+ *
+ * Proximity detection result depends heavily on correct ppcount, pdrive
+ * and cover window.
+ *
+ */
+
+struct apds990x_platform_data {
+ struct apds990x_chip_factors cf;
+ u8 pdrive;
+ u8 ppcount;
+ int (*setup_resources)(void);
+ int (*release_resources)(void);
+};
+
+#endif
diff --git a/include/linux/i2c/at24.h b/include/linux/i2c/at24.h
new file mode 100644
index 0000000..285025a
--- /dev/null
+++ b/include/linux/i2c/at24.h
@@ -0,0 +1,55 @@
+/*
+ * at24.h - platform_data for the at24 (generic eeprom) driver
+ * (C) Copyright 2008 by Pengutronix
+ * (C) Copyright 2012 by Wolfram Sang
+ * same license as the driver
+ */
+
+#ifndef _LINUX_AT24_H
+#define _LINUX_AT24_H
+
+#include <linux/types.h>
+#include <linux/memory.h>
+
+/**
+ * struct at24_platform_data - data to set up at24 (generic eeprom) driver
+ * @byte_len: size of eeprom in byte
+ * @page_size: number of byte which can be written in one go
+ * @flags: tunable options, check AT24_FLAG_* defines
+ * @setup: an optional callback invoked after eeprom is probed; enables kernel
+ code to access eeprom via memory_accessor, see example
+ * @context: optional parameter passed to setup()
+ *
+ * If you set up a custom eeprom type, please double-check the parameters.
+ * Especially page_size needs extra care, as you risk data loss if your value
+ * is bigger than what the chip actually supports!
+ *
+ * An example in pseudo code for a setup() callback:
+ *
+ * void get_mac_addr(struct memory_accessor *mem_acc, void *context)
+ * {
+ * u8 *mac_addr = ethernet_pdata->mac_addr;
+ * off_t offset = context;
+ *
+ * // Read MAC addr from EEPROM
+ * if (mem_acc->read(mem_acc, mac_addr, offset, ETH_ALEN) == ETH_ALEN)
+ * pr_info("Read MAC addr from EEPROM: %pM\n", mac_addr);
+ * }
+ *
+ * This function pointer and context can now be set up in at24_platform_data.
+ */
+
+struct at24_platform_data {
+ u32 byte_len; /* size (sum of all addr) */
+ u16 page_size; /* for writes */
+ u8 flags;
+#define AT24_FLAG_ADDR16 0x80 /* address pointer is 16 bit */
+#define AT24_FLAG_READONLY 0x40 /* sysfs-entry will be read-only */
+#define AT24_FLAG_IRUGO 0x20 /* sysfs-entry will be world-readable */
+#define AT24_FLAG_TAKE8ADDR 0x10 /* take always 8 addresses (24c00) */
+
+ void (*setup)(struct memory_accessor *, void *context);
+ void *context;
+};
+
+#endif /* _LINUX_AT24_H */
diff --git a/include/linux/i2c/atmel_mxt_ts.h b/include/linux/i2c/atmel_mxt_ts.h
new file mode 100644
index 0000000..4f61be6
--- /dev/null
+++ b/include/linux/i2c/atmel_mxt_ts.h
@@ -0,0 +1,75 @@
+/*
+ * Atmel maXTouch Touchscreen driver
+ *
+ * Copyright (C) 2010 Samsung Electronics Co.Ltd
+ * Author: Joonyoung Shim <jy0922.shim@samsung.com>
+ * Copyright (c) 2011-2012, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __LINUX_ATMEL_MXT_TS_H
+#define __LINUX_ATMEL_MXT_TS_H
+
+#include <linux/types.h>
+
+#define MXT_NORMAL 0x0
+#define MXT_DIAGONAL 0x1
+#define MXT_HORIZONTAL_FLIP 0x2
+#define MXT_ROTATED_90_COUNTER 0x3
+#define MXT_VERTICAL_FLIP 0x4
+#define MXT_ROTATED_90 0x5
+#define MXT_ROTATED_180 0x6
+#define MXT_DIAGONAL_COUNTER 0x7
+
+#define MXT_KEYARRAY_MAX_KEYS 32
+
+#define MXT_BOOTLOADER_ID_224 0x0A
+#define MXT_BOOTLOADER_ID_224E 0x06
+#define MXT_BOOTLOADER_ID_1386 0x01
+#define MXT_BOOTLOADER_ID_1386E 0x10
+
+struct mxt_config_info {
+ const u8 *config;
+ size_t config_length;
+ u8 family_id;
+ u8 variant_id;
+ u8 version;
+ u8 build;
+ u8 bootldr_id;
+
+ const char *fw_name;
+};
+
+struct mxt_platform_data {
+ const struct mxt_config_info *config_array;
+ size_t config_array_size;
+
+
+ u32 panel_minx;
+ u32 panel_maxx;
+ u32 panel_miny;
+ u32 panel_maxy;
+
+
+ u32 disp_minx;
+ u32 disp_maxx;
+ u32 disp_miny;
+ u32 disp_maxy;
+
+ unsigned long irqflags;
+ bool i2c_pull_up;
+ bool digital_pwr_regulator;
+ int reset_gpio;
+ int irq_gpio;
+ int *key_codes;
+
+ u8(*read_chg) (void);
+ int (*init_hw) (bool);
+ int (*power_on) (bool);
+};
+
+#endif
diff --git a/include/linux/i2c/bh1770glc.h b/include/linux/i2c/bh1770glc.h
new file mode 100644
index 0000000..8b5e2df
--- /dev/null
+++ b/include/linux/i2c/bh1770glc.h
@@ -0,0 +1,53 @@
+/*
+ * This file is part of the ROHM BH1770GLC / OSRAM SFH7770 sensor driver.
+ * Chip is combined proximity and ambient light sensor.
+ *
+ * Copyright (C) 2010 Nokia Corporation and/or its subsidiary(-ies).
+ *
+ * Contact: Samu Onkalo <samu.p.onkalo@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __BH1770_H__
+#define __BH1770_H__
+
+/**
+ * struct bh1770_platform_data - platform data for bh1770glc driver
+ * @led_def_curr: IR led driving current.
+ * @glass_attenuation: Attenuation factor for covering window.
+ * @setup_resources: Call back for interrupt line setup function
+ * @release_resources: Call back for interrupte line release function
+ *
+ * Example of glass attenuation: 16384 * 385 / 100 means attenuation factor
+ * of 3.85. i.e. light_above_sensor = light_above_cover_window / 3.85
+ */
+
+struct bh1770_platform_data {
+#define BH1770_LED_5mA 0
+#define BH1770_LED_10mA 1
+#define BH1770_LED_20mA 2
+#define BH1770_LED_50mA 3
+#define BH1770_LED_100mA 4
+#define BH1770_LED_150mA 5
+#define BH1770_LED_200mA 6
+ __u8 led_def_curr;
+#define BH1770_NEUTRAL_GA 16384 /* 16384 / 16384 = 1 */
+ __u32 glass_attenuation;
+ int (*setup_resources)(void);
+ int (*release_resources)(void);
+};
+#endif
diff --git a/include/linux/i2c/dm355evm_msp.h b/include/linux/i2c/dm355evm_msp.h
new file mode 100644
index 0000000..3724703
--- /dev/null
+++ b/include/linux/i2c/dm355evm_msp.h
@@ -0,0 +1,79 @@
+/*
+ * dm355evm_msp.h - support MSP430 microcontroller on DM355EVM board
+ */
+#ifndef __LINUX_I2C_DM355EVM_MSP
+#define __LINUX_I2C_DM355EVM_MSP
+
+/*
+ * Written against Spectrum's writeup for the A4 firmware revision,
+ * and tweaked to match source and rev D2 schematics by removing CPLD
+ * and NOR flash hooks (which were last appropriate in rev B boards).
+ *
+ * Note that the firmware supports a flavor of write posting ... to be
+ * sure a write completes, issue another read or write.
+ */
+
+/* utilities to access "registers" emulated by msp430 firmware */
+extern int dm355evm_msp_write(u8 value, u8 reg);
+extern int dm355evm_msp_read(u8 reg);
+
+
+/* command/control registers */
+#define DM355EVM_MSP_COMMAND 0x00
+# define MSP_COMMAND_NULL 0
+# define MSP_COMMAND_RESET_COLD 1
+# define MSP_COMMAND_RESET_WARM 2
+# define MSP_COMMAND_RESET_WARM_I 3
+# define MSP_COMMAND_POWEROFF 4
+# define MSP_COMMAND_IR_REINIT 5
+#define DM355EVM_MSP_STATUS 0x01
+# define MSP_STATUS_BAD_OFFSET BIT(0)
+# define MSP_STATUS_BAD_COMMAND BIT(1)
+# define MSP_STATUS_POWER_ERROR BIT(2)
+# define MSP_STATUS_RXBUF_OVERRUN BIT(3)
+#define DM355EVM_MSP_RESET 0x02 /* 0 bits == in reset */
+# define MSP_RESET_DC5 BIT(0)
+# define MSP_RESET_TVP5154 BIT(2)
+# define MSP_RESET_IMAGER BIT(3)
+# define MSP_RESET_ETHERNET BIT(4)
+# define MSP_RESET_SYS BIT(5)
+# define MSP_RESET_AIC33 BIT(7)
+
+/* GPIO registers ... bit patterns mostly match the source MSP ports */
+#define DM355EVM_MSP_LED 0x03 /* active low (MSP P4) */
+#define DM355EVM_MSP_SWITCH1 0x04 /* (MSP P5, masked) */
+# define MSP_SWITCH1_SW6_1 BIT(0)
+# define MSP_SWITCH1_SW6_2 BIT(1)
+# define MSP_SWITCH1_SW6_3 BIT(2)
+# define MSP_SWITCH1_SW6_4 BIT(3)
+# define MSP_SWITCH1_J1 BIT(4) /* NTSC/PAL */
+# define MSP_SWITCH1_MSP_INT BIT(5) /* active low */
+#define DM355EVM_MSP_SWITCH2 0x05 /* (MSP P6, masked) */
+# define MSP_SWITCH2_SW10 BIT(3)
+# define MSP_SWITCH2_SW11 BIT(4)
+# define MSP_SWITCH2_SW12 BIT(5)
+# define MSP_SWITCH2_SW13 BIT(6)
+# define MSP_SWITCH2_SW14 BIT(7)
+#define DM355EVM_MSP_SDMMC 0x06 /* (MSP P2, masked) */
+# define MSP_SDMMC_0_WP BIT(1)
+# define MSP_SDMMC_0_CD BIT(2) /* active low */
+# define MSP_SDMMC_1_WP BIT(3)
+# define MSP_SDMMC_1_CD BIT(4) /* active low */
+#define DM355EVM_MSP_FIRMREV 0x07 /* not a GPIO (out of order) */
+#define DM355EVM_MSP_VIDEO_IN 0x08 /* (MSP P3, masked) */
+# define MSP_VIDEO_IMAGER BIT(7) /* low == tvp5146 */
+
+/* power supply registers are currently omitted */
+
+/* RTC registers */
+#define DM355EVM_MSP_RTC_0 0x12 /* LSB */
+#define DM355EVM_MSP_RTC_1 0x13
+#define DM355EVM_MSP_RTC_2 0x14
+#define DM355EVM_MSP_RTC_3 0x15 /* MSB */
+
+/* input event queue registers; code == ((HIGH << 8) | LOW) */
+#define DM355EVM_MSP_INPUT_COUNT 0x16 /* decrement by reading LOW */
+#define DM355EVM_MSP_INPUT_HIGH 0x17
+#define DM355EVM_MSP_INPUT_LOW 0x18
+
+#endif /* __LINUX_I2C_DM355EVM_MSP */
diff --git a/include/linux/i2c/ds620.h b/include/linux/i2c/ds620.h
new file mode 100644
index 0000000..736bb87
--- /dev/null
+++ b/include/linux/i2c/ds620.h
@@ -0,0 +1,21 @@
+#ifndef _LINUX_DS620_H
+#define _LINUX_DS620_H
+
+#include <linux/types.h>
+#include <linux/i2c.h>
+
+/* platform data for the DS620 temperature sensor and thermostat */
+
+struct ds620_platform_data {
+ /*
+ * Thermostat output pin PO mode:
+ * 0 = always low (default)
+ * 1 = PO_LOW
+ * 2 = PO_HIGH
+ *
+ * (see Documentation/hwmon/ds620)
+ */
+ int pomode;
+};
+
+#endif /* _LINUX_DS620_H */
diff --git a/include/linux/i2c/i2c-sh_mobile.h b/include/linux/i2c/i2c-sh_mobile.h
new file mode 100644
index 0000000..beda708
--- /dev/null
+++ b/include/linux/i2c/i2c-sh_mobile.h
@@ -0,0 +1,10 @@
+#ifndef __I2C_SH_MOBILE_H__
+#define __I2C_SH_MOBILE_H__
+
+#include <linux/platform_device.h>
+
+struct i2c_sh_mobile_platform_data {
+ unsigned long bus_speed;
+};
+
+#endif /* __I2C_SH_MOBILE_H__ */
diff --git a/include/linux/i2c/isl9519.h b/include/linux/i2c/isl9519.h
new file mode 100644
index 0000000..63b2380
--- /dev/null
+++ b/include/linux/i2c/isl9519.h
@@ -0,0 +1,26 @@
+/* Copyright (c) 2010-2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+#ifndef __ISL9519_H__
+#define __ISL9519_H__
+
+struct isl_platform_data {
+ int chgcurrent;
+ int valid_n_gpio;
+ int (*chg_detection_config) (void);
+ int max_system_voltage;
+ int min_system_voltage;
+ int term_current;
+ int input_current;
+};
+
+#endif
diff --git a/include/linux/i2c/lm8323.h b/include/linux/i2c/lm8323.h
new file mode 100644
index 0000000..478d668
--- /dev/null
+++ b/include/linux/i2c/lm8323.h
@@ -0,0 +1,46 @@
+/*
+ * lm8323.h - Configuration for LM8323 keypad driver.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation (version 2 of the License only).
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __LINUX_LM8323_H
+#define __LINUX_LM8323_H
+
+#include <linux/types.h>
+
+/*
+ * Largest keycode that the chip can send, plus one,
+ * so keys can be mapped directly at the index of the
+ * LM8323 keycode instead of subtracting one.
+ */
+#define LM8323_KEYMAP_SIZE (0x7f + 1)
+
+#define LM8323_NUM_PWMS 3
+
+struct lm8323_platform_data {
+ int debounce_time; /* Time to watch for key bouncing, in ms. */
+ int active_time; /* Idle time until sleep, in ms. */
+
+ int size_x;
+ int size_y;
+ bool repeat;
+ const unsigned short *keymap;
+
+ const char *pwm_names[LM8323_NUM_PWMS];
+
+ const char *name; /* Device name. */
+};
+
+#endif /* __LINUX_LM8323_H */
diff --git a/include/linux/i2c/ltc4245.h b/include/linux/i2c/ltc4245.h
new file mode 100644
index 0000000..56bda4b
--- /dev/null
+++ b/include/linux/i2c/ltc4245.h
@@ -0,0 +1,21 @@
+/*
+ * Platform Data for LTC4245 hardware monitor chip
+ *
+ * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef LINUX_LTC4245_H
+#define LINUX_LTC4245_H
+
+#include <linux/types.h>
+
+struct ltc4245_platform_data {
+ bool use_extra_gpios;
+};
+
+#endif /* LINUX_LTC4245_H */
diff --git a/include/linux/i2c/max6639.h b/include/linux/i2c/max6639.h
new file mode 100644
index 0000000..6011c42
--- /dev/null
+++ b/include/linux/i2c/max6639.h
@@ -0,0 +1,14 @@
+#ifndef _LINUX_MAX6639_H
+#define _LINUX_MAX6639_H
+
+#include <linux/types.h>
+
+/* platform data for the MAX6639 temperature sensor and fan control */
+
+struct max6639_platform_data {
+ bool pwm_polarity; /* Polarity low (0) or high (1, default) */
+ int ppr; /* Pulses per rotation 1..4 (default == 2) */
+ int rpm_range; /* 2000, 4000 (default), 8000 or 16000 */
+};
+
+#endif /* _LINUX_MAX6639_H */
diff --git a/include/linux/i2c/max732x.h b/include/linux/i2c/max732x.h
new file mode 100644
index 0000000..c04bac8
--- /dev/null
+++ b/include/linux/i2c/max732x.h
@@ -0,0 +1,22 @@
+#ifndef __LINUX_I2C_MAX732X_H
+#define __LINUX_I2C_MAX732X_H
+
+/* platform data for the MAX732x 8/16-bit I/O expander driver */
+
+struct max732x_platform_data {
+ /* number of the first GPIO */
+ unsigned gpio_base;
+
+ /* interrupt base */
+ int irq_base;
+
+ void *context; /* param to setup/teardown */
+
+ int (*setup)(struct i2c_client *client,
+ unsigned gpio, unsigned ngpio,
+ void *context);
+ int (*teardown)(struct i2c_client *client,
+ unsigned gpio, unsigned ngpio,
+ void *context);
+};
+#endif /* __LINUX_I2C_MAX732X_H */
diff --git a/include/linux/i2c/mcs.h b/include/linux/i2c/mcs.h
new file mode 100644
index 0000000..61bb18a
--- /dev/null
+++ b/include/linux/i2c/mcs.h
@@ -0,0 +1,35 @@
+/*
+ * Copyright (C) 2009 - 2010 Samsung Electronics Co.Ltd
+ * Author: Joonyoung Shim <jy0922.shim@samsung.com>
+ * Author: HeungJun Kim <riverful.kim@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef __LINUX_MCS_H
+#define __LINUX_MCS_H
+
+#define MCS_KEY_MAP(v, c) ((((v) & 0xff) << 16) | ((c) & 0xffff))
+#define MCS_KEY_VAL(v) (((v) >> 16) & 0xff)
+#define MCS_KEY_CODE(v) ((v) & 0xffff)
+
+struct mcs_platform_data {
+ void (*poweron)(bool);
+ void (*cfg_pin)(void);
+
+ /* touchscreen */
+ unsigned int x_size;
+ unsigned int y_size;
+
+ /* touchkey */
+ const u32 *keymap;
+ unsigned int keymap_size;
+ unsigned int key_maxval;
+ bool no_autorepeat;
+};
+
+#endif /* __LINUX_MCS_H */
diff --git a/include/linux/i2c/mpr121_touchkey.h b/include/linux/i2c/mpr121_touchkey.h
new file mode 100644
index 0000000..f0bcc38
--- /dev/null
+++ b/include/linux/i2c/mpr121_touchkey.h
@@ -0,0 +1,20 @@
+/* Header file for Freescale MPR121 Capacitive Touch Sensor */
+
+#ifndef _MPR121_TOUCHKEY_H
+#define _MPR121_TOUCHKEY_H
+
+/**
+ * struct mpr121_platform_data - platform data for mpr121 sensor
+ * @keymap: pointer to array of KEY_* values representing keymap
+ * @keymap_size: size of the keymap
+ * @wakeup: configure the button as a wake-up source
+ * @vdd_uv: VDD voltage in uV
+ */
+struct mpr121_platform_data {
+ const unsigned short *keymap;
+ unsigned int keymap_size;
+ bool wakeup;
+ int vdd_uv;
+};
+
+#endif /* _MPR121_TOUCHKEY_H */
diff --git a/include/linux/i2c/pca953x.h b/include/linux/i2c/pca953x.h
new file mode 100644
index 0000000..139ba52
--- /dev/null
+++ b/include/linux/i2c/pca953x.h
@@ -0,0 +1,30 @@
+#ifndef _LINUX_PCA953X_H
+#define _LINUX_PCA953X_H
+
+#include <linux/types.h>
+#include <linux/i2c.h>
+
+/* platform data for the PCA9539 16-bit I/O expander driver */
+
+struct pca953x_platform_data {
+ /* number of the first GPIO */
+ unsigned gpio_base;
+
+ /* initial polarity inversion setting */
+ uint16_t invert;
+
+ /* interrupt base */
+ int irq_base;
+
+ void *context; /* param to setup/teardown */
+
+ int (*setup)(struct i2c_client *client,
+ unsigned gpio, unsigned ngpio,
+ void *context);
+ int (*teardown)(struct i2c_client *client,
+ unsigned gpio, unsigned ngpio,
+ void *context);
+ const char *const *names;
+};
+
+#endif /* _LINUX_PCA953X_H */
diff --git a/include/linux/i2c/pca954x.h b/include/linux/i2c/pca954x.h
new file mode 100644
index 0000000..28f1f8d
--- /dev/null
+++ b/include/linux/i2c/pca954x.h
@@ -0,0 +1,47 @@
+/*
+ *
+ * pca954x.h - I2C multiplexer/switch support
+ *
+ * Copyright (c) 2008-2009 Rodolfo Giometti <giometti@linux.it>
+ * Copyright (c) 2008-2009 Eurotech S.p.A. <info@eurotech.it>
+ * Michael Lawnick <michael.lawnick.ext@nsn.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+
+#ifndef _LINUX_I2C_PCA954X_H
+#define _LINUX_I2C_PCA954X_H
+
+/* Platform data for the PCA954x I2C multiplexers */
+
+/* Per channel initialisation data:
+ * @adap_id: bus number for the adapter. 0 = don't care
+ * @deselect_on_exit: set this entry to 1, if your H/W needs deselection
+ * of this channel after transaction.
+ *
+ */
+struct pca954x_platform_mode {
+ int adap_id;
+ unsigned int deselect_on_exit:1;
+};
+
+/* Per mux/switch data, used with i2c_register_board_info */
+struct pca954x_platform_data {
+ struct pca954x_platform_mode *modes;
+ int num_modes;
+};
+
+#endif /* _LINUX_I2C_PCA954X_H */
diff --git a/include/linux/i2c/pcf857x.h b/include/linux/i2c/pcf857x.h
new file mode 100644
index 0000000..0767a2a
--- /dev/null
+++ b/include/linux/i2c/pcf857x.h
@@ -0,0 +1,44 @@
+#ifndef __LINUX_PCF857X_H
+#define __LINUX_PCF857X_H
+
+/**
+ * struct pcf857x_platform_data - data to set up pcf857x driver
+ * @gpio_base: number of the chip's first GPIO
+ * @n_latch: optional bit-inverse of initial register value; if
+ * you leave this initialized to zero the driver will act
+ * like the chip was just reset
+ * @setup: optional callback issued once the GPIOs are valid
+ * @teardown: optional callback issued before the GPIOs are invalidated
+ * @context: optional parameter passed to setup() and teardown()
+ *
+ * In addition to the I2C_BOARD_INFO() state appropriate to each chip,
+ * the i2c_board_info used with the pcf875x driver must provide its
+ * platform_data (pointer to one of these structures) with at least
+ * the gpio_base value initialized.
+ *
+ * The @setup callback may be used with the kind of board-specific glue
+ * which hands the (now-valid) GPIOs to other drivers, or which puts
+ * devices in their initial states using these GPIOs.
+ *
+ * These GPIO chips are only "quasi-bidirectional"; read the chip specs
+ * to understand the behavior. They don't have separate registers to
+ * record which pins are used for input or output, record which output
+ * values are driven, or provide access to input values. That must be
+ * inferred by reading the chip's value and knowing the last value written
+ * to it. If you leave n_latch initialized to zero, that last written
+ * value is presumed to be all ones (as if the chip were just reset).
+ */
+struct pcf857x_platform_data {
+ unsigned gpio_base;
+ unsigned n_latch;
+
+ int (*setup)(struct i2c_client *client,
+ int gpio, unsigned ngpio,
+ void *context);
+ int (*teardown)(struct i2c_client *client,
+ int gpio, unsigned ngpio,
+ void *context);
+ void *context;
+};
+
+#endif /* __LINUX_PCF857X_H */
diff --git a/include/linux/i2c/pmbus.h b/include/linux/i2c/pmbus.h
new file mode 100644
index 0000000..69280db
--- /dev/null
+++ b/include/linux/i2c/pmbus.h
@@ -0,0 +1,45 @@
+/*
+ * Hardware monitoring driver for PMBus devices
+ *
+ * Copyright (c) 2010, 2011 Ericsson AB.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef _PMBUS_H_
+#define _PMBUS_H_
+
+/* flags */
+
+/*
+ * PMBUS_SKIP_STATUS_CHECK
+ *
+ * During register detection, skip checking the status register for
+ * communication or command errors.
+ *
+ * Some PMBus chips respond with valid data when trying to read an unsupported
+ * register. For such chips, checking the status register is mandatory when
+ * trying to determine if a chip register exists or not.
+ * Other PMBus chips don't support the STATUS_CML register, or report
+ * communication errors for no explicable reason. For such chips, checking
+ * the status register must be disabled.
+ */
+#define PMBUS_SKIP_STATUS_CHECK (1 << 0)
+
+struct pmbus_platform_data {
+ u32 flags; /* Device specific flags */
+};
+
+#endif /* _PMBUS_H_ */
diff --git a/include/linux/i2c/pxa-i2c.h b/include/linux/i2c/pxa-i2c.h
new file mode 100644
index 0000000..1a9f65e
--- /dev/null
+++ b/include/linux/i2c/pxa-i2c.h
@@ -0,0 +1,82 @@
+/*
+ * i2c_pxa.h
+ *
+ * Copyright (C) 2002 Intrinsyc Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+#ifndef _I2C_PXA_H_
+#define _I2C_PXA_H_
+
+#if 0
+#define DEF_TIMEOUT 3
+#else
+/* need a longer timeout if we're dealing with the fact we may well be
+ * looking at a multi-master environment
+*/
+#define DEF_TIMEOUT 32
+#endif
+
+#define BUS_ERROR (-EREMOTEIO)
+#define XFER_NAKED (-ECONNREFUSED)
+#define I2C_RETRY (-2000) /* an error has occurred retry transmit */
+
+/* ICR initialize bit values
+*
+* 15. FM 0 (100 Khz operation)
+* 14. UR 0 (No unit reset)
+* 13. SADIE 0 (Disables the unit from interrupting on slave addresses
+* matching its slave address)
+* 12. ALDIE 0 (Disables the unit from interrupt when it loses arbitration
+* in master mode)
+* 11. SSDIE 0 (Disables interrupts from a slave stop detected, in slave mode)
+* 10. BEIE 1 (Enable interrupts from detected bus errors, no ACK sent)
+* 9. IRFIE 1 (Enable interrupts from full buffer received)
+* 8. ITEIE 1 (Enables the I2C unit to interrupt when transmit buffer empty)
+* 7. GCD 1 (Disables i2c unit response to general call messages as a slave)
+* 6. IUE 0 (Disable unit until we change settings)
+* 5. SCLE 1 (Enables the i2c clock output for master mode (drives SCL)
+* 4. MA 0 (Only send stop with the ICR stop bit)
+* 3. TB 0 (We are not transmitting a byte initially)
+* 2. ACKNAK 0 (Send an ACK after the unit receives a byte)
+* 1. STOP 0 (Do not send a STOP)
+* 0. START 0 (Do not send a START)
+*
+*/
+#define I2C_ICR_INIT (ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD | ICR_SCLE)
+
+/* I2C status register init values
+ *
+ * 10. BED 1 (Clear bus error detected)
+ * 9. SAD 1 (Clear slave address detected)
+ * 7. IRF 1 (Clear IDBR Receive Full)
+ * 6. ITE 1 (Clear IDBR Transmit Empty)
+ * 5. ALD 1 (Clear Arbitration Loss Detected)
+ * 4. SSD 1 (Clear Slave Stop Detected)
+ */
+#define I2C_ISR_INIT 0x7FF /* status register init */
+
+struct i2c_slave_client;
+
+struct i2c_pxa_platform_data {
+ unsigned int slave_addr;
+ struct i2c_slave_client *slave;
+ unsigned int class;
+ unsigned int use_pio :1;
+ unsigned int fast_mode :1;
+};
+
+extern void pxa_set_i2c_info(struct i2c_pxa_platform_data *info);
+
+#ifdef CONFIG_PXA27x
+extern void pxa27x_set_i2c_power_info(struct i2c_pxa_platform_data *info);
+#endif
+
+#ifdef CONFIG_PXA3xx
+extern void pxa3xx_set_i2c_power_info(struct i2c_pxa_platform_data *info);
+#endif
+
+#endif
diff --git a/include/linux/i2c/s6000.h b/include/linux/i2c/s6000.h
new file mode 100644
index 0000000..d9b34bf
--- /dev/null
+++ b/include/linux/i2c/s6000.h
@@ -0,0 +1,10 @@
+#ifndef __LINUX_I2C_S6000_H
+#define __LINUX_I2C_S6000_H
+
+struct s6_i2c_platform_data {
+ const char *clock; /* the clock to use */
+ int bus_num; /* the bus number to register */
+};
+
+#endif
+
diff --git a/include/linux/i2c/smb349.h b/include/linux/i2c/smb349.h
new file mode 100644
index 0000000..fc489a7
--- /dev/null
+++ b/include/linux/i2c/smb349.h
@@ -0,0 +1,377 @@
+/* Copyright (c) 2012 Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful;
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+#ifndef __SMB349_H__
+#define __SMB349_H__
+
+#ifdef CONFIG_HTC_BATT_8960
+#include <mach/htc_charger.h>
+#endif
+
+#define SMB_CHG_CURR_REG 0x00
+#define CHG_OTHER_CURRENT_REG 0x01
+#define VAR_FUNC_REG 0x02
+#define FLOAT_VOLTAGE_REG 0x03
+#define CHG_CTRL_REG 0x04
+#define STAT_TIMER_REG 0x05
+#define PIN_ENABLE_CTRL_REG 0x06
+#define THERM_CTRL_A_REG 0x07
+#define SYSOK_USB3_SEL_REG 0x08
+#define CTRL_FUNC_REG 0x09
+#define OTG_TLIM_THERM_CNTRL_REG 0x0A
+#define LIMIT_CELL_TEMP_MONI_REG 0x0B
+#define FAULT_IRQ_REG 0x0C
+#define STATUS_IRQ_REG 0x0D
+#define SYSOK_REG 0x0E
+#define AUTO_INPUT_VOL_DET_REG 0x10
+#define I2C_BUS_REG 0x12
+#define CMD_A_REG 0x30
+#define CMD_B_REG 0x31
+#define CMD_C_REG 0x33
+#define IRQ_A_REG 0x35
+#define IRQ_B_REG 0x36
+#define IRQ_C_REG 0x37
+#define IRQ_D_REG 0x38
+#define IRQ_E_REG 0x39
+#define IRQ_F_REG 0x3A
+#define STATUS_A_REG 0x3B
+#define STATUS_B_REG 0x3C
+#define STATUS_C_REG 0x3D
+#define STATUS_D_REG 0x3E
+#define STATUS_E_REG 0x3F
+
+#define CHG_STATUS_MASK SMB349_MASK(2, 1)
+#define CHG_ENABLE_STATUS_BIT BIT(0)
+
+#define FAST_CHG_CURRENT_MASK SMB349_MASK(4, 4)
+
+
+#define SUSPEND_MODE_MASK SMB349_MASK(1, 2)
+
+#define CHARGING_ENABLE_MASK SMB349_MASK(1, 1)
+#define VOLIATILE_WRITE_PERMISSIOIN_MASK SMB349_MASK(1, 7)
+#define CURRENT_TERMINATION_MASK SMB349_MASK(1, 6)
+
+#define OTG_ENABLE_MASK SMB349_MASK(1, 4)
+#define AICL_MASK SMB349_MASK(1, 4)
+#define USBCS_MASK SMB349_MASK(1, 4)
+
+#define AC_INPUT_CURRENT_LIMIT_MASK SMB349_MASK(4, 0)
+#define DC_INPUT_CURRENT_LIMIT_MASK SMB349_MASK(4, 0)
+
+#define PRE_CHG_CURRENT_MASK SMB349_MASK(3, 5)
+
+#define USB_HC_MODE_MASK SMB349_MASK(1, 0)
+#define TERMINATION_CURRENT_MASK SMB349_MASK(3, 2)
+
+#define USB_1_5_MODE_MASK SMB349_MASK(1, 1)
+
+#define IS_SUSPEND_MODE_MASK SMB349_MASK(1, 7)
+
+#define OTG_CURRENT_MASK SMB349_MASK(2, 2)
+
+
+#define PIN_CONTROL_ACTIVE_MASK SMB349_MASK(2, 5)
+
+#define PRE_CHG_TO_FAST_CHG_THRESH_MASK SMB349_MASK(2, 6)
+#define SWITCH_FREQ_MASK SMB349_MASK(2, 6)
+#define OTG_I2C_PIN_MASK SMB349_MASK(2, 6)
+
+#define PRE_CHG_TO_FAST_CHG_ENABLE_MASK SMB349_MASK(1, 1)
+#define FLOAT_VOLTAGE_MASK SMB349_MASK(6, 0)
+
+
+#define SUSPEND_MODE_BIT BIT(2)
+#define CHG_ENABLE_BIT BIT(1)
+#define VOLATILE_W_PERM_BIT BIT(7)
+#define USB_SELECTION_BIT BIT(1)
+#define SYSTEM_FET_ENABLE_BIT BIT(7)
+#define AICL_COMPLETE_STATUS_BIT BIT(4)
+#define AUTOMATIC_INPUT_CURR_LIMIT_BIT BIT(4)
+#define I2C_CONTROL_CHARGER_BIT BIT(5)
+#define AUTOMATIC_POWER_SOURCE_DETECTION_BIT BIT(2)
+#define BATT_OV_END_CHG_BIT BIT(1)
+#define VCHG_FUNCTION BIT(0)
+#define USB_1_5_MODE BIT(1)
+#define USB_HC_MODE BIT(0)
+#define POWER_OK_STATUS BIT(0)
+#define USBCS_PIN_MODE BIT(4)
+#define USBCS_REGISTER_MODE 0
+#define CURR_TERM_END_CHG_BIT BIT(6)
+
+#define SMB349_HOT_TEMPERATURE_HARD_LIMIT_IRQ 7
+#define SMB349_HOT_TEMPERATURE_HARD_LIMIT_STATUS 6
+#define SMB349_COLD_TEMPERATURE_HARD_LIMIT_IRQ 5
+#define SMB349_COLD_TEMPERATURE_HARD_LIMIT_STATUS 4
+#define SMB349_HOT_TEMPERATURE_SOFT_LIMIT_IRQ 3
+#define SMB349_HOT_TEMPERATURE_SOFT_LIMIT_STATUS 2
+#define SMB349_COLD_TEMPERATURE_SOFT_LIMIT_IRQ 1
+#define SMB349_COLD_TEMPERATURE_SOFT_LIMIT_STATUS 0
+
+#define SMB349_BATTERY_OVER_VOLTAGE_CONDITION_IRQ 7
+#define SMB349_BATTERY_OVER_VOLTAGE_STATUS 6
+#define SMB349_MISSING_BATTER_IRQ 5
+#define SMB349_MISSING_BATTERY_STATUS 4
+#define SMB349_LOW_BATTERY_VOLTAGE_IRQ 3
+#define SMB349_LOW_BATTERY_VOLTAGE_STATUS 2
+#define SMB349_PRE_TO_FAST_CHARGE_BATTERY_VOLTAGE_IRQ 1
+#define SMB349_PRE_TO_FAST_CHARGE_BATTERY_VOLTAGE_STATUS 0
+
+#define SMB349_INTERNAL_TEMPERATURE_LIMIT_IRQ 7
+#define SMB349_INTERNAL_TEMPERATURE_LIMIT_STATUS 6
+#define SMB349_RE_CHARGE_BATTERY_THRESHOLD_IRQ 5
+#define SMB349_RE_CHARGE_BATTERY_THRESHOLD_STATUS 4
+#define SMB349_TAPER_CHARGING_MODE_IRQ 3
+#define SMB349_TAPER_CHARGING_MODE_STATUS 2
+#define SMB349_TERMINATION_CHARGING_CURRENT_HIT_IRQ 1
+#define SMB349_TERMINATION_CHARGING_CURRENT_HIT_STATUS 0
+
+#define SMB349_APSD_COMPLETED_IRQ 7
+#define SMB349_APSD_COMPLETED_STATUS 6
+#define SMB349_AICL_COMPLETE_IRQ 5
+#define SMB349_AICL_COMPLETE_STATUS 4
+#define SMB349_RESERVED_3 3
+#define SMB349_RESERVED_2 2
+#define SMB349_CHARGE_TIMEOUT_IRQ 1
+#define SMB349_CHARGE_TIMEOUT_STATUS 0
+
+#define SMB349_DCIN_OVER_VOLTAGE_STATUS 2
+
+#define SMB349_OTG_OVER_CURRENT_LIMIT_IRQ 7
+#define SMB349_OTG_OVER_CURRENT_LIMIT_STATUS 6
+#define SMB349_OTG_BATTERY_UNDER_VOLTAGE_IRQ 5
+#define SMB349_OTG_BATTERY_UNDER_VOLTAGE_STATUS 4
+#define SMB349_OTG_DETECTION_IRQ 3
+#define SMB349_OTG_DETECTION_STATUS 2
+#define SMB349_POWER_OK_IRQ 1
+#define SMB349_POWER_OK_STATUS 0
+
+
+#define SMB349_FAST_CHG_MIN_MA 1000
+#define SMB349_FAST_CHG_STEP_MA 200
+#define SMB349_FAST_CHG_MAX_MA 4000
+#define SMB349_FAST_CHG_SHIFT 4
+#define SMB349_PRE_CHG_SHIFT 5
+
+#define SMB349_OTG_I2C_PIN_SHIFT 6
+
+#define SMB349_OTG_I2C_CONTROL 0x0
+#define SMB349_OTG_PIN_CONTROL 0x1
+
+#define SMB34X_OTG_CURR_LIMIT_SHIFT 2
+#define SMB349_SWITCH_FREQ_SHIFT 6
+
+#define SMB349_PIN_CONTROL_SHIFT 5
+#define SMB349_USBCS_REGISTER_CTRL 0
+#define SMB349_USBCS_PIN_CTRL 1
+
+#define SMB349_NO_CHARGING 0
+#define SMB349_PRE_CHARGING 1
+#define SMB349_FAST_CHARGING 2
+#define SMB349_TAPER_CHARGING 3
+
+
+
+#define SMB349_FLOAT_VOL_4000_MV 0x1B
+#define SMB349_FLOAT_VOL_4200_MV 0x25
+#define SMB349_FLOAT_VOL_4220_MV 0x26
+#define SMB349_FLOAT_VOL_4240_MV 0x27
+#define SMB349_FLOAT_VOL_4260_MV 0x28
+#define SMB349_FLOAT_VOL_4280_MV 0x29
+#define SMB349_FLOAT_VOL_4300_MV 0x2A
+#define SMB349_FLOAT_VOL_4320_MV 0x2B
+#define SMB349_FLOAT_VOL_4340_MV 0x2C
+#define SMB349_FLOAT_VOL_4350_MV 0x2D
+
+
+#define SMB_OTG_CURR_LIMIT_250MA 0x0
+#define SMB_OTG_CURR_LIMIT_500MA 0x1
+#define SMB_OTG_CURR_LIMIT_750MA 0x2
+#define SMB_OTG_CURR_LIMIT_1000MA 0x3
+
+
+#define SMB349_I2C_CONTROL_ACTIVE_HIGH 0x0
+#define SMB349_I2C_CONTROL_ACTIVE_LOW 0x1
+#define SMB349_PIN_CONTROL_ACTIVE_HIGH 0x2
+#define SMB349_PIN_CONTROL_ACTIVE_LOW 0x3
+
+#define AICL_RESULT_500MA 0x0
+#define AICL_RESULT_900MA 0x1
+#define AICL_RESULT_1000MA 0x2
+#define AICL_RESULT_1100MA 0x3
+#define AICL_RESULT_1200MA 0x4
+#define AICL_RESULT_1300MA 0x5
+#define AICL_RESULT_1500MA 0x6
+#define AICL_RESULT_1600MA 0x7
+#define AICL_RESULT_1700MA 0x8
+#define AICL_RESULT_1800MA 0x9
+#define AICL_RESULT_2000MA 0xa
+#define AICL_RESULT_2200MA 0xb
+#define AICL_RESULT_2400MA 0xc
+#define AICL_RESULT_2500MA 0xd
+#define AICL_RESULT_3000MA 0xe
+#define AICL_RESULT_3500MA 0xf
+
+#define SWITCH_FREQ_750KHZ 0x0
+#define SWITCH_FREQ_1MHZ 0x1
+#define SWITCH_FREQ_1D5MHZ 0x2
+#define SWITCH_FREQ_3MHZ 0x3
+
+#define SMB349_USB_MODE 0
+#define SMB349_HC_MODE 1
+
+#define AICL_ENABLE 1
+#define AICL_DISABLE 0
+
+
+#define FAST_CHARGE_500MA 0x0
+#define FAST_CHARGE_600MA 0x1
+#define FAST_CHARGE_700MA 0x2
+#define FAST_CHARGE_800MA 0x3
+#define FAST_CHARGE_900MA 0x4
+#define FAST_CHARGE_1000MA 0x5
+#define FAST_CHARGE_1100MA 0x6
+#define FAST_CHARGE_1200MA 0x7
+#define FAST_CHARGE_1300MA 0x8
+#define FAST_CHARGE_1400MA 0x9
+#define FAST_CHARGE_1500MA 0xa
+#define FAST_CHARGE_1600MA 0xb
+#define FAST_CHARGE_1700MA 0xc
+#define FAST_CHARGE_1800MA 0xd
+#define FAST_CHARGE_1900MA 0xe
+#define FAST_CHARGE_2000MA 0xf
+
+
+#define SMB340_FASTCHG_1000MA 0x0
+#define SMB340_FASTCHG_1200MA 0x1
+#define SMB340_FASTCHG_1400MA 0x2
+#define SMB340_FASTCHG_1600MA 0x3
+#define SMB340_FASTCHG_1800MA 0x4
+#define SMB340_FASTCHG_2000MA 0x5
+#define SMB340_FASTCHG_2200MA 0x6
+#define SMB340_FASTCHG_2400MA 0x7
+#define SMB340_FASTCHG_2600MA 0x8
+#define SMB340_FASTCHG_2800MA 0x9
+#define SMB340_FASTCHG_3000MA 0xa
+#define SMB340_FASTCHG_3200MA 0xb
+#define SMB340_FASTCHG_3400MA 0xc
+#define SMB340_FASTCHG_3600MA 0xd
+#define SMB340_FASTCHG_3800MA 0xe
+#define SMB340_FASTCHG_4000MA 0xf
+
+
+
+#define DC_INPUT_500MA 0x0
+#define DC_INPUT_900MA 0x1
+#define DC_INPUT_1000MA 0x2
+#define DC_INPUT_1100MA 0x3
+#define DC_INPUT_1200MA 0x4
+#define DC_INPUT_1300MA 0x5
+#define DC_INPUT_1500MA 0x6
+#define DC_INPUT_1600MA 0x7
+#define DC_INPUT_1700MA 0x8
+#define DC_INPUT_1800MA 0x9
+#define DC_INPUT_2000MA 0xa
+#define DC_INPUT_2200MA 0xb
+#define DC_INPUT_2400MA 0xc
+#define DC_INPUT_2500MA 0xd
+#define DC_INPUT_3000MA 0xe
+#define DC_INPUT_3500MA 0xf
+
+#define PRECHG_CURR_100MA 0x0
+#define PRECHG_CURR_150MA 0x1
+#define PRECHG_CURR_200MA 0x2
+#define PRECHG_CURR_250MA 0x3
+#define PRECHG_CURR_300MA 0x4
+#define PRECHG_CURR_350MA 0x5
+#define PRECHG_CURR_50MA 0x6
+
+#define SMB340_PRECHG_CURR_200MA 0x0
+#define SMB340_PRECHG_CURR_300MA 0x1
+#define SMB340_PRECHG_CURR_400MA 0x2
+#define SMB340_PRECHG_CURR_500MA 0x3
+#define SMB340_PRECHG_CURR_600MA 0x4
+#define SMB340_PRECHG_CURR_700MA 0x5
+#define SMB340_PRECHG_CURR_100MA 0x6
+
+
+#define SMB_349 1
+#define SMB_340 2
+
+enum smb349_thermal_state {
+ STATE_HI_V_SCRN_ON = 1,
+ STATE_LO_V_SCRN_ON,
+ STATE_HI_V_SCRN_OFF,
+ STATE_LO_V_SCRN_OFF,
+};
+
+struct smb349_chg_int_notifier {
+ struct list_head notifier_link;
+ const char *name;
+ void (*func)(int int_reg, int value);
+};
+
+struct smb349_platform_data {
+ int chg_susp_gpio;
+ int chg_current_ma;
+ int chip_rev;
+#ifdef CONFIG_SUPPORT_DQ_BATTERY
+ int dq_result;
+#endif
+ int aicl_result_threshold;
+ int dc_input_max;
+ int aicl_on;
+};
+
+struct smb349_charger_batt_param {
+ int max_voltage;
+ int cool_bat_voltage;
+ int warm_bat_voltage;
+};
+int smb349_set_AICL_mode(unsigned int enable);
+int smb349_allow_fast_charging_setting(void);
+int smb349_allow_volatile_wrtting(void);
+int smb349_enable_charging(bool enable);
+int smb349_eoc_notify(enum htc_extchg_event_type main_event);
+int smb349_event_notify(enum htc_extchg_event_type extchg_event);
+int smb349_temp_notify(enum htc_extchg_event_type main_event);
+int smb349_enable_5v_output(bool mhl_in);
+int smb349_config(void);
+void smb349_dbg(void);
+int smb349_dump_reg(u8 reg);
+void smb349_partial_reg_dump(void);
+int smb349_dump_all(void);
+int smb349_is_AICL_complete(void);
+int smb349_is_AICL_enabled(void);
+int smb349_is_charger_bit_low_active(void);
+int smb349_is_charger_error(void);
+int smb349_adjust_max_chg_vol(enum htc_extchg_event_type main_event);
+int smb349_is_charging_enabled(int *result);
+int smb349_is_batt_temp_fault_disable_chg(int *result);
+int smb349_get_i2c_slave_id(void);
+int smb349_is_hc_mode(void);
+int smb349_is_usbcs_register_mode(void);
+int smb349_masked_write(int reg, u8 mask, u8 val);
+int smb349_not_allow_charging_cycle_end(void);
+int smb349_enable_pwrsrc(bool enable);
+int smb349_set_pwrsrc_and_charger_enable(enum htc_power_source_type src, bool chg_enable, bool pwrsrc_enable);
+int smb349_set_hc_mode(unsigned int enable);
+int smb349_switch_usbcs_mode(int mode);
+int smb349_limit_charge_enable(bool enable);
+int smb349_get_charging_src(int *result);
+int smb349_get_charging_enabled(int *result);
+int smb349_is_charger_overvoltage(int* result);
+int smb349_charger_get_attr_text(char *buf, int size);
+int smb349_start_charging(void *ctx);
+int smb349_stop_charging(void *ctx);
+bool smb349_is_trickle_charging(void *ctx);
+#endif
diff --git a/include/linux/i2c/sx150x.h b/include/linux/i2c/sx150x.h
new file mode 100644
index 0000000..a35142e
--- /dev/null
+++ b/include/linux/i2c/sx150x.h
@@ -0,0 +1,30 @@
+/*
+ * Driver for the Semtech SX150x I2C GPIO Expanders
+ *
+ * Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#ifndef __LINUX_I2C_SX150X_H
+#define __LINUX_I2C_SX150X_H
+
+struct sx150x_platform_data {
+ unsigned gpio_base;
+ bool oscio_is_gpo;
+ u16 io_pullup_ena;
+ u16 io_pulldn_ena;
+ u16 io_open_drain_ena;
+ u16 io_polarity;
+ int irq_summary;
+ unsigned irq_base;
+ bool reset_during_probe;
+};
+
+#endif
diff --git a/include/linux/i2c/tc35876x.h b/include/linux/i2c/tc35876x.h
new file mode 100644
index 0000000..cd6a51c
--- /dev/null
+++ b/include/linux/i2c/tc35876x.h
@@ -0,0 +1,11 @@
+
+#ifndef _TC35876X_H
+#define _TC35876X_H
+
+struct tc35876x_platform_data {
+ int gpio_bridge_reset;
+ int gpio_panel_bl_en;
+ int gpio_panel_vadd;
+};
+
+#endif /* _TC35876X_H */
diff --git a/include/linux/i2c/tps65010.h b/include/linux/i2c/tps65010.h
new file mode 100644
index 0000000..08aa922
--- /dev/null
+++ b/include/linux/i2c/tps65010.h
@@ -0,0 +1,205 @@
+/* linux/i2c/tps65010.h
+ *
+ * Functions to access TPS65010 power management device.
+ *
+ * Copyright (C) 2004 Dirk Behme <dirk.behme@de.bosch.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __LINUX_I2C_TPS65010_H
+#define __LINUX_I2C_TPS65010_H
+
+/*
+ * ----------------------------------------------------------------------------
+ * Registers, all 8 bits
+ * ----------------------------------------------------------------------------
+ */
+
+#define TPS_CHGSTATUS 0x01
+# define TPS_CHG_USB (1 << 7)
+# define TPS_CHG_AC (1 << 6)
+# define TPS_CHG_THERM (1 << 5)
+# define TPS_CHG_TERM (1 << 4)
+# define TPS_CHG_TAPER_TMO (1 << 3)
+# define TPS_CHG_CHG_TMO (1 << 2)
+# define TPS_CHG_PRECHG_TMO (1 << 1)
+# define TPS_CHG_TEMP_ERR (1 << 0)
+#define TPS_REGSTATUS 0x02
+# define TPS_REG_ONOFF (1 << 7)
+# define TPS_REG_COVER (1 << 6)
+# define TPS_REG_UVLO (1 << 5)
+# define TPS_REG_NO_CHG (1 << 4) /* tps65013 */
+# define TPS_REG_PG_LD02 (1 << 3)
+# define TPS_REG_PG_LD01 (1 << 2)
+# define TPS_REG_PG_MAIN (1 << 1)
+# define TPS_REG_PG_CORE (1 << 0)
+#define TPS_MASK1 0x03
+#define TPS_MASK2 0x04
+#define TPS_ACKINT1 0x05
+#define TPS_ACKINT2 0x06
+#define TPS_CHGCONFIG 0x07
+# define TPS_CHARGE_POR (1 << 7) /* 65010/65012 */
+# define TPS65013_AUA (1 << 7) /* 65011/65013 */
+# define TPS_CHARGE_RESET (1 << 6)
+# define TPS_CHARGE_FAST (1 << 5)
+# define TPS_CHARGE_CURRENT (3 << 3)
+# define TPS_VBUS_500MA (1 << 2)
+# define TPS_VBUS_CHARGING (1 << 1)
+# define TPS_CHARGE_ENABLE (1 << 0)
+#define TPS_LED1_ON 0x08
+#define TPS_LED1_PER 0x09
+#define TPS_LED2_ON 0x0a
+#define TPS_LED2_PER 0x0b
+#define TPS_VDCDC1 0x0c
+# define TPS_ENABLE_LP (1 << 3)
+#define TPS_VDCDC2 0x0d
+# define TPS_LP_COREOFF (1 << 7)
+# define TPS_VCORE_1_8V (7<<4)
+# define TPS_VCORE_1_5V (6 << 4)
+# define TPS_VCORE_1_4V (5 << 4)
+# define TPS_VCORE_1_3V (4 << 4)
+# define TPS_VCORE_1_2V (3 << 4)
+# define TPS_VCORE_1_1V (2 << 4)
+# define TPS_VCORE_1_0V (1 << 4)
+# define TPS_VCORE_0_85V (0 << 4)
+# define TPS_VCORE_LP_1_2V (3 << 2)
+# define TPS_VCORE_LP_1_1V (2 << 2)
+# define TPS_VCORE_LP_1_0V (1 << 2)
+# define TPS_VCORE_LP_0_85V (0 << 2)
+# define TPS_VIB (1 << 1)
+# define TPS_VCORE_DISCH (1 << 0)
+#define TPS_VREGS1 0x0e
+# define TPS_LDO2_ENABLE (1 << 7)
+# define TPS_LDO2_OFF (1 << 6)
+# define TPS_VLDO2_3_0V (3 << 4)
+# define TPS_VLDO2_2_75V (2 << 4)
+# define TPS_VLDO2_2_5V (1 << 4)
+# define TPS_VLDO2_1_8V (0 << 4)
+# define TPS_LDO1_ENABLE (1 << 3)
+# define TPS_LDO1_OFF (1 << 2)
+# define TPS_VLDO1_3_0V (3 << 0)
+# define TPS_VLDO1_2_75V (2 << 0)
+# define TPS_VLDO1_2_5V (1 << 0)
+# define TPS_VLDO1_ADJ (0 << 0)
+#define TPS_MASK3 0x0f
+#define TPS_DEFGPIO 0x10
+
+/*
+ * ----------------------------------------------------------------------------
+ * Macros used by exported functions
+ * ----------------------------------------------------------------------------
+ */
+
+#define LED1 1
+#define LED2 2
+#define OFF 0
+#define ON 1
+#define BLINK 2
+#define GPIO1 1
+#define GPIO2 2
+#define GPIO3 3
+#define GPIO4 4
+#define LOW 0
+#define HIGH 1
+
+/*
+ * ----------------------------------------------------------------------------
+ * Exported functions
+ * ----------------------------------------------------------------------------
+ */
+
+/* Draw from VBUS:
+ * 0 mA -- DON'T DRAW (might supply power instead)
+ * 100 mA -- usb unit load (slowest charge rate)
+ * 500 mA -- usb high power (fast battery charge)
+ */
+extern int tps65010_set_vbus_draw(unsigned mA);
+
+/* tps65010_set_gpio_out_value parameter:
+ * gpio: GPIO1, GPIO2, GPIO3 or GPIO4
+ * value: LOW or HIGH
+ */
+extern int tps65010_set_gpio_out_value(unsigned gpio, unsigned value);
+
+/* tps65010_set_led parameter:
+ * led: LED1 or LED2
+ * mode: ON, OFF or BLINK
+ */
+extern int tps65010_set_led(unsigned led, unsigned mode);
+
+/* tps65010_set_vib parameter:
+ * value: ON or OFF
+ */
+extern int tps65010_set_vib(unsigned value);
+
+/* tps65010_set_low_pwr parameter:
+ * mode: ON or OFF
+ */
+extern int tps65010_set_low_pwr(unsigned mode);
+
+/* tps65010_config_vregs1 parameter:
+ * value to be written to VREGS1 register
+ * Note: The complete register is written, set all bits you need
+ */
+extern int tps65010_config_vregs1(unsigned value);
+
+/* tps65013_set_low_pwr parameter:
+ * mode: ON or OFF
+ */
+extern int tps65013_set_low_pwr(unsigned mode);
+
+/* tps65010_set_vdcdc2
+ * value to be written to VDCDC2
+ */
+extern int tps65010_config_vdcdc2(unsigned value);
+
+struct i2c_client;
+
+/**
+ * struct tps65010_board - packages GPIO and LED lines
+ * @base: the GPIO number to assign to GPIO-1
+ * @outmask: bit (N-1) is set to allow GPIO-N to be used as an
+ * (open drain) output
+ * @setup: optional callback issued once the GPIOs are valid
+ * @teardown: optional callback issued before the GPIOs are invalidated
+ * @context: optional parameter passed to setup() and teardown()
+ *
+ * Board data may be used to package the GPIO (and LED) lines for use
+ * in by the generic GPIO and LED frameworks. The first four GPIOs
+ * starting at gpio_base are GPIO1..GPIO4. The next two are LED1/nPG
+ * and LED2 (with hardware blinking capability, not currently exposed).
+ *
+ * The @setup callback may be used with the kind of board-specific glue
+ * which hands the (now-valid) GPIOs to other drivers, or which puts
+ * devices in their initial states using these GPIOs.
+ */
+struct tps65010_board {
+ int base;
+ unsigned outmask;
+
+ int (*setup)(struct i2c_client *client, void *context);
+ int (*teardown)(struct i2c_client *client, void *context);
+ void *context;
+};
+
+#endif /* __LINUX_I2C_TPS65010_H */
+
diff --git a/include/linux/i2c/tsc2007.h b/include/linux/i2c/tsc2007.h
new file mode 100644
index 0000000..506a9f7
--- /dev/null
+++ b/include/linux/i2c/tsc2007.h
@@ -0,0 +1,24 @@
+#ifndef __LINUX_I2C_TSC2007_H
+#define __LINUX_I2C_TSC2007_H
+
+/* linux/i2c/tsc2007.h */
+
+struct tsc2007_platform_data {
+ u16 model; /* 2007. */
+ u16 x_plate_ohms; /* must be non-zero value */
+ u16 max_rt; /* max. resistance above which samples are ignored */
+ unsigned long poll_delay; /* delay (in ms) after pen-down event
+ before polling starts */
+ unsigned long poll_period; /* time (in ms) between samples */
+ int fuzzx; /* fuzz factor for X, Y and pressure axes */
+ int fuzzy;
+ int fuzzz;
+
+ int (*get_pendown_state)(void);
+ void (*clear_penirq)(void); /* If needed, clear 2nd level
+ interrupt source */
+ int (*init_platform_hw)(void);
+ void (*exit_platform_hw)(void);
+};
+
+#endif
diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h
new file mode 100644
index 0000000..1f90de0
--- /dev/null
+++ b/include/linux/i2c/twl.h
@@ -0,0 +1,846 @@
+/*
+ * twl4030.h - header for TWL4030 PM and audio CODEC device
+ *
+ * Copyright (C) 2005-2006 Texas Instruments, Inc.
+ *
+ * Based on tlv320aic23.c:
+ * Copyright (c) by Kai Svahn <kai.svahn@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef __TWL_H_
+#define __TWL_H_
+
+#include <linux/types.h>
+#include <linux/input/matrix_keypad.h>
+
+/*
+ * Using the twl4030 core we address registers using a pair
+ * { module id, relative register offset }
+ * which that core then maps to the relevant
+ * { i2c slave, absolute register address }
+ *
+ * The module IDs are meaningful only to the twl4030 core code,
+ * which uses them as array indices to look up the first register
+ * address each module uses within a given i2c slave.
+ */
+
+/* Slave 0 (i2c address 0x48) */
+#define TWL4030_MODULE_USB 0x00
+
+/* Slave 1 (i2c address 0x49) */
+#define TWL4030_MODULE_AUDIO_VOICE 0x01
+#define TWL4030_MODULE_GPIO 0x02
+#define TWL4030_MODULE_INTBR 0x03
+#define TWL4030_MODULE_PIH 0x04
+#define TWL4030_MODULE_TEST 0x05
+
+/* Slave 2 (i2c address 0x4a) */
+#define TWL4030_MODULE_KEYPAD 0x06
+#define TWL4030_MODULE_MADC 0x07
+#define TWL4030_MODULE_INTERRUPTS 0x08
+#define TWL4030_MODULE_LED 0x09
+#define TWL4030_MODULE_MAIN_CHARGE 0x0A
+#define TWL4030_MODULE_PRECHARGE 0x0B
+#define TWL4030_MODULE_PWM0 0x0C
+#define TWL4030_MODULE_PWM1 0x0D
+#define TWL4030_MODULE_PWMA 0x0E
+#define TWL4030_MODULE_PWMB 0x0F
+
+#define TWL5031_MODULE_ACCESSORY 0x10
+#define TWL5031_MODULE_INTERRUPTS 0x11
+
+/* Slave 3 (i2c address 0x4b) */
+#define TWL4030_MODULE_BACKUP 0x12
+#define TWL4030_MODULE_INT 0x13
+#define TWL4030_MODULE_PM_MASTER 0x14
+#define TWL4030_MODULE_PM_RECEIVER 0x15
+#define TWL4030_MODULE_RTC 0x16
+#define TWL4030_MODULE_SECURED_REG 0x17
+
+#define TWL_MODULE_USB TWL4030_MODULE_USB
+#define TWL_MODULE_AUDIO_VOICE TWL4030_MODULE_AUDIO_VOICE
+#define TWL_MODULE_PIH TWL4030_MODULE_PIH
+#define TWL_MODULE_MADC TWL4030_MODULE_MADC
+#define TWL_MODULE_MAIN_CHARGE TWL4030_MODULE_MAIN_CHARGE
+#define TWL_MODULE_PM_MASTER TWL4030_MODULE_PM_MASTER
+#define TWL_MODULE_PM_RECEIVER TWL4030_MODULE_PM_RECEIVER
+#define TWL_MODULE_RTC TWL4030_MODULE_RTC
+#define TWL_MODULE_PWM TWL4030_MODULE_PWM0
+
+#define TWL6030_MODULE_ID0 0x0D
+#define TWL6030_MODULE_ID1 0x0E
+#define TWL6030_MODULE_ID2 0x0F
+
+#define GPIO_INTR_OFFSET 0
+#define KEYPAD_INTR_OFFSET 1
+#define BCI_INTR_OFFSET 2
+#define MADC_INTR_OFFSET 3
+#define USB_INTR_OFFSET 4
+#define CHARGERFAULT_INTR_OFFSET 5
+#define BCI_PRES_INTR_OFFSET 9
+#define USB_PRES_INTR_OFFSET 10
+#define RTC_INTR_OFFSET 11
+
+/*
+ * Offset from TWL6030_IRQ_BASE / pdata->irq_base
+ */
+#define PWR_INTR_OFFSET 0
+#define HOTDIE_INTR_OFFSET 12
+#define SMPSLDO_INTR_OFFSET 13
+#define BATDETECT_INTR_OFFSET 14
+#define SIMDETECT_INTR_OFFSET 15
+#define MMCDETECT_INTR_OFFSET 16
+#define GASGAUGE_INTR_OFFSET 17
+#define USBOTG_INTR_OFFSET 4
+#define CHARGER_INTR_OFFSET 2
+#define RSV_INTR_OFFSET 0
+
+/* INT register offsets */
+#define REG_INT_STS_A 0x00
+#define REG_INT_STS_B 0x01
+#define REG_INT_STS_C 0x02
+
+#define REG_INT_MSK_LINE_A 0x03
+#define REG_INT_MSK_LINE_B 0x04
+#define REG_INT_MSK_LINE_C 0x05
+
+#define REG_INT_MSK_STS_A 0x06
+#define REG_INT_MSK_STS_B 0x07
+#define REG_INT_MSK_STS_C 0x08
+
+/* MASK INT REG GROUP A */
+#define TWL6030_PWR_INT_MASK 0x07
+#define TWL6030_RTC_INT_MASK 0x18
+#define TWL6030_HOTDIE_INT_MASK 0x20
+#define TWL6030_SMPSLDOA_INT_MASK 0xC0
+
+/* MASK INT REG GROUP B */
+#define TWL6030_SMPSLDOB_INT_MASK 0x01
+#define TWL6030_BATDETECT_INT_MASK 0x02
+#define TWL6030_SIMDETECT_INT_MASK 0x04
+#define TWL6030_MMCDETECT_INT_MASK 0x08
+#define TWL6030_GPADC_INT_MASK 0x60
+#define TWL6030_GASGAUGE_INT_MASK 0x80
+
+/* MASK INT REG GROUP C */
+#define TWL6030_USBOTG_INT_MASK 0x0F
+#define TWL6030_CHARGER_CTRL_INT_MASK 0x10
+#define TWL6030_CHARGER_FAULT_INT_MASK 0x60
+
+#define TWL6030_MMCCTRL 0xEE
+#define VMMC_AUTO_OFF (0x1 << 3)
+#define SW_FC (0x1 << 2)
+#define STS_MMC 0x1
+
+#define TWL6030_CFG_INPUT_PUPD3 0xF2
+#define MMC_PU (0x1 << 3)
+#define MMC_PD (0x1 << 2)
+
+#define TWL_SIL_TYPE(rev) ((rev) & 0x00FFFFFF)
+#define TWL_SIL_REV(rev) ((rev) >> 24)
+#define TWL_SIL_5030 0x09002F
+#define TWL5030_REV_1_0 0x00
+#define TWL5030_REV_1_1 0x10
+#define TWL5030_REV_1_2 0x30
+
+#define TWL4030_CLASS_ID 0x4030
+#define TWL6030_CLASS_ID 0x6030
+unsigned int twl_rev(void);
+#define GET_TWL_REV (twl_rev())
+#define TWL_CLASS_IS(class, id) \
+static inline int twl_class_is_ ##class(void) \
+{ \
+ return ((id) == (GET_TWL_REV)) ? 1 : 0; \
+}
+
+TWL_CLASS_IS(4030, TWL4030_CLASS_ID)
+TWL_CLASS_IS(6030, TWL6030_CLASS_ID)
+
+#define TWL6025_SUBCLASS BIT(4) /* TWL6025 has changed registers */
+
+/*
+ * Read and write single 8-bit registers
+ */
+int twl_i2c_write_u8(u8 mod_no, u8 val, u8 reg);
+int twl_i2c_read_u8(u8 mod_no, u8 *val, u8 reg);
+
+/*
+ * Read and write several 8-bit registers at once.
+ *
+ * IMPORTANT: For twl_i2c_write(), allocate num_bytes + 1
+ * for the value, and populate your data starting at offset 1.
+ */
+int twl_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
+int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
+
+int twl_get_type(void);
+int twl_get_version(void);
+
+int twl6030_interrupt_unmask(u8 bit_mask, u8 offset);
+int twl6030_interrupt_mask(u8 bit_mask, u8 offset);
+
+/* Card detect Configuration for MMC1 Controller on OMAP4 */
+#ifdef CONFIG_TWL4030_CORE
+int twl6030_mmc_card_detect_config(void);
+#else
+static inline int twl6030_mmc_card_detect_config(void)
+{
+ pr_debug("twl6030_mmc_card_detect_config not supported\n");
+ return 0;
+}
+#endif
+
+/* MMC1 Controller on OMAP4 uses Phoenix irq for Card detect */
+#ifdef CONFIG_TWL4030_CORE
+int twl6030_mmc_card_detect(struct device *dev, int slot);
+#else
+static inline int twl6030_mmc_card_detect(struct device *dev, int slot)
+{
+ pr_debug("Call back twl6030_mmc_card_detect not supported\n");
+ return -EIO;
+}
+#endif
+/*----------------------------------------------------------------------*/
+
+/*
+ * NOTE: at up to 1024 registers, this is a big chip.
+ *
+ * Avoid putting register declarations in this file, instead of into
+ * a driver-private file, unless some of the registers in a block
+ * need to be shared with other drivers. One example is blocks that
+ * have Secondary IRQ Handler (SIH) registers.
+ */
+
+#define TWL4030_SIH_CTRL_EXCLEN_MASK BIT(0)
+#define TWL4030_SIH_CTRL_PENDDIS_MASK BIT(1)
+#define TWL4030_SIH_CTRL_COR_MASK BIT(2)
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * GPIO Block Register offsets (use TWL4030_MODULE_GPIO)
+ */
+
+#define REG_GPIODATAIN1 0x0
+#define REG_GPIODATAIN2 0x1
+#define REG_GPIODATAIN3 0x2
+#define REG_GPIODATADIR1 0x3
+#define REG_GPIODATADIR2 0x4
+#define REG_GPIODATADIR3 0x5
+#define REG_GPIODATAOUT1 0x6
+#define REG_GPIODATAOUT2 0x7
+#define REG_GPIODATAOUT3 0x8
+#define REG_CLEARGPIODATAOUT1 0x9
+#define REG_CLEARGPIODATAOUT2 0xA
+#define REG_CLEARGPIODATAOUT3 0xB
+#define REG_SETGPIODATAOUT1 0xC
+#define REG_SETGPIODATAOUT2 0xD
+#define REG_SETGPIODATAOUT3 0xE
+#define REG_GPIO_DEBEN1 0xF
+#define REG_GPIO_DEBEN2 0x10
+#define REG_GPIO_DEBEN3 0x11
+#define REG_GPIO_CTRL 0x12
+#define REG_GPIOPUPDCTR1 0x13
+#define REG_GPIOPUPDCTR2 0x14
+#define REG_GPIOPUPDCTR3 0x15
+#define REG_GPIOPUPDCTR4 0x16
+#define REG_GPIOPUPDCTR5 0x17
+#define REG_GPIO_ISR1A 0x19
+#define REG_GPIO_ISR2A 0x1A
+#define REG_GPIO_ISR3A 0x1B
+#define REG_GPIO_IMR1A 0x1C
+#define REG_GPIO_IMR2A 0x1D
+#define REG_GPIO_IMR3A 0x1E
+#define REG_GPIO_ISR1B 0x1F
+#define REG_GPIO_ISR2B 0x20
+#define REG_GPIO_ISR3B 0x21
+#define REG_GPIO_IMR1B 0x22
+#define REG_GPIO_IMR2B 0x23
+#define REG_GPIO_IMR3B 0x24
+#define REG_GPIO_EDR1 0x28
+#define REG_GPIO_EDR2 0x29
+#define REG_GPIO_EDR3 0x2A
+#define REG_GPIO_EDR4 0x2B
+#define REG_GPIO_EDR5 0x2C
+#define REG_GPIO_SIH_CTRL 0x2D
+
+/* Up to 18 signals are available as GPIOs, when their
+ * pins are not assigned to another use (such as ULPI/USB).
+ */
+#define TWL4030_GPIO_MAX 18
+
+/*----------------------------------------------------------------------*/
+
+/*Interface Bit Register (INTBR) offsets
+ *(Use TWL_4030_MODULE_INTBR)
+ */
+
+#define REG_IDCODE_7_0 0x00
+#define REG_IDCODE_15_8 0x01
+#define REG_IDCODE_16_23 0x02
+#define REG_IDCODE_31_24 0x03
+#define REG_GPPUPDCTR1 0x0F
+#define REG_UNLOCK_TEST_REG 0x12
+
+/*I2C1 and I2C4(SR) SDA/SCL pull-up control bits */
+
+#define I2C_SCL_CTRL_PU BIT(0)
+#define I2C_SDA_CTRL_PU BIT(2)
+#define SR_I2C_SCL_CTRL_PU BIT(4)
+#define SR_I2C_SDA_CTRL_PU BIT(6)
+
+#define TWL_EEPROM_R_UNLOCK 0x49
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Keypad register offsets (use TWL4030_MODULE_KEYPAD)
+ * ... SIH/interrupt only
+ */
+
+#define TWL4030_KEYPAD_KEYP_ISR1 0x11
+#define TWL4030_KEYPAD_KEYP_IMR1 0x12
+#define TWL4030_KEYPAD_KEYP_ISR2 0x13
+#define TWL4030_KEYPAD_KEYP_IMR2 0x14
+#define TWL4030_KEYPAD_KEYP_SIR 0x15 /* test register */
+#define TWL4030_KEYPAD_KEYP_EDR 0x16
+#define TWL4030_KEYPAD_KEYP_SIH_CTRL 0x17
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Multichannel ADC register offsets (use TWL4030_MODULE_MADC)
+ * ... SIH/interrupt only
+ */
+
+#define TWL4030_MADC_ISR1 0x61
+#define TWL4030_MADC_IMR1 0x62
+#define TWL4030_MADC_ISR2 0x63
+#define TWL4030_MADC_IMR2 0x64
+#define TWL4030_MADC_SIR 0x65 /* test register */
+#define TWL4030_MADC_EDR 0x66
+#define TWL4030_MADC_SIH_CTRL 0x67
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS)
+ */
+
+#define TWL4030_INTERRUPTS_BCIISR1A 0x0
+#define TWL4030_INTERRUPTS_BCIISR2A 0x1
+#define TWL4030_INTERRUPTS_BCIIMR1A 0x2
+#define TWL4030_INTERRUPTS_BCIIMR2A 0x3
+#define TWL4030_INTERRUPTS_BCIISR1B 0x4
+#define TWL4030_INTERRUPTS_BCIISR2B 0x5
+#define TWL4030_INTERRUPTS_BCIIMR1B 0x6
+#define TWL4030_INTERRUPTS_BCIIMR2B 0x7
+#define TWL4030_INTERRUPTS_BCISIR1 0x8 /* test register */
+#define TWL4030_INTERRUPTS_BCISIR2 0x9 /* test register */
+#define TWL4030_INTERRUPTS_BCIEDR1 0xa
+#define TWL4030_INTERRUPTS_BCIEDR2 0xb
+#define TWL4030_INTERRUPTS_BCIEDR3 0xc
+#define TWL4030_INTERRUPTS_BCISIHCTRL 0xd
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Power Interrupt block register offsets (use TWL4030_MODULE_INT)
+ */
+
+#define TWL4030_INT_PWR_ISR1 0x0
+#define TWL4030_INT_PWR_IMR1 0x1
+#define TWL4030_INT_PWR_ISR2 0x2
+#define TWL4030_INT_PWR_IMR2 0x3
+#define TWL4030_INT_PWR_SIR 0x4 /* test register */
+#define TWL4030_INT_PWR_EDR1 0x5
+#define TWL4030_INT_PWR_EDR2 0x6
+#define TWL4030_INT_PWR_SIH_CTRL 0x7
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Accessory Interrupts
+ */
+#define TWL5031_ACIIMR_LSB 0x05
+#define TWL5031_ACIIMR_MSB 0x06
+#define TWL5031_ACIIDR_LSB 0x07
+#define TWL5031_ACIIDR_MSB 0x08
+#define TWL5031_ACCISR1 0x0F
+#define TWL5031_ACCIMR1 0x10
+#define TWL5031_ACCISR2 0x11
+#define TWL5031_ACCIMR2 0x12
+#define TWL5031_ACCSIR 0x13
+#define TWL5031_ACCEDR1 0x14
+#define TWL5031_ACCSIHCTRL 0x15
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Battery Charger Controller
+ */
+
+#define TWL5031_INTERRUPTS_BCIISR1 0x0
+#define TWL5031_INTERRUPTS_BCIIMR1 0x1
+#define TWL5031_INTERRUPTS_BCIISR2 0x2
+#define TWL5031_INTERRUPTS_BCIIMR2 0x3
+#define TWL5031_INTERRUPTS_BCISIR 0x4
+#define TWL5031_INTERRUPTS_BCIEDR1 0x5
+#define TWL5031_INTERRUPTS_BCIEDR2 0x6
+#define TWL5031_INTERRUPTS_BCISIHCTRL 0x7
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * PM Master module register offsets (use TWL4030_MODULE_PM_MASTER)
+ */
+
+#define TWL4030_PM_MASTER_CFG_P1_TRANSITION 0x00
+#define TWL4030_PM_MASTER_CFG_P2_TRANSITION 0x01
+#define TWL4030_PM_MASTER_CFG_P3_TRANSITION 0x02
+#define TWL4030_PM_MASTER_CFG_P123_TRANSITION 0x03
+#define TWL4030_PM_MASTER_STS_BOOT 0x04
+#define TWL4030_PM_MASTER_CFG_BOOT 0x05
+#define TWL4030_PM_MASTER_SHUNDAN 0x06
+#define TWL4030_PM_MASTER_BOOT_BCI 0x07
+#define TWL4030_PM_MASTER_CFG_PWRANA1 0x08
+#define TWL4030_PM_MASTER_CFG_PWRANA2 0x09
+#define TWL4030_PM_MASTER_BACKUP_MISC_STS 0x0b
+#define TWL4030_PM_MASTER_BACKUP_MISC_CFG 0x0c
+#define TWL4030_PM_MASTER_BACKUP_MISC_TST 0x0d
+#define TWL4030_PM_MASTER_PROTECT_KEY 0x0e
+#define TWL4030_PM_MASTER_STS_HW_CONDITIONS 0x0f
+#define TWL4030_PM_MASTER_P1_SW_EVENTS 0x10
+#define TWL4030_PM_MASTER_P2_SW_EVENTS 0x11
+#define TWL4030_PM_MASTER_P3_SW_EVENTS 0x12
+#define TWL4030_PM_MASTER_STS_P123_STATE 0x13
+#define TWL4030_PM_MASTER_PB_CFG 0x14
+#define TWL4030_PM_MASTER_PB_WORD_MSB 0x15
+#define TWL4030_PM_MASTER_PB_WORD_LSB 0x16
+#define TWL4030_PM_MASTER_SEQ_ADD_W2P 0x1c
+#define TWL4030_PM_MASTER_SEQ_ADD_P2A 0x1d
+#define TWL4030_PM_MASTER_SEQ_ADD_A2W 0x1e
+#define TWL4030_PM_MASTER_SEQ_ADD_A2S 0x1f
+#define TWL4030_PM_MASTER_SEQ_ADD_S2A12 0x20
+#define TWL4030_PM_MASTER_SEQ_ADD_S2A3 0x21
+#define TWL4030_PM_MASTER_SEQ_ADD_WARM 0x22
+#define TWL4030_PM_MASTER_MEMORY_ADDRESS 0x23
+#define TWL4030_PM_MASTER_MEMORY_DATA 0x24
+
+#define TWL4030_PM_MASTER_KEY_CFG1 0xc0
+#define TWL4030_PM_MASTER_KEY_CFG2 0x0c
+
+#define TWL4030_PM_MASTER_KEY_TST1 0xe0
+#define TWL4030_PM_MASTER_KEY_TST2 0x0e
+
+#define TWL4030_PM_MASTER_GLOBAL_TST 0xb6
+
+/*----------------------------------------------------------------------*/
+
+/* Power bus message definitions */
+
+/* The TWL4030/5030 splits its power-management resources (the various
+ * regulators, clock and reset lines) into 3 processor groups - P1, P2 and
+ * P3. These groups can then be configured to transition between sleep, wait-on
+ * and active states by sending messages to the power bus. See Section 5.4.2
+ * Power Resources of TWL4030 TRM
+ */
+
+/* Processor groups */
+#define DEV_GRP_NULL 0x0
+#define DEV_GRP_P1 0x1 /* P1: all OMAP devices */
+#define DEV_GRP_P2 0x2 /* P2: all Modem devices */
+#define DEV_GRP_P3 0x4 /* P3: all peripheral devices */
+
+/* Resource groups */
+#define RES_GRP_RES 0x0 /* Reserved */
+#define RES_GRP_PP 0x1 /* Power providers */
+#define RES_GRP_RC 0x2 /* Reset and control */
+#define RES_GRP_PP_RC 0x3
+#define RES_GRP_PR 0x4 /* Power references */
+#define RES_GRP_PP_PR 0x5
+#define RES_GRP_RC_PR 0x6
+#define RES_GRP_ALL 0x7 /* All resource groups */
+
+#define RES_TYPE2_R0 0x0
+
+#define RES_TYPE_ALL 0x7
+
+/* Resource states */
+#define RES_STATE_WRST 0xF
+#define RES_STATE_ACTIVE 0xE
+#define RES_STATE_SLEEP 0x8
+#define RES_STATE_OFF 0x0
+
+/* Power resources */
+
+/* Power providers */
+#define RES_VAUX1 1
+#define RES_VAUX2 2
+#define RES_VAUX3 3
+#define RES_VAUX4 4
+#define RES_VMMC1 5
+#define RES_VMMC2 6
+#define RES_VPLL1 7
+#define RES_VPLL2 8
+#define RES_VSIM 9
+#define RES_VDAC 10
+#define RES_VINTANA1 11
+#define RES_VINTANA2 12
+#define RES_VINTDIG 13
+#define RES_VIO 14
+#define RES_VDD1 15
+#define RES_VDD2 16
+#define RES_VUSB_1V5 17
+#define RES_VUSB_1V8 18
+#define RES_VUSB_3V1 19
+#define RES_VUSBCP 20
+#define RES_REGEN 21
+/* Reset and control */
+#define RES_NRES_PWRON 22
+#define RES_CLKEN 23
+#define RES_SYSEN 24
+#define RES_HFCLKOUT 25
+#define RES_32KCLKOUT 26
+#define RES_RESET 27
+/* Power Reference */
+#define RES_MAIN_REF 28
+
+#define TOTAL_RESOURCES 28
+/*
+ * Power Bus Message Format ... these can be sent individually by Linux,
+ * but are usually part of downloaded scripts that are run when various
+ * power events are triggered.
+ *
+ * Broadcast Message (16 Bits):
+ * DEV_GRP[15:13] MT[12] RES_GRP[11:9] RES_TYPE2[8:7] RES_TYPE[6:4]
+ * RES_STATE[3:0]
+ *
+ * Singular Message (16 Bits):
+ * DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0]
+ */
+
+#define MSG_BROADCAST(devgrp, grp, type, type2, state) \
+ ( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \
+ | (type) << 4 | (state))
+
+#define MSG_SINGULAR(devgrp, id, state) \
+ ((devgrp) << 13 | 0 << 12 | (id) << 4 | (state))
+
+#define MSG_BROADCAST_ALL(devgrp, state) \
+ ((devgrp) << 5 | (state))
+
+#define MSG_BROADCAST_REF MSG_BROADCAST_ALL
+#define MSG_BROADCAST_PROV MSG_BROADCAST_ALL
+#define MSG_BROADCAST__CLK_RST MSG_BROADCAST_ALL
+/*----------------------------------------------------------------------*/
+
+struct twl4030_clock_init_data {
+ bool ck32k_lowpwr_enable;
+};
+
+struct twl4030_bci_platform_data {
+ int *battery_tmp_tbl;
+ unsigned int tblsize;
+};
+
+/* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */
+struct twl4030_gpio_platform_data {
+ int gpio_base;
+ unsigned irq_base, irq_end;
+
+ /* package the two LED signals as output-only GPIOs? */
+ bool use_leds;
+
+ /* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */
+ u8 mmc_cd;
+
+ /* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */
+ u32 debounce;
+
+ /* For gpio-N, bit (1 << N) in "pullups" is set if that pullup
+ * should be enabled. Else, if that bit is set in "pulldowns",
+ * that pulldown is enabled. Don't waste power by letting any
+ * digital inputs float...
+ */
+ u32 pullups;
+ u32 pulldowns;
+
+ int (*setup)(struct device *dev,
+ unsigned gpio, unsigned ngpio);
+ int (*teardown)(struct device *dev,
+ unsigned gpio, unsigned ngpio);
+};
+
+struct twl4030_madc_platform_data {
+ int irq_line;
+};
+
+/* Boards have unique mappings of {row, col} --> keycode.
+ * Column and row are 8 bits each, but range only from 0..7.
+ * a PERSISTENT_KEY is "always on" and never reported.
+ */
+#define PERSISTENT_KEY(r, c) KEY((r), (c), KEY_RESERVED)
+
+struct twl4030_keypad_data {
+ const struct matrix_keymap_data *keymap_data;
+ unsigned rows;
+ unsigned cols;
+ bool rep;
+};
+
+enum twl4030_usb_mode {
+ T2_USB_MODE_ULPI = 1,
+ T2_USB_MODE_CEA2011_3PIN = 2,
+};
+
+struct twl4030_usb_data {
+ enum twl4030_usb_mode usb_mode;
+ unsigned long features;
+
+ int (*phy_init)(struct device *dev);
+ int (*phy_exit)(struct device *dev);
+ /* Power on/off the PHY */
+ int (*phy_power)(struct device *dev, int iD, int on);
+ /* enable/disable phy clocks */
+ int (*phy_set_clock)(struct device *dev, int on);
+ /* suspend/resume of phy */
+ int (*phy_suspend)(struct device *dev, int suspend);
+};
+
+struct twl4030_ins {
+ u16 pmb_message;
+ u8 delay;
+};
+
+struct twl4030_script {
+ struct twl4030_ins *script;
+ unsigned size;
+ u8 flags;
+#define TWL4030_WRST_SCRIPT (1<<0)
+#define TWL4030_WAKEUP12_SCRIPT (1<<1)
+#define TWL4030_WAKEUP3_SCRIPT (1<<2)
+#define TWL4030_SLEEP_SCRIPT (1<<3)
+};
+
+struct twl4030_resconfig {
+ u8 resource;
+ u8 devgroup; /* Processor group that Power resource belongs to */
+ u8 type; /* Power resource addressed, 6 / broadcast message */
+ u8 type2; /* Power resource addressed, 3 / broadcast message */
+ u8 remap_off; /* off state remapping */
+ u8 remap_sleep; /* sleep state remapping */
+};
+
+struct twl4030_power_data {
+ struct twl4030_script **scripts;
+ unsigned num;
+ struct twl4030_resconfig *resource_config;
+#define TWL4030_RESCONFIG_UNDEF ((u8)-1)
+ bool use_poweroff; /* Board is wired for TWL poweroff */
+};
+
+extern void twl4030_power_init(struct twl4030_power_data *triton2_scripts);
+extern int twl4030_remove_script(u8 flags);
+extern void twl4030_power_off(void);
+
+struct twl4030_codec_data {
+ unsigned int digimic_delay; /* in ms */
+ unsigned int ramp_delay_value;
+ unsigned int offset_cncl_path;
+ unsigned int check_defaults:1;
+ unsigned int reset_registers:1;
+ unsigned int hs_extmute:1;
+ void (*set_hs_extmute)(int mute);
+};
+
+struct twl4030_vibra_data {
+ unsigned int coexist;
+};
+
+struct twl4030_audio_data {
+ unsigned int audio_mclk;
+ struct twl4030_codec_data *codec;
+ struct twl4030_vibra_data *vibra;
+
+ /* twl6040 */
+ int audpwron_gpio; /* audio power-on gpio */
+ int naudint_irq; /* audio interrupt */
+ unsigned int irq_base;
+};
+
+struct twl4030_platform_data {
+ unsigned irq_base, irq_end;
+ struct twl4030_clock_init_data *clock;
+ struct twl4030_bci_platform_data *bci;
+ struct twl4030_gpio_platform_data *gpio;
+ struct twl4030_madc_platform_data *madc;
+ struct twl4030_keypad_data *keypad;
+ struct twl4030_usb_data *usb;
+ struct twl4030_power_data *power;
+ struct twl4030_audio_data *audio;
+
+ /* Common LDO regulators for TWL4030/TWL6030 */
+ struct regulator_init_data *vdac;
+ struct regulator_init_data *vaux1;
+ struct regulator_init_data *vaux2;
+ struct regulator_init_data *vaux3;
+ struct regulator_init_data *vdd1;
+ struct regulator_init_data *vdd2;
+ struct regulator_init_data *vdd3;
+ /* TWL4030 LDO regulators */
+ struct regulator_init_data *vpll1;
+ struct regulator_init_data *vpll2;
+ struct regulator_init_data *vmmc1;
+ struct regulator_init_data *vmmc2;
+ struct regulator_init_data *vsim;
+ struct regulator_init_data *vaux4;
+ struct regulator_init_data *vio;
+ struct regulator_init_data *vintana1;
+ struct regulator_init_data *vintana2;
+ struct regulator_init_data *vintdig;
+ /* TWL6030 LDO regulators */
+ struct regulator_init_data *vmmc;
+ struct regulator_init_data *vpp;
+ struct regulator_init_data *vusim;
+ struct regulator_init_data *vana;
+ struct regulator_init_data *vcxio;
+ struct regulator_init_data *vusb;
+ struct regulator_init_data *clk32kg;
+ struct regulator_init_data *v1v8;
+ struct regulator_init_data *v2v1;
+ /* TWL6025 LDO regulators */
+ struct regulator_init_data *ldo1;
+ struct regulator_init_data *ldo2;
+ struct regulator_init_data *ldo3;
+ struct regulator_init_data *ldo4;
+ struct regulator_init_data *ldo5;
+ struct regulator_init_data *ldo6;
+ struct regulator_init_data *ldo7;
+ struct regulator_init_data *ldoln;
+ struct regulator_init_data *ldousb;
+ /* TWL6025 DCDC regulators */
+ struct regulator_init_data *smps3;
+ struct regulator_init_data *smps4;
+ struct regulator_init_data *vio6025;
+};
+
+struct twl_regulator_driver_data {
+ int (*set_voltage)(void *data, int target_uV);
+ int (*get_voltage)(void *data);
+ void *data;
+ unsigned long features;
+};
+
+/*----------------------------------------------------------------------*/
+
+int twl4030_sih_setup(struct device *dev, int module, int irq_base);
+
+/* Offsets to Power Registers */
+#define TWL4030_VDAC_DEV_GRP 0x3B
+#define TWL4030_VDAC_DEDICATED 0x3E
+#define TWL4030_VAUX1_DEV_GRP 0x17
+#define TWL4030_VAUX1_DEDICATED 0x1A
+#define TWL4030_VAUX2_DEV_GRP 0x1B
+#define TWL4030_VAUX2_DEDICATED 0x1E
+#define TWL4030_VAUX3_DEV_GRP 0x1F
+#define TWL4030_VAUX3_DEDICATED 0x22
+
+static inline int twl4030charger_usb_en(int enable) { return 0; }
+
+/*----------------------------------------------------------------------*/
+
+/* Linux-specific regulator identifiers ... for now, we only support
+ * the LDOs, and leave the three buck converters alone. VDD1 and VDD2
+ * need to tie into hardware based voltage scaling (cpufreq etc), while
+ * VIO is generally fixed.
+ */
+
+/* TWL4030 SMPS/LDO's */
+/* EXTERNAL dc-to-dc buck converters */
+#define TWL4030_REG_VDD1 0
+#define TWL4030_REG_VDD2 1
+#define TWL4030_REG_VIO 2
+
+/* EXTERNAL LDOs */
+#define TWL4030_REG_VDAC 3
+#define TWL4030_REG_VPLL1 4
+#define TWL4030_REG_VPLL2 5 /* not on all chips */
+#define TWL4030_REG_VMMC1 6
+#define TWL4030_REG_VMMC2 7 /* not on all chips */
+#define TWL4030_REG_VSIM 8 /* not on all chips */
+#define TWL4030_REG_VAUX1 9 /* not on all chips */
+#define TWL4030_REG_VAUX2_4030 10 /* (twl4030-specific) */
+#define TWL4030_REG_VAUX2 11 /* (twl5030 and newer) */
+#define TWL4030_REG_VAUX3 12 /* not on all chips */
+#define TWL4030_REG_VAUX4 13 /* not on all chips */
+
+/* INTERNAL LDOs */
+#define TWL4030_REG_VINTANA1 14
+#define TWL4030_REG_VINTANA2 15
+#define TWL4030_REG_VINTDIG 16
+#define TWL4030_REG_VUSB1V5 17
+#define TWL4030_REG_VUSB1V8 18
+#define TWL4030_REG_VUSB3V1 19
+
+/* TWL6030 SMPS/LDO's */
+/* EXTERNAL dc-to-dc buck convertor controllable via SR */
+#define TWL6030_REG_VDD1 30
+#define TWL6030_REG_VDD2 31
+#define TWL6030_REG_VDD3 32
+
+/* Non SR compliant dc-to-dc buck convertors */
+#define TWL6030_REG_VMEM 33
+#define TWL6030_REG_V2V1 34
+#define TWL6030_REG_V1V29 35
+#define TWL6030_REG_V1V8 36
+
+/* EXTERNAL LDOs */
+#define TWL6030_REG_VAUX1_6030 37
+#define TWL6030_REG_VAUX2_6030 38
+#define TWL6030_REG_VAUX3_6030 39
+#define TWL6030_REG_VMMC 40
+#define TWL6030_REG_VPP 41
+#define TWL6030_REG_VUSIM 42
+#define TWL6030_REG_VANA 43
+#define TWL6030_REG_VCXIO 44
+#define TWL6030_REG_VDAC 45
+#define TWL6030_REG_VUSB 46
+
+/* INTERNAL LDOs */
+#define TWL6030_REG_VRTC 47
+#define TWL6030_REG_CLK32KG 48
+
+/* LDOs on 6025 have different names */
+#define TWL6025_REG_LDO2 49
+#define TWL6025_REG_LDO4 50
+#define TWL6025_REG_LDO3 51
+#define TWL6025_REG_LDO5 52
+#define TWL6025_REG_LDO1 53
+#define TWL6025_REG_LDO7 54
+#define TWL6025_REG_LDO6 55
+#define TWL6025_REG_LDOLN 56
+#define TWL6025_REG_LDOUSB 57
+
+/* 6025 DCDC supplies */
+#define TWL6025_REG_SMPS3 58
+#define TWL6025_REG_SMPS4 59
+#define TWL6025_REG_VIO 60
+
+
+#endif /* End of __TWL4030_H */
diff --git a/include/linux/i2c/twl4030-madc.h b/include/linux/i2c/twl4030-madc.h
new file mode 100644
index 0000000..530e11b
--- /dev/null
+++ b/include/linux/i2c/twl4030-madc.h
@@ -0,0 +1,145 @@
+/*
+ * twl4030_madc.h - Header for TWL4030 MADC
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * J Keerthy <j-keerthy@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef _TWL4030_MADC_H
+#define _TWL4030_MADC_H
+
+struct twl4030_madc_conversion_method {
+ u8 sel;
+ u8 avg;
+ u8 rbase;
+ u8 ctrl;
+};
+
+#define TWL4030_MADC_MAX_CHANNELS 16
+
+
+/*
+ * twl4030_madc_request- madc request packet for channel conversion
+ * @channels: 16 bit bitmap for individual channels
+ * @do_avgP: sample the input channel for 4 consecutive cycles
+ * @method: RT, SW1, SW2
+ * @type: Polling or interrupt based method
+ */
+
+struct twl4030_madc_request {
+ unsigned long channels;
+ u16 do_avg;
+ u16 method;
+ u16 type;
+ bool active;
+ bool result_pending;
+ int rbuf[TWL4030_MADC_MAX_CHANNELS];
+ void (*func_cb)(int len, int channels, int *buf);
+};
+
+enum conversion_methods {
+ TWL4030_MADC_RT,
+ TWL4030_MADC_SW1,
+ TWL4030_MADC_SW2,
+ TWL4030_MADC_NUM_METHODS
+};
+
+enum sample_type {
+ TWL4030_MADC_WAIT,
+ TWL4030_MADC_IRQ_ONESHOT,
+ TWL4030_MADC_IRQ_REARM
+};
+
+#define TWL4030_MADC_CTRL1 0x00
+#define TWL4030_MADC_CTRL2 0x01
+
+#define TWL4030_MADC_RTSELECT_LSB 0x02
+#define TWL4030_MADC_SW1SELECT_LSB 0x06
+#define TWL4030_MADC_SW2SELECT_LSB 0x0A
+
+#define TWL4030_MADC_RTAVERAGE_LSB 0x04
+#define TWL4030_MADC_SW1AVERAGE_LSB 0x08
+#define TWL4030_MADC_SW2AVERAGE_LSB 0x0C
+
+#define TWL4030_MADC_CTRL_SW1 0x12
+#define TWL4030_MADC_CTRL_SW2 0x13
+
+#define TWL4030_MADC_RTCH0_LSB 0x17
+#define TWL4030_MADC_GPCH0_LSB 0x37
+
+#define TWL4030_MADC_MADCON (1 << 0) /* MADC power on */
+#define TWL4030_MADC_BUSY (1 << 0) /* MADC busy */
+/* MADC conversion completion */
+#define TWL4030_MADC_EOC_SW (1 << 1)
+/* MADC SWx start conversion */
+#define TWL4030_MADC_SW_START (1 << 5)
+#define TWL4030_MADC_ADCIN0 (1 << 0)
+#define TWL4030_MADC_ADCIN1 (1 << 1)
+#define TWL4030_MADC_ADCIN2 (1 << 2)
+#define TWL4030_MADC_ADCIN3 (1 << 3)
+#define TWL4030_MADC_ADCIN4 (1 << 4)
+#define TWL4030_MADC_ADCIN5 (1 << 5)
+#define TWL4030_MADC_ADCIN6 (1 << 6)
+#define TWL4030_MADC_ADCIN7 (1 << 7)
+#define TWL4030_MADC_ADCIN8 (1 << 8)
+#define TWL4030_MADC_ADCIN9 (1 << 9)
+#define TWL4030_MADC_ADCIN10 (1 << 10)
+#define TWL4030_MADC_ADCIN11 (1 << 11)
+#define TWL4030_MADC_ADCIN12 (1 << 12)
+#define TWL4030_MADC_ADCIN13 (1 << 13)
+#define TWL4030_MADC_ADCIN14 (1 << 14)
+#define TWL4030_MADC_ADCIN15 (1 << 15)
+
+/* Fixed channels */
+#define TWL4030_MADC_BTEMP TWL4030_MADC_ADCIN1
+#define TWL4030_MADC_VBUS TWL4030_MADC_ADCIN8
+#define TWL4030_MADC_VBKB TWL4030_MADC_ADCIN9
+#define TWL4030_MADC_ICHG TWL4030_MADC_ADCIN10
+#define TWL4030_MADC_VCHG TWL4030_MADC_ADCIN11
+#define TWL4030_MADC_VBAT TWL4030_MADC_ADCIN12
+
+/* Step size and prescaler ratio */
+#define TEMP_STEP_SIZE 147
+#define TEMP_PSR_R 100
+#define CURR_STEP_SIZE 147
+#define CURR_PSR_R1 44
+#define CURR_PSR_R2 88
+
+#define TWL4030_BCI_BCICTL1 0x23
+#define TWL4030_BCI_CGAIN 0x020
+#define TWL4030_BCI_MESBAT (1 << 1)
+#define TWL4030_BCI_TYPEN (1 << 4)
+#define TWL4030_BCI_ITHEN (1 << 3)
+
+#define REG_BCICTL2 0x024
+#define TWL4030_BCI_ITHSENS 0x007
+
+/* Register and bits for GPBR1 register */
+#define TWL4030_REG_GPBR1 0x0c
+#define TWL4030_GPBR1_MADC_HFCLK_EN (1 << 7)
+
+struct twl4030_madc_user_parms {
+ int channel;
+ int average;
+ int status;
+ u16 result;
+};
+
+int twl4030_madc_conversion(struct twl4030_madc_request *conv);
+int twl4030_get_madc_conversion(int channel_no);
+#endif