Initial commit from HTC m7ul-3.4.10-jb-crc-ddcfb8c
diff --git a/include/linux/i2c/dm355evm_msp.h b/include/linux/i2c/dm355evm_msp.h
new file mode 100644
index 0000000..3724703
--- /dev/null
+++ b/include/linux/i2c/dm355evm_msp.h
@@ -0,0 +1,79 @@
+/*
+ * dm355evm_msp.h - support MSP430 microcontroller on DM355EVM board
+ */
+#ifndef __LINUX_I2C_DM355EVM_MSP
+#define __LINUX_I2C_DM355EVM_MSP
+
+/*
+ * Written against Spectrum's writeup for the A4 firmware revision,
+ * and tweaked to match source and rev D2 schematics by removing CPLD
+ * and NOR flash hooks (which were last appropriate in rev B boards).
+ *
+ * Note that the firmware supports a flavor of write posting ... to be
+ * sure a write completes, issue another read or write.
+ */
+
+/* utilities to access "registers" emulated by msp430 firmware */
+extern int dm355evm_msp_write(u8 value, u8 reg);
+extern int dm355evm_msp_read(u8 reg);
+
+
+/* command/control registers */
+#define DM355EVM_MSP_COMMAND 0x00
+# define MSP_COMMAND_NULL 0
+# define MSP_COMMAND_RESET_COLD 1
+# define MSP_COMMAND_RESET_WARM 2
+# define MSP_COMMAND_RESET_WARM_I 3
+# define MSP_COMMAND_POWEROFF 4
+# define MSP_COMMAND_IR_REINIT 5
+#define DM355EVM_MSP_STATUS 0x01
+# define MSP_STATUS_BAD_OFFSET BIT(0)
+# define MSP_STATUS_BAD_COMMAND BIT(1)
+# define MSP_STATUS_POWER_ERROR BIT(2)
+# define MSP_STATUS_RXBUF_OVERRUN BIT(3)
+#define DM355EVM_MSP_RESET 0x02 /* 0 bits == in reset */
+# define MSP_RESET_DC5 BIT(0)
+# define MSP_RESET_TVP5154 BIT(2)
+# define MSP_RESET_IMAGER BIT(3)
+# define MSP_RESET_ETHERNET BIT(4)
+# define MSP_RESET_SYS BIT(5)
+# define MSP_RESET_AIC33 BIT(7)
+
+/* GPIO registers ... bit patterns mostly match the source MSP ports */
+#define DM355EVM_MSP_LED 0x03 /* active low (MSP P4) */
+#define DM355EVM_MSP_SWITCH1 0x04 /* (MSP P5, masked) */
+# define MSP_SWITCH1_SW6_1 BIT(0)
+# define MSP_SWITCH1_SW6_2 BIT(1)
+# define MSP_SWITCH1_SW6_3 BIT(2)
+# define MSP_SWITCH1_SW6_4 BIT(3)
+# define MSP_SWITCH1_J1 BIT(4) /* NTSC/PAL */
+# define MSP_SWITCH1_MSP_INT BIT(5) /* active low */
+#define DM355EVM_MSP_SWITCH2 0x05 /* (MSP P6, masked) */
+# define MSP_SWITCH2_SW10 BIT(3)
+# define MSP_SWITCH2_SW11 BIT(4)
+# define MSP_SWITCH2_SW12 BIT(5)
+# define MSP_SWITCH2_SW13 BIT(6)
+# define MSP_SWITCH2_SW14 BIT(7)
+#define DM355EVM_MSP_SDMMC 0x06 /* (MSP P2, masked) */
+# define MSP_SDMMC_0_WP BIT(1)
+# define MSP_SDMMC_0_CD BIT(2) /* active low */
+# define MSP_SDMMC_1_WP BIT(3)
+# define MSP_SDMMC_1_CD BIT(4) /* active low */
+#define DM355EVM_MSP_FIRMREV 0x07 /* not a GPIO (out of order) */
+#define DM355EVM_MSP_VIDEO_IN 0x08 /* (MSP P3, masked) */
+# define MSP_VIDEO_IMAGER BIT(7) /* low == tvp5146 */
+
+/* power supply registers are currently omitted */
+
+/* RTC registers */
+#define DM355EVM_MSP_RTC_0 0x12 /* LSB */
+#define DM355EVM_MSP_RTC_1 0x13
+#define DM355EVM_MSP_RTC_2 0x14
+#define DM355EVM_MSP_RTC_3 0x15 /* MSB */
+
+/* input event queue registers; code == ((HIGH << 8) | LOW) */
+#define DM355EVM_MSP_INPUT_COUNT 0x16 /* decrement by reading LOW */
+#define DM355EVM_MSP_INPUT_HIGH 0x17
+#define DM355EVM_MSP_INPUT_LOW 0x18
+
+#endif /* __LINUX_I2C_DM355EVM_MSP */