ixgbe: add device support for 82598AT (copper 10GbE) adapters
Intel is currently shipping support for adapters with a phy
that does 10GBase-T (copper), which is 10 Gigabit ethernet
over standard Category 6 cabling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index 028bfb2..2a12e97 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -68,6 +68,8 @@
board_82598 },
{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82598AF_SINGLE_PORT),
board_82598 },
+ {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82598AT),
+ board_82598 },
{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82598EB_CX4),
board_82598 },
{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82598_CX4_DUAL_PORT),
@@ -904,6 +906,17 @@
return;
}
+static void ixgbe_check_fan_failure(struct ixgbe_adapter *adapter, u32 eicr)
+{
+ struct ixgbe_hw *hw = &adapter->hw;
+
+ if ((adapter->flags & IXGBE_FLAG_FAN_FAIL_CAPABLE) &&
+ (eicr & IXGBE_EICR_GPI_SDP1)) {
+ DPRINTK(PROBE, CRIT, "Fan has stopped, replace the adapter\n");
+ /* write to clear the interrupt */
+ IXGBE_WRITE_REG(hw, IXGBE_EICR, IXGBE_EICR_GPI_SDP1);
+ }
+}
static void ixgbe_check_lsc(struct ixgbe_adapter *adapter)
{
@@ -928,6 +941,8 @@
if (eicr & IXGBE_EICR_LSC)
ixgbe_check_lsc(adapter);
+ ixgbe_check_fan_failure(adapter, eicr);
+
if (!test_bit(__IXGBE_DOWN, &adapter->state))
IXGBE_WRITE_REG(hw, IXGBE_EIMS, IXGBE_EIMS_OTHER);
@@ -1316,6 +1331,8 @@
if (eicr & IXGBE_EICR_LSC)
ixgbe_check_lsc(adapter);
+ ixgbe_check_fan_failure(adapter, eicr);
+
if (netif_rx_schedule_prep(netdev, &adapter->q_vector[0].napi)) {
adapter->tx_ring[0].total_packets = 0;
adapter->tx_ring[0].total_bytes = 0;
@@ -1418,6 +1435,8 @@
{
u32 mask;
mask = IXGBE_EIMS_ENABLE_MASK;
+ if (adapter->flags & IXGBE_FLAG_FAN_FAIL_CAPABLE)
+ mask |= IXGBE_EIMS_GPI_SDP1;
IXGBE_WRITE_REG(&adapter->hw, IXGBE_EIMS, mask);
IXGBE_WRITE_FLUSH(&adapter->hw);
}
@@ -1927,6 +1946,13 @@
IXGBE_WRITE_REG(hw, IXGBE_EIAM, IXGBE_EICS_RTX_QUEUE);
}
+ /* Enable fan failure interrupt if media type is copper */
+ if (adapter->flags & IXGBE_FLAG_FAN_FAIL_CAPABLE) {
+ gpie = IXGBE_READ_REG(hw, IXGBE_GPIE);
+ gpie |= IXGBE_SDP1_GPIEN;
+ IXGBE_WRITE_REG(hw, IXGBE_GPIE, gpie);
+ }
+
mhadd = IXGBE_READ_REG(hw, IXGBE_MHADD);
if (max_frame != (mhadd >> IXGBE_MHADD_MFS_SHIFT)) {
mhadd &= ~IXGBE_MHADD_MFS_MASK;
@@ -2564,6 +2590,9 @@
rss = min(IXGBE_MAX_RSS_INDICES, (int)num_online_cpus());
adapter->ring_feature[RING_F_RSS].indices = rss;
adapter->flags |= IXGBE_FLAG_RSS_ENABLED;
+ if (hw->mac.ops.get_media_type &&
+ (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_copper))
+ adapter->flags |= IXGBE_FLAG_FAN_FAIL_CAPABLE;
/* default flow control settings */
hw->fc.original_type = ixgbe_fc_none;
@@ -3691,6 +3720,10 @@
/* must always autoneg for both 1G and 10G link */
hw->mac.autoneg = true;
+ if ((hw->mac.type == ixgbe_mac_82598EB) &&
+ (hw->phy.media_type == ixgbe_media_type_copper))
+ autoneg = IXGBE_LINK_SPEED_82598_AUTONEG;
+
return hw->mac.ops.setup_link_speed(hw, autoneg, true, true);
}