Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/arch/frv/kernel/gdb-io.h b/arch/frv/kernel/gdb-io.h
new file mode 100644
index 0000000..138714b
--- /dev/null
+++ b/arch/frv/kernel/gdb-io.h
@@ -0,0 +1,55 @@
+/* gdb-io.h: FR403 GDB I/O port defs
+ *
+ * Copyright (C) 2003 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#ifndef _GDB_IO_H
+#define _GDB_IO_H
+
+#include <asm/serial-regs.h>
+
+#undef UART_RX
+#undef UART_TX
+#undef UART_DLL
+#undef UART_DLM
+#undef UART_IER
+#undef UART_IIR
+#undef UART_FCR
+#undef UART_LCR
+#undef UART_MCR
+#undef UART_LSR
+#undef UART_MSR
+#undef UART_SCR
+
+#define UART_RX 0*8 /* In: Receive buffer (DLAB=0) */
+#define UART_TX 0*8 /* Out: Transmit buffer (DLAB=0) */
+#define UART_DLL 0*8 /* Out: Divisor Latch Low (DLAB=1) */
+#define UART_DLM 1*8 /* Out: Divisor Latch High (DLAB=1) */
+#define UART_IER 1*8 /* Out: Interrupt Enable Register */
+#define UART_IIR 2*8 /* In: Interrupt ID Register */
+#define UART_FCR 2*8 /* Out: FIFO Control Register */
+#define UART_LCR 3*8 /* Out: Line Control Register */
+#define UART_MCR 4*8 /* Out: Modem Control Register */
+#define UART_LSR 5*8 /* In: Line Status Register */
+#define UART_MSR 6*8 /* In: Modem Status Register */
+#define UART_SCR 7*8 /* I/O: Scratch Register */
+
+#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
+#define UART_LCR_SBC 0x40 /* Set break control */
+#define UART_LCR_SPAR 0x20 /* Stick parity (?) */
+#define UART_LCR_EPAR 0x10 /* Even parity select */
+#define UART_LCR_PARITY 0x08 /* Parity Enable */
+#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
+#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */
+#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */
+#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */
+#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */
+
+
+#endif /* _GDB_IO_H */