Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/include/media/audiochip.h b/include/media/audiochip.h
new file mode 100644
index 0000000..d3e9e30
--- /dev/null
+++ b/include/media/audiochip.h
@@ -0,0 +1,35 @@
+#ifndef AUDIOCHIP_H
+#define AUDIOCHIP_H
+
+/* ---------------------------------------------------------------------- */
+
+/* v4l device was opened in Radio mode */
+#define AUDC_SET_RADIO _IO('m',2)
+/* select from TV,radio,extern,MUTE */
+#define AUDC_SET_INPUT _IOW('m',17,int)
+
+/* audio inputs */
+#define AUDIO_TUNER 0x00
+#define AUDIO_RADIO 0x01
+#define AUDIO_EXTERN 0x02
+#define AUDIO_INTERN 0x03
+#define AUDIO_OFF 0x04
+#define AUDIO_ON 0x05
+#define AUDIO_EXTERN_1 AUDIO_EXTERN
+#define AUDIO_EXTERN_2 0x06
+#define AUDIO_MUTE 0x80
+#define AUDIO_UNMUTE 0x81
+
+/* all the stuff below is obsolete and just here for reference. I'll
+ * remove it once the driver is tested and works fine.
+ *
+ * Instead creating alot of tiny API's for all kinds of different
+ * chips, we'll just pass throuth the v4l ioctl structs (v4l2 not
+ * yet...). It is a bit less flexible, but most/all used i2c chips
+ * make sense in v4l context only. So I think that's acceptable...
+ */
+
+/* misc stuff to pass around config info to i2c chips */
+#define AUDC_CONFIG_PINNACLE _IOW('m',32,int)
+
+#endif /* AUDIOCHIP_H */
diff --git a/include/media/id.h b/include/media/id.h
new file mode 100644
index 0000000..1b0320d
--- /dev/null
+++ b/include/media/id.h
@@ -0,0 +1,37 @@
+/* FIXME: this temporarely, until these are included in linux/i2c-id.h */
+
+/* drivers */
+#ifndef I2C_DRIVERID_TVMIXER
+# define I2C_DRIVERID_TVMIXER I2C_DRIVERID_EXP0
+#endif
+#ifndef I2C_DRIVERID_TVAUDIO
+# define I2C_DRIVERID_TVAUDIO I2C_DRIVERID_EXP1
+#endif
+
+/* chips */
+#ifndef I2C_DRIVERID_DPL3518
+# define I2C_DRIVERID_DPL3518 I2C_DRIVERID_EXP2
+#endif
+#ifndef I2C_DRIVERID_TDA9873
+# define I2C_DRIVERID_TDA9873 I2C_DRIVERID_EXP3
+#endif
+#ifndef I2C_DRIVERID_TDA9875
+# define I2C_DRIVERID_TDA9875 I2C_DRIVERID_EXP0+4
+#endif
+#ifndef I2C_DRIVERID_PIC16C54_PV951
+# define I2C_DRIVERID_PIC16C54_PV951 I2C_DRIVERID_EXP0+5
+#endif
+#ifndef I2C_DRIVERID_TDA7432
+# define I2C_DRIVERID_TDA7432 I2C_DRIVERID_EXP0+6
+#endif
+#ifndef I2C_DRIVERID_TDA9874
+# define I2C_DRIVERID_TDA9874 I2C_DRIVERID_EXP0+7
+#endif
+#ifndef I2C_DRIVERID_SAA6752HS
+# define I2C_DRIVERID_SAA6752HS I2C_DRIVERID_EXP0+8
+#endif
+
+/* algorithms */
+#ifndef I2C_ALGO_SAA7134
+# define I2C_ALGO_SAA7134 0x090000
+#endif
diff --git a/include/media/ir-common.h b/include/media/ir-common.h
new file mode 100644
index 0000000..62c963a
--- /dev/null
+++ b/include/media/ir-common.h
@@ -0,0 +1,67 @@
+/*
+ * $Id: ir-common.h,v 1.8 2005/02/22 12:28:40 kraxel Exp $
+ *
+ * some common structs and functions to handle infrared remotes via
+ * input layer ...
+ *
+ * (c) 2003 Gerd Knorr <kraxel@bytesex.org> [SuSE Labs]
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/version.h>
+#include <linux/input.h>
+
+
+#define IR_TYPE_RC5 1
+#define IR_TYPE_OTHER 99
+
+#define IR_KEYTAB_TYPE u32
+#define IR_KEYTAB_SIZE 128 // enougth for rc5, probably need more some day ...
+
+#define IR_KEYCODE(tab,code) (((unsigned)code < IR_KEYTAB_SIZE) \
+ ? tab[code] : KEY_RESERVED)
+
+struct ir_input_state {
+ /* configuration */
+ int ir_type;
+ IR_KEYTAB_TYPE ir_codes[IR_KEYTAB_SIZE];
+
+ /* key info */
+ u32 ir_raw; /* raw data */
+ u32 ir_key; /* ir key code */
+ u32 keycode; /* linux key code */
+ int keypressed; /* current state */
+};
+
+extern IR_KEYTAB_TYPE ir_codes_rc5_tv[IR_KEYTAB_SIZE];
+extern IR_KEYTAB_TYPE ir_codes_winfast[IR_KEYTAB_SIZE];
+extern IR_KEYTAB_TYPE ir_codes_empty[IR_KEYTAB_SIZE];
+extern IR_KEYTAB_TYPE ir_codes_hauppauge_new[IR_KEYTAB_SIZE];
+
+void ir_input_init(struct input_dev *dev, struct ir_input_state *ir,
+ int ir_type, IR_KEYTAB_TYPE *ir_codes);
+void ir_input_nokey(struct input_dev *dev, struct ir_input_state *ir);
+void ir_input_keydown(struct input_dev *dev, struct ir_input_state *ir,
+ u32 ir_key, u32 ir_raw);
+u32 ir_extract_bits(u32 data, u32 mask);
+int ir_dump_samples(u32 *samples, int count);
+int ir_decode_biphase(u32 *samples, int count, int low, int high);
+
+/*
+ * Local variables:
+ * c-basic-offset: 8
+ * End:
+ */
diff --git a/include/media/ovcamchip.h b/include/media/ovcamchip.h
new file mode 100644
index 0000000..cb7c0aa
--- /dev/null
+++ b/include/media/ovcamchip.h
@@ -0,0 +1,104 @@
+/* OmniVision* camera chip driver API
+ *
+ * Copyright (c) 1999-2004 Mark McClelland
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version. NO WARRANTY OF ANY KIND is expressed or implied.
+ *
+ * * OmniVision is a trademark of OmniVision Technologies, Inc. This driver
+ * is not sponsored or developed by them.
+ */
+
+#ifndef __LINUX_OVCAMCHIP_H
+#define __LINUX_OVCAMCHIP_H
+
+#include <linux/videodev.h>
+#include <linux/i2c.h>
+
+/* Remove these once they are officially defined */
+#ifndef I2C_DRIVERID_OVCAMCHIP
+ #define I2C_DRIVERID_OVCAMCHIP 0xf00f
+#endif
+#ifndef I2C_HW_SMBUS_OV511
+ #define I2C_HW_SMBUS_OV511 0xfe
+#endif
+#ifndef I2C_HW_SMBUS_OV518
+ #define I2C_HW_SMBUS_OV518 0xff
+#endif
+#ifndef I2C_HW_SMBUS_OVFX2
+ #define I2C_HW_SMBUS_OVFX2 0xfd
+#endif
+
+/* --------------------------------- */
+/* ENUMERATIONS */
+/* --------------------------------- */
+
+/* Controls */
+enum {
+ OVCAMCHIP_CID_CONT, /* Contrast */
+ OVCAMCHIP_CID_BRIGHT, /* Brightness */
+ OVCAMCHIP_CID_SAT, /* Saturation */
+ OVCAMCHIP_CID_HUE, /* Hue */
+ OVCAMCHIP_CID_EXP, /* Exposure */
+ OVCAMCHIP_CID_FREQ, /* Light frequency */
+ OVCAMCHIP_CID_BANDFILT, /* Banding filter */
+ OVCAMCHIP_CID_AUTOBRIGHT, /* Auto brightness */
+ OVCAMCHIP_CID_AUTOEXP, /* Auto exposure */
+ OVCAMCHIP_CID_BACKLIGHT, /* Back light compensation */
+ OVCAMCHIP_CID_MIRROR, /* Mirror horizontally */
+};
+
+/* Chip types */
+#define NUM_CC_TYPES 9
+enum {
+ CC_UNKNOWN,
+ CC_OV76BE,
+ CC_OV7610,
+ CC_OV7620,
+ CC_OV7620AE,
+ CC_OV6620,
+ CC_OV6630,
+ CC_OV6630AE,
+ CC_OV6630AF,
+};
+
+/* --------------------------------- */
+/* I2C ADDRESSES */
+/* --------------------------------- */
+
+#define OV7xx0_SID (0x42 >> 1)
+#define OV6xx0_SID (0xC0 >> 1)
+
+/* --------------------------------- */
+/* API */
+/* --------------------------------- */
+
+struct ovcamchip_control {
+ __u32 id;
+ __s32 value;
+};
+
+struct ovcamchip_window {
+ int x;
+ int y;
+ int width;
+ int height;
+ int format;
+ int quarter; /* Scale width and height down 2x */
+
+ /* This stuff will be removed eventually */
+ int clockdiv; /* Clock divisor setting */
+};
+
+/* Commands */
+#define OVCAMCHIP_CMD_Q_SUBTYPE _IOR (0x88, 0x00, int)
+#define OVCAMCHIP_CMD_INITIALIZE _IOW (0x88, 0x01, int)
+/* You must call OVCAMCHIP_CMD_INITIALIZE before any of commands below! */
+#define OVCAMCHIP_CMD_S_CTRL _IOW (0x88, 0x02, struct ovcamchip_control)
+#define OVCAMCHIP_CMD_G_CTRL _IOWR (0x88, 0x03, struct ovcamchip_control)
+#define OVCAMCHIP_CMD_S_MODE _IOW (0x88, 0x04, struct ovcamchip_window)
+#define OVCAMCHIP_MAX_CMD _IO (0x88, 0x3f)
+
+#endif
diff --git a/include/media/saa6752hs.h b/include/media/saa6752hs.h
new file mode 100644
index 0000000..791bad2
--- /dev/null
+++ b/include/media/saa6752hs.h
@@ -0,0 +1,75 @@
+/*
+ saa6752hs.h - definition for saa6752hs MPEG encoder
+
+ Copyright (C) 2003 Andrew de Quincey <adq@lidskialf.net>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+
+#if 0 /* ndef _SAA6752HS_H */
+#define _SAA6752HS_H
+
+enum mpeg_video_bitrate_mode {
+ MPEG_VIDEO_BITRATE_MODE_VBR = 0, /* Variable bitrate */
+ MPEG_VIDEO_BITRATE_MODE_CBR = 1, /* Constant bitrate */
+
+ MPEG_VIDEO_BITRATE_MODE_MAX
+};
+
+enum mpeg_audio_bitrate {
+ MPEG_AUDIO_BITRATE_256 = 0, /* 256 kBit/sec */
+ MPEG_AUDIO_BITRATE_384 = 1, /* 384 kBit/sec */
+
+ MPEG_AUDIO_BITRATE_MAX
+};
+
+enum mpeg_video_format {
+ MPEG_VIDEO_FORMAT_D1 = 0,
+ MPEG_VIDEO_FORMAT_2_3_D1 = 1,
+ MPEG_VIDEO_FORMAT_1_2_D1 = 2,
+ MPEG_VIDEO_FORMAT_SIF = 3,
+
+ MPEG_VIDEO_FORMAT_MAX
+};
+
+#define MPEG_VIDEO_TARGET_BITRATE_MAX 27000
+#define MPEG_VIDEO_MAX_BITRATE_MAX 27000
+#define MPEG_TOTAL_BITRATE_MAX 27000
+#define MPEG_PID_MAX ((1 << 14) - 1)
+
+struct mpeg_params {
+ enum mpeg_video_bitrate_mode video_bitrate_mode;
+ unsigned int video_target_bitrate;
+ unsigned int video_max_bitrate; // only used for VBR
+ enum mpeg_audio_bitrate audio_bitrate;
+ unsigned int total_bitrate;
+
+ unsigned int pmt_pid;
+ unsigned int video_pid;
+ unsigned int audio_pid;
+ unsigned int pcr_pid;
+
+ enum mpeg_video_format video_format;
+};
+
+#define MPEG_SETPARAMS _IOW('6',100,struct mpeg_params)
+
+#endif // _SAA6752HS_H
+
+/*
+ * Local variables:
+ * c-basic-offset: 8
+ * End:
+ */
diff --git a/include/media/saa7146.h b/include/media/saa7146.h
new file mode 100644
index 0000000..3dfb8d6
--- /dev/null
+++ b/include/media/saa7146.h
@@ -0,0 +1,452 @@
+#ifndef __SAA7146__
+#define __SAA7146__
+
+#include <linux/version.h> /* for version macros */
+#include <linux/module.h> /* for module-version */
+#include <linux/delay.h> /* for delay-stuff */
+#include <linux/slab.h> /* for kmalloc/kfree */
+#include <linux/pci.h> /* for pci-config-stuff, vendor ids etc. */
+#include <linux/init.h> /* for "__init" */
+#include <linux/interrupt.h> /* for IMMEDIATE_BH */
+#include <linux/kmod.h> /* for kernel module loader */
+#include <linux/i2c.h> /* for i2c subsystem */
+#include <asm/io.h> /* for accessing devices */
+#include <linux/stringify.h>
+#include <linux/vmalloc.h> /* for vmalloc() */
+#include <linux/mm.h> /* for vmalloc_to_page() */
+
+/* ugly, but necessary to build the dvb stuff under 2.4. */
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,51)
+ #include "dvb_functions.h"
+#endif
+
+#define SAA7146_VERSION_CODE KERNEL_VERSION(0,5,0)
+
+#define saa7146_write(sxy,adr,dat) writel((dat),(sxy->mem+(adr)))
+#define saa7146_read(sxy,adr) readl(sxy->mem+(adr))
+
+extern unsigned int saa7146_debug;
+
+//#define DEBUG_PROLOG printk("(0x%08x)(0x%08x) %s: %s(): ",(dev==0?-1:(dev->mem==0?-1:saa7146_read(dev,RPS_ADDR0))),(dev==0?-1:(dev->mem==0?-1:saa7146_read(dev,IER))),__stringify(KBUILD_MODNAME),__FUNCTION__)
+
+#ifndef DEBUG_VARIABLE
+ #define DEBUG_VARIABLE saa7146_debug
+#endif
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,51)
+#define DEBUG_PROLOG printk("%s: %s(): ",__stringify(KBUILD_BASENAME),__FUNCTION__)
+#define INFO(x) { printk("%s: ",__stringify(KBUILD_BASENAME)); printk x; }
+#else
+#define DEBUG_PROLOG printk("%s: %s(): ",__stringify(KBUILD_MODNAME),__FUNCTION__)
+#define INFO(x) { printk("%s: ",__stringify(KBUILD_MODNAME)); printk x; }
+#endif
+
+#define ERR(x) { DEBUG_PROLOG; printk x; }
+
+#define DEB_S(x) if (0!=(DEBUG_VARIABLE&0x01)) { DEBUG_PROLOG; printk x; } /* simple debug messages */
+#define DEB_D(x) if (0!=(DEBUG_VARIABLE&0x02)) { DEBUG_PROLOG; printk x; } /* more detailed debug messages */
+#define DEB_EE(x) if (0!=(DEBUG_VARIABLE&0x04)) { DEBUG_PROLOG; printk x; } /* print enter and exit of functions */
+#define DEB_I2C(x) if (0!=(DEBUG_VARIABLE&0x08)) { DEBUG_PROLOG; printk x; } /* i2c debug messages */
+#define DEB_VBI(x) if (0!=(DEBUG_VARIABLE&0x10)) { DEBUG_PROLOG; printk x; } /* vbi debug messages */
+#define DEB_INT(x) if (0!=(DEBUG_VARIABLE&0x20)) { DEBUG_PROLOG; printk x; } /* interrupt debug messages */
+#define DEB_CAP(x) if (0!=(DEBUG_VARIABLE&0x40)) { DEBUG_PROLOG; printk x; } /* capture debug messages */
+
+#define SAA7146_IER_DISABLE(x,y) \
+ saa7146_write(x, IER, saa7146_read(x, IER) & ~(y));
+#define SAA7146_IER_ENABLE(x,y) \
+ saa7146_write(x, IER, saa7146_read(x, IER) | (y));
+#define SAA7146_ISR_CLEAR(x,y) \
+ saa7146_write(x, ISR, (y));
+
+struct saa7146_dev;
+struct saa7146_extension;
+struct saa7146_vv;
+
+/* saa7146 page table */
+struct saa7146_pgtable {
+ unsigned int size;
+ u32 *cpu;
+ dma_addr_t dma;
+ /* used for offsets for u,v planes for planar capture modes */
+ unsigned long offset;
+ /* used for custom pagetables (used for example by budget dvb cards) */
+ struct scatterlist *slist;
+};
+
+struct saa7146_pci_extension_data {
+ struct saa7146_extension *ext;
+ void *ext_priv; /* most likely a name string */
+};
+
+#define MAKE_EXTENSION_PCI(x_var, x_vendor, x_device) \
+ { \
+ .vendor = PCI_VENDOR_ID_PHILIPS, \
+ .device = PCI_DEVICE_ID_PHILIPS_SAA7146, \
+ .subvendor = x_vendor, \
+ .subdevice = x_device, \
+ .driver_data = (unsigned long)& x_var, \
+ }
+
+struct saa7146_extension
+{
+ char name[32]; /* name of the device */
+#define SAA7146_USE_I2C_IRQ 0x1
+#define SAA7146_I2C_SHORT_DELAY 0x2
+ int flags;
+
+ /* pairs of subvendor and subdevice ids for
+ supported devices, last entry 0xffff, 0xfff */
+ struct module *module;
+ struct pci_driver driver;
+ struct pci_device_id *pci_tbl;
+
+ /* extension functions */
+ int (*probe)(struct saa7146_dev *);
+ int (*attach)(struct saa7146_dev *, struct saa7146_pci_extension_data *);
+ int (*detach)(struct saa7146_dev*);
+
+ u32 irq_mask; /* mask to indicate, which irq-events are handled by the extension */
+ void (*irq_func)(struct saa7146_dev*, u32* irq_mask);
+};
+
+struct saa7146_dma
+{
+ dma_addr_t dma_handle;
+ u32 *cpu_addr;
+};
+
+struct saa7146_dev
+{
+ struct module *module;
+
+ struct list_head item;
+
+ /* different device locks */
+ spinlock_t slock;
+ struct semaphore lock;
+
+ unsigned char __iomem *mem; /* pointer to mapped IO memory */
+ int revision; /* chip revision; needed for bug-workarounds*/
+
+ /* pci-device & irq stuff*/
+ char name[32];
+ struct pci_dev *pci;
+ u32 int_todo;
+ spinlock_t int_slock;
+
+ /* extension handling */
+ struct saa7146_extension *ext; /* indicates if handled by extension */
+ void *ext_priv; /* pointer for extension private use (most likely some private data) */
+ struct saa7146_ext_vv *ext_vv_data;
+
+ /* per device video/vbi informations (if available) */
+ struct saa7146_vv *vv_data;
+ void (*vv_callback)(struct saa7146_dev *dev, unsigned long status);
+
+ /* i2c-stuff */
+ struct semaphore i2c_lock;
+ u32 i2c_bitrate;
+ struct saa7146_dma d_i2c; /* pointer to i2c memory */
+ wait_queue_head_t i2c_wq;
+ int i2c_op;
+
+ /* memories */
+ struct saa7146_dma d_rps0;
+ struct saa7146_dma d_rps1;
+};
+
+/* from saa7146_i2c.c */
+int saa7146_i2c_adapter_prepare(struct saa7146_dev *dev, struct i2c_adapter *i2c_adapter, u32 bitrate);
+int saa7146_i2c_transfer(struct saa7146_dev *saa, const struct i2c_msg *msgs, int num, int retries);
+
+/* from saa7146_core.c */
+extern struct list_head saa7146_devices;
+extern struct semaphore saa7146_devices_lock;
+int saa7146_register_extension(struct saa7146_extension*);
+int saa7146_unregister_extension(struct saa7146_extension*);
+struct saa7146_format* format_by_fourcc(struct saa7146_dev *dev, int fourcc);
+int saa7146_pgtable_alloc(struct pci_dev *pci, struct saa7146_pgtable *pt);
+void saa7146_pgtable_free(struct pci_dev *pci, struct saa7146_pgtable *pt);
+int saa7146_pgtable_build_single(struct pci_dev *pci, struct saa7146_pgtable *pt, struct scatterlist *list, int length );
+char *saa7146_vmalloc_build_pgtable(struct pci_dev *pci, long length, struct saa7146_pgtable *pt);
+void saa7146_setgpio(struct saa7146_dev *dev, int port, u32 data);
+int saa7146_wait_for_debi_done(struct saa7146_dev *dev, int nobusyloop);
+
+/* some memory sizes */
+#define SAA7146_I2C_MEM ( 1*PAGE_SIZE)
+#define SAA7146_RPS_MEM ( 1*PAGE_SIZE)
+
+/* some i2c constants */
+#define SAA7146_I2C_TIMEOUT 100 /* i2c-timeout-value in ms */
+#define SAA7146_I2C_RETRIES 3 /* how many times shall we retry an i2c-operation? */
+#define SAA7146_I2C_DELAY 5 /* time we wait after certain i2c-operations */
+
+/* unsorted defines */
+#define ME1 0x0000000800
+#define PV1 0x0000000008
+
+/* gpio defines */
+#define SAA7146_GPIO_INPUT 0x00
+#define SAA7146_GPIO_IRQHI 0x10
+#define SAA7146_GPIO_IRQLO 0x20
+#define SAA7146_GPIO_IRQHL 0x30
+#define SAA7146_GPIO_OUTLO 0x40
+#define SAA7146_GPIO_OUTHI 0x50
+
+/* debi defines */
+#define DEBINOSWAP 0x000e0000
+
+/* define for the register programming sequencer (rps) */
+#define CMD_NOP 0x00000000 /* No operation */
+#define CMD_CLR_EVENT 0x00000000 /* Clear event */
+#define CMD_SET_EVENT 0x10000000 /* Set signal event */
+#define CMD_PAUSE 0x20000000 /* Pause */
+#define CMD_CHECK_LATE 0x30000000 /* Check late */
+#define CMD_UPLOAD 0x40000000 /* Upload */
+#define CMD_STOP 0x50000000 /* Stop */
+#define CMD_INTERRUPT 0x60000000 /* Interrupt */
+#define CMD_JUMP 0x80000000 /* Jump */
+#define CMD_WR_REG 0x90000000 /* Write (load) register */
+#define CMD_RD_REG 0xa0000000 /* Read (store) register */
+#define CMD_WR_REG_MASK 0xc0000000 /* Write register with mask */
+
+#define CMD_OAN MASK_27
+#define CMD_INV MASK_26
+#define CMD_SIG4 MASK_25
+#define CMD_SIG3 MASK_24
+#define CMD_SIG2 MASK_23
+#define CMD_SIG1 MASK_22
+#define CMD_SIG0 MASK_21
+#define CMD_O_FID_B MASK_14
+#define CMD_E_FID_B MASK_13
+#define CMD_O_FID_A MASK_12
+#define CMD_E_FID_A MASK_11
+
+/* some events and command modifiers for rps1 squarewave generator */
+#define EVT_HS (1<<15) // Source Line Threshold reached
+#define EVT_VBI_B (1<<9) // VSYNC Event
+#define RPS_OAN (1<<27) // 1: OR events, 0: AND events
+#define RPS_INV (1<<26) // Invert (compound) event
+#define GPIO3_MSK 0xFF000000 // GPIO #3 control bits
+
+/* Bit mask constants */
+#define MASK_00 0x00000001 /* Mask value for bit 0 */
+#define MASK_01 0x00000002 /* Mask value for bit 1 */
+#define MASK_02 0x00000004 /* Mask value for bit 2 */
+#define MASK_03 0x00000008 /* Mask value for bit 3 */
+#define MASK_04 0x00000010 /* Mask value for bit 4 */
+#define MASK_05 0x00000020 /* Mask value for bit 5 */
+#define MASK_06 0x00000040 /* Mask value for bit 6 */
+#define MASK_07 0x00000080 /* Mask value for bit 7 */
+#define MASK_08 0x00000100 /* Mask value for bit 8 */
+#define MASK_09 0x00000200 /* Mask value for bit 9 */
+#define MASK_10 0x00000400 /* Mask value for bit 10 */
+#define MASK_11 0x00000800 /* Mask value for bit 11 */
+#define MASK_12 0x00001000 /* Mask value for bit 12 */
+#define MASK_13 0x00002000 /* Mask value for bit 13 */
+#define MASK_14 0x00004000 /* Mask value for bit 14 */
+#define MASK_15 0x00008000 /* Mask value for bit 15 */
+#define MASK_16 0x00010000 /* Mask value for bit 16 */
+#define MASK_17 0x00020000 /* Mask value for bit 17 */
+#define MASK_18 0x00040000 /* Mask value for bit 18 */
+#define MASK_19 0x00080000 /* Mask value for bit 19 */
+#define MASK_20 0x00100000 /* Mask value for bit 20 */
+#define MASK_21 0x00200000 /* Mask value for bit 21 */
+#define MASK_22 0x00400000 /* Mask value for bit 22 */
+#define MASK_23 0x00800000 /* Mask value for bit 23 */
+#define MASK_24 0x01000000 /* Mask value for bit 24 */
+#define MASK_25 0x02000000 /* Mask value for bit 25 */
+#define MASK_26 0x04000000 /* Mask value for bit 26 */
+#define MASK_27 0x08000000 /* Mask value for bit 27 */
+#define MASK_28 0x10000000 /* Mask value for bit 28 */
+#define MASK_29 0x20000000 /* Mask value for bit 29 */
+#define MASK_30 0x40000000 /* Mask value for bit 30 */
+#define MASK_31 0x80000000 /* Mask value for bit 31 */
+
+#define MASK_B0 0x000000ff /* Mask value for byte 0 */
+#define MASK_B1 0x0000ff00 /* Mask value for byte 1 */
+#define MASK_B2 0x00ff0000 /* Mask value for byte 2 */
+#define MASK_B3 0xff000000 /* Mask value for byte 3 */
+
+#define MASK_W0 0x0000ffff /* Mask value for word 0 */
+#define MASK_W1 0xffff0000 /* Mask value for word 1 */
+
+#define MASK_PA 0xfffffffc /* Mask value for physical address */
+#define MASK_PR 0xfffffffe /* Mask value for protection register */
+#define MASK_ER 0xffffffff /* Mask value for the entire register */
+
+#define MASK_NONE 0x00000000 /* No mask */
+
+/* register aliases */
+#define BASE_ODD1 0x00 /* Video DMA 1 registers */
+#define BASE_EVEN1 0x04
+#define PROT_ADDR1 0x08
+#define PITCH1 0x0C
+#define BASE_PAGE1 0x10 /* Video DMA 1 base page */
+#define NUM_LINE_BYTE1 0x14
+
+#define BASE_ODD2 0x18 /* Video DMA 2 registers */
+#define BASE_EVEN2 0x1C
+#define PROT_ADDR2 0x20
+#define PITCH2 0x24
+#define BASE_PAGE2 0x28 /* Video DMA 2 base page */
+#define NUM_LINE_BYTE2 0x2C
+
+#define BASE_ODD3 0x30 /* Video DMA 3 registers */
+#define BASE_EVEN3 0x34
+#define PROT_ADDR3 0x38
+#define PITCH3 0x3C
+#define BASE_PAGE3 0x40 /* Video DMA 3 base page */
+#define NUM_LINE_BYTE3 0x44
+
+#define PCI_BT_V1 0x48 /* Video/FIFO 1 */
+#define PCI_BT_V2 0x49 /* Video/FIFO 2 */
+#define PCI_BT_V3 0x4A /* Video/FIFO 3 */
+#define PCI_BT_DEBI 0x4B /* DEBI */
+#define PCI_BT_A 0x4C /* Audio */
+
+#define DD1_INIT 0x50 /* Init setting of DD1 interface */
+
+#define DD1_STREAM_B 0x54 /* DD1 B video data stream handling */
+#define DD1_STREAM_A 0x56 /* DD1 A video data stream handling */
+
+#define BRS_CTRL 0x58 /* BRS control register */
+#define HPS_CTRL 0x5C /* HPS control register */
+#define HPS_V_SCALE 0x60 /* HPS vertical scale */
+#define HPS_V_GAIN 0x64 /* HPS vertical ACL and gain */
+#define HPS_H_PRESCALE 0x68 /* HPS horizontal prescale */
+#define HPS_H_SCALE 0x6C /* HPS horizontal scale */
+#define BCS_CTRL 0x70 /* BCS control */
+#define CHROMA_KEY_RANGE 0x74
+#define CLIP_FORMAT_CTRL 0x78 /* HPS outputs formats & clipping */
+
+#define DEBI_CONFIG 0x7C
+#define DEBI_COMMAND 0x80
+#define DEBI_PAGE 0x84
+#define DEBI_AD 0x88
+
+#define I2C_TRANSFER 0x8C
+#define I2C_STATUS 0x90
+
+#define BASE_A1_IN 0x94 /* Audio 1 input DMA */
+#define PROT_A1_IN 0x98
+#define PAGE_A1_IN 0x9C
+
+#define BASE_A1_OUT 0xA0 /* Audio 1 output DMA */
+#define PROT_A1_OUT 0xA4
+#define PAGE_A1_OUT 0xA8
+
+#define BASE_A2_IN 0xAC /* Audio 2 input DMA */
+#define PROT_A2_IN 0xB0
+#define PAGE_A2_IN 0xB4
+
+#define BASE_A2_OUT 0xB8 /* Audio 2 output DMA */
+#define PROT_A2_OUT 0xBC
+#define PAGE_A2_OUT 0xC0
+
+#define RPS_PAGE0 0xC4 /* RPS task 0 page register */
+#define RPS_PAGE1 0xC8 /* RPS task 1 page register */
+
+#define RPS_THRESH0 0xCC /* HBI threshold for task 0 */
+#define RPS_THRESH1 0xD0 /* HBI threshold for task 1 */
+
+#define RPS_TOV0 0xD4 /* RPS timeout for task 0 */
+#define RPS_TOV1 0xD8 /* RPS timeout for task 1 */
+
+#define IER 0xDC /* Interrupt enable register */
+
+#define GPIO_CTRL 0xE0 /* GPIO 0-3 register */
+
+#define EC1SSR 0xE4 /* Event cnt set 1 source select */
+#define EC2SSR 0xE8 /* Event cnt set 2 source select */
+#define ECT1R 0xEC /* Event cnt set 1 thresholds */
+#define ECT2R 0xF0 /* Event cnt set 2 thresholds */
+
+#define ACON1 0xF4
+#define ACON2 0xF8
+
+#define MC1 0xFC /* Main control register 1 */
+#define MC2 0x100 /* Main control register 2 */
+
+#define RPS_ADDR0 0x104 /* RPS task 0 address register */
+#define RPS_ADDR1 0x108 /* RPS task 1 address register */
+
+#define ISR 0x10C /* Interrupt status register */
+#define PSR 0x110 /* Primary status register */
+#define SSR 0x114 /* Secondary status register */
+
+#define EC1R 0x118 /* Event counter set 1 register */
+#define EC2R 0x11C /* Event counter set 2 register */
+
+#define PCI_VDP1 0x120 /* Video DMA pointer of FIFO 1 */
+#define PCI_VDP2 0x124 /* Video DMA pointer of FIFO 2 */
+#define PCI_VDP3 0x128 /* Video DMA pointer of FIFO 3 */
+#define PCI_ADP1 0x12C /* Audio DMA pointer of audio out 1 */
+#define PCI_ADP2 0x130 /* Audio DMA pointer of audio in 1 */
+#define PCI_ADP3 0x134 /* Audio DMA pointer of audio out 2 */
+#define PCI_ADP4 0x138 /* Audio DMA pointer of audio in 2 */
+#define PCI_DMA_DDP 0x13C /* DEBI DMA pointer */
+
+#define LEVEL_REP 0x140,
+#define A_TIME_SLOT1 0x180, /* from 180 - 1BC */
+#define A_TIME_SLOT2 0x1C0, /* from 1C0 - 1FC */
+
+/* isr masks */
+#define SPCI_PPEF 0x80000000 /* PCI parity error */
+#define SPCI_PABO 0x40000000 /* PCI access error (target or master abort) */
+#define SPCI_PPED 0x20000000 /* PCI parity error on 'real time data' */
+#define SPCI_RPS_I1 0x10000000 /* Interrupt issued by RPS1 */
+#define SPCI_RPS_I0 0x08000000 /* Interrupt issued by RPS0 */
+#define SPCI_RPS_LATE1 0x04000000 /* RPS task 1 is late */
+#define SPCI_RPS_LATE0 0x02000000 /* RPS task 0 is late */
+#define SPCI_RPS_E1 0x01000000 /* RPS error from task 1 */
+#define SPCI_RPS_E0 0x00800000 /* RPS error from task 0 */
+#define SPCI_RPS_TO1 0x00400000 /* RPS timeout task 1 */
+#define SPCI_RPS_TO0 0x00200000 /* RPS timeout task 0 */
+#define SPCI_UPLD 0x00100000 /* RPS in upload */
+#define SPCI_DEBI_S 0x00080000 /* DEBI status */
+#define SPCI_DEBI_E 0x00040000 /* DEBI error */
+#define SPCI_IIC_S 0x00020000 /* I2C status */
+#define SPCI_IIC_E 0x00010000 /* I2C error */
+#define SPCI_A2_IN 0x00008000 /* Audio 2 input DMA protection / limit */
+#define SPCI_A2_OUT 0x00004000 /* Audio 2 output DMA protection / limit */
+#define SPCI_A1_IN 0x00002000 /* Audio 1 input DMA protection / limit */
+#define SPCI_A1_OUT 0x00001000 /* Audio 1 output DMA protection / limit */
+#define SPCI_AFOU 0x00000800 /* Audio FIFO over- / underflow */
+#define SPCI_V_PE 0x00000400 /* Video protection address */
+#define SPCI_VFOU 0x00000200 /* Video FIFO over- / underflow */
+#define SPCI_FIDA 0x00000100 /* Field ID video port A */
+#define SPCI_FIDB 0x00000080 /* Field ID video port B */
+#define SPCI_PIN3 0x00000040 /* GPIO pin 3 */
+#define SPCI_PIN2 0x00000020 /* GPIO pin 2 */
+#define SPCI_PIN1 0x00000010 /* GPIO pin 1 */
+#define SPCI_PIN0 0x00000008 /* GPIO pin 0 */
+#define SPCI_ECS 0x00000004 /* Event counter 1, 2, 4, 5 */
+#define SPCI_EC3S 0x00000002 /* Event counter 3 */
+#define SPCI_EC0S 0x00000001 /* Event counter 0 */
+
+/* i2c */
+#define SAA7146_I2C_ABORT (1<<7)
+#define SAA7146_I2C_SPERR (1<<6)
+#define SAA7146_I2C_APERR (1<<5)
+#define SAA7146_I2C_DTERR (1<<4)
+#define SAA7146_I2C_DRERR (1<<3)
+#define SAA7146_I2C_AL (1<<2)
+#define SAA7146_I2C_ERR (1<<1)
+#define SAA7146_I2C_BUSY (1<<0)
+
+#define SAA7146_I2C_START (0x3)
+#define SAA7146_I2C_CONT (0x2)
+#define SAA7146_I2C_STOP (0x1)
+#define SAA7146_I2C_NOP (0x0)
+
+#define SAA7146_I2C_BUS_BIT_RATE_6400 (0x500)
+#define SAA7146_I2C_BUS_BIT_RATE_3200 (0x100)
+#define SAA7146_I2C_BUS_BIT_RATE_480 (0x400)
+#define SAA7146_I2C_BUS_BIT_RATE_320 (0x600)
+#define SAA7146_I2C_BUS_BIT_RATE_240 (0x700)
+#define SAA7146_I2C_BUS_BIT_RATE_120 (0x000)
+#define SAA7146_I2C_BUS_BIT_RATE_80 (0x200)
+#define SAA7146_I2C_BUS_BIT_RATE_60 (0x300)
+
+#endif
diff --git a/include/media/saa7146_vv.h b/include/media/saa7146_vv.h
new file mode 100644
index 0000000..f3aa24f
--- /dev/null
+++ b/include/media/saa7146_vv.h
@@ -0,0 +1,270 @@
+#ifndef __SAA7146_VV__
+#define __SAA7146_VV__
+
+#include <linux/videodev2.h>
+
+#include <media/saa7146.h>
+#include <media/video-buf.h>
+
+#define MAX_SAA7146_CAPTURE_BUFFERS 32 /* arbitrary */
+#define BUFFER_TIMEOUT (HZ/2) /* 0.5 seconds */
+
+#define WRITE_RPS0(x) do { \
+ dev->d_rps0.cpu_addr[ count++ ] = cpu_to_le32(x); \
+ } while (0);
+
+#define WRITE_RPS1(x) do { \
+ dev->d_rps1.cpu_addr[ count++ ] = cpu_to_le32(x); \
+ } while (0);
+
+struct saa7146_video_dma {
+ u32 base_odd;
+ u32 base_even;
+ u32 prot_addr;
+ u32 pitch;
+ u32 base_page;
+ u32 num_line_byte;
+};
+
+#define FORMAT_BYTE_SWAP 0x1
+#define FORMAT_IS_PLANAR 0x2
+
+struct saa7146_format {
+ char *name;
+ u32 pixelformat;
+ u32 trans;
+ u8 depth;
+ u8 flags;
+ u8 swap;
+};
+
+struct saa7146_standard
+{
+ char *name;
+ v4l2_std_id id;
+
+ int v_offset; /* number of lines of vertical offset before processing */
+ int v_field; /* number of lines in a field for HPS to process */
+
+ int h_offset; /* horizontal offset of processing window */
+ int h_pixels; /* number of horizontal pixels to process */
+
+ int v_max_out;
+ int h_max_out;
+};
+
+/* buffer for one video/vbi frame */
+struct saa7146_buf {
+ /* common v4l buffer stuff -- must be first */
+ struct videobuf_buffer vb;
+
+ /* saa7146 specific */
+ struct v4l2_pix_format *fmt;
+ int (*activate)(struct saa7146_dev *dev,
+ struct saa7146_buf *buf,
+ struct saa7146_buf *next);
+
+ /* page tables */
+ struct saa7146_pgtable pt[3];
+};
+
+struct saa7146_dmaqueue {
+ struct saa7146_dev *dev;
+ struct saa7146_buf *curr;
+ struct list_head queue;
+ struct timer_list timeout;
+};
+
+struct saa7146_overlay {
+ struct saa7146_fh *fh;
+ struct v4l2_window win;
+ struct v4l2_clip clips[16];
+ int nclips;
+};
+
+/* per open data */
+struct saa7146_fh {
+ struct saa7146_dev *dev;
+ /* if this is a vbi or capture open */
+ enum v4l2_buf_type type;
+
+ /* video overlay */
+ struct saa7146_overlay ov;
+
+ /* video capture */
+ struct videobuf_queue video_q;
+ struct v4l2_pix_format video_fmt;
+
+ /* vbi capture */
+ struct videobuf_queue vbi_q;
+ struct v4l2_vbi_format vbi_fmt;
+ struct timer_list vbi_read_timeout;
+
+ unsigned int resources; /* resource management for device open */
+};
+
+#define STATUS_OVERLAY 0x01
+#define STATUS_CAPTURE 0x02
+
+struct saa7146_vv
+{
+ int vbi_minor;
+
+ /* vbi capture */
+ struct saa7146_dmaqueue vbi_q;
+ /* vbi workaround interrupt queue */
+ wait_queue_head_t vbi_wq;
+ int vbi_fieldcount;
+ struct saa7146_fh *vbi_streaming;
+
+ int video_minor;
+
+ int video_status;
+ struct saa7146_fh *video_fh;
+
+ /* video overlay */
+ struct v4l2_framebuffer ov_fb;
+ struct saa7146_format *ov_fmt;
+ struct saa7146_overlay *ov_data;
+ struct saa7146_fh *ov_suspend;
+
+ /* video capture */
+ struct saa7146_dmaqueue video_q;
+ enum v4l2_field last_field;
+
+ /* common: fixme? shouldn't this be in saa7146_fh?
+ (this leads to a more complicated question: shall the driver
+ store the different settings (for example S_INPUT) for every open
+ and restore it appropriately, or should all settings be common for
+ all opens? currently, we do the latter, like all other
+ drivers do... */
+ struct saa7146_standard *standard;
+
+ int vflip;
+ int hflip;
+ int current_hps_source;
+ int current_hps_sync;
+
+ struct saa7146_dma d_clipping; /* pointer to clipping memory */
+
+ unsigned int resources; /* resource management for device */
+};
+
+#define SAA7146_EXCLUSIVE 0x1
+#define SAA7146_BEFORE 0x2
+#define SAA7146_AFTER 0x4
+
+struct saa7146_extension_ioctls
+{
+ unsigned int cmd;
+ int flags;
+};
+
+/* flags */
+#define SAA7146_USE_PORT_B_FOR_VBI 0x2 /* use input port b for vbi hardware bug workaround */
+
+struct saa7146_ext_vv
+{
+ /* informations about the video capabilities of the device */
+ int inputs;
+ int audios;
+ u32 capabilities;
+ int flags;
+
+ /* additionally supported transmission standards */
+ struct saa7146_standard *stds;
+ int num_stds;
+ int (*std_callback)(struct saa7146_dev*, struct saa7146_standard *);
+
+ struct saa7146_extension_ioctls *ioctls;
+ int (*ioctl)(struct saa7146_fh*, unsigned int cmd, void *arg);
+};
+
+struct saa7146_use_ops {
+ void (*init)(struct saa7146_dev *, struct saa7146_vv *);
+ int(*open)(struct saa7146_dev *, struct file *);
+ void (*release)(struct saa7146_dev *, struct file *);
+ void (*irq_done)(struct saa7146_dev *, unsigned long status);
+ ssize_t (*read)(struct file *, char __user *, size_t, loff_t *);
+};
+
+/* from saa7146_fops.c */
+int saa7146_register_device(struct video_device **vid, struct saa7146_dev* dev, char *name, int type);
+int saa7146_unregister_device(struct video_device **vid, struct saa7146_dev* dev);
+void saa7146_buffer_finish(struct saa7146_dev *dev, struct saa7146_dmaqueue *q, int state);
+void saa7146_buffer_next(struct saa7146_dev *dev, struct saa7146_dmaqueue *q,int vbi);
+int saa7146_buffer_queue(struct saa7146_dev *dev, struct saa7146_dmaqueue *q, struct saa7146_buf *buf);
+void saa7146_buffer_timeout(unsigned long data);
+void saa7146_dma_free(struct saa7146_dev *dev,struct saa7146_buf *buf);
+
+int saa7146_vv_init(struct saa7146_dev* dev, struct saa7146_ext_vv *ext_vv);
+int saa7146_vv_release(struct saa7146_dev* dev);
+
+/* from saa7146_hlp.c */
+int saa7146_enable_overlay(struct saa7146_fh *fh);
+void saa7146_disable_overlay(struct saa7146_fh *fh);
+
+void saa7146_set_capture(struct saa7146_dev *dev, struct saa7146_buf *buf, struct saa7146_buf *next);
+void saa7146_write_out_dma(struct saa7146_dev* dev, int which, struct saa7146_video_dma* vdma) ;
+void saa7146_set_hps_source_and_sync(struct saa7146_dev *saa, int source, int sync);
+void saa7146_set_gpio(struct saa7146_dev *saa, u8 pin, u8 data);
+
+/* from saa7146_video.c */
+extern struct saa7146_use_ops saa7146_video_uops;
+int saa7146_start_preview(struct saa7146_fh *fh);
+int saa7146_stop_preview(struct saa7146_fh *fh);
+
+/* from saa7146_vbi.c */
+extern struct saa7146_use_ops saa7146_vbi_uops;
+
+/* resource management functions */
+int saa7146_res_get(struct saa7146_fh *fh, unsigned int bit);
+void saa7146_res_free(struct saa7146_fh *fh, unsigned int bits);
+
+#define RESOURCE_DMA1_HPS 0x1
+#define RESOURCE_DMA2_CLP 0x2
+#define RESOURCE_DMA3_BRS 0x4
+
+/* saa7146 source inputs */
+#define SAA7146_HPS_SOURCE_PORT_A 0x00
+#define SAA7146_HPS_SOURCE_PORT_B 0x01
+#define SAA7146_HPS_SOURCE_YPB_CPA 0x02
+#define SAA7146_HPS_SOURCE_YPA_CPB 0x03
+
+/* sync inputs */
+#define SAA7146_HPS_SYNC_PORT_A 0x00
+#define SAA7146_HPS_SYNC_PORT_B 0x01
+
+/* some memory sizes */
+#define SAA7146_CLIPPING_MEM (14*PAGE_SIZE)
+
+/* some defines for the various clipping-modes */
+#define SAA7146_CLIPPING_RECT 0x4
+#define SAA7146_CLIPPING_RECT_INVERTED 0x5
+#define SAA7146_CLIPPING_MASK 0x6
+#define SAA7146_CLIPPING_MASK_INVERTED 0x7
+
+/* output formats: each entry holds four informations */
+#define RGB08_COMPOSED 0x0217 /* composed is used in the sense of "not-planar" */
+/* this means: planar?=0, yuv2rgb-conversation-mode=2, dither=yes(=1), format-mode = 7 */
+#define RGB15_COMPOSED 0x0213
+#define RGB16_COMPOSED 0x0210
+#define RGB24_COMPOSED 0x0201
+#define RGB32_COMPOSED 0x0202
+
+#define Y8 0x0006
+#define YUV411_COMPOSED 0x0003
+#define YUV422_COMPOSED 0x0000
+/* this means: planar?=1, yuv2rgb-conversion-mode=0, dither=no(=0), format-mode = b */
+#define YUV411_DECOMPOSED 0x100b
+#define YUV422_DECOMPOSED 0x1009
+#define YUV420_DECOMPOSED 0x100a
+
+#define IS_PLANAR(x) (x & 0xf000)
+
+/* misc defines */
+#define SAA7146_NO_SWAP (0x0)
+#define SAA7146_TWO_BYTE_SWAP (0x1)
+#define SAA7146_FOUR_BYTE_SWAP (0x2)
+
+#endif
diff --git a/include/media/tuner.h b/include/media/tuner.h
new file mode 100644
index 0000000..156a9c5
--- /dev/null
+++ b/include/media/tuner.h
@@ -0,0 +1,199 @@
+
+/*
+ tuner.h - definition for different tuners
+
+ Copyright (C) 1997 Markus Schroeder (schroedm@uni-duesseldorf.de)
+ minor modifications by Ralph Metzler (rjkm@thp.uni-koeln.de)
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+
+#ifndef _TUNER_H
+#define _TUNER_H
+
+#include "id.h"
+
+#define TUNER_TEMIC_PAL 0 /* 4002 FH5 (3X 7756, 9483) */
+#define TUNER_PHILIPS_PAL_I 1
+#define TUNER_PHILIPS_NTSC 2
+#define TUNER_PHILIPS_SECAM 3 /* you must actively select B/G, L, L` */
+
+#define TUNER_ABSENT 4
+#define TUNER_PHILIPS_PAL 5
+#define TUNER_TEMIC_NTSC 6 /* 4032 FY5 (3X 7004, 9498, 9789) */
+#define TUNER_TEMIC_PAL_I 7 /* 4062 FY5 (3X 8501, 9957) */
+
+#define TUNER_TEMIC_4036FY5_NTSC 8 /* 4036 FY5 (3X 1223, 1981, 7686) */
+#define TUNER_ALPS_TSBH1_NTSC 9
+#define TUNER_ALPS_TSBE1_PAL 10
+#define TUNER_ALPS_TSBB5_PAL_I 11
+
+#define TUNER_ALPS_TSBE5_PAL 12
+#define TUNER_ALPS_TSBC5_PAL 13
+#define TUNER_TEMIC_4006FH5_PAL 14 /* 4006 FH5 (3X 9500, 9501, 7291) */
+#define TUNER_ALPS_TSHC6_NTSC 15
+
+#define TUNER_TEMIC_PAL_DK 16 /* 4016 FY5 (3X 1392, 1393) */
+#define TUNER_PHILIPS_NTSC_M 17
+#define TUNER_TEMIC_4066FY5_PAL_I 18 /* 4066 FY5 (3X 7032, 7035) */
+#define TUNER_TEMIC_4006FN5_MULTI_PAL 19 /* B/G, I and D/K autodetected (3X 7595, 7606, 7657)*/
+
+#define TUNER_TEMIC_4009FR5_PAL 20 /* incl. FM radio (3X 7607, 7488, 7711)*/
+#define TUNER_TEMIC_4039FR5_NTSC 21 /* incl. FM radio (3X 7246, 7578, 7732)*/
+#define TUNER_TEMIC_4046FM5 22 /* you must actively select B/G, D/K, I, L, L` ! (3X 7804, 7806, 8103, 8104)*/
+#define TUNER_PHILIPS_PAL_DK 23
+
+#define TUNER_PHILIPS_FQ1216ME 24 /* you must actively select B/G/D/K, I, L, L` */
+#define TUNER_LG_PAL_I_FM 25
+#define TUNER_LG_PAL_I 26
+#define TUNER_LG_NTSC_FM 27
+
+#define TUNER_LG_PAL_FM 28
+#define TUNER_LG_PAL 29
+#define TUNER_TEMIC_4009FN5_MULTI_PAL_FM 30 /* B/G, I and D/K autodetected (3X 8155, 8160, 8163)*/
+#define TUNER_SHARP_2U5JF5540_NTSC 31
+
+#define TUNER_Samsung_PAL_TCPM9091PD27 32
+#define TUNER_MT2032 33
+#define TUNER_TEMIC_4106FH5 34 /* 4106 FH5 (3X 7808, 7865)*/
+#define TUNER_TEMIC_4012FY5 35 /* 4012 FY5 (3X 0971, 1099)*/
+
+#define TUNER_TEMIC_4136FY5 36 /* 4136 FY5 (3X 7708, 7746)*/
+#define TUNER_LG_PAL_NEW_TAPC 37
+#define TUNER_PHILIPS_FM1216ME_MK3 38
+#define TUNER_LG_NTSC_NEW_TAPC 39
+
+#define TUNER_HITACHI_NTSC 40
+#define TUNER_PHILIPS_PAL_MK 41
+#define TUNER_PHILIPS_ATSC 42
+#define TUNER_PHILIPS_FM1236_MK3 43
+
+#define TUNER_PHILIPS_4IN1 44 /* ATI TV Wonder Pro - Conexant */
+/* Microtune mergeged with Temic 12/31/1999 partially financed by Alps - these may be similar to Temic */
+#define TUNER_MICROTUNE_4049FM5 45
+#define TUNER_LG_NTSC_TAPE 47
+
+#define TUNER_TNF_8831BGFF 48
+#define TUNER_MICROTUNE_4042FI5 49 /* FusionHDTV 3 Gold - 4042 FI5 (3X 8147) */
+#define TUNER_TCL_2002N 50
+#define TUNER_PHILIPS_FM1256_IH3 51
+
+#define TUNER_THOMSON_DTT7610 52
+#define TUNER_PHILIPS_FQ1286 53
+#define TUNER_PHILIPS_TDA8290 54
+#define TUNER_LG_PAL_TAPE 55 /* Hauppauge PVR-150 PAL */
+
+#define TUNER_PHILIPS_FQ1216AME_MK4 56 /* Hauppauge PVR-150 PAL */
+#define TUNER_PHILIPS_FQ1236A_MK4 57 /* Hauppauge PVR-500MCE NTSC */
+
+#define NOTUNER 0
+#define PAL 1 /* PAL_BG */
+#define PAL_I 2
+#define NTSC 3
+#define SECAM 4
+#define ATSC 5
+
+#define NoTuner 0
+#define Philips 1
+#define TEMIC 2
+#define Sony 3
+#define Alps 4
+#define LGINNOTEK 5
+#define SHARP 6
+#define Samsung 7
+#define Microtune 8
+#define HITACHI 9
+#define Panasonic 10
+#define TCL 11
+#define THOMSON 12
+
+#define TUNER_SET_TYPE _IOW('t',1,int) /* set tuner type */
+#define TUNER_SET_TVFREQ _IOW('t',2,int) /* set tv freq */
+
+#define TDA9887_SET_CONFIG _IOW('t',5,int)
+/* tv card specific */
+# define TDA9887_PRESENT (1<<0)
+# define TDA9887_PORT1_INACTIVE (1<<1)
+# define TDA9887_PORT2_INACTIVE (1<<2)
+# define TDA9887_QSS (1<<3)
+# define TDA9887_INTERCARRIER (1<<4)
+# define TDA9887_PORT1_ACTIVE (1<<5)
+# define TDA9887_PORT2_ACTIVE (1<<6)
+/* config options */
+# define TDA9887_DEEMPHASIS_MASK (3<<16)
+# define TDA9887_DEEMPHASIS_NONE (1<<16)
+# define TDA9887_DEEMPHASIS_50 (2<<16)
+# define TDA9887_DEEMPHASIS_75 (3<<16)
+# define TDA9887_AUTOMUTE (1<<18)
+
+#ifdef __KERNEL__
+
+#define I2C_ADDR_TDA8290 0x4b
+#define I2C_ADDR_TDA8275 0x61
+
+struct tuner {
+ /* device */
+ struct i2c_client i2c;
+
+ /* state + config */
+ unsigned int initialized;
+ unsigned int type; /* chip type */
+ unsigned int freq; /* keep track of the current settings */
+ v4l2_std_id std;
+ int using_v4l2;
+
+ enum v4l2_tuner_type mode;
+ unsigned int input;
+
+ /* used by MT2032 */
+ unsigned int xogc;
+ unsigned int radio_if2;
+
+ /* used by tda8290 */
+ unsigned char i2c_easy_mode[2];
+ unsigned char i2c_set_freq[8];
+
+ /* function ptrs */
+ void (*tv_freq)(struct i2c_client *c, unsigned int freq);
+ void (*radio_freq)(struct i2c_client *c, unsigned int freq);
+ int (*has_signal)(struct i2c_client *c);
+ int (*is_stereo)(struct i2c_client *c);
+};
+
+extern unsigned int tuner_debug;
+extern unsigned const int tuner_count;
+
+extern int microtune_init(struct i2c_client *c);
+extern int tda8290_init(struct i2c_client *c);
+extern int default_tuner_init(struct i2c_client *c);
+
+#define tuner_warn(fmt, arg...) \
+ dev_printk(KERN_WARNING , &t->i2c.dev , fmt , ## arg)
+#define tuner_info(fmt, arg...) \
+ dev_printk(KERN_INFO , &t->i2c.dev , fmt , ## arg)
+#define tuner_dbg(fmt, arg...) \
+ if (tuner_debug) dev_printk(KERN_DEBUG , &t->i2c.dev , fmt , ## arg)
+
+#endif /* __KERNEL__ */
+
+#endif
+
+/*
+ * Overrides for Emacs so that we follow Linus's tabbing style.
+ * ---------------------------------------------------------------------------
+ * Local variables:
+ * c-basic-offset: 8
+ * End:
+ */
diff --git a/include/media/tveeprom.h b/include/media/tveeprom.h
new file mode 100644
index 0000000..627603e
--- /dev/null
+++ b/include/media/tveeprom.h
@@ -0,0 +1,23 @@
+struct tveeprom {
+ u32 has_radio;
+
+ u32 tuner_type;
+ u32 tuner_formats;
+
+ u32 digitizer;
+ u32 digitizer_formats;
+
+ u32 audio_processor;
+ /* a_p_fmts? */
+
+ u32 model;
+ u32 revision;
+ u32 serial_number;
+ char rev_str[5];
+};
+
+void tveeprom_hauppauge_analog(struct tveeprom *tvee,
+ unsigned char *eeprom_data);
+
+int tveeprom_read(struct i2c_client *c, unsigned char *eedata, int len);
+int tveeprom_dump(unsigned char *eedata, int len);
diff --git a/include/media/video-buf-dvb.h b/include/media/video-buf-dvb.h
new file mode 100644
index 0000000..94bd336
--- /dev/null
+++ b/include/media/video-buf-dvb.h
@@ -0,0 +1,36 @@
+#include <dvbdev.h>
+#include <dmxdev.h>
+#include <dvb_demux.h>
+#include <dvb_net.h>
+#include <dvb_frontend.h>
+
+struct videobuf_dvb {
+ /* filling that the job of the driver */
+ char *name;
+ struct dvb_frontend *frontend;
+ struct videobuf_queue dvbq;
+
+ /* video-buf-dvb state info */
+ struct semaphore lock;
+ struct task_struct *thread;
+ int nfeeds;
+
+ /* videobuf_dvb_(un)register manges this */
+ struct dvb_adapter *adapter;
+ struct dvb_demux demux;
+ struct dmxdev dmxdev;
+ struct dmx_frontend fe_hw;
+ struct dmx_frontend fe_mem;
+ struct dvb_net net;
+};
+
+int videobuf_dvb_register(struct videobuf_dvb *dvb,
+ struct module *module,
+ void *adapter_priv);
+void videobuf_dvb_unregister(struct videobuf_dvb *dvb);
+
+/*
+ * Local variables:
+ * c-basic-offset: 8
+ * End:
+ */
diff --git a/include/media/video-buf.h b/include/media/video-buf.h
new file mode 100644
index 0000000..ae6da6d
--- /dev/null
+++ b/include/media/video-buf.h
@@ -0,0 +1,260 @@
+/*
+ * $Id: video-buf.h,v 1.9 2004/11/07 13:17:15 kraxel Exp $
+ *
+ * generic helper functions for video4linux capture buffers, to handle
+ * memory management and PCI DMA. Right now bttv + saa7134 use it.
+ *
+ * The functions expect the hardware being able to scatter gatter
+ * (i.e. the buffers are not linear in physical memory, but fragmented
+ * into PAGE_SIZE chunks). They also assume the driver does not need
+ * to touch the video data (thus it is probably not useful for USB as
+ * data often must be uncompressed by the drivers).
+ *
+ * (c) 2001,02 Gerd Knorr <kraxel@bytesex.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/videodev.h>
+
+#define UNSET (-1U)
+
+/* --------------------------------------------------------------------- */
+
+/*
+ * Return a scatterlist for some page-aligned vmalloc()'ed memory
+ * block (NULL on errors). Memory for the scatterlist is allocated
+ * using kmalloc. The caller must free the memory.
+ */
+struct scatterlist* videobuf_vmalloc_to_sg(unsigned char *virt, int nr_pages);
+
+/*
+ * Return a scatterlist for a an array of userpages (NULL on errors).
+ * Memory for the scatterlist is allocated using kmalloc. The caller
+ * must free the memory.
+ */
+struct scatterlist* videobuf_pages_to_sg(struct page **pages, int nr_pages,
+ int offset);
+
+/* --------------------------------------------------------------------- */
+
+/*
+ * A small set of helper functions to manage buffers (both userland
+ * and kernel) for DMA.
+ *
+ * videobuf_dma_init_*()
+ * creates a buffer. The userland version takes a userspace
+ * pointer + length. The kernel version just wants the size and
+ * does memory allocation too using vmalloc_32().
+ *
+ * videobuf_dma_pci_*()
+ * see Documentation/DMA-mapping.txt, these functions to
+ * basically the same. The map function does also build a
+ * scatterlist for the buffer (and unmap frees it ...)
+ *
+ * videobuf_dma_free()
+ * no comment ...
+ *
+ */
+
+struct videobuf_dmabuf {
+ u32 magic;
+
+ /* for userland buffer */
+ int offset;
+ struct page **pages;
+
+ /* for kernel buffers */
+ void *vmalloc;
+
+ /* for overlay buffers (pci-pci dma) */
+ dma_addr_t bus_addr;
+
+ /* common */
+ struct scatterlist *sglist;
+ int sglen;
+ int nr_pages;
+ int direction;
+};
+
+void videobuf_dma_init(struct videobuf_dmabuf *dma);
+int videobuf_dma_init_user(struct videobuf_dmabuf *dma, int direction,
+ unsigned long data, unsigned long size);
+int videobuf_dma_init_kernel(struct videobuf_dmabuf *dma, int direction,
+ int nr_pages);
+int videobuf_dma_init_overlay(struct videobuf_dmabuf *dma, int direction,
+ dma_addr_t addr, int nr_pages);
+int videobuf_dma_pci_map(struct pci_dev *dev, struct videobuf_dmabuf *dma);
+int videobuf_dma_pci_sync(struct pci_dev *dev,
+ struct videobuf_dmabuf *dma);
+int videobuf_dma_pci_unmap(struct pci_dev *dev, struct videobuf_dmabuf *dma);
+int videobuf_dma_free(struct videobuf_dmabuf *dma);
+
+/* --------------------------------------------------------------------- */
+
+/*
+ * A small set of helper functions to manage video4linux buffers.
+ *
+ * struct videobuf_buffer holds the data structures used by the helper
+ * functions, additionally some commonly used fields for v4l buffers
+ * (width, height, lists, waitqueue) are in there. That struct should
+ * be used as first element in the drivers buffer struct.
+ *
+ * about the mmap helpers (videobuf_mmap_*):
+ *
+ * The mmaper function allows to map any subset of contingous buffers.
+ * This includes one mmap() call for all buffers (which the original
+ * video4linux API uses) as well as one mmap() for every single buffer
+ * (which v4l2 uses).
+ *
+ * If there is a valid mapping for a buffer, buffer->baddr/bsize holds
+ * userspace address + size which can be feeded into the
+ * videobuf_dma_init_user function listed above.
+ *
+ */
+
+struct videobuf_buffer;
+struct videobuf_queue;
+
+struct videobuf_mapping {
+ unsigned int count;
+ unsigned long start;
+ unsigned long end;
+ struct videobuf_queue *q;
+};
+
+enum videobuf_state {
+ STATE_NEEDS_INIT = 0,
+ STATE_PREPARED = 1,
+ STATE_QUEUED = 2,
+ STATE_ACTIVE = 3,
+ STATE_DONE = 4,
+ STATE_ERROR = 5,
+ STATE_IDLE = 6,
+};
+
+struct videobuf_buffer {
+ unsigned int i;
+ u32 magic;
+
+ /* info about the buffer */
+ unsigned int width;
+ unsigned int height;
+ unsigned int bytesperline; /* use only if != 0 */
+ unsigned long size;
+ unsigned int input;
+ enum v4l2_field field;
+ enum videobuf_state state;
+ struct videobuf_dmabuf dma;
+ struct list_head stream; /* QBUF/DQBUF list */
+
+ /* for mmap'ed buffers */
+ enum v4l2_memory memory;
+ size_t boff; /* buffer offset (mmap + overlay) */
+ size_t bsize; /* buffer size */
+ unsigned long baddr; /* buffer addr (userland ptr!) */
+ struct videobuf_mapping *map;
+
+ /* touched by irq handler */
+ struct list_head queue;
+ wait_queue_head_t done;
+ unsigned int field_count;
+ struct timeval ts;
+};
+
+struct videobuf_queue_ops {
+ int (*buf_setup)(struct videobuf_queue *q,
+ unsigned int *count, unsigned int *size);
+ int (*buf_prepare)(struct videobuf_queue *q,
+ struct videobuf_buffer *vb,
+ enum v4l2_field field);
+ void (*buf_queue)(struct videobuf_queue *q,
+ struct videobuf_buffer *vb);
+ void (*buf_release)(struct videobuf_queue *q,
+ struct videobuf_buffer *vb);
+};
+
+struct videobuf_queue {
+ struct semaphore lock;
+ spinlock_t *irqlock;
+ struct pci_dev *pci;
+
+ enum v4l2_buf_type type;
+ unsigned int inputs; /* for V4L2_BUF_FLAG_INPUT */
+ unsigned int msize;
+ enum v4l2_field field;
+ enum v4l2_field last; /* for field=V4L2_FIELD_ALTERNATE */
+ struct videobuf_buffer *bufs[VIDEO_MAX_FRAME];
+ struct videobuf_queue_ops *ops;
+
+ /* capture via mmap() + ioctl(QBUF/DQBUF) */
+ unsigned int streaming;
+ struct list_head stream;
+
+ /* capture via read() */
+ unsigned int reading;
+ unsigned int read_off;
+ struct videobuf_buffer *read_buf;
+
+ /* driver private data */
+ void *priv_data;
+};
+
+void* videobuf_alloc(unsigned int size);
+int videobuf_waiton(struct videobuf_buffer *vb, int non_blocking, int intr);
+int videobuf_iolock(struct pci_dev *pci, struct videobuf_buffer *vb,
+ struct v4l2_framebuffer *fbuf);
+
+void videobuf_queue_init(struct videobuf_queue *q,
+ struct videobuf_queue_ops *ops,
+ struct pci_dev *pci,
+ spinlock_t *irqlock,
+ enum v4l2_buf_type type,
+ enum v4l2_field field,
+ unsigned int msize,
+ void *priv);
+int videobuf_queue_is_busy(struct videobuf_queue *q);
+void videobuf_queue_cancel(struct videobuf_queue *q);
+
+enum v4l2_field videobuf_next_field(struct videobuf_queue *q);
+void videobuf_status(struct v4l2_buffer *b, struct videobuf_buffer *vb,
+ enum v4l2_buf_type type);
+int videobuf_reqbufs(struct videobuf_queue *q,
+ struct v4l2_requestbuffers *req);
+int videobuf_querybuf(struct videobuf_queue *q, struct v4l2_buffer *b);
+int videobuf_qbuf(struct videobuf_queue *q,
+ struct v4l2_buffer *b);
+int videobuf_dqbuf(struct videobuf_queue *q,
+ struct v4l2_buffer *b, int nonblocking);
+int videobuf_streamon(struct videobuf_queue *q);
+int videobuf_streamoff(struct videobuf_queue *q);
+
+int videobuf_read_start(struct videobuf_queue *q);
+void videobuf_read_stop(struct videobuf_queue *q);
+ssize_t videobuf_read_stream(struct videobuf_queue *q,
+ char __user *data, size_t count, loff_t *ppos,
+ int vbihack, int nonblocking);
+ssize_t videobuf_read_one(struct videobuf_queue *q,
+ char __user *data, size_t count, loff_t *ppos,
+ int nonblocking);
+unsigned int videobuf_poll_stream(struct file *file,
+ struct videobuf_queue *q,
+ poll_table *wait);
+
+int videobuf_mmap_setup(struct videobuf_queue *q,
+ unsigned int bcount, unsigned int bsize,
+ enum v4l2_memory memory);
+int videobuf_mmap_free(struct videobuf_queue *q);
+int videobuf_mmap_mapper(struct videobuf_queue *q,
+ struct vm_area_struct *vma);
+
+/* --------------------------------------------------------------------- */
+
+/*
+ * Local variables:
+ * c-basic-offset: 8
+ * End:
+ */