[ARM] 5026/1: locomo: add .settype for gpio and several small fixes
irqs.h:
* rename IRQ_LOCOMO_SPI_OVRN to IRQ_LOCOMO_SPI_REND
locomo.h:
* add some definition for locomo spi controller
* correct some errors
locomo.c:
* correct some errors
* add set_type for locomo gpio irq chip
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/include/asm-arm/hardware/locomo.h b/include/asm-arm/hardware/locomo.h
index adab777..fb0645d 100644
--- a/include/asm-arm/hardware/locomo.h
+++ b/include/asm-arm/hardware/locomo.h
@@ -58,6 +58,11 @@
#define LOCOMO_SPIMD 0x00 /* SPI mode setting */
#define LOCOMO_SPICT 0x04 /* SPI mode control */
#define LOCOMO_SPIST 0x08 /* SPI status */
+#define LOCOMO_SPI_TEND (1 << 3) /* Transfer end bit */
+#define LOCOMO_SPI_REND (1 << 2) /* Receive end bit */
+#define LOCOMO_SPI_RFW (1 << 1) /* write buffer bit */
+#define LOCOMO_SPI_RFR (1) /* read buffer bit */
+
#define LOCOMO_SPIIS 0x10 /* SPI interrupt status */
#define LOCOMO_SPIWE 0x14 /* SPI interrupt status write enable */
#define LOCOMO_SPIIE 0x18 /* SPI interrupt enable */
@@ -66,16 +71,12 @@
#define LOCOMO_SPIRD 0x24 /* SPI receive data read */
#define LOCOMO_SPITS 0x28 /* SPI transfer data shift */
#define LOCOMO_SPIRS 0x2C /* SPI receive data shift */
-#define LOCOMO_SPI_TEND (1 << 3) /* Transfer end bit */
-#define LOCOMO_SPI_OVRN (1 << 2) /* Over Run bit */
-#define LOCOMO_SPI_RFW (1 << 1) /* write buffer bit */
-#define LOCOMO_SPI_RFR (1) /* read buffer bit */
/* GPIO */
#define LOCOMO_GPD 0x90 /* GPIO direction */
#define LOCOMO_GPE 0x94 /* GPIO input enable */
#define LOCOMO_GPL 0x98 /* GPIO level */
-#define LOCOMO_GPO 0x9c /* GPIO out data setteing */
+#define LOCOMO_GPO 0x9c /* GPIO out data setting */
#define LOCOMO_GRIE 0xa0 /* GPIO rise detection */
#define LOCOMO_GFIE 0xa4 /* GPIO fall detection */
#define LOCOMO_GIS 0xa8 /* GPIO edge detection status */
@@ -96,6 +97,9 @@
#define LOCOMO_GPIO_DAC_SDATA LOCOMO_GPIO(10)
#define LOCOMO_GPIO_DAC_SCK LOCOMO_GPIO(11)
#define LOCOMO_GPIO_DAC_SLOAD LOCOMO_GPIO(12)
+#define LOCOMO_GPIO_CARD_DETECT LOCOMO_GPIO(13)
+#define LOCOMO_GPIO_WRITE_PROT LOCOMO_GPIO(14)
+#define LOCOMO_GPIO_CARD_POWER LOCOMO_GPIO(15)
/* Start the definitions of the devices. Each device has an initial
* base address and a series of offsets from that base address. */
@@ -122,7 +126,7 @@
/* Audio controller */
#define LOCOMO_AUDIO 0x54
#define LOCOMO_ACC 0x00 /* Audio clock */
-#define LOCOMO_PAIF 0x7C /* PCM audio interface */
+#define LOCOMO_PAIF 0xD0 /* PCM audio interface */
/* Audio clock */
#define LOCOMO_ACC_XON 0x80
#define LOCOMO_ACC_XEN 0x40
@@ -162,7 +166,7 @@
#define LOCOMO_DEVID_AUDIO 3
#define LOCOMO_DEVID_LED 4
#define LOCOMO_DEVID_UART 5
-#define LOCOMO_DEVID_SPI 6
+#define LOCOMO_DEVID_SPI 6
struct locomo_dev {
struct device dev;
@@ -204,7 +208,6 @@
int locomo_gpio_read_output(struct device *dev, unsigned int bits);
void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set);
-
/* M62332 control function */
void locomo_m62332_senddata(struct locomo_dev *ldev, unsigned int dac_data, int channel);