|  | /* | 
|  | *      Davicom DM9000 Fast Ethernet driver for Linux. | 
|  | * 	Copyright (C) 1997  Sten Wang | 
|  | * | 
|  | * 	This program is free software; you can redistribute it and/or | 
|  | * 	modify it under the terms of the GNU General Public License | 
|  | * 	as published by the Free Software Foundation; either version 2 | 
|  | * 	of the License, or (at your option) any later version. | 
|  | * | 
|  | * 	This program is distributed in the hope that it will be useful, | 
|  | * 	but WITHOUT ANY WARRANTY; without even the implied warranty of | 
|  | * 	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the | 
|  | * 	GNU General Public License for more details. | 
|  | * | 
|  | * (C) Copyright 1997-1998 DAVICOM Semiconductor,Inc. All Rights Reserved. | 
|  | * | 
|  | * Additional updates, Copyright: | 
|  | *	Ben Dooks <ben@simtec.co.uk> | 
|  | *	Sascha Hauer <s.hauer@pengutronix.de> | 
|  | */ | 
|  |  | 
|  | #include <linux/module.h> | 
|  | #include <linux/ioport.h> | 
|  | #include <linux/netdevice.h> | 
|  | #include <linux/etherdevice.h> | 
|  | #include <linux/init.h> | 
|  | #include <linux/interrupt.h> | 
|  | #include <linux/skbuff.h> | 
|  | #include <linux/spinlock.h> | 
|  | #include <linux/crc32.h> | 
|  | #include <linux/mii.h> | 
|  | #include <linux/ethtool.h> | 
|  | #include <linux/dm9000.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/platform_device.h> | 
|  | #include <linux/irq.h> | 
|  | #include <linux/slab.h> | 
|  |  | 
|  | #include <asm/delay.h> | 
|  | #include <asm/irq.h> | 
|  | #include <asm/io.h> | 
|  |  | 
|  | #include "dm9000.h" | 
|  |  | 
|  | /* Board/System/Debug information/definition ---------------- */ | 
|  |  | 
|  | #define DM9000_PHY		0x40	/* PHY address 0x01 */ | 
|  |  | 
|  | #define CARDNAME	"dm9000" | 
|  | #define DRV_VERSION	"1.31" | 
|  |  | 
|  | /* | 
|  | * Transmit timeout, default 5 seconds. | 
|  | */ | 
|  | static int watchdog = 5000; | 
|  | module_param(watchdog, int, 0400); | 
|  | MODULE_PARM_DESC(watchdog, "transmit timeout in milliseconds"); | 
|  |  | 
|  | /* | 
|  | * Debug messages level | 
|  | */ | 
|  | static int debug; | 
|  | module_param(debug, int, 0644); | 
|  | MODULE_PARM_DESC(debug, "dm9000 debug level (0-4)"); | 
|  |  | 
|  | /* DM9000 register address locking. | 
|  | * | 
|  | * The DM9000 uses an address register to control where data written | 
|  | * to the data register goes. This means that the address register | 
|  | * must be preserved over interrupts or similar calls. | 
|  | * | 
|  | * During interrupt and other critical calls, a spinlock is used to | 
|  | * protect the system, but the calls themselves save the address | 
|  | * in the address register in case they are interrupting another | 
|  | * access to the device. | 
|  | * | 
|  | * For general accesses a lock is provided so that calls which are | 
|  | * allowed to sleep are serialised so that the address register does | 
|  | * not need to be saved. This lock also serves to serialise access | 
|  | * to the EEPROM and PHY access registers which are shared between | 
|  | * these two devices. | 
|  | */ | 
|  |  | 
|  | /* The driver supports the original DM9000E, and now the two newer | 
|  | * devices, DM9000A and DM9000B. | 
|  | */ | 
|  |  | 
|  | enum dm9000_type { | 
|  | TYPE_DM9000E,	/* original DM9000 */ | 
|  | TYPE_DM9000A, | 
|  | TYPE_DM9000B | 
|  | }; | 
|  |  | 
|  | /* Structure/enum declaration ------------------------------- */ | 
|  | typedef struct board_info { | 
|  |  | 
|  | void __iomem	*io_addr;	/* Register I/O base address */ | 
|  | void __iomem	*io_data;	/* Data I/O address */ | 
|  | u16		 irq;		/* IRQ */ | 
|  |  | 
|  | u16		tx_pkt_cnt; | 
|  | u16		queue_pkt_len; | 
|  | u16		queue_start_addr; | 
|  | u16		queue_ip_summed; | 
|  | u16		dbug_cnt; | 
|  | u8		io_mode;		/* 0:word, 2:byte */ | 
|  | u8		phy_addr; | 
|  | u8		imr_all; | 
|  |  | 
|  | unsigned int	flags; | 
|  | unsigned int	in_suspend :1; | 
|  | unsigned int	wake_supported :1; | 
|  |  | 
|  | enum dm9000_type type; | 
|  |  | 
|  | void (*inblk)(void __iomem *port, void *data, int length); | 
|  | void (*outblk)(void __iomem *port, void *data, int length); | 
|  | void (*dumpblk)(void __iomem *port, int length); | 
|  |  | 
|  | struct device	*dev;	     /* parent device */ | 
|  |  | 
|  | struct resource	*addr_res;   /* resources found */ | 
|  | struct resource *data_res; | 
|  | struct resource	*addr_req;   /* resources requested */ | 
|  | struct resource *data_req; | 
|  | struct resource *irq_res; | 
|  |  | 
|  | int		 irq_wake; | 
|  |  | 
|  | struct mutex	 addr_lock;	/* phy and eeprom access lock */ | 
|  |  | 
|  | struct delayed_work phy_poll; | 
|  | struct net_device  *ndev; | 
|  |  | 
|  | spinlock_t	lock; | 
|  |  | 
|  | struct mii_if_info mii; | 
|  | u32		msg_enable; | 
|  | u32		wake_state; | 
|  |  | 
|  | int		ip_summed; | 
|  | } board_info_t; | 
|  |  | 
|  | /* debug code */ | 
|  |  | 
|  | #define dm9000_dbg(db, lev, msg...) do {		\ | 
|  | if ((lev) < debug) {				\ | 
|  | dev_dbg(db->dev, msg);			\ | 
|  | }						\ | 
|  | } while (0) | 
|  |  | 
|  | static inline board_info_t *to_dm9000_board(struct net_device *dev) | 
|  | { | 
|  | return netdev_priv(dev); | 
|  | } | 
|  |  | 
|  | /* DM9000 network board routine ---------------------------- */ | 
|  |  | 
|  | static void | 
|  | dm9000_reset(board_info_t * db) | 
|  | { | 
|  | dev_dbg(db->dev, "resetting device\n"); | 
|  |  | 
|  | /* RESET device */ | 
|  | writeb(DM9000_NCR, db->io_addr); | 
|  | udelay(200); | 
|  | writeb(NCR_RST, db->io_data); | 
|  | udelay(200); | 
|  | } | 
|  |  | 
|  | /* | 
|  | *   Read a byte from I/O port | 
|  | */ | 
|  | static u8 | 
|  | ior(board_info_t * db, int reg) | 
|  | { | 
|  | writeb(reg, db->io_addr); | 
|  | return readb(db->io_data); | 
|  | } | 
|  |  | 
|  | /* | 
|  | *   Write a byte to I/O port | 
|  | */ | 
|  |  | 
|  | static void | 
|  | iow(board_info_t * db, int reg, int value) | 
|  | { | 
|  | writeb(reg, db->io_addr); | 
|  | writeb(value, db->io_data); | 
|  | } | 
|  |  | 
|  | /* routines for sending block to chip */ | 
|  |  | 
|  | static void dm9000_outblk_8bit(void __iomem *reg, void *data, int count) | 
|  | { | 
|  | writesb(reg, data, count); | 
|  | } | 
|  |  | 
|  | static void dm9000_outblk_16bit(void __iomem *reg, void *data, int count) | 
|  | { | 
|  | writesw(reg, data, (count+1) >> 1); | 
|  | } | 
|  |  | 
|  | static void dm9000_outblk_32bit(void __iomem *reg, void *data, int count) | 
|  | { | 
|  | writesl(reg, data, (count+3) >> 2); | 
|  | } | 
|  |  | 
|  | /* input block from chip to memory */ | 
|  |  | 
|  | static void dm9000_inblk_8bit(void __iomem *reg, void *data, int count) | 
|  | { | 
|  | readsb(reg, data, count); | 
|  | } | 
|  |  | 
|  |  | 
|  | static void dm9000_inblk_16bit(void __iomem *reg, void *data, int count) | 
|  | { | 
|  | readsw(reg, data, (count+1) >> 1); | 
|  | } | 
|  |  | 
|  | static void dm9000_inblk_32bit(void __iomem *reg, void *data, int count) | 
|  | { | 
|  | readsl(reg, data, (count+3) >> 2); | 
|  | } | 
|  |  | 
|  | /* dump block from chip to null */ | 
|  |  | 
|  | static void dm9000_dumpblk_8bit(void __iomem *reg, int count) | 
|  | { | 
|  | int i; | 
|  | int tmp; | 
|  |  | 
|  | for (i = 0; i < count; i++) | 
|  | tmp = readb(reg); | 
|  | } | 
|  |  | 
|  | static void dm9000_dumpblk_16bit(void __iomem *reg, int count) | 
|  | { | 
|  | int i; | 
|  | int tmp; | 
|  |  | 
|  | count = (count + 1) >> 1; | 
|  |  | 
|  | for (i = 0; i < count; i++) | 
|  | tmp = readw(reg); | 
|  | } | 
|  |  | 
|  | static void dm9000_dumpblk_32bit(void __iomem *reg, int count) | 
|  | { | 
|  | int i; | 
|  | int tmp; | 
|  |  | 
|  | count = (count + 3) >> 2; | 
|  |  | 
|  | for (i = 0; i < count; i++) | 
|  | tmp = readl(reg); | 
|  | } | 
|  |  | 
|  | /* dm9000_set_io | 
|  | * | 
|  | * select the specified set of io routines to use with the | 
|  | * device | 
|  | */ | 
|  |  | 
|  | static void dm9000_set_io(struct board_info *db, int byte_width) | 
|  | { | 
|  | /* use the size of the data resource to work out what IO | 
|  | * routines we want to use | 
|  | */ | 
|  |  | 
|  | switch (byte_width) { | 
|  | case 1: | 
|  | db->dumpblk = dm9000_dumpblk_8bit; | 
|  | db->outblk  = dm9000_outblk_8bit; | 
|  | db->inblk   = dm9000_inblk_8bit; | 
|  | break; | 
|  |  | 
|  |  | 
|  | case 3: | 
|  | dev_dbg(db->dev, ": 3 byte IO, falling back to 16bit\n"); | 
|  | case 2: | 
|  | db->dumpblk = dm9000_dumpblk_16bit; | 
|  | db->outblk  = dm9000_outblk_16bit; | 
|  | db->inblk   = dm9000_inblk_16bit; | 
|  | break; | 
|  |  | 
|  | case 4: | 
|  | default: | 
|  | db->dumpblk = dm9000_dumpblk_32bit; | 
|  | db->outblk  = dm9000_outblk_32bit; | 
|  | db->inblk   = dm9000_inblk_32bit; | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | static void dm9000_schedule_poll(board_info_t *db) | 
|  | { | 
|  | if (db->type == TYPE_DM9000E) | 
|  | schedule_delayed_work(&db->phy_poll, HZ * 2); | 
|  | } | 
|  |  | 
|  | static int dm9000_ioctl(struct net_device *dev, struct ifreq *req, int cmd) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  |  | 
|  | if (!netif_running(dev)) | 
|  | return -EINVAL; | 
|  |  | 
|  | return generic_mii_ioctl(&dm->mii, if_mii(req), cmd, NULL); | 
|  | } | 
|  |  | 
|  | static unsigned int | 
|  | dm9000_read_locked(board_info_t *db, int reg) | 
|  | { | 
|  | unsigned long flags; | 
|  | unsigned int ret; | 
|  |  | 
|  | spin_lock_irqsave(&db->lock, flags); | 
|  | ret = ior(db, reg); | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int dm9000_wait_eeprom(board_info_t *db) | 
|  | { | 
|  | unsigned int status; | 
|  | int timeout = 8;	/* wait max 8msec */ | 
|  |  | 
|  | /* The DM9000 data sheets say we should be able to | 
|  | * poll the ERRE bit in EPCR to wait for the EEPROM | 
|  | * operation. From testing several chips, this bit | 
|  | * does not seem to work. | 
|  | * | 
|  | * We attempt to use the bit, but fall back to the | 
|  | * timeout (which is why we do not return an error | 
|  | * on expiry) to say that the EEPROM operation has | 
|  | * completed. | 
|  | */ | 
|  |  | 
|  | while (1) { | 
|  | status = dm9000_read_locked(db, DM9000_EPCR); | 
|  |  | 
|  | if ((status & EPCR_ERRE) == 0) | 
|  | break; | 
|  |  | 
|  | msleep(1); | 
|  |  | 
|  | if (timeout-- < 0) { | 
|  | dev_dbg(db->dev, "timeout waiting EEPROM\n"); | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* | 
|  | *  Read a word data from EEPROM | 
|  | */ | 
|  | static void | 
|  | dm9000_read_eeprom(board_info_t *db, int offset, u8 *to) | 
|  | { | 
|  | unsigned long flags; | 
|  |  | 
|  | if (db->flags & DM9000_PLATF_NO_EEPROM) { | 
|  | to[0] = 0xff; | 
|  | to[1] = 0xff; | 
|  | return; | 
|  | } | 
|  |  | 
|  | mutex_lock(&db->addr_lock); | 
|  |  | 
|  | spin_lock_irqsave(&db->lock, flags); | 
|  |  | 
|  | iow(db, DM9000_EPAR, offset); | 
|  | iow(db, DM9000_EPCR, EPCR_ERPRR); | 
|  |  | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  |  | 
|  | dm9000_wait_eeprom(db); | 
|  |  | 
|  | /* delay for at-least 150uS */ | 
|  | msleep(1); | 
|  |  | 
|  | spin_lock_irqsave(&db->lock, flags); | 
|  |  | 
|  | iow(db, DM9000_EPCR, 0x0); | 
|  |  | 
|  | to[0] = ior(db, DM9000_EPDRL); | 
|  | to[1] = ior(db, DM9000_EPDRH); | 
|  |  | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  |  | 
|  | mutex_unlock(&db->addr_lock); | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Write a word data to SROM | 
|  | */ | 
|  | static void | 
|  | dm9000_write_eeprom(board_info_t *db, int offset, u8 *data) | 
|  | { | 
|  | unsigned long flags; | 
|  |  | 
|  | if (db->flags & DM9000_PLATF_NO_EEPROM) | 
|  | return; | 
|  |  | 
|  | mutex_lock(&db->addr_lock); | 
|  |  | 
|  | spin_lock_irqsave(&db->lock, flags); | 
|  | iow(db, DM9000_EPAR, offset); | 
|  | iow(db, DM9000_EPDRH, data[1]); | 
|  | iow(db, DM9000_EPDRL, data[0]); | 
|  | iow(db, DM9000_EPCR, EPCR_WEP | EPCR_ERPRW); | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  |  | 
|  | dm9000_wait_eeprom(db); | 
|  |  | 
|  | mdelay(1);	/* wait at least 150uS to clear */ | 
|  |  | 
|  | spin_lock_irqsave(&db->lock, flags); | 
|  | iow(db, DM9000_EPCR, 0); | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  |  | 
|  | mutex_unlock(&db->addr_lock); | 
|  | } | 
|  |  | 
|  | /* ethtool ops */ | 
|  |  | 
|  | static void dm9000_get_drvinfo(struct net_device *dev, | 
|  | struct ethtool_drvinfo *info) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  |  | 
|  | strcpy(info->driver, CARDNAME); | 
|  | strcpy(info->version, DRV_VERSION); | 
|  | strcpy(info->bus_info, to_platform_device(dm->dev)->name); | 
|  | } | 
|  |  | 
|  | static u32 dm9000_get_msglevel(struct net_device *dev) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  |  | 
|  | return dm->msg_enable; | 
|  | } | 
|  |  | 
|  | static void dm9000_set_msglevel(struct net_device *dev, u32 value) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  |  | 
|  | dm->msg_enable = value; | 
|  | } | 
|  |  | 
|  | static int dm9000_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  |  | 
|  | mii_ethtool_gset(&dm->mii, cmd); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int dm9000_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  |  | 
|  | return mii_ethtool_sset(&dm->mii, cmd); | 
|  | } | 
|  |  | 
|  | static int dm9000_nway_reset(struct net_device *dev) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  | return mii_nway_restart(&dm->mii); | 
|  | } | 
|  |  | 
|  | static int dm9000_set_features(struct net_device *dev, | 
|  | netdev_features_t features) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  | netdev_features_t changed = dev->features ^ features; | 
|  | unsigned long flags; | 
|  |  | 
|  | if (!(changed & NETIF_F_RXCSUM)) | 
|  | return 0; | 
|  |  | 
|  | spin_lock_irqsave(&dm->lock, flags); | 
|  | iow(dm, DM9000_RCSR, (features & NETIF_F_RXCSUM) ? RCSR_CSUM : 0); | 
|  | spin_unlock_irqrestore(&dm->lock, flags); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static u32 dm9000_get_link(struct net_device *dev) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  | u32 ret; | 
|  |  | 
|  | if (dm->flags & DM9000_PLATF_EXT_PHY) | 
|  | ret = mii_link_ok(&dm->mii); | 
|  | else | 
|  | ret = dm9000_read_locked(dm, DM9000_NSR) & NSR_LINKST ? 1 : 0; | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | #define DM_EEPROM_MAGIC		(0x444D394B) | 
|  |  | 
|  | static int dm9000_get_eeprom_len(struct net_device *dev) | 
|  | { | 
|  | return 128; | 
|  | } | 
|  |  | 
|  | static int dm9000_get_eeprom(struct net_device *dev, | 
|  | struct ethtool_eeprom *ee, u8 *data) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  | int offset = ee->offset; | 
|  | int len = ee->len; | 
|  | int i; | 
|  |  | 
|  | /* EEPROM access is aligned to two bytes */ | 
|  |  | 
|  | if ((len & 1) != 0 || (offset & 1) != 0) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (dm->flags & DM9000_PLATF_NO_EEPROM) | 
|  | return -ENOENT; | 
|  |  | 
|  | ee->magic = DM_EEPROM_MAGIC; | 
|  |  | 
|  | for (i = 0; i < len; i += 2) | 
|  | dm9000_read_eeprom(dm, (offset + i) / 2, data + i); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int dm9000_set_eeprom(struct net_device *dev, | 
|  | struct ethtool_eeprom *ee, u8 *data) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  | int offset = ee->offset; | 
|  | int len = ee->len; | 
|  | int done; | 
|  |  | 
|  | /* EEPROM access is aligned to two bytes */ | 
|  |  | 
|  | if (dm->flags & DM9000_PLATF_NO_EEPROM) | 
|  | return -ENOENT; | 
|  |  | 
|  | if (ee->magic != DM_EEPROM_MAGIC) | 
|  | return -EINVAL; | 
|  |  | 
|  | while (len > 0) { | 
|  | if (len & 1 || offset & 1) { | 
|  | int which = offset & 1; | 
|  | u8 tmp[2]; | 
|  |  | 
|  | dm9000_read_eeprom(dm, offset / 2, tmp); | 
|  | tmp[which] = *data; | 
|  | dm9000_write_eeprom(dm, offset / 2, tmp); | 
|  |  | 
|  | done = 1; | 
|  | } else { | 
|  | dm9000_write_eeprom(dm, offset / 2, data); | 
|  | done = 2; | 
|  | } | 
|  |  | 
|  | data += done; | 
|  | offset += done; | 
|  | len -= done; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void dm9000_get_wol(struct net_device *dev, struct ethtool_wolinfo *w) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  |  | 
|  | memset(w, 0, sizeof(struct ethtool_wolinfo)); | 
|  |  | 
|  | /* note, we could probably support wake-phy too */ | 
|  | w->supported = dm->wake_supported ? WAKE_MAGIC : 0; | 
|  | w->wolopts = dm->wake_state; | 
|  | } | 
|  |  | 
|  | static int dm9000_set_wol(struct net_device *dev, struct ethtool_wolinfo *w) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  | unsigned long flags; | 
|  | u32 opts = w->wolopts; | 
|  | u32 wcr = 0; | 
|  |  | 
|  | if (!dm->wake_supported) | 
|  | return -EOPNOTSUPP; | 
|  |  | 
|  | if (opts & ~WAKE_MAGIC) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (opts & WAKE_MAGIC) | 
|  | wcr |= WCR_MAGICEN; | 
|  |  | 
|  | mutex_lock(&dm->addr_lock); | 
|  |  | 
|  | spin_lock_irqsave(&dm->lock, flags); | 
|  | iow(dm, DM9000_WCR, wcr); | 
|  | spin_unlock_irqrestore(&dm->lock, flags); | 
|  |  | 
|  | mutex_unlock(&dm->addr_lock); | 
|  |  | 
|  | if (dm->wake_state != opts) { | 
|  | /* change in wol state, update IRQ state */ | 
|  |  | 
|  | if (!dm->wake_state) | 
|  | irq_set_irq_wake(dm->irq_wake, 1); | 
|  | else if (dm->wake_state && !opts) | 
|  | irq_set_irq_wake(dm->irq_wake, 0); | 
|  | } | 
|  |  | 
|  | dm->wake_state = opts; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct ethtool_ops dm9000_ethtool_ops = { | 
|  | .get_drvinfo		= dm9000_get_drvinfo, | 
|  | .get_settings		= dm9000_get_settings, | 
|  | .set_settings		= dm9000_set_settings, | 
|  | .get_msglevel		= dm9000_get_msglevel, | 
|  | .set_msglevel		= dm9000_set_msglevel, | 
|  | .nway_reset		= dm9000_nway_reset, | 
|  | .get_link		= dm9000_get_link, | 
|  | .get_wol		= dm9000_get_wol, | 
|  | .set_wol		= dm9000_set_wol, | 
|  | .get_eeprom_len		= dm9000_get_eeprom_len, | 
|  | .get_eeprom		= dm9000_get_eeprom, | 
|  | .set_eeprom		= dm9000_set_eeprom, | 
|  | }; | 
|  |  | 
|  | static void dm9000_show_carrier(board_info_t *db, | 
|  | unsigned carrier, unsigned nsr) | 
|  | { | 
|  | struct net_device *ndev = db->ndev; | 
|  | unsigned ncr = dm9000_read_locked(db, DM9000_NCR); | 
|  |  | 
|  | if (carrier) | 
|  | dev_info(db->dev, "%s: link up, %dMbps, %s-duplex, no LPA\n", | 
|  | ndev->name, (nsr & NSR_SPEED) ? 10 : 100, | 
|  | (ncr & NCR_FDX) ? "full" : "half"); | 
|  | else | 
|  | dev_info(db->dev, "%s: link down\n", ndev->name); | 
|  | } | 
|  |  | 
|  | static void | 
|  | dm9000_poll_work(struct work_struct *w) | 
|  | { | 
|  | struct delayed_work *dw = to_delayed_work(w); | 
|  | board_info_t *db = container_of(dw, board_info_t, phy_poll); | 
|  | struct net_device *ndev = db->ndev; | 
|  |  | 
|  | if (db->flags & DM9000_PLATF_SIMPLE_PHY && | 
|  | !(db->flags & DM9000_PLATF_EXT_PHY)) { | 
|  | unsigned nsr = dm9000_read_locked(db, DM9000_NSR); | 
|  | unsigned old_carrier = netif_carrier_ok(ndev) ? 1 : 0; | 
|  | unsigned new_carrier; | 
|  |  | 
|  | new_carrier = (nsr & NSR_LINKST) ? 1 : 0; | 
|  |  | 
|  | if (old_carrier != new_carrier) { | 
|  | if (netif_msg_link(db)) | 
|  | dm9000_show_carrier(db, new_carrier, nsr); | 
|  |  | 
|  | if (!new_carrier) | 
|  | netif_carrier_off(ndev); | 
|  | else | 
|  | netif_carrier_on(ndev); | 
|  | } | 
|  | } else | 
|  | mii_check_media(&db->mii, netif_msg_link(db), 0); | 
|  |  | 
|  | if (netif_running(ndev)) | 
|  | dm9000_schedule_poll(db); | 
|  | } | 
|  |  | 
|  | /* dm9000_release_board | 
|  | * | 
|  | * release a board, and any mapped resources | 
|  | */ | 
|  |  | 
|  | static void | 
|  | dm9000_release_board(struct platform_device *pdev, struct board_info *db) | 
|  | { | 
|  | /* unmap our resources */ | 
|  |  | 
|  | iounmap(db->io_addr); | 
|  | iounmap(db->io_data); | 
|  |  | 
|  | /* release the resources */ | 
|  |  | 
|  | release_resource(db->data_req); | 
|  | kfree(db->data_req); | 
|  |  | 
|  | release_resource(db->addr_req); | 
|  | kfree(db->addr_req); | 
|  | } | 
|  |  | 
|  | static unsigned char dm9000_type_to_char(enum dm9000_type type) | 
|  | { | 
|  | switch (type) { | 
|  | case TYPE_DM9000E: return 'e'; | 
|  | case TYPE_DM9000A: return 'a'; | 
|  | case TYPE_DM9000B: return 'b'; | 
|  | } | 
|  |  | 
|  | return '?'; | 
|  | } | 
|  |  | 
|  | /* | 
|  | *  Set DM9000 multicast address | 
|  | */ | 
|  | static void | 
|  | dm9000_hash_table_unlocked(struct net_device *dev) | 
|  | { | 
|  | board_info_t *db = netdev_priv(dev); | 
|  | struct netdev_hw_addr *ha; | 
|  | int i, oft; | 
|  | u32 hash_val; | 
|  | u16 hash_table[4]; | 
|  | u8 rcr = RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN; | 
|  |  | 
|  | dm9000_dbg(db, 1, "entering %s\n", __func__); | 
|  |  | 
|  | for (i = 0, oft = DM9000_PAR; i < 6; i++, oft++) | 
|  | iow(db, oft, dev->dev_addr[i]); | 
|  |  | 
|  | /* Clear Hash Table */ | 
|  | for (i = 0; i < 4; i++) | 
|  | hash_table[i] = 0x0; | 
|  |  | 
|  | /* broadcast address */ | 
|  | hash_table[3] = 0x8000; | 
|  |  | 
|  | if (dev->flags & IFF_PROMISC) | 
|  | rcr |= RCR_PRMSC; | 
|  |  | 
|  | if (dev->flags & IFF_ALLMULTI) | 
|  | rcr |= RCR_ALL; | 
|  |  | 
|  | /* the multicast address in Hash Table : 64 bits */ | 
|  | netdev_for_each_mc_addr(ha, dev) { | 
|  | hash_val = ether_crc_le(6, ha->addr) & 0x3f; | 
|  | hash_table[hash_val / 16] |= (u16) 1 << (hash_val % 16); | 
|  | } | 
|  |  | 
|  | /* Write the hash table to MAC MD table */ | 
|  | for (i = 0, oft = DM9000_MAR; i < 4; i++) { | 
|  | iow(db, oft++, hash_table[i]); | 
|  | iow(db, oft++, hash_table[i] >> 8); | 
|  | } | 
|  |  | 
|  | iow(db, DM9000_RCR, rcr); | 
|  | } | 
|  |  | 
|  | static void | 
|  | dm9000_hash_table(struct net_device *dev) | 
|  | { | 
|  | board_info_t *db = netdev_priv(dev); | 
|  | unsigned long flags; | 
|  |  | 
|  | spin_lock_irqsave(&db->lock, flags); | 
|  | dm9000_hash_table_unlocked(dev); | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Initialize dm9000 board | 
|  | */ | 
|  | static void | 
|  | dm9000_init_dm9000(struct net_device *dev) | 
|  | { | 
|  | board_info_t *db = netdev_priv(dev); | 
|  | unsigned int imr; | 
|  | unsigned int ncr; | 
|  |  | 
|  | dm9000_dbg(db, 1, "entering %s\n", __func__); | 
|  |  | 
|  | /* I/O mode */ | 
|  | db->io_mode = ior(db, DM9000_ISR) >> 6;	/* ISR bit7:6 keeps I/O mode */ | 
|  |  | 
|  | /* Checksum mode */ | 
|  | if (dev->hw_features & NETIF_F_RXCSUM) | 
|  | iow(db, DM9000_RCSR, | 
|  | (dev->features & NETIF_F_RXCSUM) ? RCSR_CSUM : 0); | 
|  |  | 
|  | iow(db, DM9000_GPCR, GPCR_GEP_CNTL);	/* Let GPIO0 output */ | 
|  |  | 
|  | ncr = (db->flags & DM9000_PLATF_EXT_PHY) ? NCR_EXT_PHY : 0; | 
|  |  | 
|  | /* if wol is needed, then always set NCR_WAKEEN otherwise we end | 
|  | * up dumping the wake events if we disable this. There is already | 
|  | * a wake-mask in DM9000_WCR */ | 
|  | if (db->wake_supported) | 
|  | ncr |= NCR_WAKEEN; | 
|  |  | 
|  | iow(db, DM9000_NCR, ncr); | 
|  |  | 
|  | /* Program operating register */ | 
|  | iow(db, DM9000_TCR, 0);	        /* TX Polling clear */ | 
|  | iow(db, DM9000_BPTR, 0x3f);	/* Less 3Kb, 200us */ | 
|  | iow(db, DM9000_FCR, 0xff);	/* Flow Control */ | 
|  | iow(db, DM9000_SMCR, 0);        /* Special Mode */ | 
|  | /* clear TX status */ | 
|  | iow(db, DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END); | 
|  | iow(db, DM9000_ISR, ISR_CLR_STATUS); /* Clear interrupt status */ | 
|  |  | 
|  | /* Set address filter table */ | 
|  | dm9000_hash_table_unlocked(dev); | 
|  |  | 
|  | imr = IMR_PAR | IMR_PTM | IMR_PRM; | 
|  | if (db->type != TYPE_DM9000E) | 
|  | imr |= IMR_LNKCHNG; | 
|  |  | 
|  | db->imr_all = imr; | 
|  |  | 
|  | /* Enable TX/RX interrupt mask */ | 
|  | iow(db, DM9000_IMR, imr); | 
|  |  | 
|  | /* Init Driver variable */ | 
|  | db->tx_pkt_cnt = 0; | 
|  | db->queue_pkt_len = 0; | 
|  | dev->trans_start = jiffies; | 
|  | } | 
|  |  | 
|  | /* Our watchdog timed out. Called by the networking layer */ | 
|  | static void dm9000_timeout(struct net_device *dev) | 
|  | { | 
|  | board_info_t *db = netdev_priv(dev); | 
|  | u8 reg_save; | 
|  | unsigned long flags; | 
|  |  | 
|  | /* Save previous register address */ | 
|  | spin_lock_irqsave(&db->lock, flags); | 
|  | reg_save = readb(db->io_addr); | 
|  |  | 
|  | netif_stop_queue(dev); | 
|  | dm9000_reset(db); | 
|  | dm9000_init_dm9000(dev); | 
|  | /* We can accept TX packets again */ | 
|  | dev->trans_start = jiffies; /* prevent tx timeout */ | 
|  | netif_wake_queue(dev); | 
|  |  | 
|  | /* Restore previous register address */ | 
|  | writeb(reg_save, db->io_addr); | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  | } | 
|  |  | 
|  | static void dm9000_send_packet(struct net_device *dev, | 
|  | int ip_summed, | 
|  | u16 pkt_len) | 
|  | { | 
|  | board_info_t *dm = to_dm9000_board(dev); | 
|  |  | 
|  | /* The DM9000 is not smart enough to leave fragmented packets alone. */ | 
|  | if (dm->ip_summed != ip_summed) { | 
|  | if (ip_summed == CHECKSUM_NONE) | 
|  | iow(dm, DM9000_TCCR, 0); | 
|  | else | 
|  | iow(dm, DM9000_TCCR, TCCR_IP | TCCR_UDP | TCCR_TCP); | 
|  | dm->ip_summed = ip_summed; | 
|  | } | 
|  |  | 
|  | /* Set TX length to DM9000 */ | 
|  | iow(dm, DM9000_TXPLL, pkt_len); | 
|  | iow(dm, DM9000_TXPLH, pkt_len >> 8); | 
|  |  | 
|  | /* Issue TX polling command */ | 
|  | iow(dm, DM9000_TCR, TCR_TXREQ);	/* Cleared after TX complete */ | 
|  | } | 
|  |  | 
|  | /* | 
|  | *  Hardware start transmission. | 
|  | *  Send a packet to media from the upper layer. | 
|  | */ | 
|  | static int | 
|  | dm9000_start_xmit(struct sk_buff *skb, struct net_device *dev) | 
|  | { | 
|  | unsigned long flags; | 
|  | board_info_t *db = netdev_priv(dev); | 
|  |  | 
|  | dm9000_dbg(db, 3, "%s:\n", __func__); | 
|  |  | 
|  | if (db->tx_pkt_cnt > 1) | 
|  | return NETDEV_TX_BUSY; | 
|  |  | 
|  | spin_lock_irqsave(&db->lock, flags); | 
|  |  | 
|  | /* Move data to DM9000 TX RAM */ | 
|  | writeb(DM9000_MWCMD, db->io_addr); | 
|  |  | 
|  | (db->outblk)(db->io_data, skb->data, skb->len); | 
|  | dev->stats.tx_bytes += skb->len; | 
|  |  | 
|  | db->tx_pkt_cnt++; | 
|  | /* TX control: First packet immediately send, second packet queue */ | 
|  | if (db->tx_pkt_cnt == 1) { | 
|  | dm9000_send_packet(dev, skb->ip_summed, skb->len); | 
|  | } else { | 
|  | /* Second packet */ | 
|  | db->queue_pkt_len = skb->len; | 
|  | db->queue_ip_summed = skb->ip_summed; | 
|  | netif_stop_queue(dev); | 
|  | } | 
|  |  | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  |  | 
|  | /* free this SKB */ | 
|  | dev_kfree_skb(skb); | 
|  |  | 
|  | return NETDEV_TX_OK; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * DM9000 interrupt handler | 
|  | * receive the packet to upper layer, free the transmitted packet | 
|  | */ | 
|  |  | 
|  | static void dm9000_tx_done(struct net_device *dev, board_info_t *db) | 
|  | { | 
|  | int tx_status = ior(db, DM9000_NSR);	/* Got TX status */ | 
|  |  | 
|  | if (tx_status & (NSR_TX2END | NSR_TX1END)) { | 
|  | /* One packet sent complete */ | 
|  | db->tx_pkt_cnt--; | 
|  | dev->stats.tx_packets++; | 
|  |  | 
|  | if (netif_msg_tx_done(db)) | 
|  | dev_dbg(db->dev, "tx done, NSR %02x\n", tx_status); | 
|  |  | 
|  | /* Queue packet check & send */ | 
|  | if (db->tx_pkt_cnt > 0) | 
|  | dm9000_send_packet(dev, db->queue_ip_summed, | 
|  | db->queue_pkt_len); | 
|  | netif_wake_queue(dev); | 
|  | } | 
|  | } | 
|  |  | 
|  | struct dm9000_rxhdr { | 
|  | u8	RxPktReady; | 
|  | u8	RxStatus; | 
|  | __le16	RxLen; | 
|  | } __packed; | 
|  |  | 
|  | /* | 
|  | *  Received a packet and pass to upper layer | 
|  | */ | 
|  | static void | 
|  | dm9000_rx(struct net_device *dev) | 
|  | { | 
|  | board_info_t *db = netdev_priv(dev); | 
|  | struct dm9000_rxhdr rxhdr; | 
|  | struct sk_buff *skb; | 
|  | u8 rxbyte, *rdptr; | 
|  | bool GoodPacket; | 
|  | int RxLen; | 
|  |  | 
|  | /* Check packet ready or not */ | 
|  | do { | 
|  | ior(db, DM9000_MRCMDX);	/* Dummy read */ | 
|  |  | 
|  | /* Get most updated data */ | 
|  | rxbyte = readb(db->io_data); | 
|  |  | 
|  | /* Status check: this byte must be 0 or 1 */ | 
|  | if (rxbyte & DM9000_PKT_ERR) { | 
|  | dev_warn(db->dev, "status check fail: %d\n", rxbyte); | 
|  | iow(db, DM9000_RCR, 0x00);	/* Stop Device */ | 
|  | iow(db, DM9000_ISR, IMR_PAR);	/* Stop INT request */ | 
|  | return; | 
|  | } | 
|  |  | 
|  | if (!(rxbyte & DM9000_PKT_RDY)) | 
|  | return; | 
|  |  | 
|  | /* A packet ready now  & Get status/length */ | 
|  | GoodPacket = true; | 
|  | writeb(DM9000_MRCMD, db->io_addr); | 
|  |  | 
|  | (db->inblk)(db->io_data, &rxhdr, sizeof(rxhdr)); | 
|  |  | 
|  | RxLen = le16_to_cpu(rxhdr.RxLen); | 
|  |  | 
|  | if (netif_msg_rx_status(db)) | 
|  | dev_dbg(db->dev, "RX: status %02x, length %04x\n", | 
|  | rxhdr.RxStatus, RxLen); | 
|  |  | 
|  | /* Packet Status check */ | 
|  | if (RxLen < 0x40) { | 
|  | GoodPacket = false; | 
|  | if (netif_msg_rx_err(db)) | 
|  | dev_dbg(db->dev, "RX: Bad Packet (runt)\n"); | 
|  | } | 
|  |  | 
|  | if (RxLen > DM9000_PKT_MAX) { | 
|  | dev_dbg(db->dev, "RST: RX Len:%x\n", RxLen); | 
|  | } | 
|  |  | 
|  | /* rxhdr.RxStatus is identical to RSR register. */ | 
|  | if (rxhdr.RxStatus & (RSR_FOE | RSR_CE | RSR_AE | | 
|  | RSR_PLE | RSR_RWTO | | 
|  | RSR_LCS | RSR_RF)) { | 
|  | GoodPacket = false; | 
|  | if (rxhdr.RxStatus & RSR_FOE) { | 
|  | if (netif_msg_rx_err(db)) | 
|  | dev_dbg(db->dev, "fifo error\n"); | 
|  | dev->stats.rx_fifo_errors++; | 
|  | } | 
|  | if (rxhdr.RxStatus & RSR_CE) { | 
|  | if (netif_msg_rx_err(db)) | 
|  | dev_dbg(db->dev, "crc error\n"); | 
|  | dev->stats.rx_crc_errors++; | 
|  | } | 
|  | if (rxhdr.RxStatus & RSR_RF) { | 
|  | if (netif_msg_rx_err(db)) | 
|  | dev_dbg(db->dev, "length error\n"); | 
|  | dev->stats.rx_length_errors++; | 
|  | } | 
|  | } | 
|  |  | 
|  | /* Move data from DM9000 */ | 
|  | if (GoodPacket && | 
|  | ((skb = netdev_alloc_skb(dev, RxLen + 4)) != NULL)) { | 
|  | skb_reserve(skb, 2); | 
|  | rdptr = (u8 *) skb_put(skb, RxLen - 4); | 
|  |  | 
|  | /* Read received packet from RX SRAM */ | 
|  |  | 
|  | (db->inblk)(db->io_data, rdptr, RxLen); | 
|  | dev->stats.rx_bytes += RxLen; | 
|  |  | 
|  | /* Pass to upper layer */ | 
|  | skb->protocol = eth_type_trans(skb, dev); | 
|  | if (dev->features & NETIF_F_RXCSUM) { | 
|  | if ((((rxbyte & 0x1c) << 3) & rxbyte) == 0) | 
|  | skb->ip_summed = CHECKSUM_UNNECESSARY; | 
|  | else | 
|  | skb_checksum_none_assert(skb); | 
|  | } | 
|  | netif_rx(skb); | 
|  | dev->stats.rx_packets++; | 
|  |  | 
|  | } else { | 
|  | /* need to dump the packet's data */ | 
|  |  | 
|  | (db->dumpblk)(db->io_data, RxLen); | 
|  | } | 
|  | } while (rxbyte & DM9000_PKT_RDY); | 
|  | } | 
|  |  | 
|  | static irqreturn_t dm9000_interrupt(int irq, void *dev_id) | 
|  | { | 
|  | struct net_device *dev = dev_id; | 
|  | board_info_t *db = netdev_priv(dev); | 
|  | int int_status; | 
|  | unsigned long flags; | 
|  | u8 reg_save; | 
|  |  | 
|  | dm9000_dbg(db, 3, "entering %s\n", __func__); | 
|  |  | 
|  | /* A real interrupt coming */ | 
|  |  | 
|  | /* holders of db->lock must always block IRQs */ | 
|  | spin_lock_irqsave(&db->lock, flags); | 
|  |  | 
|  | /* Save previous register address */ | 
|  | reg_save = readb(db->io_addr); | 
|  |  | 
|  | /* Disable all interrupts */ | 
|  | iow(db, DM9000_IMR, IMR_PAR); | 
|  |  | 
|  | /* Got DM9000 interrupt status */ | 
|  | int_status = ior(db, DM9000_ISR);	/* Got ISR */ | 
|  | iow(db, DM9000_ISR, int_status);	/* Clear ISR status */ | 
|  |  | 
|  | if (netif_msg_intr(db)) | 
|  | dev_dbg(db->dev, "interrupt status %02x\n", int_status); | 
|  |  | 
|  | /* Received the coming packet */ | 
|  | if (int_status & ISR_PRS) | 
|  | dm9000_rx(dev); | 
|  |  | 
|  | /* Trnasmit Interrupt check */ | 
|  | if (int_status & ISR_PTS) | 
|  | dm9000_tx_done(dev, db); | 
|  |  | 
|  | if (db->type != TYPE_DM9000E) { | 
|  | if (int_status & ISR_LNKCHNG) { | 
|  | /* fire a link-change request */ | 
|  | schedule_delayed_work(&db->phy_poll, 1); | 
|  | } | 
|  | } | 
|  |  | 
|  | /* Re-enable interrupt mask */ | 
|  | iow(db, DM9000_IMR, db->imr_all); | 
|  |  | 
|  | /* Restore previous register address */ | 
|  | writeb(reg_save, db->io_addr); | 
|  |  | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  |  | 
|  | return IRQ_HANDLED; | 
|  | } | 
|  |  | 
|  | static irqreturn_t dm9000_wol_interrupt(int irq, void *dev_id) | 
|  | { | 
|  | struct net_device *dev = dev_id; | 
|  | board_info_t *db = netdev_priv(dev); | 
|  | unsigned long flags; | 
|  | unsigned nsr, wcr; | 
|  |  | 
|  | spin_lock_irqsave(&db->lock, flags); | 
|  |  | 
|  | nsr = ior(db, DM9000_NSR); | 
|  | wcr = ior(db, DM9000_WCR); | 
|  |  | 
|  | dev_dbg(db->dev, "%s: NSR=0x%02x, WCR=0x%02x\n", __func__, nsr, wcr); | 
|  |  | 
|  | if (nsr & NSR_WAKEST) { | 
|  | /* clear, so we can avoid */ | 
|  | iow(db, DM9000_NSR, NSR_WAKEST); | 
|  |  | 
|  | if (wcr & WCR_LINKST) | 
|  | dev_info(db->dev, "wake by link status change\n"); | 
|  | if (wcr & WCR_SAMPLEST) | 
|  | dev_info(db->dev, "wake by sample packet\n"); | 
|  | if (wcr & WCR_MAGICST ) | 
|  | dev_info(db->dev, "wake by magic packet\n"); | 
|  | if (!(wcr & (WCR_LINKST | WCR_SAMPLEST | WCR_MAGICST))) | 
|  | dev_err(db->dev, "wake signalled with no reason? " | 
|  | "NSR=0x%02x, WSR=0x%02x\n", nsr, wcr); | 
|  |  | 
|  | } | 
|  |  | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  |  | 
|  | return (nsr & NSR_WAKEST) ? IRQ_HANDLED : IRQ_NONE; | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_NET_POLL_CONTROLLER | 
|  | /* | 
|  | *Used by netconsole | 
|  | */ | 
|  | static void dm9000_poll_controller(struct net_device *dev) | 
|  | { | 
|  | disable_irq(dev->irq); | 
|  | dm9000_interrupt(dev->irq, dev); | 
|  | enable_irq(dev->irq); | 
|  | } | 
|  | #endif | 
|  |  | 
|  | /* | 
|  | *  Open the interface. | 
|  | *  The interface is opened whenever "ifconfig" actives it. | 
|  | */ | 
|  | static int | 
|  | dm9000_open(struct net_device *dev) | 
|  | { | 
|  | board_info_t *db = netdev_priv(dev); | 
|  | unsigned long irqflags = db->irq_res->flags & IRQF_TRIGGER_MASK; | 
|  |  | 
|  | if (netif_msg_ifup(db)) | 
|  | dev_dbg(db->dev, "enabling %s\n", dev->name); | 
|  |  | 
|  | /* If there is no IRQ type specified, default to something that | 
|  | * may work, and tell the user that this is a problem */ | 
|  |  | 
|  | if (irqflags == IRQF_TRIGGER_NONE) | 
|  | dev_warn(db->dev, "WARNING: no IRQ resource flags set.\n"); | 
|  |  | 
|  | irqflags |= IRQF_SHARED; | 
|  |  | 
|  | /* GPIO0 on pre-activate PHY, Reg 1F is not set by reset */ | 
|  | iow(db, DM9000_GPR, 0);	/* REG_1F bit0 activate phyxcer */ | 
|  | mdelay(1); /* delay needs by DM9000B */ | 
|  |  | 
|  | /* Initialize DM9000 board */ | 
|  | dm9000_reset(db); | 
|  | dm9000_init_dm9000(dev); | 
|  |  | 
|  | if (request_irq(dev->irq, dm9000_interrupt, irqflags, dev->name, dev)) | 
|  | return -EAGAIN; | 
|  |  | 
|  | /* Init driver variable */ | 
|  | db->dbug_cnt = 0; | 
|  |  | 
|  | mii_check_media(&db->mii, netif_msg_link(db), 1); | 
|  | netif_start_queue(dev); | 
|  |  | 
|  | dm9000_schedule_poll(db); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Sleep, either by using msleep() or if we are suspending, then | 
|  | * use mdelay() to sleep. | 
|  | */ | 
|  | static void dm9000_msleep(board_info_t *db, unsigned int ms) | 
|  | { | 
|  | if (db->in_suspend) | 
|  | mdelay(ms); | 
|  | else | 
|  | msleep(ms); | 
|  | } | 
|  |  | 
|  | /* | 
|  | *   Read a word from phyxcer | 
|  | */ | 
|  | static int | 
|  | dm9000_phy_read(struct net_device *dev, int phy_reg_unused, int reg) | 
|  | { | 
|  | board_info_t *db = netdev_priv(dev); | 
|  | unsigned long flags; | 
|  | unsigned int reg_save; | 
|  | int ret; | 
|  |  | 
|  | mutex_lock(&db->addr_lock); | 
|  |  | 
|  | spin_lock_irqsave(&db->lock,flags); | 
|  |  | 
|  | /* Save previous register address */ | 
|  | reg_save = readb(db->io_addr); | 
|  |  | 
|  | /* Fill the phyxcer register into REG_0C */ | 
|  | iow(db, DM9000_EPAR, DM9000_PHY | reg); | 
|  |  | 
|  | iow(db, DM9000_EPCR, EPCR_ERPRR | EPCR_EPOS);	/* Issue phyxcer read command */ | 
|  |  | 
|  | writeb(reg_save, db->io_addr); | 
|  | spin_unlock_irqrestore(&db->lock,flags); | 
|  |  | 
|  | dm9000_msleep(db, 1);		/* Wait read complete */ | 
|  |  | 
|  | spin_lock_irqsave(&db->lock,flags); | 
|  | reg_save = readb(db->io_addr); | 
|  |  | 
|  | iow(db, DM9000_EPCR, 0x0);	/* Clear phyxcer read command */ | 
|  |  | 
|  | /* The read data keeps on REG_0D & REG_0E */ | 
|  | ret = (ior(db, DM9000_EPDRH) << 8) | ior(db, DM9000_EPDRL); | 
|  |  | 
|  | /* restore the previous address */ | 
|  | writeb(reg_save, db->io_addr); | 
|  | spin_unlock_irqrestore(&db->lock,flags); | 
|  |  | 
|  | mutex_unlock(&db->addr_lock); | 
|  |  | 
|  | dm9000_dbg(db, 5, "phy_read[%02x] -> %04x\n", reg, ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | /* | 
|  | *   Write a word to phyxcer | 
|  | */ | 
|  | static void | 
|  | dm9000_phy_write(struct net_device *dev, | 
|  | int phyaddr_unused, int reg, int value) | 
|  | { | 
|  | board_info_t *db = netdev_priv(dev); | 
|  | unsigned long flags; | 
|  | unsigned long reg_save; | 
|  |  | 
|  | dm9000_dbg(db, 5, "phy_write[%02x] = %04x\n", reg, value); | 
|  | mutex_lock(&db->addr_lock); | 
|  |  | 
|  | spin_lock_irqsave(&db->lock,flags); | 
|  |  | 
|  | /* Save previous register address */ | 
|  | reg_save = readb(db->io_addr); | 
|  |  | 
|  | /* Fill the phyxcer register into REG_0C */ | 
|  | iow(db, DM9000_EPAR, DM9000_PHY | reg); | 
|  |  | 
|  | /* Fill the written data into REG_0D & REG_0E */ | 
|  | iow(db, DM9000_EPDRL, value); | 
|  | iow(db, DM9000_EPDRH, value >> 8); | 
|  |  | 
|  | iow(db, DM9000_EPCR, EPCR_EPOS | EPCR_ERPRW);	/* Issue phyxcer write command */ | 
|  |  | 
|  | writeb(reg_save, db->io_addr); | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  |  | 
|  | dm9000_msleep(db, 1);		/* Wait write complete */ | 
|  |  | 
|  | spin_lock_irqsave(&db->lock,flags); | 
|  | reg_save = readb(db->io_addr); | 
|  |  | 
|  | iow(db, DM9000_EPCR, 0x0);	/* Clear phyxcer write command */ | 
|  |  | 
|  | /* restore the previous address */ | 
|  | writeb(reg_save, db->io_addr); | 
|  |  | 
|  | spin_unlock_irqrestore(&db->lock, flags); | 
|  | mutex_unlock(&db->addr_lock); | 
|  | } | 
|  |  | 
|  | static void | 
|  | dm9000_shutdown(struct net_device *dev) | 
|  | { | 
|  | board_info_t *db = netdev_priv(dev); | 
|  |  | 
|  | /* RESET device */ | 
|  | dm9000_phy_write(dev, 0, MII_BMCR, BMCR_RESET);	/* PHY RESET */ | 
|  | iow(db, DM9000_GPR, 0x01);	/* Power-Down PHY */ | 
|  | iow(db, DM9000_IMR, IMR_PAR);	/* Disable all interrupt */ | 
|  | iow(db, DM9000_RCR, 0x00);	/* Disable RX */ | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Stop the interface. | 
|  | * The interface is stopped when it is brought. | 
|  | */ | 
|  | static int | 
|  | dm9000_stop(struct net_device *ndev) | 
|  | { | 
|  | board_info_t *db = netdev_priv(ndev); | 
|  |  | 
|  | if (netif_msg_ifdown(db)) | 
|  | dev_dbg(db->dev, "shutting down %s\n", ndev->name); | 
|  |  | 
|  | cancel_delayed_work_sync(&db->phy_poll); | 
|  |  | 
|  | netif_stop_queue(ndev); | 
|  | netif_carrier_off(ndev); | 
|  |  | 
|  | /* free interrupt */ | 
|  | free_irq(ndev->irq, ndev); | 
|  |  | 
|  | dm9000_shutdown(ndev); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct net_device_ops dm9000_netdev_ops = { | 
|  | .ndo_open		= dm9000_open, | 
|  | .ndo_stop		= dm9000_stop, | 
|  | .ndo_start_xmit		= dm9000_start_xmit, | 
|  | .ndo_tx_timeout		= dm9000_timeout, | 
|  | .ndo_set_rx_mode	= dm9000_hash_table, | 
|  | .ndo_do_ioctl		= dm9000_ioctl, | 
|  | .ndo_change_mtu		= eth_change_mtu, | 
|  | .ndo_set_features	= dm9000_set_features, | 
|  | .ndo_validate_addr	= eth_validate_addr, | 
|  | .ndo_set_mac_address	= eth_mac_addr, | 
|  | #ifdef CONFIG_NET_POLL_CONTROLLER | 
|  | .ndo_poll_controller	= dm9000_poll_controller, | 
|  | #endif | 
|  | }; | 
|  |  | 
|  | /* | 
|  | * Search DM9000 board, allocate space and register it | 
|  | */ | 
|  | static int __devinit | 
|  | dm9000_probe(struct platform_device *pdev) | 
|  | { | 
|  | struct dm9000_plat_data *pdata = pdev->dev.platform_data; | 
|  | struct board_info *db;	/* Point a board information structure */ | 
|  | struct net_device *ndev; | 
|  | const unsigned char *mac_src; | 
|  | int ret = 0; | 
|  | int iosize; | 
|  | int i; | 
|  | u32 id_val; | 
|  |  | 
|  | /* Init network device */ | 
|  | ndev = alloc_etherdev(sizeof(struct board_info)); | 
|  | if (!ndev) | 
|  | return -ENOMEM; | 
|  |  | 
|  | SET_NETDEV_DEV(ndev, &pdev->dev); | 
|  |  | 
|  | dev_dbg(&pdev->dev, "dm9000_probe()\n"); | 
|  |  | 
|  | /* setup board info structure */ | 
|  | db = netdev_priv(ndev); | 
|  |  | 
|  | db->dev = &pdev->dev; | 
|  | db->ndev = ndev; | 
|  |  | 
|  | spin_lock_init(&db->lock); | 
|  | mutex_init(&db->addr_lock); | 
|  |  | 
|  | INIT_DELAYED_WORK(&db->phy_poll, dm9000_poll_work); | 
|  |  | 
|  | db->addr_res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | 
|  | db->data_res = platform_get_resource(pdev, IORESOURCE_MEM, 1); | 
|  | db->irq_res  = platform_get_resource(pdev, IORESOURCE_IRQ, 0); | 
|  |  | 
|  | if (db->addr_res == NULL || db->data_res == NULL || | 
|  | db->irq_res == NULL) { | 
|  | dev_err(db->dev, "insufficient resources\n"); | 
|  | ret = -ENOENT; | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | db->irq_wake = platform_get_irq(pdev, 1); | 
|  | if (db->irq_wake >= 0) { | 
|  | dev_dbg(db->dev, "wakeup irq %d\n", db->irq_wake); | 
|  |  | 
|  | ret = request_irq(db->irq_wake, dm9000_wol_interrupt, | 
|  | IRQF_SHARED, dev_name(db->dev), ndev); | 
|  | if (ret) { | 
|  | dev_err(db->dev, "cannot get wakeup irq (%d)\n", ret); | 
|  | } else { | 
|  |  | 
|  | /* test to see if irq is really wakeup capable */ | 
|  | ret = irq_set_irq_wake(db->irq_wake, 1); | 
|  | if (ret) { | 
|  | dev_err(db->dev, "irq %d cannot set wakeup (%d)\n", | 
|  | db->irq_wake, ret); | 
|  | ret = 0; | 
|  | } else { | 
|  | irq_set_irq_wake(db->irq_wake, 0); | 
|  | db->wake_supported = 1; | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | iosize = resource_size(db->addr_res); | 
|  | db->addr_req = request_mem_region(db->addr_res->start, iosize, | 
|  | pdev->name); | 
|  |  | 
|  | if (db->addr_req == NULL) { | 
|  | dev_err(db->dev, "cannot claim address reg area\n"); | 
|  | ret = -EIO; | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | db->io_addr = ioremap(db->addr_res->start, iosize); | 
|  |  | 
|  | if (db->io_addr == NULL) { | 
|  | dev_err(db->dev, "failed to ioremap address reg\n"); | 
|  | ret = -EINVAL; | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | iosize = resource_size(db->data_res); | 
|  | db->data_req = request_mem_region(db->data_res->start, iosize, | 
|  | pdev->name); | 
|  |  | 
|  | if (db->data_req == NULL) { | 
|  | dev_err(db->dev, "cannot claim data reg area\n"); | 
|  | ret = -EIO; | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | db->io_data = ioremap(db->data_res->start, iosize); | 
|  |  | 
|  | if (db->io_data == NULL) { | 
|  | dev_err(db->dev, "failed to ioremap data reg\n"); | 
|  | ret = -EINVAL; | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | /* fill in parameters for net-dev structure */ | 
|  | ndev->base_addr = (unsigned long)db->io_addr; | 
|  | ndev->irq	= db->irq_res->start; | 
|  |  | 
|  | /* ensure at least we have a default set of IO routines */ | 
|  | dm9000_set_io(db, iosize); | 
|  |  | 
|  | /* check to see if anything is being over-ridden */ | 
|  | if (pdata != NULL) { | 
|  | /* check to see if the driver wants to over-ride the | 
|  | * default IO width */ | 
|  |  | 
|  | if (pdata->flags & DM9000_PLATF_8BITONLY) | 
|  | dm9000_set_io(db, 1); | 
|  |  | 
|  | if (pdata->flags & DM9000_PLATF_16BITONLY) | 
|  | dm9000_set_io(db, 2); | 
|  |  | 
|  | if (pdata->flags & DM9000_PLATF_32BITONLY) | 
|  | dm9000_set_io(db, 4); | 
|  |  | 
|  | /* check to see if there are any IO routine | 
|  | * over-rides */ | 
|  |  | 
|  | if (pdata->inblk != NULL) | 
|  | db->inblk = pdata->inblk; | 
|  |  | 
|  | if (pdata->outblk != NULL) | 
|  | db->outblk = pdata->outblk; | 
|  |  | 
|  | if (pdata->dumpblk != NULL) | 
|  | db->dumpblk = pdata->dumpblk; | 
|  |  | 
|  | db->flags = pdata->flags; | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL | 
|  | db->flags |= DM9000_PLATF_SIMPLE_PHY; | 
|  | #endif | 
|  |  | 
|  | dm9000_reset(db); | 
|  |  | 
|  | /* try multiple times, DM9000 sometimes gets the read wrong */ | 
|  | for (i = 0; i < 8; i++) { | 
|  | id_val  = ior(db, DM9000_VIDL); | 
|  | id_val |= (u32)ior(db, DM9000_VIDH) << 8; | 
|  | id_val |= (u32)ior(db, DM9000_PIDL) << 16; | 
|  | id_val |= (u32)ior(db, DM9000_PIDH) << 24; | 
|  |  | 
|  | if (id_val == DM9000_ID) | 
|  | break; | 
|  | dev_err(db->dev, "read wrong id 0x%08x\n", id_val); | 
|  | } | 
|  |  | 
|  | if (id_val != DM9000_ID) { | 
|  | dev_err(db->dev, "wrong id: 0x%08x\n", id_val); | 
|  | ret = -ENODEV; | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | /* Identify what type of DM9000 we are working on */ | 
|  |  | 
|  | id_val = ior(db, DM9000_CHIPR); | 
|  | dev_dbg(db->dev, "dm9000 revision 0x%02x\n", id_val); | 
|  |  | 
|  | switch (id_val) { | 
|  | case CHIPR_DM9000A: | 
|  | db->type = TYPE_DM9000A; | 
|  | break; | 
|  | case CHIPR_DM9000B: | 
|  | db->type = TYPE_DM9000B; | 
|  | break; | 
|  | default: | 
|  | dev_dbg(db->dev, "ID %02x => defaulting to DM9000E\n", id_val); | 
|  | db->type = TYPE_DM9000E; | 
|  | } | 
|  |  | 
|  | /* dm9000a/b are capable of hardware checksum offload */ | 
|  | if (db->type == TYPE_DM9000A || db->type == TYPE_DM9000B) { | 
|  | ndev->hw_features = NETIF_F_RXCSUM | NETIF_F_IP_CSUM; | 
|  | ndev->features |= ndev->hw_features; | 
|  | } | 
|  |  | 
|  | /* from this point we assume that we have found a DM9000 */ | 
|  |  | 
|  | /* driver system function */ | 
|  | ether_setup(ndev); | 
|  |  | 
|  | ndev->netdev_ops	= &dm9000_netdev_ops; | 
|  | ndev->watchdog_timeo	= msecs_to_jiffies(watchdog); | 
|  | ndev->ethtool_ops	= &dm9000_ethtool_ops; | 
|  |  | 
|  | db->msg_enable       = NETIF_MSG_LINK; | 
|  | db->mii.phy_id_mask  = 0x1f; | 
|  | db->mii.reg_num_mask = 0x1f; | 
|  | db->mii.force_media  = 0; | 
|  | db->mii.full_duplex  = 0; | 
|  | db->mii.dev	     = ndev; | 
|  | db->mii.mdio_read    = dm9000_phy_read; | 
|  | db->mii.mdio_write   = dm9000_phy_write; | 
|  |  | 
|  | mac_src = "eeprom"; | 
|  |  | 
|  | /* try reading the node address from the attached EEPROM */ | 
|  | for (i = 0; i < 6; i += 2) | 
|  | dm9000_read_eeprom(db, i / 2, ndev->dev_addr+i); | 
|  |  | 
|  | if (!is_valid_ether_addr(ndev->dev_addr) && pdata != NULL) { | 
|  | mac_src = "platform data"; | 
|  | memcpy(ndev->dev_addr, pdata->dev_addr, 6); | 
|  | } | 
|  |  | 
|  | if (!is_valid_ether_addr(ndev->dev_addr)) { | 
|  | /* try reading from mac */ | 
|  |  | 
|  | mac_src = "chip"; | 
|  | for (i = 0; i < 6; i++) | 
|  | ndev->dev_addr[i] = ior(db, i+DM9000_PAR); | 
|  | } | 
|  |  | 
|  | if (!is_valid_ether_addr(ndev->dev_addr)) { | 
|  | dev_warn(db->dev, "%s: Invalid ethernet MAC address. Please " | 
|  | "set using ifconfig\n", ndev->name); | 
|  |  | 
|  | eth_hw_addr_random(ndev); | 
|  | mac_src = "random"; | 
|  | } | 
|  |  | 
|  |  | 
|  | platform_set_drvdata(pdev, ndev); | 
|  | ret = register_netdev(ndev); | 
|  |  | 
|  | if (ret == 0) | 
|  | printk(KERN_INFO "%s: dm9000%c at %p,%p IRQ %d MAC: %pM (%s)\n", | 
|  | ndev->name, dm9000_type_to_char(db->type), | 
|  | db->io_addr, db->io_data, ndev->irq, | 
|  | ndev->dev_addr, mac_src); | 
|  | return 0; | 
|  |  | 
|  | out: | 
|  | dev_err(db->dev, "not found (%d).\n", ret); | 
|  |  | 
|  | dm9000_release_board(pdev, db); | 
|  | free_netdev(ndev); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int | 
|  | dm9000_drv_suspend(struct device *dev) | 
|  | { | 
|  | struct platform_device *pdev = to_platform_device(dev); | 
|  | struct net_device *ndev = platform_get_drvdata(pdev); | 
|  | board_info_t *db; | 
|  |  | 
|  | if (ndev) { | 
|  | db = netdev_priv(ndev); | 
|  | db->in_suspend = 1; | 
|  |  | 
|  | if (!netif_running(ndev)) | 
|  | return 0; | 
|  |  | 
|  | netif_device_detach(ndev); | 
|  |  | 
|  | /* only shutdown if not using WoL */ | 
|  | if (!db->wake_state) | 
|  | dm9000_shutdown(ndev); | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int | 
|  | dm9000_drv_resume(struct device *dev) | 
|  | { | 
|  | struct platform_device *pdev = to_platform_device(dev); | 
|  | struct net_device *ndev = platform_get_drvdata(pdev); | 
|  | board_info_t *db = netdev_priv(ndev); | 
|  |  | 
|  | if (ndev) { | 
|  | if (netif_running(ndev)) { | 
|  | /* reset if we were not in wake mode to ensure if | 
|  | * the device was powered off it is in a known state */ | 
|  | if (!db->wake_state) { | 
|  | dm9000_reset(db); | 
|  | dm9000_init_dm9000(ndev); | 
|  | } | 
|  |  | 
|  | netif_device_attach(ndev); | 
|  | } | 
|  |  | 
|  | db->in_suspend = 0; | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct dev_pm_ops dm9000_drv_pm_ops = { | 
|  | .suspend	= dm9000_drv_suspend, | 
|  | .resume		= dm9000_drv_resume, | 
|  | }; | 
|  |  | 
|  | static int __devexit | 
|  | dm9000_drv_remove(struct platform_device *pdev) | 
|  | { | 
|  | struct net_device *ndev = platform_get_drvdata(pdev); | 
|  |  | 
|  | platform_set_drvdata(pdev, NULL); | 
|  |  | 
|  | unregister_netdev(ndev); | 
|  | dm9000_release_board(pdev, netdev_priv(ndev)); | 
|  | free_netdev(ndev);		/* free device structure */ | 
|  |  | 
|  | dev_dbg(&pdev->dev, "released and freed device\n"); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static struct platform_driver dm9000_driver = { | 
|  | .driver	= { | 
|  | .name    = "dm9000", | 
|  | .owner	 = THIS_MODULE, | 
|  | .pm	 = &dm9000_drv_pm_ops, | 
|  | }, | 
|  | .probe   = dm9000_probe, | 
|  | .remove  = __devexit_p(dm9000_drv_remove), | 
|  | }; | 
|  |  | 
|  | static int __init | 
|  | dm9000_init(void) | 
|  | { | 
|  | printk(KERN_INFO "%s Ethernet Driver, V%s\n", CARDNAME, DRV_VERSION); | 
|  |  | 
|  | return platform_driver_register(&dm9000_driver); | 
|  | } | 
|  |  | 
|  | static void __exit | 
|  | dm9000_cleanup(void) | 
|  | { | 
|  | platform_driver_unregister(&dm9000_driver); | 
|  | } | 
|  |  | 
|  | module_init(dm9000_init); | 
|  | module_exit(dm9000_cleanup); | 
|  |  | 
|  | MODULE_AUTHOR("Sascha Hauer, Ben Dooks"); | 
|  | MODULE_DESCRIPTION("Davicom DM9000 network driver"); | 
|  | MODULE_LICENSE("GPL"); | 
|  | MODULE_ALIAS("platform:dm9000"); |