fddi: Move the FDDI drivers
Move the FDDI drivers into drivers/net/fddi/ and make the
necessary Kconfig and Makefile changes.
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
CC: Christoph Goos <cgoos@syskonnect.de>
CC: <linux@syskonnect.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index ef6b6be..7bdc22b 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -195,6 +195,8 @@
source "drivers/net/ethernet/Kconfig"
+source "drivers/net/fddi/Kconfig"
+
source "drivers/net/tokenring/Kconfig"
source "drivers/net/wireless/Kconfig"
@@ -268,76 +270,6 @@
depends on RIONET
default "128"
-config FDDI
- tristate "FDDI driver support"
- depends on (PCI || EISA || TC)
- help
- Fiber Distributed Data Interface is a high speed local area network
- design; essentially a replacement for high speed Ethernet. FDDI can
- run over copper or fiber. If you are connected to such a network and
- want a driver for the FDDI card in your computer, say Y here (and
- then also Y to the driver for your FDDI card, below). Most people
- will say N.
-
-config DEFXX
- tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
- depends on FDDI && (PCI || EISA || TC)
- ---help---
- This is support for the DIGITAL series of TURBOchannel (DEFTA),
- EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
- to a local FDDI network.
-
- To compile this driver as a module, choose M here: the module
- will be called defxx. If unsure, say N.
-
-config DEFXX_MMIO
- bool
- prompt "Use MMIO instead of PIO" if PCI || EISA
- depends on DEFXX
- default n if PCI || EISA
- default y
- ---help---
- This instructs the driver to use EISA or PCI memory-mapped I/O
- (MMIO) as appropriate instead of programmed I/O ports (PIO).
- Enabling this gives an improvement in processing time in parts
- of the driver, but it may cause problems with EISA (DEFEA)
- adapters. TURBOchannel does not have the concept of I/O ports,
- so MMIO is always used for these (DEFTA) adapters.
-
- If unsure, say N.
-
-config SKFP
- tristate "SysKonnect FDDI PCI support"
- depends on FDDI && PCI
- select BITREVERSE
- ---help---
- Say Y here if you have a SysKonnect FDDI PCI adapter.
- The following adapters are supported by this driver:
- - SK-5521 (SK-NET FDDI-UP)
- - SK-5522 (SK-NET FDDI-UP DAS)
- - SK-5541 (SK-NET FDDI-FP)
- - SK-5543 (SK-NET FDDI-LP)
- - SK-5544 (SK-NET FDDI-LP DAS)
- - SK-5821 (SK-NET FDDI-UP64)
- - SK-5822 (SK-NET FDDI-UP64 DAS)
- - SK-5841 (SK-NET FDDI-FP64)
- - SK-5843 (SK-NET FDDI-LP64)
- - SK-5844 (SK-NET FDDI-LP64 DAS)
- - Netelligent 100 FDDI DAS Fibre SC
- - Netelligent 100 FDDI SAS Fibre SC
- - Netelligent 100 FDDI DAS UTP
- - Netelligent 100 FDDI SAS UTP
- - Netelligent 100 FDDI SAS Fibre MIC
-
- Read <file:Documentation/networking/skfp.txt> for information about
- the driver.
-
- Questions concerning this driver can be addressed to:
- <linux@syskonnect.de>
-
- To compile this driver as a module, choose M here: the module
- will be called skfp. This is recommended.
-
config HIPPI
bool "HIPPI driver support (EXPERIMENTAL)"
depends on EXPERIMENTAL && INET && PCI