davinci: Add NAND flash support for DA850/OMAP-L138
This patch adds platform data for the 512MB NAND Flash
found on DA850/OMAP-L138 EVM. Currently it supports
only 1-bit ECC.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index eb998ce..62d37cb 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -18,6 +18,10 @@
#include <linux/i2c.h>
#include <linux/i2c/at24.h>
#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -26,6 +30,7 @@
#include <mach/irqs.h>
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
+#include <mach/nand.h>
#define DA850_EVM_PHY_MASK 0x1
#define DA850_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */
@@ -36,6 +41,74 @@
#define DA850_MMCSD_CD_PIN GPIO_TO_PIN(4, 0)
#define DA850_MMCSD_WP_PIN GPIO_TO_PIN(4, 1)
+/* DA850/OMAP-L138 EVM includes a 512 MByte large-page NAND flash
+ * (128K blocks). It may be used instead of the (default) SPI flash
+ * to boot, using TI's tools to install the secondary boot loader
+ * (UBL) and U-Boot.
+ */
+struct mtd_partition da850_evm_nandflash_partition[] = {
+ {
+ .name = "u-boot env",
+ .offset = 0,
+ .size = SZ_128K,
+ .mask_flags = MTD_WRITEABLE,
+ },
+ {
+ .name = "UBL",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_128K,
+ .mask_flags = MTD_WRITEABLE,
+ },
+ {
+ .name = "u-boot",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 4 * SZ_128K,
+ .mask_flags = MTD_WRITEABLE,
+ },
+ {
+ .name = "kernel",
+ .offset = 0x200000,
+ .size = SZ_2M,
+ .mask_flags = 0,
+ },
+ {
+ .name = "filesystem",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0,
+ },
+};
+
+static struct davinci_nand_pdata da850_evm_nandflash_data = {
+ .parts = da850_evm_nandflash_partition,
+ .nr_parts = ARRAY_SIZE(da850_evm_nandflash_partition),
+ .ecc_mode = NAND_ECC_HW,
+ .options = NAND_USE_FLASH_BBT,
+};
+
+static struct resource da850_evm_nandflash_resource[] = {
+ {
+ .start = DA8XX_AEMIF_CS3_BASE,
+ .end = DA8XX_AEMIF_CS3_BASE + SZ_512K + 2 * SZ_1K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = DA8XX_AEMIF_CTL_BASE,
+ .end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device da850_evm_nandflash_device = {
+ .name = "davinci_nand",
+ .id = 1,
+ .dev = {
+ .platform_data = &da850_evm_nandflash_data,
+ },
+ .num_resources = ARRAY_SIZE(da850_evm_nandflash_resource),
+ .resource = da850_evm_nandflash_resource,
+};
+
static struct davinci_i2c_platform_data da850_evm_i2c_0_pdata = {
.bus_freq = 100, /* kHz */
.bus_delay = 0, /* usec */
@@ -45,6 +118,10 @@
.enabled_uarts = 0x7,
};
+static struct platform_device *da850_evm_devices[] __initdata = {
+ &da850_evm_nandflash_device,
+};
+
/* davinci da850 evm audio machine driver */
static u8 da850_iis_serializer_direction[] = {
INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
@@ -120,6 +197,14 @@
struct davinci_soc_info *soc_info = &davinci_soc_info;
int ret;
+ ret = da8xx_pinmux_setup(da850_nand_pins);
+ if (ret)
+ pr_warning("da850_evm_init: nand mux setup failed: %d\n",
+ ret);
+
+ platform_add_devices(da850_evm_devices,
+ ARRAY_SIZE(da850_evm_devices));
+
ret = da8xx_register_edma();
if (ret)
pr_warning("da850_evm_init: edma registration failed: %d\n",