Initial Contribution
msm-2.6.38: tag AU_LINUX_ANDROID_GINGERBREAD.02.03.04.00.142
Signed-off-by: Bryan Huntsman <bryanh@codeaurora.org>
diff --git a/include/linux/mfd/pm8xxx/gpio.h b/include/linux/mfd/pm8xxx/gpio.h
new file mode 100644
index 0000000..0a9c95d
--- /dev/null
+++ b/include/linux/mfd/pm8xxx/gpio.h
@@ -0,0 +1,133 @@
+/*
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Qualcomm PMIC8XXX gpio driver header file
+ *
+ */
+
+#ifndef __PM8XXX_GPIO_H
+#define __PM8XXX_GPIO_H
+
+#include <linux/errno.h>
+
+#define PM8XXX_GPIO_DEV_NAME "pm8xxx-gpio"
+
+struct pm8xxx_gpio_core_data {
+ int ngpios;
+};
+
+struct pm8xxx_gpio_platform_data {
+ struct pm8xxx_gpio_core_data gpio_cdata;
+ int gpio_base;
+};
+
+/* GPIO parameters */
+/* direction */
+#define PM_GPIO_DIR_OUT 0x01
+#define PM_GPIO_DIR_IN 0x02
+#define PM_GPIO_DIR_BOTH (PM_GPIO_DIR_OUT | PM_GPIO_DIR_IN)
+
+/* output_buffer */
+#define PM_GPIO_OUT_BUF_OPEN_DRAIN 1
+#define PM_GPIO_OUT_BUF_CMOS 0
+
+/* pull */
+#define PM_GPIO_PULL_UP_30 0
+#define PM_GPIO_PULL_UP_1P5 1
+#define PM_GPIO_PULL_UP_31P5 2
+#define PM_GPIO_PULL_UP_1P5_30 3
+#define PM_GPIO_PULL_DN 4
+#define PM_GPIO_PULL_NO 5
+
+/* vin_sel: Voltage Input Select */
+#define PM_GPIO_VIN_VPH 0 /* 3v ~ 4.4v */
+#define PM_GPIO_VIN_BB 1 /* ~3.3v */
+#define PM_GPIO_VIN_S4 2 /* 1.8v */
+#define PM_GPIO_VIN_L15 3
+#define PM_GPIO_VIN_L4 4
+#define PM_GPIO_VIN_L3 5
+#define PM_GPIO_VIN_L17 6
+
+/* out_strength */
+#define PM_GPIO_STRENGTH_NO 0
+#define PM_GPIO_STRENGTH_HIGH 1
+#define PM_GPIO_STRENGTH_MED 2
+#define PM_GPIO_STRENGTH_LOW 3
+
+/* function */
+#define PM_GPIO_FUNC_NORMAL 0
+#define PM_GPIO_FUNC_PAIRED 1
+#define PM_GPIO_FUNC_1 2
+#define PM_GPIO_FUNC_2 3
+#define PM_GPIO_DTEST1 4
+#define PM_GPIO_DTEST2 5
+#define PM_GPIO_DTEST3 6
+#define PM_GPIO_DTEST4 7
+
+/**
+ * struct pm_gpio - structure to specify gpio configurtion values
+ * @direction: indicates whether the gpio should be input, output, or
+ * both. Should be of the type PM_GPIO_DIR_*
+ * @output_buffer: indicates gpio should be configured as CMOS or open
+ * drain. Should be of the type PM_GPIO_OUT_BUF_*
+ * @output_value: The gpio output value of the gpio line - 0 or 1
+ * @pull: Indicates whether a pull up or pull down should be
+ * applied. If a pullup is required the current strength
+ * needs to be specified. Current values of 30uA, 1.5uA,
+ * 31.5uA, 1.5uA with 30uA boost are supported. This value
+ * should be one of the PM_GPIO_PULL_*
+ * @vin_sel: specifies the voltage level when the output is set to 1.
+ * For an input gpio specifies the voltage level at which
+ * the input is interpreted as a logical 1.
+ * @out_strength: the amount of current supplied for an output gpio,
+ * should be of the type PM_GPIO_STRENGTH_*
+ * @function: choose alternate function for the gpio. Certain gpios
+ * can be paired (shorted) with each other. Some gpio pin
+ * can act as alternate functions. This parameter should
+ * be of type PM_GPIO_FUNC_*
+ * @inv_int_pol: Invert polarity before feeding the line to the interrupt
+ * module in pmic. This feature will almost be never used
+ * since the pm8xxx interrupt block can detect both edges
+ * and both levels.
+ * @disable_pin: Disable the gpio by configuring it as high impedance.
+ */
+struct pm_gpio {
+ int direction;
+ int output_buffer;
+ int output_value;
+ int pull;
+ int vin_sel;
+ int out_strength;
+ int function;
+ int inv_int_pol;
+ int disable_pin;
+};
+
+#if defined(CONFIG_GPIO_PM8XXX) || defined(CONFIG_GPIO_PM8XXX_MODULE)
+/**
+ * pm8xxx_gpio_config - configure a gpio controlled by a pm8xxx chip
+ * @gpio: gpio number to configure
+ * @param: configuration values
+ *
+ * RETURNS: an appropriate -ERRNO error value on error, or zero for success.
+ */
+int pm8xxx_gpio_config(int gpio, struct pm_gpio *param);
+#else
+static inline int pm8xxx_gpio_config(int gpio, struct pm_gpio *param)
+{
+ return -ENXIO;
+}
+#endif
+
+#endif