sh: Add support for R7780RP and R7780MP boards.
This adds support for the Renesas SH7780 development boards,
R7780RP and R7780MP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
diff --git a/arch/sh/drivers/pci/pci-sh7780.c b/arch/sh/drivers/pci/pci-sh7780.c
new file mode 100644
index 0000000..e097213
--- /dev/null
+++ b/arch/sh/drivers/pci/pci-sh7780.c
@@ -0,0 +1,341 @@
+/*
+ * Low-Level PCI Support for the SH7780
+ *
+ * Dustin McIntire (dustin@sensoria.com)
+ * Derived from arch/i386/kernel/pci-*.c which bore the message:
+ * (c) 1999--2000 Martin Mares <mj@ucw.cz>
+ *
+ * Ported to the new API by Paul Mundt <lethal@linux-sh.org>
+ * With cleanup by Paul van Gool <pvangool@mimotech.com>
+ *
+ * May be copied or modified under the terms of the GNU General Public
+ * License. See linux/COPYING for more information.
+ *
+ */
+
+#undef DEBUG
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/sched.h>
+#include <linux/ioport.h>
+#include <linux/errno.h>
+#include <linux/irq.h>
+#include <linux/delay.h>
+
+#include <asm/machvec.h>
+#include <asm/io.h>
+#include "pci-sh7780.h"
+
+static unsigned int pci_probe = PCI_PROBE_CONF1;
+extern int pci_fixup_pcic(void);
+
+/*
+ * Direct access to PCI hardware...
+ */
+
+#define CONFIG_CMD(bus, devfn, where) (0x80000000 | (bus->number << 16) | (devfn << 8) | (where & ~3))
+
+/*
+ * Functions for accessing PCI configuration space with type 1 accesses
+ */
+static int sh7780_pci_read(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 *val)
+{
+ unsigned long flags;
+ u32 data;
+
+ /*
+ * PCIPDR may only be accessed as 32 bit words,
+ * so we must do byte alignment by hand
+ */
+ local_irq_save(flags);
+ outl(CONFIG_CMD(bus, devfn, where), PCI_REG(SH7780_PCIPAR));
+ data = inl(PCI_REG(SH7780_PCIPDR));
+ local_irq_restore(flags);
+
+ switch (size) {
+ case 1:
+ *val = (data >> ((where & 3) << 3)) & 0xff;
+ break;
+ case 2:
+ *val = (data >> ((where & 2) << 3)) & 0xffff;
+ break;
+ case 4:
+ *val = data;
+ break;
+ default:
+ return PCIBIOS_FUNC_NOT_SUPPORTED;
+ }
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+/*
+ * Since SH7780 only does 32bit access we'll have to do a read,
+ * mask,write operation.
+ * We'll allow an odd byte offset, though it should be illegal.
+ */
+static int sh7780_pci_write(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 val)
+{
+ unsigned long flags;
+ int shift;
+ u32 data;
+
+ local_irq_save(flags);
+ outl(CONFIG_CMD(bus, devfn, where), PCI_REG(SH7780_PCIPAR));
+ data = inl(PCI_REG(SH7780_PCIPDR));
+ local_irq_restore(flags);
+
+ switch (size) {
+ case 1:
+ shift = (where & 3) << 3;
+ data &= ~(0xff << shift);
+ data |= ((val & 0xff) << shift);
+ break;
+ case 2:
+ shift = (where & 2) << 3;
+ data &= ~(0xffff << shift);
+ data |= ((val & 0xffff) << shift);
+ break;
+ case 4:
+ data = val;
+ break;
+ default:
+ return PCIBIOS_FUNC_NOT_SUPPORTED;
+ }
+
+ outl(data, PCI_REG(SH7780_PCIPDR));
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+#undef CONFIG_CMD
+
+struct pci_ops sh7780_pci_ops = {
+ .read = sh7780_pci_read,
+ .write = sh7780_pci_write,
+};
+
+static int __init pci_check_direct(void)
+{
+ unsigned int tmp, id;
+
+ outl(0x00000001, SH7780_PCI_VCR2); /* Enable PCIC */
+
+ /* check for SH7780/SH7780R hardware */
+ id = inl(PCI_REG(SH7780_PCIVID));
+ if ((id != ((SH7780_DEVICE_ID << 16) | SH7780_VENDOR_ID)) &&
+ (id != ((SH7781_DEVICE_ID << 16) | SH7780_VENDOR_ID))) {
+ printk(KERN_ERR "PCI: This is not an SH7780 (%x)\n", id);
+ return -ENODEV;
+ }
+
+ /*
+ * Check if configuration works.
+ */
+ if (pci_probe & PCI_PROBE_CONF1) {
+ tmp = inl(PCI_REG(SH7780_PCIPAR));
+ outl(0x80000000, PCI_REG(SH7780_PCIPAR));
+ if (inl(PCI_REG(SH7780_PCIPAR)) == 0x80000000) {
+ outl(tmp, PCI_REG(SH7780_PCIPAR));
+ printk(KERN_INFO "PCI: Using configuration type 1\n");
+ request_region(PCI_REG(SH7780_PCIPAR), 8, "PCI conf1");
+ return 0;
+ }
+ outl(tmp, PCI_REG(SH7780_PCIPAR));
+ }
+
+ pr_debug("PCI: pci_check_direct failed\n");
+ return -EINVAL;
+}
+
+/***************************************************************************************/
+
+/*
+ * Handle bus scanning and fixups ....
+ */
+
+static void __init pci_fixup_ide_bases(struct pci_dev *d)
+{
+ int i;
+
+ /*
+ * PCI IDE controllers use non-standard I/O port decoding, respect it.
+ */
+ if ((d->class >> 8) != PCI_CLASS_STORAGE_IDE)
+ return;
+ pr_debug("PCI: IDE base address fixup for %s\n", pci_name(d));
+ for(i=0; i<4; i++) {
+ struct resource *r = &d->resource[i];
+ if ((r->start & ~0x80) == 0x374) {
+ r->start |= 2;
+ r->end = r->start;
+ }
+ }
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, pci_fixup_ide_bases);
+
+/*
+ * Called after each bus is probed, but before its children
+ * are examined.
+ */
+
+void __init pcibios_fixup_bus(struct pci_bus *b)
+{
+ pci_read_bridge_bases(b);
+}
+
+/*
+ * Initialization. Try all known PCI access methods. Note that we support
+ * using both PCI BIOS and direct access: in such cases, we use I/O ports
+ * to access config space.
+ *
+ * Note that the platform specific initialization (BSC registers, and memory
+ * space mapping) will be called via the machine vectors (sh_mv.mv_pci_init()) if it
+ * exists and via the platform defined function pcibios_init_platform().
+ * See pci_bigsur.c for implementation;
+ *
+ * The BIOS version of the pci functions is not yet implemented but it is left
+ * in for completeness. Currently an error will be genereated at compile time.
+ */
+
+static int __init sh7780_pci_init(void)
+{
+ int ret;
+
+ pr_debug("PCI: Starting intialization.\n");
+
+ /* Setup the INTC */
+ ctrl_outl(0x00200000, INTC_ICR0); /* INTC SH-4 Mode */
+ ctrl_outl(0x00078000, INTC_INT2MSKCR); /* enable PCIINTA - PCIINTD */
+ ctrl_outl(0x40000000, INTC_INTMSK1); /* disable IRL4-7 Interrupt */
+ ctrl_outl(0x0000fffe, INTC_INTMSK2); /* disable IRL4-7 Interrupt */
+ ctrl_outl(0x80000000, INTC_INTMSKCLR1); /* enable IRL0-3 Interrupt */
+ ctrl_outl(0xfffe0000, INTC_INTMSKCLR2); /* enable IRL0-3 Interrupt */
+
+ if ((ret = pci_check_direct()) != 0)
+ return ret;
+
+ return pcibios_init_platform();
+}
+
+core_initcall(sh7780_pci_init);
+
+int __init sh7780_pcic_init(struct sh7780_pci_address_map *map)
+{
+ u32 word;
+
+ /*
+ * This code is unused for some boards as it is done in the
+ * bootloader and doing it here means the MAC addresses loaded
+ * by the bootloader get lost.
+ */
+ if (!(map->flags & SH7780_PCIC_NO_RESET)) {
+ /* toggle PCI reset pin */
+ word = SH7780_PCICR_PREFIX | SH7780_PCICR_PRST;
+ outl(word,PCI_REG(SH7780_PCICR));
+ /* Wait for a long time... not 1 sec. but long enough */
+ mdelay(100);
+ word = SH7780_PCICR_PREFIX;
+ outl(word,PCI_REG(SH7780_PCICR));
+ }
+
+ /* set the command/status bits to:
+ * Wait Cycle Control + Parity Enable + Bus Master +
+ * Mem space enable
+ */
+ outl(0x00000046, PCI_REG(SH7780_PCICMD));
+
+ /* define this host as the host bridge */
+ word = SH7780_PCI_HOST_BRIDGE << 24;
+ outl(word, PCI_REG(SH7780_PCIRID));
+
+ /* Set IO and Mem windows to local address
+ * Make PCI and local address the same for easy 1 to 1 mapping
+ * Window0 = map->window0.size @ non-cached area base = SDRAM
+ * Window1 = map->window1.size @ cached area base = SDRAM
+ */
+ word = ((map->window0.size - 1) & 0x1ff00001) | 0x01;
+ outl(0x07f00001, PCI_REG(SH7780_PCILSR0));
+ word = ((map->window1.size - 1) & 0x1ff00001) | 0x01;
+ outl(0x00000001, PCI_REG(SH7780_PCILSR1));
+ /* Set the values on window 0 PCI config registers */
+ word = P2SEGADDR(map->window0.base);
+ outl(0xa8000000, PCI_REG(SH7780_PCILAR0));
+ outl(0x08000000, PCI_REG(SH7780_PCIMBAR0));
+ /* Set the values on window 1 PCI config registers */
+ word = P2SEGADDR(map->window1.base);
+ outl(0x00000000, PCI_REG(SH7780_PCILAR1));
+ outl(0x00000000, PCI_REG(SH7780_PCIMBAR1));
+
+ /* Map IO space into PCI IO window
+ * The IO window is 64K-PCIBIOS_MIN_IO in size
+ * IO addresses will be translated to the
+ * PCI IO window base address
+ */
+ PCIDBG(3,"PCI: Mapping IO address 0x%x - 0x%x to base 0x%x\n", PCIBIOS_MIN_IO,
+ (64*1024), SH7780_PCI_IO_BASE+PCIBIOS_MIN_IO);
+
+ /* NOTE: I'm ignoring the PCI error IRQs for now..
+ * TODO: add support for the internal error interrupts and
+ * DMA interrupts...
+ */
+
+#ifdef CONFIG_SH_R7780RP
+ pci_fixup_pcic();
+#endif
+
+ /* SH7780 init done, set central function init complete */
+ /* use round robin mode to stop a device starving/overruning */
+ word = SH7780_PCICR_PREFIX | SH7780_PCICR_CFIN | /* SH7780_PCICR_ARBM |*/ SH7780_PCICR_FTO;
+ outl(word, PCI_REG(SH7780_PCICR));
+
+ return 1;
+}
+
+char * __init pcibios_setup(char *str)
+{
+ if (!strcmp(str, "off")) {
+ pci_probe = 0;
+ return NULL;
+ }
+
+ return str;
+}
+
+/*
+ * IRQ functions
+ */
+static u8 __init sh7780_no_swizzle(struct pci_dev *dev, u8 *pin)
+{
+ /* no swizzling */
+ return PCI_SLOT(dev->devfn);
+}
+
+static int sh7780_pci_lookup_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ int irq = -1;
+
+ /* now lookup the actual IRQ on a platform specific basis (pci-'platform'.c) */
+ irq = pcibios_map_platform_irq(slot,pin);
+ if( irq < 0 ) {
+ pr_debug("PCI: Error mapping IRQ on device %s\n", pci_name(dev));
+ return irq;
+ }
+
+ pr_debug("Setting IRQ for slot %s to %d\n", pci_name(dev), irq);
+
+ return irq;
+}
+
+void __init pcibios_fixup_irqs(void)
+{
+ pci_fixup_irqs(sh7780_no_swizzle, sh7780_pci_lookup_irq);
+}
+