|  | #ifndef FWH_LOCK_H | 
|  | #define FWH_LOCK_H | 
|  |  | 
|  |  | 
|  | enum fwh_lock_state { | 
|  | FWH_UNLOCKED   = 0, | 
|  | FWH_DENY_WRITE = 1, | 
|  | FWH_IMMUTABLE  = 2, | 
|  | FWH_DENY_READ  = 4, | 
|  | }; | 
|  |  | 
|  | struct fwh_xxlock_thunk { | 
|  | enum fwh_lock_state val; | 
|  | flstate_t state; | 
|  | }; | 
|  |  | 
|  |  | 
|  | #define FWH_XXLOCK_ONEBLOCK_LOCK   ((struct fwh_xxlock_thunk){ FWH_DENY_WRITE, FL_LOCKING}) | 
|  | #define FWH_XXLOCK_ONEBLOCK_UNLOCK ((struct fwh_xxlock_thunk){ FWH_UNLOCKED,   FL_UNLOCKING}) | 
|  |  | 
|  | /* | 
|  | * This locking/unlock is specific to firmware hub parts.  Only one | 
|  | * is known that supports the Intel command set.    Firmware | 
|  | * hub parts cannot be interleaved as they are on the LPC bus | 
|  | * so this code has not been tested with interleaved chips, | 
|  | * and will likely fail in that context. | 
|  | */ | 
|  | static int fwh_xxlock_oneblock(struct map_info *map, struct flchip *chip, | 
|  | unsigned long adr, int len, void *thunk) | 
|  | { | 
|  | struct cfi_private *cfi = map->fldrv_priv; | 
|  | struct fwh_xxlock_thunk *xxlt = (struct fwh_xxlock_thunk *)thunk; | 
|  | int ret; | 
|  |  | 
|  | /* Refuse the operation if the we cannot look behind the chip */ | 
|  | if (chip->start < 0x400000) { | 
|  | DEBUG( MTD_DEBUG_LEVEL3, | 
|  | "MTD %s(): chip->start: %lx wanted >= 0x400000\n", | 
|  | __func__, chip->start ); | 
|  | return -EIO; | 
|  | } | 
|  | /* | 
|  | * lock block registers: | 
|  | * - on 64k boundariesand | 
|  | * - bit 1 set high | 
|  | * - block lock registers are 4MiB lower - overflow subtract (danger) | 
|  | * | 
|  | * The address manipulation is first done on the logical address | 
|  | * which is 0 at the start of the chip, and then the offset of | 
|  | * the individual chip is addted to it.  Any other order a weird | 
|  | * map offset could cause problems. | 
|  | */ | 
|  | adr = (adr & ~0xffffUL) | 0x2; | 
|  | adr += chip->start - 0x400000; | 
|  |  | 
|  | /* | 
|  | * This is easy because these are writes to registers and not writes | 
|  | * to flash memory - that means that we don't have to check status | 
|  | * and timeout. | 
|  | */ | 
|  | mutex_lock(&chip->mutex); | 
|  | ret = get_chip(map, chip, adr, FL_LOCKING); | 
|  | if (ret) { | 
|  | mutex_unlock(&chip->mutex); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | chip->oldstate = chip->state; | 
|  | chip->state = xxlt->state; | 
|  | map_write(map, CMD(xxlt->val), adr); | 
|  |  | 
|  | /* Done and happy. */ | 
|  | chip->state = chip->oldstate; | 
|  | put_chip(map, chip, adr); | 
|  | mutex_unlock(&chip->mutex); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  |  | 
|  | static int fwh_lock_varsize(struct mtd_info *mtd, loff_t ofs, uint64_t len) | 
|  | { | 
|  | int ret; | 
|  |  | 
|  | ret = cfi_varsize_frob(mtd, fwh_xxlock_oneblock, ofs, len, | 
|  | (void *)&FWH_XXLOCK_ONEBLOCK_LOCK); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  |  | 
|  | static int fwh_unlock_varsize(struct mtd_info *mtd, loff_t ofs, uint64_t len) | 
|  | { | 
|  | int ret; | 
|  |  | 
|  | ret = cfi_varsize_frob(mtd, fwh_xxlock_oneblock, ofs, len, | 
|  | (void *)&FWH_XXLOCK_ONEBLOCK_UNLOCK); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static void fixup_use_fwh_lock(struct mtd_info *mtd, void *param) | 
|  | { | 
|  | printk(KERN_NOTICE "using fwh lock/unlock method\n"); | 
|  | /* Setup for the chips with the fwh lock method */ | 
|  | mtd->lock   = fwh_lock_varsize; | 
|  | mtd->unlock = fwh_unlock_varsize; | 
|  | } | 
|  | #endif /* FWH_LOCK_H */ |