iwlwifi: generalize iwlwifi init flow
This patch creates handlers to support
iwlwifi init flow for multiple HWs
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/iwlwifi/iwl-4965.c b/drivers/net/wireless/iwlwifi/iwl-4965.c
index 472ca3d..822169e 100644
--- a/drivers/net/wireless/iwlwifi/iwl-4965.c
+++ b/drivers/net/wireless/iwlwifi/iwl-4965.c
@@ -114,6 +114,151 @@
#endif /*CONFIG_IWL4965_HT */
+/* check contents of special bootstrap uCode SRAM */
+static int iwl4965_verify_bsm(struct iwl_priv *priv)
+{
+ __le32 *image = priv->ucode_boot.v_addr;
+ u32 len = priv->ucode_boot.len;
+ u32 reg;
+ u32 val;
+
+ IWL_DEBUG_INFO("Begin verify bsm\n");
+
+ /* verify BSM SRAM contents */
+ val = iwl_read_prph(priv, BSM_WR_DWCOUNT_REG);
+ for (reg = BSM_SRAM_LOWER_BOUND;
+ reg < BSM_SRAM_LOWER_BOUND + len;
+ reg += sizeof(u32), image++) {
+ val = iwl_read_prph(priv, reg);
+ if (val != le32_to_cpu(*image)) {
+ IWL_ERROR("BSM uCode verification failed at "
+ "addr 0x%08X+%u (of %u), is 0x%x, s/b 0x%x\n",
+ BSM_SRAM_LOWER_BOUND,
+ reg - BSM_SRAM_LOWER_BOUND, len,
+ val, le32_to_cpu(*image));
+ return -EIO;
+ }
+ }
+
+ IWL_DEBUG_INFO("BSM bootstrap uCode image OK\n");
+
+ return 0;
+}
+
+/**
+ * iwl4965_load_bsm - Load bootstrap instructions
+ *
+ * BSM operation:
+ *
+ * The Bootstrap State Machine (BSM) stores a short bootstrap uCode program
+ * in special SRAM that does not power down during RFKILL. When powering back
+ * up after power-saving sleeps (or during initial uCode load), the BSM loads
+ * the bootstrap program into the on-board processor, and starts it.
+ *
+ * The bootstrap program loads (via DMA) instructions and data for a new
+ * program from host DRAM locations indicated by the host driver in the
+ * BSM_DRAM_* registers. Once the new program is loaded, it starts
+ * automatically.
+ *
+ * When initializing the NIC, the host driver points the BSM to the
+ * "initialize" uCode image. This uCode sets up some internal data, then
+ * notifies host via "initialize alive" that it is complete.
+ *
+ * The host then replaces the BSM_DRAM_* pointer values to point to the
+ * normal runtime uCode instructions and a backup uCode data cache buffer
+ * (filled initially with starting data values for the on-board processor),
+ * then triggers the "initialize" uCode to load and launch the runtime uCode,
+ * which begins normal operation.
+ *
+ * When doing a power-save shutdown, runtime uCode saves data SRAM into
+ * the backup data cache in DRAM before SRAM is powered down.
+ *
+ * When powering back up, the BSM loads the bootstrap program. This reloads
+ * the runtime uCode instructions and the backup data cache into SRAM,
+ * and re-launches the runtime uCode from where it left off.
+ */
+static int iwl4965_load_bsm(struct iwl_priv *priv)
+{
+ __le32 *image = priv->ucode_boot.v_addr;
+ u32 len = priv->ucode_boot.len;
+ dma_addr_t pinst;
+ dma_addr_t pdata;
+ u32 inst_len;
+ u32 data_len;
+ int i;
+ u32 done;
+ u32 reg_offset;
+ int ret;
+
+ IWL_DEBUG_INFO("Begin load bsm\n");
+
+ /* make sure bootstrap program is no larger than BSM's SRAM size */
+ if (len > IWL_MAX_BSM_SIZE)
+ return -EINVAL;
+
+ /* Tell bootstrap uCode where to find the "Initialize" uCode
+ * in host DRAM ... host DRAM physical address bits 35:4 for 4965.
+ * NOTE: iwl4965_initialize_alive_start() will replace these values,
+ * after the "initialize" uCode has run, to point to
+ * runtime/protocol instructions and backup data cache. */
+ pinst = priv->ucode_init.p_addr >> 4;
+ pdata = priv->ucode_init_data.p_addr >> 4;
+ inst_len = priv->ucode_init.len;
+ data_len = priv->ucode_init_data.len;
+
+ ret = iwl_grab_nic_access(priv);
+ if (ret)
+ return ret;
+
+ iwl_write_prph(priv, BSM_DRAM_INST_PTR_REG, pinst);
+ iwl_write_prph(priv, BSM_DRAM_DATA_PTR_REG, pdata);
+ iwl_write_prph(priv, BSM_DRAM_INST_BYTECOUNT_REG, inst_len);
+ iwl_write_prph(priv, BSM_DRAM_DATA_BYTECOUNT_REG, data_len);
+
+ /* Fill BSM memory with bootstrap instructions */
+ for (reg_offset = BSM_SRAM_LOWER_BOUND;
+ reg_offset < BSM_SRAM_LOWER_BOUND + len;
+ reg_offset += sizeof(u32), image++)
+ _iwl_write_prph(priv, reg_offset, le32_to_cpu(*image));
+
+ ret = iwl4965_verify_bsm(priv);
+ if (ret) {
+ iwl_release_nic_access(priv);
+ return ret;
+ }
+
+ /* Tell BSM to copy from BSM SRAM into instruction SRAM, when asked */
+ iwl_write_prph(priv, BSM_WR_MEM_SRC_REG, 0x0);
+ iwl_write_prph(priv, BSM_WR_MEM_DST_REG, RTC_INST_LOWER_BOUND);
+ iwl_write_prph(priv, BSM_WR_DWCOUNT_REG, len / sizeof(u32));
+
+ /* Load bootstrap code into instruction SRAM now,
+ * to prepare to load "initialize" uCode */
+ iwl_write_prph(priv, BSM_WR_CTRL_REG, BSM_WR_CTRL_REG_BIT_START);
+
+ /* Wait for load of bootstrap uCode to finish */
+ for (i = 0; i < 100; i++) {
+ done = iwl_read_prph(priv, BSM_WR_CTRL_REG);
+ if (!(done & BSM_WR_CTRL_REG_BIT_START))
+ break;
+ udelay(10);
+ }
+ if (i < 100)
+ IWL_DEBUG_INFO("BSM write complete, poll %d iterations\n", i);
+ else {
+ IWL_ERROR("BSM write did not complete!\n");
+ return -EIO;
+ }
+
+ /* Enable future boot loads whenever power management unit triggers it
+ * (e.g. when powering back up after power-save shutdown) */
+ iwl_write_prph(priv, BSM_WR_CTRL_REG, BSM_WR_CTRL_REG_BIT_START_EN);
+
+ iwl_release_nic_access(priv);
+
+ return 0;
+}
+
static int iwl4965_init_drv(struct iwl_priv *priv)
{
int ret;
@@ -4789,6 +4934,10 @@
static struct iwl_lib_ops iwl4965_lib = {
.init_drv = iwl4965_init_drv,
+ .hw_nic_init = iwl4965_hw_nic_init,
+ .is_valid_rtc_data_addr = iwl4965_hw_valid_rtc_data_addr,
+ .alive_notify = iwl4965_alive_notify,
+ .load_ucode = iwl4965_load_bsm,
.eeprom_ops = {
.verify_signature = iwlcore_eeprom_verify_signature,
.acquire_semaphore = iwlcore_eeprom_acquire_semaphore,