include/linux/mmc/sdio.h - android_kernel_htc_msm8960 - Gitiles

 /*
  *  include/linux/mmc/sdio.h
  *
  *  Copyright 2006-2007 Pierre Ossman
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or (at
  * your option) any later version.
  */

 #ifndef LINUX_MMC_SDIO_H
 #define LINUX_MMC_SDIO_H

 /* SDIO commands                         type  argument     response */
 #define SD_IO_SEND_OP_COND          5 /* bcr  [23:0] OCR         R4  */
 #define SD_IO_RW_DIRECT            52 /* ac   [31:0] See below   R5  */
 #define SD_IO_RW_EXTENDED          53 /* adtc [31:0] See below   R5  */

 /*
  * SD_IO_RW_DIRECT argument format:
  *
  *      [31] R/W flag
  *      [30:28] Function number
  *      [27] RAW flag
  *      [25:9] Register address
  *      [7:0] Data
  */

 /*
  * SD_IO_RW_EXTENDED argument format:
  *
  *      [31] R/W flag
  *      [30:28] Function number
  *      [27] Block mode
  *      [26] Increment address
  *      [25:9] Register address
  *      [8:0] Byte/block count
  */

 #define R4_18V_PRESENT (1<<24)
 #define R4_MEMORY_PRESENT (1 << 27)

 /*
   SDIO status in R5
   Type
 	e : error bit
 	s : status bit
 	r : detected and set for the actual command response
 	x : detected and set during command execution. the host must poll
             the card by sending status command in order to read these bits.
   Clear condition
 	a : according to the card state
 	b : always related to the previous command. Reception of
             a valid command will clear it (with a delay of one command)
 	c : clear by read
  */

 #define R5_COM_CRC_ERROR	(1 << 15)	/* er, b */
 #define R5_ILLEGAL_COMMAND	(1 << 14)	/* er, b */
 #define R5_ERROR		(1 << 11)	/* erx, c */
 #define R5_FUNCTION_NUMBER	(1 << 9)	/* er, c */
 #define R5_OUT_OF_RANGE		(1 << 8)	/* er, c */
 #define R5_STATUS(x)		(x & 0xCB00)
 #define R5_IO_CURRENT_STATE(x)	((x & 0x3000) >> 12) /* s, b */

 /*
  * Card Common Control Registers (CCCR)
  */

 #define SDIO_CCCR_CCCR		0x00

 #define  SDIO_CCCR_REV_1_00	0	/* CCCR/FBR Version 1.00 */
 #define  SDIO_CCCR_REV_1_10	1	/* CCCR/FBR Version 1.10 */
 #define  SDIO_CCCR_REV_1_20	2	/* CCCR/FBR Version 1.20 */
 #define  SDIO_CCCR_REV_3_00	3	/* CCCR/FBR Version 3.00 */

 #define  SDIO_SDIO_REV_1_00	0	/* SDIO Spec Version 1.00 */
 #define  SDIO_SDIO_REV_1_10	1	/* SDIO Spec Version 1.10 */
 #define  SDIO_SDIO_REV_1_20	2	/* SDIO Spec Version 1.20 */
 #define  SDIO_SDIO_REV_2_00	3	/* SDIO Spec Version 2.00 */
 #define  SDIO_SDIO_REV_3_00	4	/* SDIO Spec Version 3.00 */

 #define SDIO_CCCR_SD		0x01

 #define  SDIO_SD_REV_1_01	0	/* SD Physical Spec Version 1.01 */
 #define  SDIO_SD_REV_1_10	1	/* SD Physical Spec Version 1.10 */
 #define  SDIO_SD_REV_2_00	2	/* SD Physical Spec Version 2.00 */
 #define  SDIO_SD_REV_3_00	3	/* SD Physical Spev Version 3.00 */

 #define SDIO_CCCR_IOEx		0x02
 #define SDIO_CCCR_IORx		0x03

 #define SDIO_CCCR_IENx		0x04	/* Function/Master Interrupt Enable */
 #define SDIO_CCCR_INTx		0x05	/* Function Interrupt Pending */

 #define SDIO_CCCR_ABORT		0x06	/* function abort/card reset */

 #define SDIO_CCCR_IF		0x07	/* bus interface controls */

 #define  SDIO_BUS_WIDTH_1BIT	0x00
 #define  SDIO_BUS_WIDTH_4BIT	0x02
 #define  SDIO_BUS_WIDTH_8BIT  	0x03
 #define  SDIO_BUS_ECSI		0x20	/* Enable continuous SPI interrupt */
 #define  SDIO_BUS_SCSI		0x40	/* Support continuous SPI interrupt */

 #define  SDIO_BUS_ASYNC_INT	0x20

 #define  SDIO_BUS_CD_DISABLE     0x80	/* disable pull-up on DAT3 (pin 1) */

 #define SDIO_CCCR_CAPS		0x08

 #define  SDIO_CCCR_CAP_SDC	0x01	/* can do CMD52 while data transfer */
 #define  SDIO_CCCR_CAP_SMB	0x02	/* can do multi-block xfers (CMD53) */
 #define  SDIO_CCCR_CAP_SRW	0x04	/* supports read-wait protocol */
 #define  SDIO_CCCR_CAP_SBS	0x08	/* supports suspend/resume */
 #define  SDIO_CCCR_CAP_S4MI	0x10	/* interrupt during 4-bit CMD53 */
 #define  SDIO_CCCR_CAP_E4MI	0x20	/* enable ints during 4-bit CMD53 */
 #define  SDIO_CCCR_CAP_LSC	0x40	/* low speed card */
 #define  SDIO_CCCR_CAP_4BLS	0x80	/* 4 bit low speed card */

 #define SDIO_CCCR_CIS		0x09	/* common CIS pointer (3 bytes) */

 /* Following 4 regs are valid only if SBS is set */
 #define SDIO_CCCR_SUSPEND	0x0c
 #define SDIO_CCCR_SELx		0x0d
 #define SDIO_CCCR_EXECx		0x0e
 #define SDIO_CCCR_READYx	0x0f

 #define SDIO_CCCR_BLKSIZE	0x10

 #define SDIO_CCCR_POWER		0x12

 #define  SDIO_POWER_SMPC	0x01	/* Supports Master Power Control */
 #define  SDIO_POWER_EMPC	0x02	/* Enable Master Power Control */

 #define SDIO_CCCR_SPEED		0x13

 #define  SDIO_SPEED_SHS		0x01	/* Supports High-Speed mode */
 #define  SDIO_SPEED_BSS_SHIFT	1
 #define  SDIO_SPEED_BSS_MASK	(7<<SDIO_SPEED_BSS_SHIFT)
 #define  SDIO_SPEED_SDR12	(0<<SDIO_SPEED_BSS_SHIFT)
 #define  SDIO_SPEED_SDR25	(1<<SDIO_SPEED_BSS_SHIFT)
 #define  SDIO_SPEED_SDR50	(2<<SDIO_SPEED_BSS_SHIFT)
 #define  SDIO_SPEED_SDR104	(3<<SDIO_SPEED_BSS_SHIFT)
 #define  SDIO_SPEED_DDR50	(4<<SDIO_SPEED_BSS_SHIFT)
 #define  SDIO_SPEED_EHS		SDIO_SPEED_SDR25	/* Enable High-Speed */

 #define SDIO_CCCR_UHS		0x14
 #define  SDIO_UHS_SDR50		0x01
 #define  SDIO_UHS_SDR104	0x02
 #define  SDIO_UHS_DDR50		0x04

 #define SDIO_CCCR_DRIVE_STRENGTH 0x15
 #define  SDIO_SDTx_MASK		0x07
 #define  SDIO_DRIVE_SDTA	(1<<0)
 #define  SDIO_DRIVE_SDTC	(1<<1)
 #define  SDIO_DRIVE_SDTD	(1<<2)
 #define  SDIO_DRIVE_DTSx_MASK	0x03
 #define  SDIO_DRIVE_DTSx_SHIFT	4
 #define  SDIO_DTSx_SET_TYPE_B	(0 << SDIO_DRIVE_DTSx_SHIFT)
 #define  SDIO_DTSx_SET_TYPE_A	(1 << SDIO_DRIVE_DTSx_SHIFT)
 #define  SDIO_DTSx_SET_TYPE_C	(2 << SDIO_DRIVE_DTSx_SHIFT)
 #define  SDIO_DTSx_SET_TYPE_D	(3 << SDIO_DRIVE_DTSx_SHIFT)
 /*
  * Function Basic Registers (FBR)
  */

 #define SDIO_FBR_BASE(f)	((f) * 0x100) /* base of function f's FBRs */

 #define SDIO_FBR_STD_IF		0x00

 #define  SDIO_FBR_SUPPORTS_CSA	0x40	/* supports Code Storage Area */
 #define  SDIO_FBR_ENABLE_CSA	0x80	/* enable Code Storage Area */

 #define SDIO_FBR_STD_IF_EXT	0x01

 #define SDIO_FBR_POWER		0x02

 #define  SDIO_FBR_POWER_SPS	0x01	/* Supports Power Selection */
 #define  SDIO_FBR_POWER_EPS	0x02	/* Enable (low) Power Selection */

 #define SDIO_FBR_CIS		0x09	/* CIS pointer (3 bytes) */


 #define SDIO_FBR_CSA		0x0C	/* CSA pointer (3 bytes) */

 #define SDIO_FBR_CSA_DATA	0x0F

 #define SDIO_FBR_BLKSIZE	0x10	/* block size (2 bytes) */

 #endif /* LINUX_MMC_SDIO_H */
	/*
	* include/linux/mmc/sdio.h
	*
	* Copyright 2006-2007 Pierre Ossman
	*
	* This program is free software; you can redistribute it and/or modify
	* it under the terms of the GNU General Public License as published by
	* the Free Software Foundation; either version 2 of the License, or (at
	* your option) any later version.
	*/

	#ifndef LINUX_MMC_SDIO_H
	#define LINUX_MMC_SDIO_H

	/* SDIO commands type argument response */
	#define SD_IO_SEND_OP_COND 5 /* bcr [23:0] OCR R4 */
	#define SD_IO_RW_DIRECT 52 /* ac [31:0] See below R5 */
	#define SD_IO_RW_EXTENDED 53 /* adtc [31:0] See below R5 */

	/*
	* SD_IO_RW_DIRECT argument format:
	*
	* [31] R/W flag
	* [30:28] Function number
	* [27] RAW flag
	* [25:9] Register address
	* [7:0] Data
	*/

	/*
	* SD_IO_RW_EXTENDED argument format:
	*
	* [31] R/W flag
	* [30:28] Function number
	* [27] Block mode
	* [26] Increment address
	* [25:9] Register address
	* [8:0] Byte/block count
	*/

	#define R4_18V_PRESENT (1<<24)
	#define R4_MEMORY_PRESENT (1 << 27)

	/*
	SDIO status in R5
	Type
	e : error bit
	s : status bit
	r : detected and set for the actual command response
	x : detected and set during command execution. the host must poll
	the card by sending status command in order to read these bits.
	Clear condition
	a : according to the card state
	b : always related to the previous command. Reception of
	a valid command will clear it (with a delay of one command)
	c : clear by read
	*/

	#define R5_COM_CRC_ERROR (1 << 15) /* er, b */
	#define R5_ILLEGAL_COMMAND (1 << 14) /* er, b */
	#define R5_ERROR (1 << 11) /* erx, c */
	#define R5_FUNCTION_NUMBER (1 << 9) /* er, c */
	#define R5_OUT_OF_RANGE (1 << 8) /* er, c */
	#define R5_STATUS(x) (x & 0xCB00)
	#define R5_IO_CURRENT_STATE(x) ((x & 0x3000) >> 12) /* s, b */

	/*
	* Card Common Control Registers (CCCR)
	*/

	#define SDIO_CCCR_CCCR 0x00

	#define SDIO_CCCR_REV_1_00 0 /* CCCR/FBR Version 1.00 */
	#define SDIO_CCCR_REV_1_10 1 /* CCCR/FBR Version 1.10 */
	#define SDIO_CCCR_REV_1_20 2 /* CCCR/FBR Version 1.20 */
	#define SDIO_CCCR_REV_3_00 3 /* CCCR/FBR Version 3.00 */

	#define SDIO_SDIO_REV_1_00 0 /* SDIO Spec Version 1.00 */
	#define SDIO_SDIO_REV_1_10 1 /* SDIO Spec Version 1.10 */
	#define SDIO_SDIO_REV_1_20 2 /* SDIO Spec Version 1.20 */
	#define SDIO_SDIO_REV_2_00 3 /* SDIO Spec Version 2.00 */
	#define SDIO_SDIO_REV_3_00 4 /* SDIO Spec Version 3.00 */

	#define SDIO_CCCR_SD 0x01

	#define SDIO_SD_REV_1_01 0 /* SD Physical Spec Version 1.01 */
	#define SDIO_SD_REV_1_10 1 /* SD Physical Spec Version 1.10 */
	#define SDIO_SD_REV_2_00 2 /* SD Physical Spec Version 2.00 */
	#define SDIO_SD_REV_3_00 3 /* SD Physical Spev Version 3.00 */

	#define SDIO_CCCR_IOEx 0x02
	#define SDIO_CCCR_IORx 0x03

	#define SDIO_CCCR_IENx 0x04 /* Function/Master Interrupt Enable */
	#define SDIO_CCCR_INTx 0x05 /* Function Interrupt Pending */

	#define SDIO_CCCR_ABORT 0x06 /* function abort/card reset */

	#define SDIO_CCCR_IF 0x07 /* bus interface controls */

	#define SDIO_BUS_WIDTH_1BIT 0x00
	#define SDIO_BUS_WIDTH_4BIT 0x02
	#define SDIO_BUS_WIDTH_8BIT 0x03
	#define SDIO_BUS_ECSI 0x20 /* Enable continuous SPI interrupt */
	#define SDIO_BUS_SCSI 0x40 /* Support continuous SPI interrupt */

	#define SDIO_BUS_ASYNC_INT 0x20

	#define SDIO_BUS_CD_DISABLE 0x80 /* disable pull-up on DAT3 (pin 1) */

	#define SDIO_CCCR_CAPS 0x08

	#define SDIO_CCCR_CAP_SDC 0x01 /* can do CMD52 while data transfer */
	#define SDIO_CCCR_CAP_SMB 0x02 /* can do multi-block xfers (CMD53) */
	#define SDIO_CCCR_CAP_SRW 0x04 /* supports read-wait protocol */
	#define SDIO_CCCR_CAP_SBS 0x08 /* supports suspend/resume */
	#define SDIO_CCCR_CAP_S4MI 0x10 /* interrupt during 4-bit CMD53 */
	#define SDIO_CCCR_CAP_E4MI 0x20 /* enable ints during 4-bit CMD53 */
	#define SDIO_CCCR_CAP_LSC 0x40 /* low speed card */
	#define SDIO_CCCR_CAP_4BLS 0x80 /* 4 bit low speed card */

	#define SDIO_CCCR_CIS 0x09 /* common CIS pointer (3 bytes) */

	/* Following 4 regs are valid only if SBS is set */
	#define SDIO_CCCR_SUSPEND 0x0c
	#define SDIO_CCCR_SELx 0x0d
	#define SDIO_CCCR_EXECx 0x0e
	#define SDIO_CCCR_READYx 0x0f

	#define SDIO_CCCR_BLKSIZE 0x10

	#define SDIO_CCCR_POWER 0x12

	#define SDIO_POWER_SMPC 0x01 /* Supports Master Power Control */
	#define SDIO_POWER_EMPC 0x02 /* Enable Master Power Control */

	#define SDIO_CCCR_SPEED 0x13

	#define SDIO_SPEED_SHS 0x01 /* Supports High-Speed mode */
	#define SDIO_SPEED_BSS_SHIFT 1
	#define SDIO_SPEED_BSS_MASK (7<<SDIO_SPEED_BSS_SHIFT)
	#define SDIO_SPEED_SDR12 (0<<SDIO_SPEED_BSS_SHIFT)
	#define SDIO_SPEED_SDR25 (1<<SDIO_SPEED_BSS_SHIFT)
	#define SDIO_SPEED_SDR50 (2<<SDIO_SPEED_BSS_SHIFT)
	#define SDIO_SPEED_SDR104 (3<<SDIO_SPEED_BSS_SHIFT)
	#define SDIO_SPEED_DDR50 (4<<SDIO_SPEED_BSS_SHIFT)
	#define SDIO_SPEED_EHS SDIO_SPEED_SDR25 /* Enable High-Speed */

	#define SDIO_CCCR_UHS 0x14
	#define SDIO_UHS_SDR50 0x01
	#define SDIO_UHS_SDR104 0x02
	#define SDIO_UHS_DDR50 0x04

	#define SDIO_CCCR_DRIVE_STRENGTH 0x15
	#define SDIO_SDTx_MASK 0x07
	#define SDIO_DRIVE_SDTA (1<<0)
	#define SDIO_DRIVE_SDTC (1<<1)
	#define SDIO_DRIVE_SDTD (1<<2)
	#define SDIO_DRIVE_DTSx_MASK 0x03
	#define SDIO_DRIVE_DTSx_SHIFT 4
	#define SDIO_DTSx_SET_TYPE_B (0 << SDIO_DRIVE_DTSx_SHIFT)
	#define SDIO_DTSx_SET_TYPE_A (1 << SDIO_DRIVE_DTSx_SHIFT)
	#define SDIO_DTSx_SET_TYPE_C (2 << SDIO_DRIVE_DTSx_SHIFT)
	#define SDIO_DTSx_SET_TYPE_D (3 << SDIO_DRIVE_DTSx_SHIFT)
	/*
	* Function Basic Registers (FBR)
	*/

	#define SDIO_FBR_BASE(f) ((f) * 0x100) /* base of function f's FBRs */

	#define SDIO_FBR_STD_IF 0x00

	#define SDIO_FBR_SUPPORTS_CSA 0x40 /* supports Code Storage Area */
	#define SDIO_FBR_ENABLE_CSA 0x80 /* enable Code Storage Area */

	#define SDIO_FBR_STD_IF_EXT 0x01

	#define SDIO_FBR_POWER 0x02

	#define SDIO_FBR_POWER_SPS 0x01 /* Supports Power Selection */
	#define SDIO_FBR_POWER_EPS 0x02 /* Enable (low) Power Selection */

	#define SDIO_FBR_CIS 0x09 /* CIS pointer (3 bytes) */


	#define SDIO_FBR_CSA 0x0C /* CSA pointer (3 bytes) */

	#define SDIO_FBR_CSA_DATA 0x0F

	#define SDIO_FBR_BLKSIZE 0x10 /* block size (2 bytes) */

	#endif /* LINUX_MMC_SDIO_H */