| /* | 
 |  * Bitbanged MDIO support. | 
 |  * | 
 |  * Author: Scott Wood <scottwood@freescale.com> | 
 |  * Copyright (c) 2007 Freescale Semiconductor | 
 |  * | 
 |  * Based on CPM2 MDIO code which is: | 
 |  * | 
 |  * Copyright (c) 2003 Intracom S.A. | 
 |  *  by Pantelis Antoniou <panto@intracom.gr> | 
 |  * | 
 |  * 2005 (c) MontaVista Software, Inc. | 
 |  * Vitaly Bordug <vbordug@ru.mvista.com> | 
 |  * | 
 |  * This file is licensed under the terms of the GNU General Public License | 
 |  * version 2. This program is licensed "as is" without any warranty of any | 
 |  * kind, whether express or implied. | 
 |  */ | 
 |  | 
 | #include <linux/module.h> | 
 | #include <linux/mdio-bitbang.h> | 
 | #include <linux/slab.h> | 
 | #include <linux/types.h> | 
 | #include <linux/delay.h> | 
 |  | 
 | #define MDIO_READ 1 | 
 | #define MDIO_WRITE 0 | 
 |  | 
 | #define MDIO_SETUP_TIME 10 | 
 | #define MDIO_HOLD_TIME 10 | 
 |  | 
 | /* Minimum MDC period is 400 ns, plus some margin for error.  MDIO_DELAY | 
 |  * is done twice per period. | 
 |  */ | 
 | #define MDIO_DELAY 250 | 
 |  | 
 | /* The PHY may take up to 300 ns to produce data, plus some margin | 
 |  * for error. | 
 |  */ | 
 | #define MDIO_READ_DELAY 350 | 
 |  | 
 | /* MDIO must already be configured as output. */ | 
 | static void mdiobb_send_bit(struct mdiobb_ctrl *ctrl, int val) | 
 | { | 
 | 	const struct mdiobb_ops *ops = ctrl->ops; | 
 |  | 
 | 	ops->set_mdio_data(ctrl, val); | 
 | 	ndelay(MDIO_DELAY); | 
 | 	ops->set_mdc(ctrl, 1); | 
 | 	ndelay(MDIO_DELAY); | 
 | 	ops->set_mdc(ctrl, 0); | 
 | } | 
 |  | 
 | /* MDIO must already be configured as input. */ | 
 | static int mdiobb_get_bit(struct mdiobb_ctrl *ctrl) | 
 | { | 
 | 	const struct mdiobb_ops *ops = ctrl->ops; | 
 |  | 
 | 	ndelay(MDIO_DELAY); | 
 | 	ops->set_mdc(ctrl, 1); | 
 | 	ndelay(MDIO_READ_DELAY); | 
 | 	ops->set_mdc(ctrl, 0); | 
 |  | 
 | 	return ops->get_mdio_data(ctrl); | 
 | } | 
 |  | 
 | /* MDIO must already be configured as output. */ | 
 | static void mdiobb_send_num(struct mdiobb_ctrl *ctrl, u16 val, int bits) | 
 | { | 
 | 	int i; | 
 |  | 
 | 	for (i = bits - 1; i >= 0; i--) | 
 | 		mdiobb_send_bit(ctrl, (val >> i) & 1); | 
 | } | 
 |  | 
 | /* MDIO must already be configured as input. */ | 
 | static u16 mdiobb_get_num(struct mdiobb_ctrl *ctrl, int bits) | 
 | { | 
 | 	int i; | 
 | 	u16 ret = 0; | 
 |  | 
 | 	for (i = bits - 1; i >= 0; i--) { | 
 | 		ret <<= 1; | 
 | 		ret |= mdiobb_get_bit(ctrl); | 
 | 	} | 
 |  | 
 | 	return ret; | 
 | } | 
 |  | 
 | /* Utility to send the preamble, address, and | 
 |  * register (common to read and write). | 
 |  */ | 
 | static void mdiobb_cmd(struct mdiobb_ctrl *ctrl, int read, u8 phy, u8 reg) | 
 | { | 
 | 	const struct mdiobb_ops *ops = ctrl->ops; | 
 | 	int i; | 
 |  | 
 | 	ops->set_mdio_dir(ctrl, 1); | 
 |  | 
 | 	/* | 
 | 	 * Send a 32 bit preamble ('1's) with an extra '1' bit for good | 
 | 	 * measure.  The IEEE spec says this is a PHY optional | 
 | 	 * requirement.  The AMD 79C874 requires one after power up and | 
 | 	 * one after a MII communications error.  This means that we are | 
 | 	 * doing more preambles than we need, but it is safer and will be | 
 | 	 * much more robust. | 
 | 	 */ | 
 |  | 
 | 	for (i = 0; i < 32; i++) | 
 | 		mdiobb_send_bit(ctrl, 1); | 
 |  | 
 | 	/* send the start bit (01) and the read opcode (10) or write (10) */ | 
 | 	mdiobb_send_bit(ctrl, 0); | 
 | 	mdiobb_send_bit(ctrl, 1); | 
 | 	mdiobb_send_bit(ctrl, read); | 
 | 	mdiobb_send_bit(ctrl, !read); | 
 |  | 
 | 	mdiobb_send_num(ctrl, phy, 5); | 
 | 	mdiobb_send_num(ctrl, reg, 5); | 
 | } | 
 |  | 
 |  | 
 | static int mdiobb_read(struct mii_bus *bus, int phy, int reg) | 
 | { | 
 | 	struct mdiobb_ctrl *ctrl = bus->priv; | 
 | 	int ret, i; | 
 |  | 
 | 	mdiobb_cmd(ctrl, MDIO_READ, phy, reg); | 
 | 	ctrl->ops->set_mdio_dir(ctrl, 0); | 
 |  | 
 | 	/* check the turnaround bit: the PHY should be driving it to zero */ | 
 | 	if (mdiobb_get_bit(ctrl) != 0) { | 
 | 		/* PHY didn't drive TA low -- flush any bits it | 
 | 		 * may be trying to send. | 
 | 		 */ | 
 | 		for (i = 0; i < 32; i++) | 
 | 			mdiobb_get_bit(ctrl); | 
 |  | 
 | 		return 0xffff; | 
 | 	} | 
 |  | 
 | 	ret = mdiobb_get_num(ctrl, 16); | 
 | 	mdiobb_get_bit(ctrl); | 
 | 	return ret; | 
 | } | 
 |  | 
 | static int mdiobb_write(struct mii_bus *bus, int phy, int reg, u16 val) | 
 | { | 
 | 	struct mdiobb_ctrl *ctrl = bus->priv; | 
 |  | 
 | 	mdiobb_cmd(ctrl, MDIO_WRITE, phy, reg); | 
 |  | 
 | 	/* send the turnaround (10) */ | 
 | 	mdiobb_send_bit(ctrl, 1); | 
 | 	mdiobb_send_bit(ctrl, 0); | 
 |  | 
 | 	mdiobb_send_num(ctrl, val, 16); | 
 |  | 
 | 	ctrl->ops->set_mdio_dir(ctrl, 0); | 
 | 	mdiobb_get_bit(ctrl); | 
 | 	return 0; | 
 | } | 
 |  | 
 | struct mii_bus *alloc_mdio_bitbang(struct mdiobb_ctrl *ctrl) | 
 | { | 
 | 	struct mii_bus *bus; | 
 |  | 
 | 	bus = kzalloc(sizeof(struct mii_bus), GFP_KERNEL); | 
 | 	if (!bus) | 
 | 		return NULL; | 
 |  | 
 | 	__module_get(ctrl->ops->owner); | 
 |  | 
 | 	bus->read = mdiobb_read; | 
 | 	bus->write = mdiobb_write; | 
 | 	bus->priv = ctrl; | 
 |  | 
 | 	return bus; | 
 | } | 
 |  | 
 | void free_mdio_bitbang(struct mii_bus *bus) | 
 | { | 
 | 	struct mdiobb_ctrl *ctrl = bus->priv; | 
 |  | 
 | 	module_put(ctrl->ops->owner); | 
 | 	kfree(bus); | 
 | } | 
 |  | 
 | MODULE_LICENSE("GPL"); |