[AVR32] Add support for ATSTK1003 and ATSTK1004
ATSTK1003 and ATSTK1004 are CPU daughterboards for ATSTK1000 featuring
the AT32AP7001 and AT32AP7002 CPUs, respectively.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig
index 23e8c84..28c4780 100644
--- a/arch/avr32/boards/atstk1000/Kconfig
+++ b/arch/avr32/boards/atstk1000/Kconfig
@@ -1,34 +1,34 @@
# STK1000 customization
-if BOARD_ATSTK1002
+if BOARD_ATSTK1000
-config BOARD_ATSTK1002_CUSTOM
- bool "Non-default STK-1002 jumper settings"
+config BOARD_ATSTK100X_CUSTOM
+ bool "Non-default STK1002/STK1003/STK1004 jumper settings"
help
You will normally leave the jumpers on the CPU card at their
default settings. If you need to use certain peripherals,
you will need to change some of those jumpers.
-if BOARD_ATSTK1002_CUSTOM
+if BOARD_ATSTK100X_CUSTOM
-config BOARD_ATSTK1002_SW1_CUSTOM
+config BOARD_ATSTK100X_SW1_CUSTOM
bool "SW1: use SSC1 (not SPI0)"
help
This also prevents using the external DAC as an audio interface,
and means you can't initialize the on-board QVGA display.
-config BOARD_ATSTK1002_SW2_CUSTOM
+config BOARD_ATSTK100X_SW2_CUSTOM
bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)"
help
If you change this you'll want an updated boot loader putting
the console on UART-C not UART-A.
-config BOARD_ATSTK1002_SW3_CUSTOM
+config BOARD_ATSTK100X_SW3_CUSTOM
bool "SW3: use TIMER1 (not SSC0 and GCLK)"
help
This also prevents using the external DAC as an audio interface.
-config BOARD_ATSTK1002_SW4_CUSTOM
+config BOARD_ATSTK100X_SW4_CUSTOM
bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)"
help
To use the camera interface you'll need a custom card (on the
@@ -36,15 +36,17 @@
config BOARD_ATSTK1002_SW5_CUSTOM
bool "SW5: use MACB1 (not LCDC)"
+ depends on BOARD_ATSTK1002
config BOARD_ATSTK1002_SW6_CUSTOM
bool "SW6: more GPIOs (not MACB0)"
+ depends on BOARD_ATSTK1002
endif # custom
-config BOARD_ATSTK1002_SPI1
+config BOARD_ATSTK100X_SPI1
bool "Configure SPI1 controller"
- depends on !BOARD_ATSTK1002_SW4_CUSTOM
+ depends on !BOARD_ATSTK100X_SW4_CUSTOM
help
All the signals for the second SPI controller are available on
GPIO lines and accessed through the J1 jumper block. Say "y"
@@ -56,7 +58,7 @@
choice
prompt "LEDs connected to J2:"
- depends on LEDS_GPIO && !BOARD_ATSTK1002_SW4_CUSTOM
+ depends on LEDS_GPIO && !BOARD_ATSTK100X_SW4_CUSTOM
optional
help
Select this if you have jumpered the J2 jumper block to the
@@ -78,7 +80,7 @@
config BOARD_ATSTK1000_EXTDAC
bool
- depends on !BOARD_ATSTK1002_SW1_CUSTOM && !BOARD_ATSTK1002_SW3_CUSTOM
+ depends on !BOARD_ATSTK100X_SW1_CUSTOM && !BOARD_ATSTK100X_SW3_CUSTOM
default y
-endif # stk 1002
+endif # stk 1000