iwlwifi: name changed from "fat" to "ht40"
Rename "fat" to "ht40"
The term "fat channel" is deprecated in favor of "HT40"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/iwlwifi/iwl-commands.h b/drivers/net/wireless/iwlwifi/iwl-commands.h
index 39ede57..6188c54 100644
--- a/drivers/net/wireless/iwlwifi/iwl-commands.h
+++ b/drivers/net/wireless/iwlwifi/iwl-commands.h
@@ -283,7 +283,7 @@
* 1) Dual stream (MIMO)
* 2) Triple stream (MIMO)
*
- * 5: Value of 0x20 in bits 7:0 indicates 6 Mbps FAT duplicate data
+ * 5: Value of 0x20 in bits 7:0 indicates 6 Mbps HT40 duplicate data
*
* Legacy OFDM rate format for bits 7:0 (bit 8 must be "0", bit 9 "0"):
* 3-0: 0xD) 6 Mbps
@@ -320,11 +320,11 @@
#define RATE_MCS_GF_POS 10
#define RATE_MCS_GF_MSK 0x400
-/* Bit 11: (1) Use 40Mhz FAT chnl width, (0) use 20 MHz legacy chnl width */
-#define RATE_MCS_FAT_POS 11
-#define RATE_MCS_FAT_MSK 0x800
+/* Bit 11: (1) Use 40Mhz HT40 chnl width, (0) use 20 MHz legacy chnl width */
+#define RATE_MCS_HT40_POS 11
+#define RATE_MCS_HT40_MSK 0x800
-/* Bit 12: (1) Duplicate data on both 20MHz chnls. FAT (bit 11) must be set. */
+/* Bit 12: (1) Duplicate data on both 20MHz chnls. HT40 (bit 11) must be set. */
#define RATE_MCS_DUP_POS 12
#define RATE_MCS_DUP_MSK 0x1000
@@ -459,7 +459,7 @@
/* calibration values from "initialize" uCode */
__le32 voltage; /* signed, higher value is lower voltage */
- __le32 therm_r1[2]; /* signed, 1st for normal, 2nd for FAT channel*/
+ __le32 therm_r1[2]; /* signed, 1st for normal, 2nd for HT40 */
__le32 therm_r2[2]; /* signed */
__le32 therm_r3[2]; /* signed */
__le32 therm_r4[2]; /* signed */
@@ -610,7 +610,7 @@
#define RXON_FLG_HT_OPERATING_MODE_POS (23)
#define RXON_FLG_HT_PROT_MSK cpu_to_le32(0x1 << 23)
-#define RXON_FLG_FAT_PROT_MSK cpu_to_le32(0x2 << 23)
+#define RXON_FLG_HT40_PROT_MSK cpu_to_le32(0x2 << 23)
#define RXON_FLG_CHANNEL_MODE_POS (25)
#define RXON_FLG_CHANNEL_MODE_MSK cpu_to_le32(0x3 << 25)
@@ -891,7 +891,7 @@
#define STA_FLG_AGG_MPDU_8US_MSK cpu_to_le32(1 << 18)
#define STA_FLG_MAX_AGG_SIZE_POS (19)
#define STA_FLG_MAX_AGG_SIZE_MSK cpu_to_le32(3 << 19)
-#define STA_FLG_FAT_EN_MSK cpu_to_le32(1 << 21)
+#define STA_FLG_HT40_EN_MSK cpu_to_le32(1 << 21)
#define STA_FLG_MIMO_DIS_MSK cpu_to_le32(1 << 22)
#define STA_FLG_AGG_MPDU_DENSITY_POS (23)
#define STA_FLG_AGG_MPDU_DENSITY_MSK cpu_to_le32(7 << 23)
@@ -1984,10 +1984,10 @@
* a) Use this same initial rate for first 3 entries.
* b) Find next lower available rate using same mode (SISO or MIMO),
* use for next 3 entries. If no lower rate available, switch to
- * legacy mode (no FAT channel, no MIMO, no short guard interval).
+ * legacy mode (no HT40 channel, no MIMO, no short guard interval).
* c) If using MIMO, set command's mimo_delimiter to number of entries
* using MIMO (3 or 6).
- * d) After trying 2 HT rates, switch to legacy mode (no FAT channel,
+ * d) After trying 2 HT rates, switch to legacy mode (no HT40 channel,
* no MIMO, no short guard interval), at the next lower bit rate
* (e.g. if second HT bit rate was 54, try 48 legacy), and follow
* legacy procedure for remaining table entries.
@@ -3017,7 +3017,7 @@
* one channel that has just been scanned.
*/
#define STATISTICS_REPLY_FLG_BAND_24G_MSK cpu_to_le32(0x2)
-#define STATISTICS_REPLY_FLG_FAT_MODE_MSK cpu_to_le32(0x8)
+#define STATISTICS_REPLY_FLG_HT40_MODE_MSK cpu_to_le32(0x8)
struct iwl3945_notif_statistics {
__le32 flag;