[SCSI] isci: enable wide port targets
Arrange for task_contexts prepared for the wide targets to account for
all the attached phys in the port.
Signed-off-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
diff --git a/drivers/scsi/isci/port.c b/drivers/scsi/isci/port.c
index 4cb071d..49e8a72 100644
--- a/drivers/scsi/isci/port.c
+++ b/drivers/scsi/isci/port.c
@@ -114,7 +114,7 @@
* value is returned if the specified port is not valid. When this value is
* returned, no data is copied to the properties output parameter.
*/
-static enum sci_status sci_port_get_properties(struct isci_port *iport,
+enum sci_status sci_port_get_properties(struct isci_port *iport,
struct sci_port_properties *prop)
{
if (!iport || iport->logical_port_index == SCIC_SDS_DUMMY_PORT)
diff --git a/drivers/scsi/isci/port.h b/drivers/scsi/isci/port.h
index cb5ffbc..b3a7f12 100644
--- a/drivers/scsi/isci/port.h
+++ b/drivers/scsi/isci/port.h
@@ -250,6 +250,10 @@
struct isci_port *iport,
struct isci_phy *iphy);
+enum sci_status sci_port_get_properties(
+ struct isci_port *iport,
+ struct sci_port_properties *prop);
+
enum sci_status sci_port_link_up(struct isci_port *iport,
struct isci_phy *iphy);
enum sci_status sci_port_link_down(struct isci_port *iport,
diff --git a/drivers/scsi/isci/remote_device.c b/drivers/scsi/isci/remote_device.c
index b207cd3..dd74b6c 100644
--- a/drivers/scsi/isci/remote_device.c
+++ b/drivers/scsi/isci/remote_device.c
@@ -53,6 +53,7 @@
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include <scsi/sas.h>
+#include <linux/bitops.h>
#include "isci.h"
#include "port.h"
#include "remote_device.h"
@@ -1101,6 +1102,7 @@
struct isci_remote_device *idev)
{
enum sci_status status;
+ struct sci_port_properties properties;
struct domain_device *dev = idev->domain_dev;
sci_remote_device_construct(iport, idev);
@@ -1110,6 +1112,11 @@
* entries will be needed to store the remote node.
*/
idev->is_direct_attached = true;
+
+ sci_port_get_properties(iport, &properties);
+ /* Get accurate port width from port's phy mask for a DA device. */
+ idev->device_port_width = hweight32(properties.phy_mask);
+
status = sci_controller_allocate_remote_node_context(iport->owning_controller,
idev,
&idev->rnc.remote_node_index);
@@ -1125,9 +1132,6 @@
idev->connection_rate = sci_port_get_max_allowed_speed(iport);
- /* / @todo Should I assign the port width by reading all of the phys on the port? */
- idev->device_port_width = 1;
-
return SCI_SUCCESS;
}