pcmcia: do not use io_req_t when calling pcmcia_request_io()
Instead of io_req_t, drivers are now requested to fill out
struct pcmcia_device *p_dev->resource[0,1] for up to two ioport
ranges. After a call to pcmcia_request_io(), the ports found there
are reserved, after calling pcmcia_request_configuration(), they may
be used.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
CC: Michael Buesch <mb@bu3sch.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
diff --git a/drivers/net/pcmcia/fmvj18x_cs.c b/drivers/net/pcmcia/fmvj18x_cs.c
index bba6369..6993044 100644
--- a/drivers/net/pcmcia/fmvj18x_cs.c
+++ b/drivers/net/pcmcia/fmvj18x_cs.c
@@ -248,9 +248,8 @@
lp->base = NULL;
/* The io structure describes IO port mapping */
- link->io.NumPorts1 = 32;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- link->io.IOAddrLines = 5;
+ link->resource[0]->end = 32;
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;
/* General socket configuration */
link->conf.Attributes = CONF_ENABLE_IRQ;
@@ -288,13 +287,13 @@
{ 0x3f8, 0x2f8, 0x3e8, 0x2e8, 0x0 };
for (i = 0; i < 5; i++) {
- link->io.BasePort2 = serial_base[i];
- link->io.Attributes2 = IO_DATA_PATH_WIDTH_8;
- if (link->io.BasePort2 == 0) {
- link->io.NumPorts2 = 0;
+ link->resource[1]->start = serial_base[i];
+ link->resource[1]->flags |= IO_DATA_PATH_WIDTH_8;
+ if (link->resource[1]->start == 0) {
+ link->resource[1]->end = 0;
printk(KERN_NOTICE "fmvj18x_cs: out of resource for serial\n");
}
- ret = pcmcia_request_io(link, &link->io);
+ ret = pcmcia_request_io(link);
if (ret == 0)
return ret;
}
@@ -310,8 +309,8 @@
0x380,0x3c0 only for ioport.
*/
for (ioaddr = 0x300; ioaddr < 0x3e0; ioaddr += 0x20) {
- link->io.BasePort1 = ioaddr;
- ret = pcmcia_request_io(link, &link->io);
+ link->resource[0]->start = ioaddr;
+ ret = pcmcia_request_io(link);
if (ret == 0) {
/* calculate ConfigIndex value */
link->conf.ConfigIndex =
@@ -345,6 +344,8 @@
dev_dbg(&link->dev, "fmvj18x_config\n");
+ link->io_lines = 5;
+
len = pcmcia_get_tuple(link, CISTPL_FUNCE, &buf);
kfree(buf);
@@ -363,20 +364,20 @@
/* MultiFunction Card */
link->conf.ConfigBase = 0x800;
link->conf.ConfigIndex = 0x47;
- link->io.NumPorts2 = 8;
+ link->resource[1]->end = 8;
}
break;
case MANFID_NEC:
cardtype = NEC; /* MultiFunction Card */
link->conf.ConfigBase = 0x800;
link->conf.ConfigIndex = 0x47;
- link->io.NumPorts2 = 8;
+ link->resource[1]->end = 8;
break;
case MANFID_KME:
cardtype = KME; /* MultiFunction Card */
link->conf.ConfigBase = 0x800;
link->conf.ConfigIndex = 0x47;
- link->io.NumPorts2 = 8;
+ link->resource[1]->end = 8;
break;
case MANFID_CONTEC:
cardtype = CONTEC;
@@ -417,14 +418,14 @@
}
}
- if (link->io.NumPorts2 != 0) {
+ if (link->resource[1]->end != 0) {
ret = mfc_try_io_port(link);
if (ret != 0) goto failed;
} else if (cardtype == UNGERMANN) {
ret = ungermann_try_io_port(link);
if (ret != 0) goto failed;
} else {
- ret = pcmcia_request_io(link, &link->io);
+ ret = pcmcia_request_io(link);
if (ret)
goto failed;
}