OMAP: Remove OMAP_IO_ADDRESS, use OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS instead
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.
Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.
In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c
index bbbaeb0..0680843 100644
--- a/arch/arm/mach-omap1/devices.c
+++ b/arch/arm/mach-omap1/devices.c
@@ -71,7 +71,7 @@
# define INT_DSP_MAILBOX1 INT_1610_DSP_MAILBOX1
#endif
-#define OMAP1_MBOX_BASE IO_ADDRESS(OMAP16XX_MAILBOX_BASE)
+#define OMAP1_MBOX_BASE OMAP1_IO_ADDRESS(OMAP16XX_MAILBOX_BASE)
static struct resource mbox_resources[] = {
{
diff --git a/arch/arm/mach-omap1/pm.h b/arch/arm/mach-omap1/pm.h
index 9ed5e2c..c4f05bd 100644
--- a/arch/arm/mach-omap1/pm.h
+++ b/arch/arm/mach-omap1/pm.h
@@ -39,11 +39,11 @@
* Register and offset definitions to be used in PM assembler code
* ----------------------------------------------------------------------------
*/
-#define CLKGEN_REG_ASM_BASE IO_ADDRESS(0xfffece00)
+#define CLKGEN_REG_ASM_BASE OMAP1_IO_ADDRESS(0xfffece00)
#define ARM_IDLECT1_ASM_OFFSET 0x04
#define ARM_IDLECT2_ASM_OFFSET 0x08
-#define TCMIF_ASM_BASE IO_ADDRESS(0xfffecc00)
+#define TCMIF_ASM_BASE OMAP1_IO_ADDRESS(0xfffecc00)
#define EMIFS_CONFIG_ASM_OFFSET 0x0c
#define EMIFF_SDRAM_CONFIG_ASM_OFFSET 0x20
diff --git a/arch/arm/mach-omap1/serial.c b/arch/arm/mach-omap1/serial.c
index f754cee..6f54b2c 100644
--- a/arch/arm/mach-omap1/serial.c
+++ b/arch/arm/mach-omap1/serial.c
@@ -64,7 +64,7 @@
static struct plat_serial8250_port serial_platform_data[] = {
{
- .membase = IO_ADDRESS(OMAP_UART1_BASE),
+ .membase = OMAP1_IO_ADDRESS(OMAP_UART1_BASE),
.mapbase = OMAP_UART1_BASE,
.irq = INT_UART1,
.flags = UPF_BOOT_AUTOCONF,
@@ -73,7 +73,7 @@
.uartclk = OMAP16XX_BASE_BAUD * 16,
},
{
- .membase = IO_ADDRESS(OMAP_UART2_BASE),
+ .membase = OMAP1_IO_ADDRESS(OMAP_UART2_BASE),
.mapbase = OMAP_UART2_BASE,
.irq = INT_UART2,
.flags = UPF_BOOT_AUTOCONF,
@@ -82,7 +82,7 @@
.uartclk = OMAP16XX_BASE_BAUD * 16,
},
{
- .membase = IO_ADDRESS(OMAP_UART3_BASE),
+ .membase = OMAP1_IO_ADDRESS(OMAP_UART3_BASE),
.mapbase = OMAP_UART3_BASE,
.irq = INT_UART3,
.flags = UPF_BOOT_AUTOCONF,
diff --git a/arch/arm/mach-omap1/sram.S b/arch/arm/mach-omap1/sram.S
index 261cdc4..7724e52 100644
--- a/arch/arm/mach-omap1/sram.S
+++ b/arch/arm/mach-omap1/sram.S
@@ -21,13 +21,13 @@
ENTRY(omap1_sram_reprogram_clock)
stmfd sp!, {r0 - r12, lr} @ save registers on stack
- mov r2, #IO_ADDRESS(DPLL_CTL) & 0xff000000
- orr r2, r2, #IO_ADDRESS(DPLL_CTL) & 0x00ff0000
- orr r2, r2, #IO_ADDRESS(DPLL_CTL) & 0x0000ff00
+ mov r2, #OMAP1_IO_ADDRESS(DPLL_CTL) & 0xff000000
+ orr r2, r2, #OMAP1_IO_ADDRESS(DPLL_CTL) & 0x00ff0000
+ orr r2, r2, #OMAP1_IO_ADDRESS(DPLL_CTL) & 0x0000ff00
- mov r3, #IO_ADDRESS(ARM_CKCTL) & 0xff000000
- orr r3, r3, #IO_ADDRESS(ARM_CKCTL) & 0x00ff0000
- orr r3, r3, #IO_ADDRESS(ARM_CKCTL) & 0x0000ff00
+ mov r3, #OMAP1_IO_ADDRESS(ARM_CKCTL) & 0xff000000
+ orr r3, r3, #OMAP1_IO_ADDRESS(ARM_CKCTL) & 0x00ff0000
+ orr r3, r3, #OMAP1_IO_ADDRESS(ARM_CKCTL) & 0x0000ff00
tst r0, #1 << 4 @ want lock mode?
beq newck @ nope
diff --git a/arch/arm/mach-omap1/time.c b/arch/arm/mach-omap1/time.c
index 4d56408..1be6a21 100644
--- a/arch/arm/mach-omap1/time.c
+++ b/arch/arm/mach-omap1/time.c
@@ -62,8 +62,8 @@
u32 read_tim; /* READ_TIM, R */
} omap_mpu_timer_regs_t;
-#define omap_mpu_timer_base(n) \
-((volatile omap_mpu_timer_regs_t*)IO_ADDRESS(OMAP_MPU_TIMER_BASE + \
+#define omap_mpu_timer_base(n) \
+((volatile omap_mpu_timer_regs_t*)OMAP1_IO_ADDRESS(OMAP_MPU_TIMER_BASE + \
(n)*OMAP_MPU_TIMER_OFFSET))
static inline unsigned long omap_mpu_timer_read(int nr)