msm: 9615: Add support for 9615 audio module
Define and expose ALSA FE/BE platform_devices in devices-9615 file and
board-9615 file will add them during initialization. Set regulator supply
for TABLA CODEC.
Change-Id: I78e9d31f4fa30fb1a313eb1edf6707031ec06174
Signed-off-by: Shiv Maliyappanahalli <smaliyap@codeaurora.org>
diff --git a/arch/arm/mach-msm/board-9615.c b/arch/arm/mach-msm/board-9615.c
index 8fe55ff..40cd9ea 100644
--- a/arch/arm/mach-msm/board-9615.c
+++ b/arch/arm/mach-msm/board-9615.c
@@ -15,6 +15,10 @@
#include <linux/io.h>
#include <linux/i2c.h>
#include <linux/slimbus/slimbus.h>
+#ifdef CONFIG_WCD9310_CODEC
+#include <linux/mfd/wcd9xxx/core.h>
+#include <linux/mfd/wcd9xxx/pdata.h>
+#endif
#include <linux/msm_ssbi.h>
#include <linux/memblock.h>
#include <linux/usb/android.h>
@@ -30,9 +34,11 @@
#include <mach/board.h>
#include <mach/msm_iomap.h>
#include <mach/gpio.h>
+#include <mach/socinfo.h>
#include <mach/msm_spi.h>
#include <mach/msm_bus_board.h>
#include <mach/msm_xo.h>
+#include <mach/dma.h>
#include "timer.h"
#include "devices.h"
#include "board-9615.h"
@@ -231,8 +237,96 @@
#endif
}
+#ifdef CONFIG_WCD9310_CODEC
+
+#define TABLA_INTERRUPT_BASE (NR_MSM_IRQS + NR_GPIO_IRQS)
+
+/* Micbias setting is based on 8660 CDP/MTP/FLUID requirement
+ * 4 micbiases are used to power various analog and digital
+ * microphones operating at 1800 mV. Technically, all micbiases
+ * can source from single cfilter since all microphones operate
+ * at the same voltage level. The arrangement below is to make
+ * sure all cfilters are exercised. LDO_H regulator ouput level
+ * does not need to be as high as 2.85V. It is choosen for
+ * microphone sensitivity purpose.
+ */
+
+static struct wcd9xxx_pdata tabla20_platform_data = {
+ .slimbus_slave_device = {
+ .name = "tabla-slave",
+ .e_addr = {0, 0, 0x60, 0, 0x17, 2},
+ },
+ .irq = 85,
+ .irq_base = TABLA_INTERRUPT_BASE,
+ .num_irqs = NR_WCD9XXX_IRQS,
+ .reset_gpio = 84,
+ .micbias = {
+ .ldoh_v = TABLA_LDOH_2P85_V,
+ .cfilt1_mv = 1800,
+ .cfilt2_mv = 1800,
+ .cfilt3_mv = 1800,
+ .bias1_cfilt_sel = TABLA_CFILT1_SEL,
+ .bias2_cfilt_sel = TABLA_CFILT2_SEL,
+ .bias3_cfilt_sel = TABLA_CFILT3_SEL,
+ .bias4_cfilt_sel = TABLA_CFILT3_SEL,
+ },
+ .regulator = {
+ {
+ .name = "CDC_VDD_CP",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .optimum_uA = WCD9XXX_CDC_VDDA_CP_CUR_MAX,
+ },
+ {
+ .name = "CDC_VDDA_RX",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .optimum_uA = WCD9XXX_CDC_VDDA_RX_CUR_MAX,
+ },
+ {
+ .name = "CDC_VDDA_TX",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .optimum_uA = WCD9XXX_CDC_VDDA_TX_CUR_MAX,
+ },
+ {
+ .name = "VDDIO_CDC",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .optimum_uA = WCD9XXX_VDDIO_CDC_CUR_MAX,
+ },
+ {
+ .name = "VDDD_CDC_D",
+ .min_uV = 1225000,
+ .max_uV = 1225000,
+ .optimum_uA = WCD9XXX_VDDD_CDC_D_CUR_MAX,
+ },
+ {
+ .name = "CDC_VDDA_A_1P2V",
+ .min_uV = 1225000,
+ .max_uV = 1225000,
+ .optimum_uA = WCD9XXX_VDDD_CDC_A_CUR_MAX,
+ },
+ },
+};
+
+static struct slim_device msm_slim_tabla20 = {
+ .name = "tabla2x-slim",
+ .e_addr = {0, 1, 0x60, 0, 0x17, 2},
+ .dev = {
+ .platform_data = &tabla20_platform_data,
+ },
+};
+#endif
+
static struct slim_boardinfo msm_slim_devices[] = {
/* add slimbus slaves as needed */
+#ifdef CONFIG_WCD9310_CODEC
+ {
+ .bus_num = 1,
+ .slim_slave = &msm_slim_tabla20,
+ },
+#endif
};
static struct msm_spi_platform_data msm9615_qup_spi_gsbi3_pdata = {
@@ -545,6 +639,26 @@
&msm_device_rng,
#endif
+ &msm_pcm,
+ &msm_multi_ch_pcm,
+ &msm_pcm_routing,
+ &msm_cpudai0,
+ &msm_cpudai1,
+ &msm_cpudai_bt_rx,
+ &msm_cpudai_bt_tx,
+ &msm_cpu_fe,
+ &msm_stub_codec,
+ &msm_voice,
+ &msm_voip,
+ &msm_pcm_hostless,
+ &msm_cpudai_afe_01_rx,
+ &msm_cpudai_afe_01_tx,
+ &msm_cpudai_afe_02_rx,
+ &msm_cpudai_afe_02_tx,
+ &msm_pcm_afe,
+ &msm_cpudai_auxpcm_rx,
+ &msm_cpudai_auxpcm_tx,
+
#if defined(CONFIG_CRYPTO_DEV_QCRYPTO) || \
defined(CONFIG_CRYPTO_DEV_QCRYPTO_MODULE)
&msm9615_qcrypto_device,