sh: kfr2r09 board support - LCDC panel
This patch adds support for the WQVGA LCD display used by
the KFR2R09 board. The LCD module is a TX07D34VM0AAA made
by Hitachi, and this module is made up by a R61517 chip
together with a 240x400 pixel display. The screen is
attached to the SuperH Mobile LCDC using a 18-bit SYS bus.
The register settings used by the SYS panel setup code are
based on an out-of-tree driver which apart from duplicating
all LCDC driver code and writing to non-existing hardware
registers also never was posted for upstream merge.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
diff --git a/arch/sh/boards/mach-kfr2r09/setup.c b/arch/sh/boards/mach-kfr2r09/setup.c
index bf5f8f8..1355080 100644
--- a/arch/sh/boards/mach-kfr2r09/setup.c
+++ b/arch/sh/boards/mach-kfr2r09/setup.c
@@ -15,11 +15,13 @@
#include <linux/clk.h>
#include <linux/gpio.h>
#include <linux/input.h>
+#include <video/sh_mobile_lcdc.h>
#include <asm/clock.h>
#include <asm/machvec.h>
#include <asm/io.h>
#include <asm/sh_keysc.h>
#include <cpu/sh7724.h>
+#include <mach/kfr2r09.h>
static struct mtd_partition kfr2r09_nor_flash_partitions[] =
{
@@ -97,9 +99,70 @@
},
};
+static struct sh_mobile_lcdc_info kfr2r09_sh_lcdc_info = {
+ .clock_source = LCDC_CLK_BUS,
+ .ch[0] = {
+ .chan = LCDC_CHAN_MAINLCD,
+ .bpp = 16,
+ .interface_type = SYS18,
+ .clock_divider = 6,
+ .flags = LCDC_FLAGS_DWPOL,
+ .lcd_cfg = {
+ .name = "TX07D34VM0AAA",
+ .xres = 240,
+ .yres = 400,
+ .left_margin = 0,
+ .right_margin = 16,
+ .hsync_len = 8,
+ .upper_margin = 0,
+ .lower_margin = 1,
+ .vsync_len = 1,
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ },
+ .lcd_size_cfg = {
+ .width = 35,
+ .height = 58,
+ },
+ .board_cfg = {
+ .setup_sys = kfr2r09_lcd_setup,
+ .display_on = kfr2r09_lcd_on,
+ .display_off = kfr2r09_lcd_off,
+ },
+ .sys_bus_cfg = {
+ .ldmt2r = 0x07010904,
+ .ldmt3r = 0x14012914,
+ /* set 1s delay to encourage fsync() */
+ .deferred_io_msec = 1000,
+ },
+ }
+};
+
+static struct resource kfr2r09_sh_lcdc_resources[] = {
+ [0] = {
+ .name = "LCDC",
+ .start = 0xfe940000, /* P4-only space */
+ .end = 0xfe941fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = 106,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device kfr2r09_sh_lcdc_device = {
+ .name = "sh_mobile_lcdc_fb",
+ .num_resources = ARRAY_SIZE(kfr2r09_sh_lcdc_resources),
+ .resource = kfr2r09_sh_lcdc_resources,
+ .dev = {
+ .platform_data = &kfr2r09_sh_lcdc_info,
+ },
+};
+
static struct platform_device *kfr2r09_devices[] __initdata = {
&kfr2r09_nor_flash_device,
&kfr2r09_sh_keysc_device,
+ &kfr2r09_sh_lcdc_device,
};
#define BSC_CS0BCR 0xfec10004
@@ -128,6 +191,37 @@
gpio_request(GPIO_FN_KEYIN4, NULL);
gpio_request(GPIO_FN_KEYOUT5_IN5, NULL);
+ /* setup LCDC pins for SYS panel */
+ gpio_request(GPIO_FN_LCDD17, NULL);
+ gpio_request(GPIO_FN_LCDD16, NULL);
+ gpio_request(GPIO_FN_LCDD15, NULL);
+ gpio_request(GPIO_FN_LCDD14, NULL);
+ gpio_request(GPIO_FN_LCDD13, NULL);
+ gpio_request(GPIO_FN_LCDD12, NULL);
+ gpio_request(GPIO_FN_LCDD11, NULL);
+ gpio_request(GPIO_FN_LCDD10, NULL);
+ gpio_request(GPIO_FN_LCDD9, NULL);
+ gpio_request(GPIO_FN_LCDD8, NULL);
+ gpio_request(GPIO_FN_LCDD7, NULL);
+ gpio_request(GPIO_FN_LCDD6, NULL);
+ gpio_request(GPIO_FN_LCDD5, NULL);
+ gpio_request(GPIO_FN_LCDD4, NULL);
+ gpio_request(GPIO_FN_LCDD3, NULL);
+ gpio_request(GPIO_FN_LCDD2, NULL);
+ gpio_request(GPIO_FN_LCDD1, NULL);
+ gpio_request(GPIO_FN_LCDD0, NULL);
+ gpio_request(GPIO_FN_LCDRS, NULL); /* LCD_RS */
+ gpio_request(GPIO_FN_LCDCS, NULL); /* LCD_CS/ */
+ gpio_request(GPIO_FN_LCDRD, NULL); /* LCD_RD/ */
+ gpio_request(GPIO_FN_LCDWR, NULL); /* LCD_WR/ */
+ gpio_request(GPIO_FN_LCDVSYN, NULL); /* LCD_VSYNC */
+ gpio_request(GPIO_PTE4, NULL); /* LCD_RST/ */
+ gpio_direction_output(GPIO_PTE4, 1);
+ gpio_request(GPIO_PTF4, NULL); /* PROTECT/ */
+ gpio_direction_output(GPIO_PTF4, 1);
+ gpio_request(GPIO_PTU0, NULL); /* LEDSTDBY/ */
+ gpio_direction_output(GPIO_PTU0, 1);
+
return platform_add_devices(kfr2r09_devices,
ARRAY_SIZE(kfr2r09_devices));
}