| #ifndef NET2280_H |
| #define NET2280_H |
| /* |
| * NetChip 2280 high/full speed USB device controller. |
| * Unlike many such controllers, this one talks PCI. |
| */ |
| |
| /* |
| * Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com) |
| * Copyright (C) 2003 David Brownell |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA |
| */ |
| |
| /*-------------------------------------------------------------------------*/ |
| |
| /* NET2280 MEMORY MAPPED REGISTERS |
| * |
| * The register layout came from the chip documentation, and the bit |
| * number definitions were extracted from chip specification. |
| * |
| * Use the shift operator ('<<') to build bit masks, with readl/writel |
| * to access the registers through PCI. |
| */ |
| |
| /* main registers, BAR0 + 0x0000 */ |
| struct net2280_regs { |
| /* offset 0x0000 */ |
| __le32 devinit; |
| #define LOCAL_CLOCK_FREQUENCY 8 |
| #define FORCE_PCI_RESET 7 |
| #define PCI_ID 6 |
| #define PCI_ENABLE 5 |
| #define FIFO_SOFT_RESET 4 |
| #define CFG_SOFT_RESET 3 |
| #define PCI_SOFT_RESET 2 |
| #define USB_SOFT_RESET 1 |
| #define M8051_RESET 0 |
| __le32 eectl; |
| #define EEPROM_ADDRESS_WIDTH 23 |
| #define EEPROM_CHIP_SELECT_ACTIVE 22 |
| #define EEPROM_PRESENT 21 |
| #define EEPROM_VALID 20 |
| #define EEPROM_BUSY 19 |
| #define EEPROM_CHIP_SELECT_ENABLE 18 |
| #define EEPROM_BYTE_READ_START 17 |
| #define EEPROM_BYTE_WRITE_START 16 |
| #define EEPROM_READ_DATA 8 |
| #define EEPROM_WRITE_DATA 0 |
| __le32 eeclkfreq; |
| u32 _unused0; |
| /* offset 0x0010 */ |
| |
| __le32 pciirqenb0; /* interrupt PCI master ... */ |
| #define SETUP_PACKET_INTERRUPT_ENABLE 7 |
| #define ENDPOINT_F_INTERRUPT_ENABLE 6 |
| #define ENDPOINT_E_INTERRUPT_ENABLE 5 |
| #define ENDPOINT_D_INTERRUPT_ENABLE 4 |
| #define ENDPOINT_C_INTERRUPT_ENABLE 3 |
| #define ENDPOINT_B_INTERRUPT_ENABLE 2 |
| #define ENDPOINT_A_INTERRUPT_ENABLE 1 |
| #define ENDPOINT_0_INTERRUPT_ENABLE 0 |
| __le32 pciirqenb1; |
| #define PCI_INTERRUPT_ENABLE 31 |
| #define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 |
| #define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 |
| #define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 |
| #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 |
| #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 |
| #define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18 |
| #define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 |
| #define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 |
| #define GPIO_INTERRUPT_ENABLE 13 |
| #define DMA_D_INTERRUPT_ENABLE 12 |
| #define DMA_C_INTERRUPT_ENABLE 11 |
| #define DMA_B_INTERRUPT_ENABLE 10 |
| #define DMA_A_INTERRUPT_ENABLE 9 |
| #define EEPROM_DONE_INTERRUPT_ENABLE 8 |
| #define VBUS_INTERRUPT_ENABLE 7 |
| #define CONTROL_STATUS_INTERRUPT_ENABLE 6 |
| #define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 |
| #define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 |
| #define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 |
| #define RESUME_INTERRUPT_ENABLE 1 |
| #define SOF_INTERRUPT_ENABLE 0 |
| __le32 cpu_irqenb0; /* ... or onboard 8051 */ |
| #define SETUP_PACKET_INTERRUPT_ENABLE 7 |
| #define ENDPOINT_F_INTERRUPT_ENABLE 6 |
| #define ENDPOINT_E_INTERRUPT_ENABLE 5 |
| #define ENDPOINT_D_INTERRUPT_ENABLE 4 |
| #define ENDPOINT_C_INTERRUPT_ENABLE 3 |
| #define ENDPOINT_B_INTERRUPT_ENABLE 2 |
| #define ENDPOINT_A_INTERRUPT_ENABLE 1 |
| #define ENDPOINT_0_INTERRUPT_ENABLE 0 |
| __le32 cpu_irqenb1; |
| #define CPU_INTERRUPT_ENABLE 31 |
| #define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 |
| #define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 |
| #define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 |
| #define PCI_INTA_INTERRUPT_ENABLE 24 |
| #define PCI_PME_INTERRUPT_ENABLE 23 |
| #define PCI_SERR_INTERRUPT_ENABLE 22 |
| #define PCI_PERR_INTERRUPT_ENABLE 21 |
| #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 |
| #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 |
| #define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 |
| #define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 |
| #define GPIO_INTERRUPT_ENABLE 13 |
| #define DMA_D_INTERRUPT_ENABLE 12 |
| #define DMA_C_INTERRUPT_ENABLE 11 |
| #define DMA_B_INTERRUPT_ENABLE 10 |
| #define DMA_A_INTERRUPT_ENABLE 9 |
| #define EEPROM_DONE_INTERRUPT_ENABLE 8 |
| #define VBUS_INTERRUPT_ENABLE 7 |
| #define CONTROL_STATUS_INTERRUPT_ENABLE 6 |
| #define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 |
| #define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 |
| #define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 |
| #define RESUME_INTERRUPT_ENABLE 1 |
| #define SOF_INTERRUPT_ENABLE 0 |
| |
| /* offset 0x0020 */ |
| u32 _unused1; |
| __le32 usbirqenb1; |
| #define USB_INTERRUPT_ENABLE 31 |
| #define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 |
| #define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 |
| #define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 |
| #define PCI_INTA_INTERRUPT_ENABLE 24 |
| #define PCI_PME_INTERRUPT_ENABLE 23 |
| #define PCI_SERR_INTERRUPT_ENABLE 22 |
| #define PCI_PERR_INTERRUPT_ENABLE 21 |
| #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 |
| #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 |
| #define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 |
| #define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 |
| #define GPIO_INTERRUPT_ENABLE 13 |
| #define DMA_D_INTERRUPT_ENABLE 12 |
| #define DMA_C_INTERRUPT_ENABLE 11 |
| #define DMA_B_INTERRUPT_ENABLE 10 |
| #define DMA_A_INTERRUPT_ENABLE 9 |
| #define EEPROM_DONE_INTERRUPT_ENABLE 8 |
| #define VBUS_INTERRUPT_ENABLE 7 |
| #define CONTROL_STATUS_INTERRUPT_ENABLE 6 |
| #define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 |
| #define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 |
| #define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 |
| #define RESUME_INTERRUPT_ENABLE 1 |
| #define SOF_INTERRUPT_ENABLE 0 |
| __le32 irqstat0; |
| #define INTA_ASSERTED 12 |
| #define SETUP_PACKET_INTERRUPT 7 |
| #define ENDPOINT_F_INTERRUPT 6 |
| #define ENDPOINT_E_INTERRUPT 5 |
| #define ENDPOINT_D_INTERRUPT 4 |
| #define ENDPOINT_C_INTERRUPT 3 |
| #define ENDPOINT_B_INTERRUPT 2 |
| #define ENDPOINT_A_INTERRUPT 1 |
| #define ENDPOINT_0_INTERRUPT 0 |
| __le32 irqstat1; |
| #define POWER_STATE_CHANGE_INTERRUPT 27 |
| #define PCI_ARBITER_TIMEOUT_INTERRUPT 26 |
| #define PCI_PARITY_ERROR_INTERRUPT 25 |
| #define PCI_INTA_INTERRUPT 24 |
| #define PCI_PME_INTERRUPT 23 |
| #define PCI_SERR_INTERRUPT 22 |
| #define PCI_PERR_INTERRUPT 21 |
| #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20 |
| #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19 |
| #define PCI_RETRY_ABORT_INTERRUPT 17 |
| #define PCI_MASTER_CYCLE_DONE_INTERRUPT 16 |
| #define GPIO_INTERRUPT 13 |
| #define DMA_D_INTERRUPT 12 |
| #define DMA_C_INTERRUPT 11 |
| #define DMA_B_INTERRUPT 10 |
| #define DMA_A_INTERRUPT 9 |
| #define EEPROM_DONE_INTERRUPT 8 |
| #define VBUS_INTERRUPT 7 |
| #define CONTROL_STATUS_INTERRUPT 6 |
| #define ROOT_PORT_RESET_INTERRUPT 4 |
| #define SUSPEND_REQUEST_INTERRUPT 3 |
| #define SUSPEND_REQUEST_CHANGE_INTERRUPT 2 |
| #define RESUME_INTERRUPT 1 |
| #define SOF_INTERRUPT 0 |
| /* offset 0x0030 */ |
| __le32 idxaddr; |
| __le32 idxdata; |
| __le32 fifoctl; |
| #define PCI_BASE2_RANGE 16 |
| #define IGNORE_FIFO_AVAILABILITY 3 |
| #define PCI_BASE2_SELECT 2 |
| #define FIFO_CONFIGURATION_SELECT 0 |
| u32 _unused2; |
| /* offset 0x0040 */ |
| __le32 memaddr; |
| #define START 28 |
| #define DIRECTION 27 |
| #define FIFO_DIAGNOSTIC_SELECT 24 |
| #define MEMORY_ADDRESS 0 |
| __le32 memdata0; |
| __le32 memdata1; |
| u32 _unused3; |
| /* offset 0x0050 */ |
| __le32 gpioctl; |
| #define GPIO3_LED_SELECT 12 |
| #define GPIO3_INTERRUPT_ENABLE 11 |
| #define GPIO2_INTERRUPT_ENABLE 10 |
| #define GPIO1_INTERRUPT_ENABLE 9 |
| #define GPIO0_INTERRUPT_ENABLE 8 |
| #define GPIO3_OUTPUT_ENABLE 7 |
| #define GPIO2_OUTPUT_ENABLE 6 |
| #define GPIO1_OUTPUT_ENABLE 5 |
| #define GPIO0_OUTPUT_ENABLE 4 |
| #define GPIO3_DATA 3 |
| #define GPIO2_DATA 2 |
| #define GPIO1_DATA 1 |
| #define GPIO0_DATA 0 |
| __le32 gpiostat; |
| #define GPIO3_INTERRUPT 3 |
| #define GPIO2_INTERRUPT 2 |
| #define GPIO1_INTERRUPT 1 |
| #define GPIO0_INTERRUPT 0 |
| } __packed; |
| |
| /* usb control, BAR0 + 0x0080 */ |
| struct net2280_usb_regs { |
| /* offset 0x0080 */ |
| __le32 stdrsp; |
| #define STALL_UNSUPPORTED_REQUESTS 31 |
| #define SET_TEST_MODE 16 |
| #define GET_OTHER_SPEED_CONFIGURATION 15 |
| #define GET_DEVICE_QUALIFIER 14 |
| #define SET_ADDRESS 13 |
| #define ENDPOINT_SET_CLEAR_HALT 12 |
| #define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11 |
| #define GET_STRING_DESCRIPTOR_2 10 |
| #define GET_STRING_DESCRIPTOR_1 9 |
| #define GET_STRING_DESCRIPTOR_0 8 |
| #define GET_SET_INTERFACE 6 |
| #define GET_SET_CONFIGURATION 5 |
| #define GET_CONFIGURATION_DESCRIPTOR 4 |
| #define GET_DEVICE_DESCRIPTOR 3 |
| #define GET_ENDPOINT_STATUS 2 |
| #define GET_INTERFACE_STATUS 1 |
| #define GET_DEVICE_STATUS 0 |
| __le32 prodvendid; |
| #define PRODUCT_ID 16 |
| #define VENDOR_ID 0 |
| __le32 relnum; |
| __le32 usbctl; |
| #define SERIAL_NUMBER_INDEX 16 |
| #define PRODUCT_ID_STRING_ENABLE 13 |
| #define VENDOR_ID_STRING_ENABLE 12 |
| #define USB_ROOT_PORT_WAKEUP_ENABLE 11 |
| #define VBUS_PIN 10 |
| #define TIMED_DISCONNECT 9 |
| #define SUSPEND_IMMEDIATELY 7 |
| #define SELF_POWERED_USB_DEVICE 6 |
| #define REMOTE_WAKEUP_SUPPORT 5 |
| #define PME_POLARITY 4 |
| #define USB_DETECT_ENABLE 3 |
| #define PME_WAKEUP_ENABLE 2 |
| #define DEVICE_REMOTE_WAKEUP_ENABLE 1 |
| #define SELF_POWERED_STATUS 0 |
| /* offset 0x0090 */ |
| __le32 usbstat; |
| #define HIGH_SPEED 7 |
| #define FULL_SPEED 6 |
| #define GENERATE_RESUME 5 |
| #define GENERATE_DEVICE_REMOTE_WAKEUP 4 |
| __le32 xcvrdiag; |
| #define FORCE_HIGH_SPEED_MODE 31 |
| #define FORCE_FULL_SPEED_MODE 30 |
| #define USB_TEST_MODE 24 |
| #define LINE_STATE 16 |
| #define TRANSCEIVER_OPERATION_MODE 2 |
| #define TRANSCEIVER_SELECT 1 |
| #define TERMINATION_SELECT 0 |
| __le32 setup0123; |
| __le32 setup4567; |
| /* offset 0x0090 */ |
| u32 _unused0; |
| __le32 ouraddr; |
| #define FORCE_IMMEDIATE 7 |
| #define OUR_USB_ADDRESS 0 |
| __le32 ourconfig; |
| } __packed; |
| |
| /* pci control, BAR0 + 0x0100 */ |
| struct net2280_pci_regs { |
| /* offset 0x0100 */ |
| __le32 pcimstctl; |
| #define PCI_ARBITER_PARK_SELECT 13 |
| #define PCI_MULTI LEVEL_ARBITER 12 |
| #define PCI_RETRY_ABORT_ENABLE 11 |
| #define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10 |
| #define DMA_READ_MULTIPLE_ENABLE 9 |
| #define DMA_READ_LINE_ENABLE 8 |
| #define PCI_MASTER_COMMAND_SELECT 6 |
| #define MEM_READ_OR_WRITE 0 |
| #define IO_READ_OR_WRITE 1 |
| #define CFG_READ_OR_WRITE 2 |
| #define PCI_MASTER_START 5 |
| #define PCI_MASTER_READ_WRITE 4 |
| #define PCI_MASTER_WRITE 0 |
| #define PCI_MASTER_READ 1 |
| #define PCI_MASTER_BYTE_WRITE_ENABLES 0 |
| __le32 pcimstaddr; |
| __le32 pcimstdata; |
| __le32 pcimststat; |
| #define PCI_ARBITER_CLEAR 2 |
| #define PCI_EXTERNAL_ARBITER 1 |
| #define PCI_HOST_MODE 0 |
| } __packed; |
| |
| /* dma control, BAR0 + 0x0180 ... array of four structs like this, |
| * for channels 0..3. see also struct net2280_dma: descriptor |
| * that can be loaded into some of these registers. |
| */ |
| struct net2280_dma_regs { /* [11.7] */ |
| /* offset 0x0180, 0x01a0, 0x01c0, 0x01e0, */ |
| __le32 dmactl; |
| #define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25 |
| #define DMA_CLEAR_COUNT_ENABLE 21 |
| #define DESCRIPTOR_POLLING_RATE 19 |
| #define POLL_CONTINUOUS 0 |
| #define POLL_1_USEC 1 |
| #define POLL_100_USEC 2 |
| #define POLL_1_MSEC 3 |
| #define DMA_VALID_BIT_POLLING_ENABLE 18 |
| #define DMA_VALID_BIT_ENABLE 17 |
| #define DMA_SCATTER_GATHER_ENABLE 16 |
| #define DMA_OUT_AUTO_START_ENABLE 4 |
| #define DMA_PREEMPT_ENABLE 3 |
| #define DMA_FIFO_VALIDATE 2 |
| #define DMA_ENABLE 1 |
| #define DMA_ADDRESS_HOLD 0 |
| __le32 dmastat; |
| #define DMA_SCATTER_GATHER_DONE_INTERRUPT 25 |
| #define DMA_TRANSACTION_DONE_INTERRUPT 24 |
| #define DMA_ABORT 1 |
| #define DMA_START 0 |
| u32 _unused0[2]; |
| /* offset 0x0190, 0x01b0, 0x01d0, 0x01f0, */ |
| __le32 dmacount; |
| #define VALID_BIT 31 |
| #define DMA_DIRECTION 30 |
| #define DMA_DONE_INTERRUPT_ENABLE 29 |
| #define END_OF_CHAIN 28 |
| #define DMA_BYTE_COUNT_MASK ((1<<24)-1) |
| #define DMA_BYTE_COUNT 0 |
| __le32 dmaaddr; |
| __le32 dmadesc; |
| u32 _unused1; |
| } __packed; |
| |
| /* dedicated endpoint registers, BAR0 + 0x0200 */ |
| |
| struct net2280_dep_regs { /* [11.8] */ |
| /* offset 0x0200, 0x0210, 0x220, 0x230, 0x240 */ |
| __le32 dep_cfg; |
| /* offset 0x0204, 0x0214, 0x224, 0x234, 0x244 */ |
| __le32 dep_rsp; |
| u32 _unused[2]; |
| } __packed; |
| |
| /* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs |
| * like this, for ep0 then the configurable endpoints A..F |
| * ep0 reserved for control; E and F have only 64 bytes of fifo |
| */ |
| struct net2280_ep_regs { /* [11.9] */ |
| /* offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0 */ |
| __le32 ep_cfg; |
| #define ENDPOINT_BYTE_COUNT 16 |
| #define ENDPOINT_ENABLE 10 |
| #define ENDPOINT_TYPE 8 |
| #define ENDPOINT_DIRECTION 7 |
| #define ENDPOINT_NUMBER 0 |
| __le32 ep_rsp; |
| #define SET_NAK_OUT_PACKETS 15 |
| #define SET_EP_HIDE_STATUS_PHASE 14 |
| #define SET_EP_FORCE_CRC_ERROR 13 |
| #define SET_INTERRUPT_MODE 12 |
| #define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11 |
| #define SET_NAK_OUT_PACKETS_MODE 10 |
| #define SET_ENDPOINT_TOGGLE 9 |
| #define SET_ENDPOINT_HALT 8 |
| #define CLEAR_NAK_OUT_PACKETS 7 |
| #define CLEAR_EP_HIDE_STATUS_PHASE 6 |
| #define CLEAR_EP_FORCE_CRC_ERROR 5 |
| #define CLEAR_INTERRUPT_MODE 4 |
| #define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3 |
| #define CLEAR_NAK_OUT_PACKETS_MODE 2 |
| #define CLEAR_ENDPOINT_TOGGLE 1 |
| #define CLEAR_ENDPOINT_HALT 0 |
| __le32 ep_irqenb; |
| #define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6 |
| #define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5 |
| #define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3 |
| #define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2 |
| #define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1 |
| #define DATA_IN_TOKEN_INTERRUPT_ENABLE 0 |
| __le32 ep_stat; |
| #define FIFO_VALID_COUNT 24 |
| #define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22 |
| #define TIMEOUT 21 |
| #define USB_STALL_SENT 20 |
| #define USB_IN_NAK_SENT 19 |
| #define USB_IN_ACK_RCVD 18 |
| #define USB_OUT_PING_NAK_SENT 17 |
| #define USB_OUT_ACK_SENT 16 |
| #define FIFO_OVERFLOW 13 |
| #define FIFO_UNDERFLOW 12 |
| #define FIFO_FULL 11 |
| #define FIFO_EMPTY 10 |
| #define FIFO_FLUSH 9 |
| #define SHORT_PACKET_OUT_DONE_INTERRUPT 6 |
| #define SHORT_PACKET_TRANSFERRED_INTERRUPT 5 |
| #define NAK_OUT_PACKETS 4 |
| #define DATA_PACKET_RECEIVED_INTERRUPT 3 |
| #define DATA_PACKET_TRANSMITTED_INTERRUPT 2 |
| #define DATA_OUT_PING_TOKEN_INTERRUPT 1 |
| #define DATA_IN_TOKEN_INTERRUPT 0 |
| /* offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0 */ |
| __le32 ep_avail; |
| __le32 ep_data; |
| u32 _unused0[2]; |
| } __packed; |
| |
| struct net2280_reg_write { |
| __le16 port; |
| __le32 addr; |
| __le32 val; |
| } __packed; |
| |
| struct net2280_reg_read { |
| __le16 port; |
| __le32 addr; |
| } __packed; |
| #endif /* NET2280_H */ |