iwlwifi: move apm_init to start_hw
This is transport related
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
diff --git a/drivers/net/wireless/iwlwifi/iwl-trans-pcie.c b/drivers/net/wireless/iwlwifi/iwl-trans-pcie.c
index d1ab57a..335d4b1 100644
--- a/drivers/net/wireless/iwlwifi/iwl-trans-pcie.c
+++ b/drivers/net/wireless/iwlwifi/iwl-trans-pcie.c
@@ -74,6 +74,7 @@
#include "iwl-shared.h"
#include "iwl-eeprom.h"
#include "iwl-agn-hw.h"
+#include "iwl-core.h"
static int iwl_trans_rx_alloc(struct iwl_trans *trans)
{
@@ -631,13 +632,95 @@
~APMG_PS_CTRL_MSK_PWR_SRC);
}
+/*
+ * Start up NIC's basic functionality after it has been reset
+ * (e.g. after platform boot, or shutdown via iwl_apm_stop())
+ * NOTE: This does not load uCode nor start the embedded processor
+ */
+static int iwl_apm_init(struct iwl_trans *trans)
+{
+ int ret = 0;
+ IWL_DEBUG_INFO(trans, "Init card's basic functions\n");
+
+ /*
+ * Use "set_bit" below rather than "write", to preserve any hardware
+ * bits already set by default after reset.
+ */
+
+ /* Disable L0S exit timer (platform NMI Work/Around) */
+ iwl_set_bit(trans, CSR_GIO_CHICKEN_BITS,
+ CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER);
+
+ /*
+ * Disable L0s without affecting L1;
+ * don't wait for ICH L0s (ICH bug W/A)
+ */
+ iwl_set_bit(trans, CSR_GIO_CHICKEN_BITS,
+ CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX);
+
+ /* Set FH wait threshold to maximum (HW error during stress W/A) */
+ iwl_set_bit(trans, CSR_DBG_HPET_MEM_REG, CSR_DBG_HPET_MEM_REG_VAL);
+
+ /*
+ * Enable HAP INTA (interrupt from management bus) to
+ * wake device's PCI Express link L1a -> L0s
+ */
+ iwl_set_bit(trans, CSR_HW_IF_CONFIG_REG,
+ CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A);
+
+ bus_apm_config(bus(trans));
+
+ /* Configure analog phase-lock-loop before activating to D0A */
+ if (cfg(trans)->base_params->pll_cfg_val)
+ iwl_set_bit(trans, CSR_ANA_PLL_CFG,
+ cfg(trans)->base_params->pll_cfg_val);
+
+ /*
+ * Set "initialization complete" bit to move adapter from
+ * D0U* --> D0A* (powered-up active) state.
+ */
+ iwl_set_bit(trans, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
+
+ /*
+ * Wait for clock stabilization; once stabilized, access to
+ * device-internal resources is supported, e.g. iwl_write_prph()
+ * and accesses to uCode SRAM.
+ */
+ ret = iwl_poll_bit(trans, CSR_GP_CNTRL,
+ CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY,
+ CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY, 25000);
+ if (ret < 0) {
+ IWL_DEBUG_INFO(trans, "Failed to init the card\n");
+ goto out;
+ }
+
+ /*
+ * Enable DMA clock and wait for it to stabilize.
+ *
+ * Write to "CLK_EN_REG"; "1" bits enable clocks, while "0" bits
+ * do not disable clocks. This preserves any hardware bits already
+ * set by default in "CLK_CTRL_REG" after reset.
+ */
+ iwl_write_prph(trans, APMG_CLK_EN_REG, APMG_CLK_VAL_DMA_CLK_RQT);
+ udelay(20);
+
+ /* Disable L1-Active */
+ iwl_set_bits_prph(trans, APMG_PCIDEV_STT_REG,
+ APMG_PCIDEV_STT_VAL_L1_ACT_DIS);
+
+ set_bit(STATUS_DEVICE_ENABLED, &trans->shrd->status);
+
+out:
+ return ret;
+}
+
static int iwl_nic_init(struct iwl_trans *trans)
{
unsigned long flags;
/* nic_init */
spin_lock_irqsave(&trans->shrd->lock, flags);
- iwl_apm_init(priv(trans));
+ iwl_apm_init(trans);
/* Set interrupt coalescing calibration timer to default (512 usecs) */
iwl_write8(trans, CSR_INT_COALESCING,
@@ -1267,6 +1350,9 @@
IWL_ERR(trans, "Error while preparing HW: %d", err);
goto error;
}
+
+ iwl_apm_init(trans);
+
return err;
error: