|  | /* | 
|  | * drivers/usb/host/ehci-orion.c | 
|  | * | 
|  | * Tzachi Perelstein <tzachi@marvell.com> | 
|  | * | 
|  | * This file is licensed under  the terms of the GNU General Public | 
|  | * License version 2. This program is licensed "as is" without any | 
|  | * warranty of any kind, whether express or implied. | 
|  | */ | 
|  |  | 
|  | #include <linux/kernel.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/platform_device.h> | 
|  | #include <linux/mbus.h> | 
|  | #include <plat/ehci-orion.h> | 
|  |  | 
|  | #define rdl(off)	__raw_readl(hcd->regs + (off)) | 
|  | #define wrl(off, val)	__raw_writel((val), hcd->regs + (off)) | 
|  |  | 
|  | #define USB_CMD			0x140 | 
|  | #define USB_MODE		0x1a8 | 
|  | #define USB_CAUSE		0x310 | 
|  | #define USB_MASK		0x314 | 
|  | #define USB_WINDOW_CTRL(i)	(0x320 + ((i) << 4)) | 
|  | #define USB_WINDOW_BASE(i)	(0x324 + ((i) << 4)) | 
|  | #define USB_IPG			0x360 | 
|  | #define USB_PHY_PWR_CTRL	0x400 | 
|  | #define USB_PHY_TX_CTRL		0x420 | 
|  | #define USB_PHY_RX_CTRL		0x430 | 
|  | #define USB_PHY_IVREF_CTRL	0x440 | 
|  | #define USB_PHY_TST_GRP_CTRL	0x450 | 
|  |  | 
|  | /* | 
|  | * Implement Orion USB controller specification guidelines | 
|  | */ | 
|  | static void orion_usb_phy_v1_setup(struct usb_hcd *hcd) | 
|  | { | 
|  | /* The below GLs are according to the Orion Errata document */ | 
|  | /* | 
|  | * Clear interrupt cause and mask | 
|  | */ | 
|  | wrl(USB_CAUSE, 0); | 
|  | wrl(USB_MASK, 0); | 
|  |  | 
|  | /* | 
|  | * Reset controller | 
|  | */ | 
|  | wrl(USB_CMD, rdl(USB_CMD) | 0x2); | 
|  | while (rdl(USB_CMD) & 0x2); | 
|  |  | 
|  | /* | 
|  | * GL# USB-10: Set IPG for non start of frame packets | 
|  | * Bits[14:8]=0xc | 
|  | */ | 
|  | wrl(USB_IPG, (rdl(USB_IPG) & ~0x7f00) | 0xc00); | 
|  |  | 
|  | /* | 
|  | * GL# USB-9: USB 2.0 Power Control | 
|  | * BG_VSEL[7:6]=0x1 | 
|  | */ | 
|  | wrl(USB_PHY_PWR_CTRL, (rdl(USB_PHY_PWR_CTRL) & ~0xc0)| 0x40); | 
|  |  | 
|  | /* | 
|  | * GL# USB-1: USB PHY Tx Control - force calibration to '8' | 
|  | * TXDATA_BLOCK_EN[21]=0x1, EXT_RCAL_EN[13]=0x1, IMP_CAL[6:3]=0x8 | 
|  | */ | 
|  | wrl(USB_PHY_TX_CTRL, (rdl(USB_PHY_TX_CTRL) & ~0x78) | 0x202040); | 
|  |  | 
|  | /* | 
|  | * GL# USB-3 GL# USB-9: USB PHY Rx Control | 
|  | * RXDATA_BLOCK_LENGHT[31:30]=0x3, EDGE_DET_SEL[27:26]=0, | 
|  | * CDR_FASTLOCK_EN[21]=0, DISCON_THRESHOLD[9:8]=0, SQ_THRESH[7:4]=0x1 | 
|  | */ | 
|  | wrl(USB_PHY_RX_CTRL, (rdl(USB_PHY_RX_CTRL) & ~0xc2003f0) | 0xc0000010); | 
|  |  | 
|  | /* | 
|  | * GL# USB-3 GL# USB-9: USB PHY IVREF Control | 
|  | * PLLVDD12[1:0]=0x2, RXVDD[5:4]=0x3, Reserved[19]=0 | 
|  | */ | 
|  | wrl(USB_PHY_IVREF_CTRL, (rdl(USB_PHY_IVREF_CTRL) & ~0x80003 ) | 0x32); | 
|  |  | 
|  | /* | 
|  | * GL# USB-3 GL# USB-9: USB PHY Test Group Control | 
|  | * REG_FIFO_SQ_RST[15]=0 | 
|  | */ | 
|  | wrl(USB_PHY_TST_GRP_CTRL, rdl(USB_PHY_TST_GRP_CTRL) & ~0x8000); | 
|  |  | 
|  | /* | 
|  | * Stop and reset controller | 
|  | */ | 
|  | wrl(USB_CMD, rdl(USB_CMD) & ~0x1); | 
|  | wrl(USB_CMD, rdl(USB_CMD) | 0x2); | 
|  | while (rdl(USB_CMD) & 0x2); | 
|  |  | 
|  | /* | 
|  | * GL# USB-5 Streaming disable REG_USB_MODE[4]=1 | 
|  | * TBD: This need to be done after each reset! | 
|  | * GL# USB-4 Setup USB Host mode | 
|  | */ | 
|  | wrl(USB_MODE, 0x13); | 
|  | } | 
|  |  | 
|  | static int ehci_orion_setup(struct usb_hcd *hcd) | 
|  | { | 
|  | struct ehci_hcd *ehci = hcd_to_ehci(hcd); | 
|  | int retval; | 
|  |  | 
|  | retval = ehci_halt(ehci); | 
|  | if (retval) | 
|  | return retval; | 
|  |  | 
|  | /* | 
|  | * data structure init | 
|  | */ | 
|  | retval = ehci_init(hcd); | 
|  | if (retval) | 
|  | return retval; | 
|  |  | 
|  | hcd->has_tt = 1; | 
|  |  | 
|  | ehci_reset(ehci); | 
|  | ehci_port_power(ehci, 0); | 
|  |  | 
|  | return retval; | 
|  | } | 
|  |  | 
|  | static const struct hc_driver ehci_orion_hc_driver = { | 
|  | .description = hcd_name, | 
|  | .product_desc = "Marvell Orion EHCI", | 
|  | .hcd_priv_size = sizeof(struct ehci_hcd), | 
|  |  | 
|  | /* | 
|  | * generic hardware linkage | 
|  | */ | 
|  | .irq = ehci_irq, | 
|  | .flags = HCD_MEMORY | HCD_USB2, | 
|  |  | 
|  | /* | 
|  | * basic lifecycle operations | 
|  | */ | 
|  | .reset = ehci_orion_setup, | 
|  | .start = ehci_run, | 
|  | .stop = ehci_stop, | 
|  | .shutdown = ehci_shutdown, | 
|  |  | 
|  | /* | 
|  | * managing i/o requests and associated device resources | 
|  | */ | 
|  | .urb_enqueue = ehci_urb_enqueue, | 
|  | .urb_dequeue = ehci_urb_dequeue, | 
|  | .endpoint_disable = ehci_endpoint_disable, | 
|  |  | 
|  | /* | 
|  | * scheduling support | 
|  | */ | 
|  | .get_frame_number = ehci_get_frame, | 
|  |  | 
|  | /* | 
|  | * root hub support | 
|  | */ | 
|  | .hub_status_data = ehci_hub_status_data, | 
|  | .hub_control = ehci_hub_control, | 
|  | .bus_suspend = ehci_bus_suspend, | 
|  | .bus_resume = ehci_bus_resume, | 
|  | .relinquish_port = ehci_relinquish_port, | 
|  | .port_handed_over = ehci_port_handed_over, | 
|  | }; | 
|  |  | 
|  | static void __init | 
|  | ehci_orion_conf_mbus_windows(struct usb_hcd *hcd, | 
|  | struct mbus_dram_target_info *dram) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i < 4; i++) { | 
|  | wrl(USB_WINDOW_CTRL(i), 0); | 
|  | wrl(USB_WINDOW_BASE(i), 0); | 
|  | } | 
|  |  | 
|  | for (i = 0; i < dram->num_cs; i++) { | 
|  | struct mbus_dram_window *cs = dram->cs + i; | 
|  |  | 
|  | wrl(USB_WINDOW_CTRL(i), ((cs->size - 1) & 0xffff0000) | | 
|  | (cs->mbus_attr << 8) | | 
|  | (dram->mbus_dram_target_id << 4) | 1); | 
|  | wrl(USB_WINDOW_BASE(i), cs->base); | 
|  | } | 
|  | } | 
|  |  | 
|  | static int __init ehci_orion_drv_probe(struct platform_device *pdev) | 
|  | { | 
|  | struct orion_ehci_data *pd = pdev->dev.platform_data; | 
|  | struct resource *res; | 
|  | struct usb_hcd *hcd; | 
|  | struct ehci_hcd *ehci; | 
|  | void __iomem *regs; | 
|  | int irq, err; | 
|  |  | 
|  | if (usb_disabled()) | 
|  | return -ENODEV; | 
|  |  | 
|  | pr_debug("Initializing Orion-SoC USB Host Controller\n"); | 
|  |  | 
|  | irq = platform_get_irq(pdev, 0); | 
|  | if (irq <= 0) { | 
|  | dev_err(&pdev->dev, | 
|  | "Found HC with no IRQ. Check %s setup!\n", | 
|  | dev_name(&pdev->dev)); | 
|  | err = -ENODEV; | 
|  | goto err1; | 
|  | } | 
|  |  | 
|  | res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | 
|  | if (!res) { | 
|  | dev_err(&pdev->dev, | 
|  | "Found HC with no register addr. Check %s setup!\n", | 
|  | dev_name(&pdev->dev)); | 
|  | err = -ENODEV; | 
|  | goto err1; | 
|  | } | 
|  |  | 
|  | if (!request_mem_region(res->start, res->end - res->start + 1, | 
|  | ehci_orion_hc_driver.description)) { | 
|  | dev_dbg(&pdev->dev, "controller already in use\n"); | 
|  | err = -EBUSY; | 
|  | goto err1; | 
|  | } | 
|  |  | 
|  | regs = ioremap(res->start, res->end - res->start + 1); | 
|  | if (regs == NULL) { | 
|  | dev_dbg(&pdev->dev, "error mapping memory\n"); | 
|  | err = -EFAULT; | 
|  | goto err2; | 
|  | } | 
|  |  | 
|  | hcd = usb_create_hcd(&ehci_orion_hc_driver, | 
|  | &pdev->dev, dev_name(&pdev->dev)); | 
|  | if (!hcd) { | 
|  | err = -ENOMEM; | 
|  | goto err3; | 
|  | } | 
|  |  | 
|  | hcd->rsrc_start = res->start; | 
|  | hcd->rsrc_len = res->end - res->start + 1; | 
|  | hcd->regs = regs; | 
|  |  | 
|  | ehci = hcd_to_ehci(hcd); | 
|  | ehci->caps = hcd->regs + 0x100; | 
|  | ehci->regs = hcd->regs + 0x100 + | 
|  | HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase)); | 
|  | ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params); | 
|  | hcd->has_tt = 1; | 
|  | ehci->sbrn = 0x20; | 
|  |  | 
|  | /* | 
|  | * (Re-)program MBUS remapping windows if we are asked to. | 
|  | */ | 
|  | if (pd != NULL && pd->dram != NULL) | 
|  | ehci_orion_conf_mbus_windows(hcd, pd->dram); | 
|  |  | 
|  | /* | 
|  | * setup Orion USB controller. | 
|  | */ | 
|  | switch (pd->phy_version) { | 
|  | case EHCI_PHY_NA:	/* dont change USB phy settings */ | 
|  | break; | 
|  | case EHCI_PHY_ORION: | 
|  | orion_usb_phy_v1_setup(hcd); | 
|  | break; | 
|  | case EHCI_PHY_DD: | 
|  | case EHCI_PHY_KW: | 
|  | default: | 
|  | printk(KERN_WARNING "Orion ehci -USB phy version isn't supported.\n"); | 
|  | } | 
|  |  | 
|  | err = usb_add_hcd(hcd, irq, IRQF_SHARED | IRQF_DISABLED); | 
|  | if (err) | 
|  | goto err4; | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | err4: | 
|  | usb_put_hcd(hcd); | 
|  | err3: | 
|  | iounmap(regs); | 
|  | err2: | 
|  | release_mem_region(res->start, res->end - res->start + 1); | 
|  | err1: | 
|  | dev_err(&pdev->dev, "init %s fail, %d\n", | 
|  | dev_name(&pdev->dev), err); | 
|  |  | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int __exit ehci_orion_drv_remove(struct platform_device *pdev) | 
|  | { | 
|  | struct usb_hcd *hcd = platform_get_drvdata(pdev); | 
|  |  | 
|  | usb_remove_hcd(hcd); | 
|  | iounmap(hcd->regs); | 
|  | release_mem_region(hcd->rsrc_start, hcd->rsrc_len); | 
|  | usb_put_hcd(hcd); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | MODULE_ALIAS("platform:orion-ehci"); | 
|  |  | 
|  | static struct platform_driver ehci_orion_driver = { | 
|  | .probe		= ehci_orion_drv_probe, | 
|  | .remove		= __exit_p(ehci_orion_drv_remove), | 
|  | .shutdown	= usb_hcd_platform_shutdown, | 
|  | .driver.name	= "orion-ehci", | 
|  | }; |