| /****************************************************************************** |
| * |
| * This file is provided under a dual BSD/GPLv2 license. When using or |
| * redistributing this file, you may do so under either license. |
| * |
| * GPL LICENSE SUMMARY |
| * |
| * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of version 2 of the GNU General Public License as |
| * published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
| * General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110, |
| * USA |
| * |
| * The full GNU General Public License is included in this distribution |
| * in the file called LICENSE.GPL. |
| * |
| * Contact Information: |
| * Intel Linux Wireless <ilw@linux.intel.com> |
| * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 |
| * |
| * BSD LICENSE |
| * |
| * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved. |
| * All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions |
| * are met: |
| * |
| * * Redistributions of source code must retain the above copyright |
| * notice, this list of conditions and the following disclaimer. |
| * * Redistributions in binary form must reproduce the above copyright |
| * notice, this list of conditions and the following disclaimer in |
| * the documentation and/or other materials provided with the |
| * distribution. |
| * * Neither the name Intel Corporation nor the names of its |
| * contributors may be used to endorse or promote products derived |
| * from this software without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS |
| * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT |
| * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR |
| * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT |
| * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, |
| * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT |
| * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, |
| * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY |
| * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
| * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
| * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| * |
| *****************************************************************************/ |
| /* |
| * Please use this file (iwl-4965-hw.h) only for hardware-related definitions. |
| * Use iwl-commands.h for uCode API definitions. |
| * Use iwl-dev.h for driver implementation definitions. |
| */ |
| |
| #ifndef __iwl_4965_hw_h__ |
| #define __iwl_4965_hw_h__ |
| |
| #include "iwl-fh.h" |
| |
| /* EEPROM */ |
| #define IWL4965_EEPROM_IMG_SIZE 1024 |
| |
| /* |
| * uCode queue management definitions ... |
| * The first queue used for block-ack aggregation is #7 (4965 only). |
| * All block-ack aggregation queues should map to Tx DMA/FIFO channel 7. |
| */ |
| #define IWL49_FIRST_AMPDU_QUEUE 7 |
| |
| /* Sizes and addresses for instruction and data memory (SRAM) in |
| * 4965's embedded processor. Driver access is via HBUS_TARG_MEM_* regs. */ |
| #define IWL49_RTC_INST_LOWER_BOUND (0x000000) |
| #define IWL49_RTC_INST_UPPER_BOUND (0x018000) |
| |
| #define IWL49_RTC_DATA_LOWER_BOUND (0x800000) |
| #define IWL49_RTC_DATA_UPPER_BOUND (0x80A000) |
| |
| #define IWL49_RTC_INST_SIZE (IWL49_RTC_INST_UPPER_BOUND - \ |
| IWL49_RTC_INST_LOWER_BOUND) |
| #define IWL49_RTC_DATA_SIZE (IWL49_RTC_DATA_UPPER_BOUND - \ |
| IWL49_RTC_DATA_LOWER_BOUND) |
| |
| #define IWL49_MAX_INST_SIZE IWL49_RTC_INST_SIZE |
| #define IWL49_MAX_DATA_SIZE IWL49_RTC_DATA_SIZE |
| |
| /* Size of uCode instruction memory in bootstrap state machine */ |
| #define IWL49_MAX_BSM_SIZE BSM_SRAM_SIZE |
| |
| static inline int iwl4965_hw_valid_rtc_data_addr(u32 addr) |
| { |
| return (addr >= IWL49_RTC_DATA_LOWER_BOUND) && |
| (addr < IWL49_RTC_DATA_UPPER_BOUND); |
| } |
| |
| /********************* START TEMPERATURE *************************************/ |
| |
| /** |
| * 4965 temperature calculation. |
| * |
| * The driver must calculate the device temperature before calculating |
| * a txpower setting (amplifier gain is temperature dependent). The |
| * calculation uses 4 measurements, 3 of which (R1, R2, R3) are calibration |
| * values used for the life of the driver, and one of which (R4) is the |
| * real-time temperature indicator. |
| * |
| * uCode provides all 4 values to the driver via the "initialize alive" |
| * notification (see struct iwl4965_init_alive_resp). After the runtime uCode |
| * image loads, uCode updates the R4 value via statistics notifications |
| * (see STATISTICS_NOTIFICATION), which occur after each received beacon |
| * when associated, or can be requested via REPLY_STATISTICS_CMD. |
| * |
| * NOTE: uCode provides the R4 value as a 23-bit signed value. Driver |
| * must sign-extend to 32 bits before applying formula below. |
| * |
| * Formula: |
| * |
| * degrees Kelvin = ((97 * 259 * (R4 - R2) / (R3 - R1)) / 100) + 8 |
| * |
| * NOTE: The basic formula is 259 * (R4-R2) / (R3-R1). The 97/100 is |
| * an additional correction, which should be centered around 0 degrees |
| * Celsius (273 degrees Kelvin). The 8 (3 percent of 273) compensates for |
| * centering the 97/100 correction around 0 degrees K. |
| * |
| * Add 273 to Kelvin value to find degrees Celsius, for comparing current |
| * temperature with factory-measured temperatures when calculating txpower |
| * settings. |
| */ |
| #define TEMPERATURE_CALIB_KELVIN_OFFSET 8 |
| #define TEMPERATURE_CALIB_A_VAL 259 |
| |
| /* Limit range of calculated temperature to be between these Kelvin values */ |
| #define IWL_TX_POWER_TEMPERATURE_MIN (263) |
| #define IWL_TX_POWER_TEMPERATURE_MAX (410) |
| |
| #define IWL_TX_POWER_TEMPERATURE_OUT_OF_RANGE(t) \ |
| (((t) < IWL_TX_POWER_TEMPERATURE_MIN) || \ |
| ((t) > IWL_TX_POWER_TEMPERATURE_MAX)) |
| |
| /********************* END TEMPERATURE ***************************************/ |
| |
| /********************* START TXPOWER *****************************************/ |
| |
| /** |
| * 4965 txpower calculations rely on information from three sources: |
| * |
| * 1) EEPROM |
| * 2) "initialize" alive notification |
| * 3) statistics notifications |
| * |
| * EEPROM data consists of: |
| * |
| * 1) Regulatory information (max txpower and channel usage flags) is provided |
| * separately for each channel that can possibly supported by 4965. |
| * 40 MHz wide (.11n HT40) channels are listed separately from 20 MHz |
| * (legacy) channels. |
| * |
| * See struct iwl4965_eeprom_channel for format, and struct iwl4965_eeprom |
| * for locations in EEPROM. |
| * |
| * 2) Factory txpower calibration information is provided separately for |
| * sub-bands of contiguous channels. 2.4GHz has just one sub-band, |
| * but 5 GHz has several sub-bands. |
| * |
| * In addition, per-band (2.4 and 5 Ghz) saturation txpowers are provided. |
| * |
| * See struct iwl4965_eeprom_calib_info (and the tree of structures |
| * contained within it) for format, and struct iwl4965_eeprom for |
| * locations in EEPROM. |
| * |
| * "Initialization alive" notification (see struct iwl4965_init_alive_resp) |
| * consists of: |
| * |
| * 1) Temperature calculation parameters. |
| * |
| * 2) Power supply voltage measurement. |
| * |
| * 3) Tx gain compensation to balance 2 transmitters for MIMO use. |
| * |
| * Statistics notifications deliver: |
| * |
| * 1) Current values for temperature param R4. |
| */ |
| |
| /** |
| * To calculate a txpower setting for a given desired target txpower, channel, |
| * modulation bit rate, and transmitter chain (4965 has 2 transmitters to |
| * support MIMO and transmit diversity), driver must do the following: |
| * |
| * 1) Compare desired txpower vs. (EEPROM) regulatory limit for this channel. |
| * Do not exceed regulatory limit; reduce target txpower if necessary. |
| * |
| * If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31), |
| * 2 transmitters will be used simultaneously; driver must reduce the |
| * regulatory limit by 3 dB (half-power) for each transmitter, so the |
| * combined total output of the 2 transmitters is within regulatory limits. |
| * |
| * |
| * 2) Compare target txpower vs. (EEPROM) saturation txpower *reduced by |
| * backoff for this bit rate*. Do not exceed (saturation - backoff[rate]); |
| * reduce target txpower if necessary. |
| * |
| * Backoff values below are in 1/2 dB units (equivalent to steps in |
| * txpower gain tables): |
| * |
| * OFDM 6 - 36 MBit: 10 steps (5 dB) |
| * OFDM 48 MBit: 15 steps (7.5 dB) |
| * OFDM 54 MBit: 17 steps (8.5 dB) |
| * OFDM 60 MBit: 20 steps (10 dB) |
| * CCK all rates: 10 steps (5 dB) |
| * |
| * Backoff values apply to saturation txpower on a per-transmitter basis; |
| * when using MIMO (2 transmitters), each transmitter uses the same |
| * saturation level provided in EEPROM, and the same backoff values; |
| * no reduction (such as with regulatory txpower limits) is required. |
| * |
| * Saturation and Backoff values apply equally to 20 Mhz (legacy) channel |
| * widths and 40 Mhz (.11n HT40) channel widths; there is no separate |
| * factory measurement for ht40 channels. |
| * |
| * The result of this step is the final target txpower. The rest of |
| * the steps figure out the proper settings for the device to achieve |
| * that target txpower. |
| * |
| * |
| * 3) Determine (EEPROM) calibration sub band for the target channel, by |
| * comparing against first and last channels in each sub band |
| * (see struct iwl4965_eeprom_calib_subband_info). |
| * |
| * |
| * 4) Linearly interpolate (EEPROM) factory calibration measurement sets, |
| * referencing the 2 factory-measured (sample) channels within the sub band. |
| * |
| * Interpolation is based on difference between target channel's frequency |
| * and the sample channels' frequencies. Since channel numbers are based |
| * on frequency (5 MHz between each channel number), this is equivalent |
| * to interpolating based on channel number differences. |
| * |
| * Note that the sample channels may or may not be the channels at the |
| * edges of the sub band. The target channel may be "outside" of the |
| * span of the sampled channels. |
| * |
| * Driver may choose the pair (for 2 Tx chains) of measurements (see |
| * struct iwl4965_eeprom_calib_ch_info) for which the actual measured |
| * txpower comes closest to the desired txpower. Usually, though, |
| * the middle set of measurements is closest to the regulatory limits, |
| * and is therefore a good choice for all txpower calculations (this |
| * assumes that high accuracy is needed for maximizing legal txpower, |
| * while lower txpower configurations do not need as much accuracy). |
| * |
| * Driver should interpolate both members of the chosen measurement pair, |
| * i.e. for both Tx chains (radio transmitters), unless the driver knows |
| * that only one of the chains will be used (e.g. only one tx antenna |
| * connected, but this should be unusual). The rate scaling algorithm |
| * switches antennas to find best performance, so both Tx chains will |
| * be used (although only one at a time) even for non-MIMO transmissions. |
| * |
| * Driver should interpolate factory values for temperature, gain table |
| * index, and actual power. The power amplifier detector values are |
| * not used by the driver. |
| * |
| * Sanity check: If the target channel happens to be one of the sample |
| * channels, the results should agree with the sample channel's |
| * measurements! |
| * |
| * |
| * 5) Find difference between desired txpower and (interpolated) |
| * factory-measured txpower. Using (interpolated) factory gain table index |
| * (shown elsewhere) as a starting point, adjust this index lower to |
| * increase txpower, or higher to decrease txpower, until the target |
| * txpower is reached. Each step in the gain table is 1/2 dB. |
| * |
| * For example, if factory measured txpower is 16 dBm, and target txpower |
| * is 13 dBm, add 6 steps to the factory gain index to reduce txpower |
| * by 3 dB. |
| * |
| * |
| * 6) Find difference between current device temperature and (interpolated) |
| * factory-measured temperature for sub-band. Factory values are in |
| * degrees Celsius. To calculate current temperature, see comments for |
| * "4965 temperature calculation". |
| * |
| * If current temperature is higher than factory temperature, driver must |
| * increase gain (lower gain table index), and vice verse. |
| * |
| * Temperature affects gain differently for different channels: |
| * |
| * 2.4 GHz all channels: 3.5 degrees per half-dB step |
| * 5 GHz channels 34-43: 4.5 degrees per half-dB step |
| * 5 GHz channels >= 44: 4.0 degrees per half-dB step |
| * |
| * NOTE: Temperature can increase rapidly when transmitting, especially |
| * with heavy traffic at high txpowers. Driver should update |
| * temperature calculations often under these conditions to |
| * maintain strong txpower in the face of rising temperature. |
| * |
| * |
| * 7) Find difference between current power supply voltage indicator |
| * (from "initialize alive") and factory-measured power supply voltage |
| * indicator (EEPROM). |
| * |
| * If the current voltage is higher (indicator is lower) than factory |
| * voltage, gain should be reduced (gain table index increased) by: |
| * |
| * (eeprom - current) / 7 |
| * |
| * If the current voltage is lower (indicator is higher) than factory |
| * voltage, gain should be increased (gain table index decreased) by: |
| * |
| * 2 * (current - eeprom) / 7 |
| * |
| * If number of index steps in either direction turns out to be > 2, |
| * something is wrong ... just use 0. |
| * |
| * NOTE: Voltage compensation is independent of band/channel. |
| * |
| * NOTE: "Initialize" uCode measures current voltage, which is assumed |
| * to be constant after this initial measurement. Voltage |
| * compensation for txpower (number of steps in gain table) |
| * may be calculated once and used until the next uCode bootload. |
| * |
| * |
| * 8) If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31), |
| * adjust txpower for each transmitter chain, so txpower is balanced |
| * between the two chains. There are 5 pairs of tx_atten[group][chain] |
| * values in "initialize alive", one pair for each of 5 channel ranges: |
| * |
| * Group 0: 5 GHz channel 34-43 |
| * Group 1: 5 GHz channel 44-70 |
| * Group 2: 5 GHz channel 71-124 |
| * Group 3: 5 GHz channel 125-200 |
| * Group 4: 2.4 GHz all channels |
| * |
| * Add the tx_atten[group][chain] value to the index for the target chain. |
| * The values are signed, but are in pairs of 0 and a non-negative number, |
| * so as to reduce gain (if necessary) of the "hotter" channel. This |
| * avoids any need to double-check for regulatory compliance after |
| * this step. |
| * |
| * |
| * 9) If setting up for a CCK rate, lower the gain by adding a CCK compensation |
| * value to the index: |
| * |
| * Hardware rev B: 9 steps (4.5 dB) |
| * Hardware rev C: 5 steps (2.5 dB) |
| * |
| * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG, |
| * bits [3:2], 1 = B, 2 = C. |
| * |
| * NOTE: This compensation is in addition to any saturation backoff that |
| * might have been applied in an earlier step. |
| * |
| * |
| * 10) Select the gain table, based on band (2.4 vs 5 GHz). |
| * |
| * Limit the adjusted index to stay within the table! |
| * |
| * |
| * 11) Read gain table entries for DSP and radio gain, place into appropriate |
| * location(s) in command (struct iwl4965_txpowertable_cmd). |
| */ |
| |
| /** |
| * When MIMO is used (2 transmitters operating simultaneously), driver should |
| * limit each transmitter to deliver a max of 3 dB below the regulatory limit |
| * for the device. That is, use half power for each transmitter, so total |
| * txpower is within regulatory limits. |
| * |
| * The value "6" represents number of steps in gain table to reduce power 3 dB. |
| * Each step is 1/2 dB. |
| */ |
| #define IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION (6) |
| |
| /** |
| * CCK gain compensation. |
| * |
| * When calculating txpowers for CCK, after making sure that the target power |
| * is within regulatory and saturation limits, driver must additionally |
| * back off gain by adding these values to the gain table index. |
| * |
| * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG, |
| * bits [3:2], 1 = B, 2 = C. |
| */ |
| #define IWL_TX_POWER_CCK_COMPENSATION_B_STEP (9) |
| #define IWL_TX_POWER_CCK_COMPENSATION_C_STEP (5) |
| |
| /* |
| * 4965 power supply voltage compensation for txpower |
| */ |
| #define TX_POWER_IWL_VOLTAGE_CODES_PER_03V (7) |
| |
| /** |
| * Gain tables. |
| * |
| * The following tables contain pair of values for setting txpower, i.e. |
| * gain settings for the output of the device's digital signal processor (DSP), |
| * and for the analog gain structure of the transmitter. |
| * |
| * Each entry in the gain tables represents a step of 1/2 dB. Note that these |
| * are *relative* steps, not indications of absolute output power. Output |
| * power varies with temperature, voltage, and channel frequency, and also |
| * requires consideration of average power (to satisfy regulatory constraints), |
| * and peak power (to avoid distortion of the output signal). |
| * |
| * Each entry contains two values: |
| * 1) DSP gain (or sometimes called DSP attenuation). This is a fine-grained |
| * linear value that multiplies the output of the digital signal processor, |
| * before being sent to the analog radio. |
| * 2) Radio gain. This sets the analog gain of the radio Tx path. |
| * It is a coarser setting, and behaves in a logarithmic (dB) fashion. |
| * |
| * EEPROM contains factory calibration data for txpower. This maps actual |
| * measured txpower levels to gain settings in the "well known" tables |
| * below ("well-known" means here that both factory calibration *and* the |
| * driver work with the same table). |
| * |
| * There are separate tables for 2.4 GHz and 5 GHz bands. The 5 GHz table |
| * has an extension (into negative indexes), in case the driver needs to |
| * boost power setting for high device temperatures (higher than would be |
| * present during factory calibration). A 5 Ghz EEPROM index of "40" |
| * corresponds to the 49th entry in the table used by the driver. |
| */ |
| #define MIN_TX_GAIN_INDEX (0) /* highest gain, lowest idx, 2.4 */ |
| #define MIN_TX_GAIN_INDEX_52GHZ_EXT (-9) /* highest gain, lowest idx, 5 */ |
| |
| /** |
| * 2.4 GHz gain table |
| * |
| * Index Dsp gain Radio gain |
| * 0 110 0x3f (highest gain) |
| * 1 104 0x3f |
| * 2 98 0x3f |
| * 3 110 0x3e |
| * 4 104 0x3e |
| * 5 98 0x3e |
| * 6 110 0x3d |
| * 7 104 0x3d |
| * 8 98 0x3d |
| * 9 110 0x3c |
| * 10 104 0x3c |
| * 11 98 0x3c |
| * 12 110 0x3b |
| * 13 104 0x3b |
| * 14 98 0x3b |
| * 15 110 0x3a |
| * 16 104 0x3a |
| * 17 98 0x3a |
| * 18 110 0x39 |
| * 19 104 0x39 |
| * 20 98 0x39 |
| * 21 110 0x38 |
| * 22 104 0x38 |
| * 23 98 0x38 |
| * 24 110 0x37 |
| * 25 104 0x37 |
| * 26 98 0x37 |
| * 27 110 0x36 |
| * 28 104 0x36 |
| * 29 98 0x36 |
| * 30 110 0x35 |
| * 31 104 0x35 |
| * 32 98 0x35 |
| * 33 110 0x34 |
| * 34 104 0x34 |
| * 35 98 0x34 |
| * 36 110 0x33 |
| * 37 104 0x33 |
| * 38 98 0x33 |
| * 39 110 0x32 |
| * 40 104 0x32 |
| * 41 98 0x32 |
| * 42 110 0x31 |
| * 43 104 0x31 |
| * 44 98 0x31 |
| * 45 110 0x30 |
| * 46 104 0x30 |
| * 47 98 0x30 |
| * 48 110 0x6 |
| * 49 104 0x6 |
| * 50 98 0x6 |
| * 51 110 0x5 |
| * 52 104 0x5 |
| * 53 98 0x5 |
| * 54 110 0x4 |
| * 55 104 0x4 |
| * 56 98 0x4 |
| * 57 110 0x3 |
| * 58 104 0x3 |
| * 59 98 0x3 |
| * 60 110 0x2 |
| * 61 104 0x2 |
| * 62 98 0x2 |
| * 63 110 0x1 |
| * 64 104 0x1 |
| * 65 98 0x1 |
| * 66 110 0x0 |
| * 67 104 0x0 |
| * 68 98 0x0 |
| * 69 97 0 |
| * 70 96 0 |
| * 71 95 0 |
| * 72 94 0 |
| * 73 93 0 |
| * 74 92 0 |
| * 75 91 0 |
| * 76 90 0 |
| * 77 89 0 |
| * 78 88 0 |
| * 79 87 0 |
| * 80 86 0 |
| * 81 85 0 |
| * 82 84 0 |
| * 83 83 0 |
| * 84 82 0 |
| * 85 81 0 |
| * 86 80 0 |
| * 87 79 0 |
| * 88 78 0 |
| * 89 77 0 |
| * 90 76 0 |
| * 91 75 0 |
| * 92 74 0 |
| * 93 73 0 |
| * 94 72 0 |
| * 95 71 0 |
| * 96 70 0 |
| * 97 69 0 |
| * 98 68 0 |
| */ |
| |
| /** |
| * 5 GHz gain table |
| * |
| * Index Dsp gain Radio gain |
| * -9 123 0x3F (highest gain) |
| * -8 117 0x3F |
| * -7 110 0x3F |
| * -6 104 0x3F |
| * -5 98 0x3F |
| * -4 110 0x3E |
| * -3 104 0x3E |
| * -2 98 0x3E |
| * -1 110 0x3D |
| * 0 104 0x3D |
| * 1 98 0x3D |
| * 2 110 0x3C |
| * 3 104 0x3C |
| * 4 98 0x3C |
| * 5 110 0x3B |
| * 6 104 0x3B |
| * 7 98 0x3B |
| * 8 110 0x3A |
| * 9 104 0x3A |
| * 10 98 0x3A |
| * 11 110 0x39 |
| * 12 104 0x39 |
| * 13 98 0x39 |
| * 14 110 0x38 |
| * 15 104 0x38 |
| * 16 98 0x38 |
| * 17 110 0x37 |
| * 18 104 0x37 |
| * 19 98 0x37 |
| * 20 110 0x36 |
| * 21 104 0x36 |
| * 22 98 0x36 |
| * 23 110 0x35 |
| * 24 104 0x35 |
| * 25 98 0x35 |
| * 26 110 0x34 |
| * 27 104 0x34 |
| * 28 98 0x34 |
| * 29 110 0x33 |
| * 30 104 0x33 |
| * 31 98 0x33 |
| * 32 110 0x32 |
| * 33 104 0x32 |
| * 34 98 0x32 |
| * 35 110 0x31 |
| * 36 104 0x31 |
| * 37 98 0x31 |
| * 38 110 0x30 |
| * 39 104 0x30 |
| * 40 98 0x30 |
| * 41 110 0x25 |
| * 42 104 0x25 |
| * 43 98 0x25 |
| * 44 110 0x24 |
| * 45 104 0x24 |
| * 46 98 0x24 |
| * 47 110 0x23 |
| * 48 104 0x23 |
| * 49 98 0x23 |
| * 50 110 0x22 |
| * 51 104 0x18 |
| * 52 98 0x18 |
| * 53 110 0x17 |
| * 54 104 0x17 |
| * 55 98 0x17 |
| * 56 110 0x16 |
| * 57 104 0x16 |
| * 58 98 0x16 |
| * 59 110 0x15 |
| * 60 104 0x15 |
| * 61 98 0x15 |
| * 62 110 0x14 |
| * 63 104 0x14 |
| * 64 98 0x14 |
| * 65 110 0x13 |
| * 66 104 0x13 |
| * 67 98 0x13 |
| * 68 110 0x12 |
| * 69 104 0x08 |
| * 70 98 0x08 |
| * 71 110 0x07 |
| * 72 104 0x07 |
| * 73 98 0x07 |
| * 74 110 0x06 |
| * 75 104 0x06 |
| * 76 98 0x06 |
| * 77 110 0x05 |
| * 78 104 0x05 |
| * 79 98 0x05 |
| * 80 110 0x04 |
| * 81 104 0x04 |
| * 82 98 0x04 |
| * 83 110 0x03 |
| * 84 104 0x03 |
| * 85 98 0x03 |
| * 86 110 0x02 |
| * 87 104 0x02 |
| * 88 98 0x02 |
| * 89 110 0x01 |
| * 90 104 0x01 |
| * 91 98 0x01 |
| * 92 110 0x00 |
| * 93 104 0x00 |
| * 94 98 0x00 |
| * 95 93 0x00 |
| * 96 88 0x00 |
| * 97 83 0x00 |
| * 98 78 0x00 |
| */ |
| |
| |
| /** |
| * Sanity checks and default values for EEPROM regulatory levels. |
| * If EEPROM values fall outside MIN/MAX range, use default values. |
| * |
| * Regulatory limits refer to the maximum average txpower allowed by |
| * regulatory agencies in the geographies in which the device is meant |
| * to be operated. These limits are SKU-specific (i.e. geography-specific), |
| * and channel-specific; each channel has an individual regulatory limit |
| * listed in the EEPROM. |
| * |
| * Units are in half-dBm (i.e. "34" means 17 dBm). |
| */ |
| #define IWL_TX_POWER_DEFAULT_REGULATORY_24 (34) |
| #define IWL_TX_POWER_DEFAULT_REGULATORY_52 (34) |
| #define IWL_TX_POWER_REGULATORY_MIN (0) |
| #define IWL_TX_POWER_REGULATORY_MAX (34) |
| |
| /** |
| * Sanity checks and default values for EEPROM saturation levels. |
| * If EEPROM values fall outside MIN/MAX range, use default values. |
| * |
| * Saturation is the highest level that the output power amplifier can produce |
| * without significant clipping distortion. This is a "peak" power level. |
| * Different types of modulation (i.e. various "rates", and OFDM vs. CCK) |
| * require differing amounts of backoff, relative to their average power output, |
| * in order to avoid clipping distortion. |
| * |
| * Driver must make sure that it is violating neither the saturation limit, |
| * nor the regulatory limit, when calculating Tx power settings for various |
| * rates. |
| * |
| * Units are in half-dBm (i.e. "38" means 19 dBm). |
| */ |
| #define IWL_TX_POWER_DEFAULT_SATURATION_24 (38) |
| #define IWL_TX_POWER_DEFAULT_SATURATION_52 (38) |
| #define IWL_TX_POWER_SATURATION_MIN (20) |
| #define IWL_TX_POWER_SATURATION_MAX (50) |
| |
| /** |
| * Channel groups used for Tx Attenuation calibration (MIMO tx channel balance) |
| * and thermal Txpower calibration. |
| * |
| * When calculating txpower, driver must compensate for current device |
| * temperature; higher temperature requires higher gain. Driver must calculate |
| * current temperature (see "4965 temperature calculation"), then compare vs. |
| * factory calibration temperature in EEPROM; if current temperature is higher |
| * than factory temperature, driver must *increase* gain by proportions shown |
| * in table below. If current temperature is lower than factory, driver must |
| * *decrease* gain. |
| * |
| * Different frequency ranges require different compensation, as shown below. |
| */ |
| /* Group 0, 5.2 GHz ch 34-43: 4.5 degrees per 1/2 dB. */ |
| #define CALIB_IWL_TX_ATTEN_GR1_FCH 34 |
| #define CALIB_IWL_TX_ATTEN_GR1_LCH 43 |
| |
| /* Group 1, 5.3 GHz ch 44-70: 4.0 degrees per 1/2 dB. */ |
| #define CALIB_IWL_TX_ATTEN_GR2_FCH 44 |
| #define CALIB_IWL_TX_ATTEN_GR2_LCH 70 |
| |
| /* Group 2, 5.5 GHz ch 71-124: 4.0 degrees per 1/2 dB. */ |
| #define CALIB_IWL_TX_ATTEN_GR3_FCH 71 |
| #define CALIB_IWL_TX_ATTEN_GR3_LCH 124 |
| |
| /* Group 3, 5.7 GHz ch 125-200: 4.0 degrees per 1/2 dB. */ |
| #define CALIB_IWL_TX_ATTEN_GR4_FCH 125 |
| #define CALIB_IWL_TX_ATTEN_GR4_LCH 200 |
| |
| /* Group 4, 2.4 GHz all channels: 3.5 degrees per 1/2 dB. */ |
| #define CALIB_IWL_TX_ATTEN_GR5_FCH 1 |
| #define CALIB_IWL_TX_ATTEN_GR5_LCH 20 |
| |
| enum { |
| CALIB_CH_GROUP_1 = 0, |
| CALIB_CH_GROUP_2 = 1, |
| CALIB_CH_GROUP_3 = 2, |
| CALIB_CH_GROUP_4 = 3, |
| CALIB_CH_GROUP_5 = 4, |
| CALIB_CH_GROUP_MAX |
| }; |
| |
| /********************* END TXPOWER *****************************************/ |
| |
| |
| /** |
| * Tx/Rx Queues |
| * |
| * Most communication between driver and 4965 is via queues of data buffers. |
| * For example, all commands that the driver issues to device's embedded |
| * controller (uCode) are via the command queue (one of the Tx queues). All |
| * uCode command responses/replies/notifications, including Rx frames, are |
| * conveyed from uCode to driver via the Rx queue. |
| * |
| * Most support for these queues, including handshake support, resides in |
| * structures in host DRAM, shared between the driver and the device. When |
| * allocating this memory, the driver must make sure that data written by |
| * the host CPU updates DRAM immediately (and does not get "stuck" in CPU's |
| * cache memory), so DRAM and cache are consistent, and the device can |
| * immediately see changes made by the driver. |
| * |
| * 4965 supports up to 16 DRAM-based Tx queues, and services these queues via |
| * up to 7 DMA channels (FIFOs). Each Tx queue is supported by a circular array |
| * in DRAM containing 256 Transmit Frame Descriptors (TFDs). |
| */ |
| #define IWL49_NUM_FIFOS 7 |
| #define IWL49_CMD_FIFO_NUM 4 |
| #define IWL49_NUM_QUEUES 16 |
| #define IWL49_NUM_AMPDU_QUEUES 8 |
| |
| |
| /** |
| * struct iwl4965_schedq_bc_tbl |
| * |
| * Byte Count table |
| * |
| * Each Tx queue uses a byte-count table containing 320 entries: |
| * one 16-bit entry for each of 256 TFDs, plus an additional 64 entries that |
| * duplicate the first 64 entries (to avoid wrap-around within a Tx window; |
| * max Tx window is 64 TFDs). |
| * |
| * When driver sets up a new TFD, it must also enter the total byte count |
| * of the frame to be transmitted into the corresponding entry in the byte |
| * count table for the chosen Tx queue. If the TFD index is 0-63, the driver |
| * must duplicate the byte count entry in corresponding index 256-319. |
| * |
| * padding puts each byte count table on a 1024-byte boundary; |
| * 4965 assumes tables are separated by 1024 bytes. |
| */ |
| struct iwl4965_scd_bc_tbl { |
| __le16 tfd_offset[TFD_QUEUE_BC_SIZE]; |
| u8 pad[1024 - (TFD_QUEUE_BC_SIZE) * sizeof(__le16)]; |
| } __packed; |
| |
| |
| #define IWL4965_RTC_INST_LOWER_BOUND (0x000000) |
| |
| /* RSSI to dBm */ |
| #define IWL4965_RSSI_OFFSET 44 |
| |
| /* PCI registers */ |
| #define PCI_CFG_RETRY_TIMEOUT 0x041 |
| |
| /* PCI register values */ |
| #define PCI_CFG_LINK_CTRL_VAL_L0S_EN 0x01 |
| #define PCI_CFG_LINK_CTRL_VAL_L1_EN 0x02 |
| |
| #define IWL4965_DEFAULT_TX_RETRY 15 |
| |
| /* EEPROM */ |
| #define IWL4965_FIRST_AMPDU_QUEUE 10 |
| |
| |
| #endif /* !__iwl_4965_hw_h__ */ |