|  | /* lasi_82596.c -- driver for the intel 82596 ethernet controller, as | 
|  | munged into HPPA boxen . | 
|  |  | 
|  | This driver is based upon 82596.c, original credits are below... | 
|  | but there were too many hoops which HP wants jumped through to | 
|  | keep this code in there in a sane manner. | 
|  |  | 
|  | 3 primary sources of the mess -- | 
|  | 1) hppa needs *lots* of cacheline flushing to keep this kind of | 
|  | MMIO running. | 
|  |  | 
|  | 2) The 82596 needs to see all of its pointers as their physical | 
|  | address.  Thus virt_to_bus/bus_to_virt are *everywhere*. | 
|  |  | 
|  | 3) The implementation HP is using seems to be significantly pickier | 
|  | about when and how the command and RX units are started.  some | 
|  | command ordering was changed. | 
|  |  | 
|  | Examination of the mach driver leads one to believe that there | 
|  | might be a saner way to pull this off...  anyone who feels like a | 
|  | full rewrite can be my guest. | 
|  |  | 
|  | Split 02/13/2000 Sam Creasey (sammy@oh.verio.com) | 
|  |  | 
|  | 02/01/2000  Initial modifications for parisc by Helge Deller (deller@gmx.de) | 
|  | 03/02/2000  changes for better/correct(?) cache-flushing (deller) | 
|  | */ | 
|  |  | 
|  | /* 82596.c: A generic 82596 ethernet driver for linux. */ | 
|  | /* | 
|  | Based on Apricot.c | 
|  | Written 1994 by Mark Evans. | 
|  | This driver is for the Apricot 82596 bus-master interface | 
|  |  | 
|  | Modularised 12/94 Mark Evans | 
|  |  | 
|  |  | 
|  | Modified to support the 82596 ethernet chips on 680x0 VME boards. | 
|  | by Richard Hirst <richard@sleepie.demon.co.uk> | 
|  | Renamed to be 82596.c | 
|  |  | 
|  | 980825:  Changed to receive directly in to sk_buffs which are | 
|  | allocated at open() time.  Eliminates copy on incoming frames | 
|  | (small ones are still copied).  Shared data now held in a | 
|  | non-cached page, so we can run on 68060 in copyback mode. | 
|  |  | 
|  | TBD: | 
|  | * look at deferring rx frames rather than discarding (as per tulip) | 
|  | * handle tx ring full as per tulip | 
|  | * performace test to tune rx_copybreak | 
|  |  | 
|  | Most of my modifications relate to the braindead big-endian | 
|  | implementation by Intel.  When the i596 is operating in | 
|  | 'big-endian' mode, it thinks a 32 bit value of 0x12345678 | 
|  | should be stored as 0x56781234.  This is a real pain, when | 
|  | you have linked lists which are shared by the 680x0 and the | 
|  | i596. | 
|  |  | 
|  | Driver skeleton | 
|  | Written 1993 by Donald Becker. | 
|  | Copyright 1993 United States Government as represented by the Director, | 
|  | National Security Agency. This software may only be used and distributed | 
|  | according to the terms of the GNU General Public License as modified by SRC, | 
|  | incorporated herein by reference. | 
|  |  | 
|  | The author may be reached as becker@scyld.com, or C/O | 
|  | Scyld Computing Corporation, 410 Severn Ave., Suite 210, Annapolis MD 21403 | 
|  |  | 
|  | */ | 
|  |  | 
|  | #include <linux/module.h> | 
|  | #include <linux/kernel.h> | 
|  | #include <linux/string.h> | 
|  | #include <linux/ptrace.h> | 
|  | #include <linux/errno.h> | 
|  | #include <linux/ioport.h> | 
|  | #include <linux/slab.h> | 
|  | #include <linux/interrupt.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/netdevice.h> | 
|  | #include <linux/etherdevice.h> | 
|  | #include <linux/skbuff.h> | 
|  | #include <linux/init.h> | 
|  | #include <linux/pci.h> | 
|  | #include <linux/types.h> | 
|  | #include <linux/bitops.h> | 
|  |  | 
|  | #include <asm/io.h> | 
|  | #include <asm/pgtable.h> | 
|  | #include <asm/irq.h> | 
|  | #include <asm/pdc.h> | 
|  | #include <asm/cache.h> | 
|  | #include <asm/parisc-device.h> | 
|  |  | 
|  | #define LASI_82596_DRIVER_VERSION "LASI 82596 driver - Revision: 1.30" | 
|  |  | 
|  | /* DEBUG flags | 
|  | */ | 
|  |  | 
|  | #define DEB_INIT	0x0001 | 
|  | #define DEB_PROBE	0x0002 | 
|  | #define DEB_SERIOUS	0x0004 | 
|  | #define DEB_ERRORS	0x0008 | 
|  | #define DEB_MULTI	0x0010 | 
|  | #define DEB_TDR		0x0020 | 
|  | #define DEB_OPEN	0x0040 | 
|  | #define DEB_RESET	0x0080 | 
|  | #define DEB_ADDCMD	0x0100 | 
|  | #define DEB_STATUS	0x0200 | 
|  | #define DEB_STARTTX	0x0400 | 
|  | #define DEB_RXADDR	0x0800 | 
|  | #define DEB_TXADDR	0x1000 | 
|  | #define DEB_RXFRAME	0x2000 | 
|  | #define DEB_INTS	0x4000 | 
|  | #define DEB_STRUCT	0x8000 | 
|  | #define DEB_ANY		0xffff | 
|  |  | 
|  |  | 
|  | #define DEB(x,y)	if (i596_debug & (x)) { y; } | 
|  |  | 
|  |  | 
|  | #define  CHECK_WBACK(addr,len) \ | 
|  | do { dma_cache_sync((void *)addr, len, DMA_TO_DEVICE); } while (0) | 
|  |  | 
|  | #define  CHECK_INV(addr,len) \ | 
|  | do { dma_cache_sync((void *)addr, len, DMA_FROM_DEVICE); } while(0) | 
|  |  | 
|  | #define  CHECK_WBACK_INV(addr,len) \ | 
|  | do { dma_cache_sync((void *)addr, len, DMA_BIDIRECTIONAL); } while (0) | 
|  |  | 
|  |  | 
|  | #define PA_I82596_RESET		0	/* Offsets relative to LASI-LAN-Addr.*/ | 
|  | #define PA_CPU_PORT_L_ACCESS	4 | 
|  | #define PA_CHANNEL_ATTENTION	8 | 
|  |  | 
|  |  | 
|  | /* | 
|  | * Define various macros for Channel Attention, word swapping etc., dependent | 
|  | * on architecture.  MVME and BVME are 680x0 based, otherwise it is Intel. | 
|  | */ | 
|  |  | 
|  | #ifdef __BIG_ENDIAN | 
|  | #define WSWAPrfd(x)  (((u32)(x)<<16) | ((((u32)(x)))>>16)) | 
|  | #define WSWAPrbd(x)  (((u32)(x)<<16) | ((((u32)(x)))>>16)) | 
|  | #define WSWAPiscp(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) | 
|  | #define WSWAPscb(x)  (((u32)(x)<<16) | ((((u32)(x)))>>16)) | 
|  | #define WSWAPcmd(x)  (((u32)(x)<<16) | ((((u32)(x)))>>16)) | 
|  | #define WSWAPtbd(x)  (((u32)(x)<<16) | ((((u32)(x)))>>16)) | 
|  | #define WSWAPchar(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) | 
|  | #define ISCP_BUSY	0x00010000 | 
|  | #define MACH_IS_APRICOT	0 | 
|  | #else | 
|  | #define WSWAPrfd(x)     ((struct i596_rfd *)(x)) | 
|  | #define WSWAPrbd(x)     ((struct i596_rbd *)(x)) | 
|  | #define WSWAPiscp(x)    ((struct i596_iscp *)(x)) | 
|  | #define WSWAPscb(x)     ((struct i596_scb *)(x)) | 
|  | #define WSWAPcmd(x)     ((struct i596_cmd *)(x)) | 
|  | #define WSWAPtbd(x)     ((struct i596_tbd *)(x)) | 
|  | #define WSWAPchar(x)    ((char *)(x)) | 
|  | #define ISCP_BUSY	0x0001 | 
|  | #define MACH_IS_APRICOT	1 | 
|  | #endif | 
|  |  | 
|  | /* | 
|  | * The MPU_PORT command allows direct access to the 82596. With PORT access | 
|  | * the following commands are available (p5-18). The 32-bit port command | 
|  | * must be word-swapped with the most significant word written first. | 
|  | * This only applies to VME boards. | 
|  | */ | 
|  | #define PORT_RESET		0x00	/* reset 82596 */ | 
|  | #define PORT_SELFTEST		0x01	/* selftest */ | 
|  | #define PORT_ALTSCP		0x02	/* alternate SCB address */ | 
|  | #define PORT_ALTDUMP		0x03	/* Alternate DUMP address */ | 
|  |  | 
|  | static int i596_debug = (DEB_SERIOUS|DEB_PROBE); | 
|  |  | 
|  | MODULE_AUTHOR("Richard Hirst"); | 
|  | MODULE_DESCRIPTION("i82596 driver"); | 
|  | MODULE_LICENSE("GPL"); | 
|  | MODULE_PARM(i596_debug, "i"); | 
|  | MODULE_PARM_DESC(i596_debug, "lasi_82596 debug mask"); | 
|  |  | 
|  | /* Copy frames shorter than rx_copybreak, otherwise pass on up in | 
|  | * a full sized sk_buff.  Value of 100 stolen from tulip.c (!alpha). | 
|  | */ | 
|  | static int rx_copybreak = 100; | 
|  |  | 
|  | #define MAX_DRIVERS	4	/* max count of drivers */ | 
|  |  | 
|  | #define PKT_BUF_SZ	1536 | 
|  | #define MAX_MC_CNT	64 | 
|  |  | 
|  | #define I596_NULL ((u32)0xffffffff) | 
|  |  | 
|  | #define CMD_EOL		0x8000	/* The last command of the list, stop. */ | 
|  | #define CMD_SUSP	0x4000	/* Suspend after doing cmd. */ | 
|  | #define CMD_INTR	0x2000	/* Interrupt after doing cmd. */ | 
|  |  | 
|  | #define CMD_FLEX	0x0008	/* Enable flexible memory model */ | 
|  |  | 
|  | enum commands { | 
|  | CmdNOp = 0, CmdSASetup = 1, CmdConfigure = 2, CmdMulticastList = 3, | 
|  | CmdTx = 4, CmdTDR = 5, CmdDump = 6, CmdDiagnose = 7 | 
|  | }; | 
|  |  | 
|  | #define STAT_C		0x8000	/* Set to 0 after execution */ | 
|  | #define STAT_B		0x4000	/* Command being executed */ | 
|  | #define STAT_OK		0x2000	/* Command executed ok */ | 
|  | #define STAT_A		0x1000	/* Command aborted */ | 
|  |  | 
|  | #define	 CUC_START	0x0100 | 
|  | #define	 CUC_RESUME	0x0200 | 
|  | #define	 CUC_SUSPEND    0x0300 | 
|  | #define	 CUC_ABORT	0x0400 | 
|  | #define	 RX_START	0x0010 | 
|  | #define	 RX_RESUME	0x0020 | 
|  | #define	 RX_SUSPEND	0x0030 | 
|  | #define	 RX_ABORT	0x0040 | 
|  |  | 
|  | #define TX_TIMEOUT	5 | 
|  |  | 
|  | #define OPT_SWAP_PORT	0x0001	/* Need to wordswp on the MPU port */ | 
|  |  | 
|  |  | 
|  | struct i596_reg { | 
|  | unsigned short porthi; | 
|  | unsigned short portlo; | 
|  | u32            ca; | 
|  | }; | 
|  |  | 
|  | #define EOF		0x8000 | 
|  | #define SIZE_MASK	0x3fff | 
|  |  | 
|  | struct i596_tbd { | 
|  | unsigned short size; | 
|  | unsigned short pad; | 
|  | dma_addr_t     next; | 
|  | dma_addr_t     data; | 
|  | u32 cache_pad[5];		/* Total 32 bytes... */ | 
|  | }; | 
|  |  | 
|  | /* The command structure has two 'next' pointers; v_next is the address of | 
|  | * the next command as seen by the CPU, b_next is the address of the next | 
|  | * command as seen by the 82596.  The b_next pointer, as used by the 82596 | 
|  | * always references the status field of the next command, rather than the | 
|  | * v_next field, because the 82596 is unaware of v_next.  It may seem more | 
|  | * logical to put v_next at the end of the structure, but we cannot do that | 
|  | * because the 82596 expects other fields to be there, depending on command | 
|  | * type. | 
|  | */ | 
|  |  | 
|  | struct i596_cmd { | 
|  | struct i596_cmd *v_next;	/* Address from CPUs viewpoint */ | 
|  | unsigned short status; | 
|  | unsigned short command; | 
|  | dma_addr_t     b_next;	/* Address from i596 viewpoint */ | 
|  | }; | 
|  |  | 
|  | struct tx_cmd { | 
|  | struct i596_cmd cmd; | 
|  | dma_addr_t     tbd; | 
|  | unsigned short size; | 
|  | unsigned short pad; | 
|  | struct sk_buff *skb;		/* So we can free it after tx */ | 
|  | dma_addr_t dma_addr; | 
|  | #ifdef __LP64__ | 
|  | u32 cache_pad[6];		/* Total 64 bytes... */ | 
|  | #else | 
|  | u32 cache_pad[1];		/* Total 32 bytes... */ | 
|  | #endif | 
|  | }; | 
|  |  | 
|  | struct tdr_cmd { | 
|  | struct i596_cmd cmd; | 
|  | unsigned short status; | 
|  | unsigned short pad; | 
|  | }; | 
|  |  | 
|  | struct mc_cmd { | 
|  | struct i596_cmd cmd; | 
|  | short mc_cnt; | 
|  | char mc_addrs[MAX_MC_CNT*6]; | 
|  | }; | 
|  |  | 
|  | struct sa_cmd { | 
|  | struct i596_cmd cmd; | 
|  | char eth_addr[8]; | 
|  | }; | 
|  |  | 
|  | struct cf_cmd { | 
|  | struct i596_cmd cmd; | 
|  | char i596_config[16]; | 
|  | }; | 
|  |  | 
|  | struct i596_rfd { | 
|  | unsigned short stat; | 
|  | unsigned short cmd; | 
|  | dma_addr_t     b_next;	/* Address from i596 viewpoint */ | 
|  | dma_addr_t     rbd; | 
|  | unsigned short count; | 
|  | unsigned short size; | 
|  | struct i596_rfd *v_next;	/* Address from CPUs viewpoint */ | 
|  | struct i596_rfd *v_prev; | 
|  | #ifndef __LP64__ | 
|  | u32 cache_pad[2];		/* Total 32 bytes... */ | 
|  | #endif | 
|  | }; | 
|  |  | 
|  | struct i596_rbd { | 
|  | /* hardware data */ | 
|  | unsigned short count; | 
|  | unsigned short zero1; | 
|  | dma_addr_t     b_next; | 
|  | dma_addr_t     b_data;		/* Address from i596 viewpoint */ | 
|  | unsigned short size; | 
|  | unsigned short zero2; | 
|  | /* driver data */ | 
|  | struct sk_buff *skb; | 
|  | struct i596_rbd *v_next; | 
|  | dma_addr_t     b_addr;		/* This rbd addr from i596 view */ | 
|  | unsigned char *v_data;		/* Address from CPUs viewpoint */ | 
|  | /* Total 32 bytes... */ | 
|  | #ifdef __LP64__ | 
|  | u32 cache_pad[4]; | 
|  | #endif | 
|  | }; | 
|  |  | 
|  | /* These values as chosen so struct i596_private fits in one page... */ | 
|  |  | 
|  | #define TX_RING_SIZE 32 | 
|  | #define RX_RING_SIZE 16 | 
|  |  | 
|  | struct i596_scb { | 
|  | unsigned short status; | 
|  | unsigned short command; | 
|  | dma_addr_t    cmd; | 
|  | dma_addr_t    rfd; | 
|  | u32           crc_err; | 
|  | u32           align_err; | 
|  | u32           resource_err; | 
|  | u32           over_err; | 
|  | u32           rcvdt_err; | 
|  | u32           short_err; | 
|  | unsigned short t_on; | 
|  | unsigned short t_off; | 
|  | }; | 
|  |  | 
|  | struct i596_iscp { | 
|  | u32           stat; | 
|  | dma_addr_t    scb; | 
|  | }; | 
|  |  | 
|  | struct i596_scp { | 
|  | u32           sysbus; | 
|  | u32            pad; | 
|  | dma_addr_t    iscp; | 
|  | }; | 
|  |  | 
|  | struct i596_private { | 
|  | volatile struct i596_scp scp		__attribute__((aligned(32))); | 
|  | volatile struct i596_iscp iscp		__attribute__((aligned(32))); | 
|  | volatile struct i596_scb scb		__attribute__((aligned(32))); | 
|  | struct sa_cmd sa_cmd			__attribute__((aligned(32))); | 
|  | struct cf_cmd cf_cmd			__attribute__((aligned(32))); | 
|  | struct tdr_cmd tdr_cmd			__attribute__((aligned(32))); | 
|  | struct mc_cmd mc_cmd			__attribute__((aligned(32))); | 
|  | struct i596_rfd rfds[RX_RING_SIZE]	__attribute__((aligned(32))); | 
|  | struct i596_rbd rbds[RX_RING_SIZE]	__attribute__((aligned(32))); | 
|  | struct tx_cmd tx_cmds[TX_RING_SIZE]	__attribute__((aligned(32))); | 
|  | struct i596_tbd tbds[TX_RING_SIZE]	__attribute__((aligned(32))); | 
|  | u32    stat; | 
|  | int last_restart; | 
|  | struct i596_rfd *rfd_head; | 
|  | struct i596_rbd *rbd_head; | 
|  | struct i596_cmd *cmd_tail; | 
|  | struct i596_cmd *cmd_head; | 
|  | int cmd_backlog; | 
|  | u32    last_cmd; | 
|  | struct net_device_stats stats; | 
|  | int next_tx_cmd; | 
|  | int options; | 
|  | spinlock_t lock; | 
|  | dma_addr_t dma_addr; | 
|  | struct device *dev; | 
|  | }; | 
|  |  | 
|  | static char init_setup[] = | 
|  | { | 
|  | 0x8E,			/* length, prefetch on */ | 
|  | 0xC8,			/* fifo to 8, monitor off */ | 
|  | 0x80,			/* don't save bad frames */ | 
|  | 0x2E,			/* No source address insertion, 8 byte preamble */ | 
|  | 0x00,			/* priority and backoff defaults */ | 
|  | 0x60,			/* interframe spacing */ | 
|  | 0x00,			/* slot time LSB */ | 
|  | 0xf2,			/* slot time and retries */ | 
|  | 0x00,			/* promiscuous mode */ | 
|  | 0x00,			/* collision detect */ | 
|  | 0x40,			/* minimum frame length */ | 
|  | 0xff, | 
|  | 0x00, | 
|  | 0x7f /*  *multi IA */ }; | 
|  |  | 
|  | static int i596_open(struct net_device *dev); | 
|  | static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev); | 
|  | static irqreturn_t i596_interrupt(int irq, void *dev_id, struct pt_regs *regs); | 
|  | static int i596_close(struct net_device *dev); | 
|  | static struct net_device_stats *i596_get_stats(struct net_device *dev); | 
|  | static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd); | 
|  | static void i596_tx_timeout (struct net_device *dev); | 
|  | static void print_eth(unsigned char *buf, char *str); | 
|  | static void set_multicast_list(struct net_device *dev); | 
|  |  | 
|  | static int rx_ring_size = RX_RING_SIZE; | 
|  | static int ticks_limit = 100; | 
|  | static int max_cmd_backlog = TX_RING_SIZE-1; | 
|  |  | 
|  | #ifdef CONFIG_NET_POLL_CONTROLLER | 
|  | static void i596_poll_controller(struct net_device *dev); | 
|  | #endif | 
|  |  | 
|  |  | 
|  | static inline void CA(struct net_device *dev) | 
|  | { | 
|  | gsc_writel(0, dev->base_addr + PA_CHANNEL_ATTENTION); | 
|  | } | 
|  |  | 
|  |  | 
|  | static inline void MPU_PORT(struct net_device *dev, int c, dma_addr_t x) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  |  | 
|  | u32 v = (u32) (c) | (u32) (x); | 
|  | u16 a, b; | 
|  |  | 
|  | if (lp->options & OPT_SWAP_PORT) { | 
|  | a = v >> 16; | 
|  | b = v & 0xffff; | 
|  | } else { | 
|  | a = v & 0xffff; | 
|  | b = v >> 16; | 
|  | } | 
|  |  | 
|  | gsc_writel(a, dev->base_addr + PA_CPU_PORT_L_ACCESS); | 
|  | udelay(1); | 
|  | gsc_writel(b, dev->base_addr + PA_CPU_PORT_L_ACCESS); | 
|  | } | 
|  |  | 
|  |  | 
|  | static inline int wait_istat(struct net_device *dev, struct i596_private *lp, int delcnt, char *str) | 
|  | { | 
|  | CHECK_INV(&(lp->iscp), sizeof(struct i596_iscp)); | 
|  | while (--delcnt && lp->iscp.stat) { | 
|  | udelay(10); | 
|  | CHECK_INV(&(lp->iscp), sizeof(struct i596_iscp)); | 
|  | } | 
|  | if (!delcnt) { | 
|  | printk("%s: %s, iscp.stat %04x, didn't clear\n", | 
|  | dev->name, str, lp->iscp.stat); | 
|  | return -1; | 
|  | } | 
|  | else | 
|  | return 0; | 
|  | } | 
|  |  | 
|  |  | 
|  | static inline int wait_cmd(struct net_device *dev, struct i596_private *lp, int delcnt, char *str) | 
|  | { | 
|  | CHECK_INV(&(lp->scb), sizeof(struct i596_scb)); | 
|  | while (--delcnt && lp->scb.command) { | 
|  | udelay(10); | 
|  | CHECK_INV(&(lp->scb), sizeof(struct i596_scb)); | 
|  | } | 
|  | if (!delcnt) { | 
|  | printk("%s: %s, status %4.4x, cmd %4.4x.\n", | 
|  | dev->name, str, lp->scb.status, lp->scb.command); | 
|  | return -1; | 
|  | } | 
|  | else | 
|  | return 0; | 
|  | } | 
|  |  | 
|  |  | 
|  | static void i596_display_data(struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  | struct i596_cmd *cmd; | 
|  | struct i596_rfd *rfd; | 
|  | struct i596_rbd *rbd; | 
|  |  | 
|  | printk("lp and scp at %p, .sysbus = %08x, .iscp = %08x\n", | 
|  | &lp->scp, lp->scp.sysbus, lp->scp.iscp); | 
|  | printk("iscp at %p, iscp.stat = %08x, .scb = %08x\n", | 
|  | &lp->iscp, lp->iscp.stat, lp->iscp.scb); | 
|  | printk("scb at %p, scb.status = %04x, .command = %04x," | 
|  | " .cmd = %08x, .rfd = %08x\n", | 
|  | &lp->scb, lp->scb.status, lp->scb.command, | 
|  | lp->scb.cmd, lp->scb.rfd); | 
|  | printk("   errors: crc %x, align %x, resource %x," | 
|  | " over %x, rcvdt %x, short %x\n", | 
|  | lp->scb.crc_err, lp->scb.align_err, lp->scb.resource_err, | 
|  | lp->scb.over_err, lp->scb.rcvdt_err, lp->scb.short_err); | 
|  | cmd = lp->cmd_head; | 
|  | while (cmd != NULL) { | 
|  | printk("cmd at %p, .status = %04x, .command = %04x, .b_next = %08x\n", | 
|  | cmd, cmd->status, cmd->command, cmd->b_next); | 
|  | cmd = cmd->v_next; | 
|  | } | 
|  | rfd = lp->rfd_head; | 
|  | printk("rfd_head = %p\n", rfd); | 
|  | do { | 
|  | printk("   %p .stat %04x, .cmd %04x, b_next %08x, rbd %08x," | 
|  | " count %04x\n", | 
|  | rfd, rfd->stat, rfd->cmd, rfd->b_next, rfd->rbd, | 
|  | rfd->count); | 
|  | rfd = rfd->v_next; | 
|  | } while (rfd != lp->rfd_head); | 
|  | rbd = lp->rbd_head; | 
|  | printk("rbd_head = %p\n", rbd); | 
|  | do { | 
|  | printk("   %p .count %04x, b_next %08x, b_data %08x, size %04x\n", | 
|  | rbd, rbd->count, rbd->b_next, rbd->b_data, rbd->size); | 
|  | rbd = rbd->v_next; | 
|  | } while (rbd != lp->rbd_head); | 
|  | CHECK_INV(lp, sizeof(struct i596_private)); | 
|  | } | 
|  |  | 
|  |  | 
|  | #if defined(ENABLE_MVME16x_NET) || defined(ENABLE_BVME6000_NET) | 
|  | static void i596_error(int irq, void *dev_id, struct pt_regs *regs) | 
|  | { | 
|  | struct net_device *dev = dev_id; | 
|  | volatile unsigned char *pcc2 = (unsigned char *) 0xfff42000; | 
|  |  | 
|  | pcc2[0x28] = 1; | 
|  | pcc2[0x2b] = 0x1d; | 
|  | printk("%s: Error interrupt\n", dev->name); | 
|  | i596_display_data(dev); | 
|  | } | 
|  | #endif | 
|  |  | 
|  | #define virt_to_dma(lp,v) ((lp)->dma_addr + (dma_addr_t)((unsigned long)(v)-(unsigned long)(lp))) | 
|  |  | 
|  | static inline void init_rx_bufs(struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  | int i; | 
|  | struct i596_rfd *rfd; | 
|  | struct i596_rbd *rbd; | 
|  |  | 
|  | /* First build the Receive Buffer Descriptor List */ | 
|  |  | 
|  | for (i = 0, rbd = lp->rbds; i < rx_ring_size; i++, rbd++) { | 
|  | dma_addr_t dma_addr; | 
|  | struct sk_buff *skb = dev_alloc_skb(PKT_BUF_SZ + 4); | 
|  |  | 
|  | if (skb == NULL) | 
|  | panic("%s: alloc_skb() failed", __FILE__); | 
|  | skb_reserve(skb, 2); | 
|  | dma_addr = dma_map_single(lp->dev, skb->data,PKT_BUF_SZ, | 
|  | DMA_FROM_DEVICE); | 
|  | skb->dev = dev; | 
|  | rbd->v_next = rbd+1; | 
|  | rbd->b_next = WSWAPrbd(virt_to_dma(lp,rbd+1)); | 
|  | rbd->b_addr = WSWAPrbd(virt_to_dma(lp,rbd)); | 
|  | rbd->skb = skb; | 
|  | rbd->v_data = skb->data; | 
|  | rbd->b_data = WSWAPchar(dma_addr); | 
|  | rbd->size = PKT_BUF_SZ; | 
|  | } | 
|  | lp->rbd_head = lp->rbds; | 
|  | rbd = lp->rbds + rx_ring_size - 1; | 
|  | rbd->v_next = lp->rbds; | 
|  | rbd->b_next = WSWAPrbd(virt_to_dma(lp,lp->rbds)); | 
|  |  | 
|  | /* Now build the Receive Frame Descriptor List */ | 
|  |  | 
|  | for (i = 0, rfd = lp->rfds; i < rx_ring_size; i++, rfd++) { | 
|  | rfd->rbd = I596_NULL; | 
|  | rfd->v_next = rfd+1; | 
|  | rfd->v_prev = rfd-1; | 
|  | rfd->b_next = WSWAPrfd(virt_to_dma(lp,rfd+1)); | 
|  | rfd->cmd = CMD_FLEX; | 
|  | } | 
|  | lp->rfd_head = lp->rfds; | 
|  | lp->scb.rfd = WSWAPrfd(virt_to_dma(lp,lp->rfds)); | 
|  | rfd = lp->rfds; | 
|  | rfd->rbd = WSWAPrbd(virt_to_dma(lp,lp->rbd_head)); | 
|  | rfd->v_prev = lp->rfds + rx_ring_size - 1; | 
|  | rfd = lp->rfds + rx_ring_size - 1; | 
|  | rfd->v_next = lp->rfds; | 
|  | rfd->b_next = WSWAPrfd(virt_to_dma(lp,lp->rfds)); | 
|  | rfd->cmd = CMD_EOL|CMD_FLEX; | 
|  |  | 
|  | CHECK_WBACK_INV(lp, sizeof(struct i596_private)); | 
|  | } | 
|  |  | 
|  | static inline void remove_rx_bufs(struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  | struct i596_rbd *rbd; | 
|  | int i; | 
|  |  | 
|  | for (i = 0, rbd = lp->rbds; i < rx_ring_size; i++, rbd++) { | 
|  | if (rbd->skb == NULL) | 
|  | break; | 
|  | dma_unmap_single(lp->dev, | 
|  | (dma_addr_t)WSWAPchar(rbd->b_data), | 
|  | PKT_BUF_SZ, DMA_FROM_DEVICE); | 
|  | dev_kfree_skb(rbd->skb); | 
|  | } | 
|  | } | 
|  |  | 
|  |  | 
|  | static void rebuild_rx_bufs(struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  | int i; | 
|  |  | 
|  | /* Ensure rx frame/buffer descriptors are tidy */ | 
|  |  | 
|  | for (i = 0; i < rx_ring_size; i++) { | 
|  | lp->rfds[i].rbd = I596_NULL; | 
|  | lp->rfds[i].cmd = CMD_FLEX; | 
|  | } | 
|  | lp->rfds[rx_ring_size-1].cmd = CMD_EOL|CMD_FLEX; | 
|  | lp->rfd_head = lp->rfds; | 
|  | lp->scb.rfd = WSWAPrfd(virt_to_dma(lp,lp->rfds)); | 
|  | lp->rbd_head = lp->rbds; | 
|  | lp->rfds[0].rbd = WSWAPrbd(virt_to_dma(lp,lp->rbds)); | 
|  |  | 
|  | CHECK_WBACK_INV(lp, sizeof(struct i596_private)); | 
|  | } | 
|  |  | 
|  |  | 
|  | static int init_i596_mem(struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  | unsigned long flags; | 
|  |  | 
|  | disable_irq(dev->irq);	/* disable IRQs from LAN */ | 
|  | DEB(DEB_INIT, | 
|  | printk("RESET 82596 port: %lx (with IRQ %d disabled)\n", | 
|  | (dev->base_addr + PA_I82596_RESET), | 
|  | dev->irq)); | 
|  |  | 
|  | gsc_writel(0, (dev->base_addr + PA_I82596_RESET)); /* Hard Reset */ | 
|  | udelay(100);			/* Wait 100us - seems to help */ | 
|  |  | 
|  | /* change the scp address */ | 
|  |  | 
|  | lp->last_cmd = jiffies; | 
|  |  | 
|  |  | 
|  | lp->scp.sysbus = 0x0000006c; | 
|  | lp->scp.iscp = WSWAPiscp(virt_to_dma(lp,&(lp->iscp))); | 
|  | lp->iscp.scb = WSWAPscb(virt_to_dma(lp,&(lp->scb))); | 
|  | lp->iscp.stat = ISCP_BUSY; | 
|  | lp->cmd_backlog = 0; | 
|  |  | 
|  | lp->cmd_head = NULL; | 
|  | lp->scb.cmd = I596_NULL; | 
|  |  | 
|  | DEB(DEB_INIT, printk("%s: starting i82596.\n", dev->name)); | 
|  |  | 
|  | CHECK_WBACK(&(lp->scp), sizeof(struct i596_scp)); | 
|  | CHECK_WBACK(&(lp->iscp), sizeof(struct i596_iscp)); | 
|  |  | 
|  | MPU_PORT(dev, PORT_ALTSCP, virt_to_dma(lp,&lp->scp)); | 
|  |  | 
|  | CA(dev); | 
|  |  | 
|  | if (wait_istat(dev, lp, 1000, "initialization timed out")) | 
|  | goto failed; | 
|  | DEB(DEB_INIT, printk("%s: i82596 initialization successful\n", dev->name)); | 
|  |  | 
|  | /* Ensure rx frame/buffer descriptors are tidy */ | 
|  | rebuild_rx_bufs(dev); | 
|  |  | 
|  | lp->scb.command = 0; | 
|  | CHECK_WBACK(&(lp->scb), sizeof(struct i596_scb)); | 
|  |  | 
|  | enable_irq(dev->irq);	/* enable IRQs from LAN */ | 
|  |  | 
|  | DEB(DEB_INIT, printk("%s: queuing CmdConfigure\n", dev->name)); | 
|  | memcpy(lp->cf_cmd.i596_config, init_setup, 14); | 
|  | lp->cf_cmd.cmd.command = CmdConfigure; | 
|  | CHECK_WBACK(&(lp->cf_cmd), sizeof(struct cf_cmd)); | 
|  | i596_add_cmd(dev, &lp->cf_cmd.cmd); | 
|  |  | 
|  | DEB(DEB_INIT, printk("%s: queuing CmdSASetup\n", dev->name)); | 
|  | memcpy(lp->sa_cmd.eth_addr, dev->dev_addr, 6); | 
|  | lp->sa_cmd.cmd.command = CmdSASetup; | 
|  | CHECK_WBACK(&(lp->sa_cmd), sizeof(struct sa_cmd)); | 
|  | i596_add_cmd(dev, &lp->sa_cmd.cmd); | 
|  |  | 
|  | DEB(DEB_INIT, printk("%s: queuing CmdTDR\n", dev->name)); | 
|  | lp->tdr_cmd.cmd.command = CmdTDR; | 
|  | CHECK_WBACK(&(lp->tdr_cmd), sizeof(struct tdr_cmd)); | 
|  | i596_add_cmd(dev, &lp->tdr_cmd.cmd); | 
|  |  | 
|  | spin_lock_irqsave (&lp->lock, flags); | 
|  |  | 
|  | if (wait_cmd(dev, lp, 1000, "timed out waiting to issue RX_START")) { | 
|  | spin_unlock_irqrestore (&lp->lock, flags); | 
|  | goto failed; | 
|  | } | 
|  | DEB(DEB_INIT, printk("%s: Issuing RX_START\n", dev->name)); | 
|  | lp->scb.command = RX_START; | 
|  | lp->scb.rfd = WSWAPrfd(virt_to_dma(lp,lp->rfds)); | 
|  | CHECK_WBACK(&(lp->scb), sizeof(struct i596_scb)); | 
|  |  | 
|  | CA(dev); | 
|  |  | 
|  | spin_unlock_irqrestore (&lp->lock, flags); | 
|  |  | 
|  | if (wait_cmd(dev, lp, 1000, "RX_START not processed")) | 
|  | goto failed; | 
|  | DEB(DEB_INIT, printk("%s: Receive unit started OK\n", dev->name)); | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | failed: | 
|  | printk("%s: Failed to initialise 82596\n", dev->name); | 
|  | MPU_PORT(dev, PORT_RESET, 0); | 
|  | return -1; | 
|  | } | 
|  |  | 
|  |  | 
|  | static inline int i596_rx(struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  | struct i596_rfd *rfd; | 
|  | struct i596_rbd *rbd; | 
|  | int frames = 0; | 
|  |  | 
|  | DEB(DEB_RXFRAME, printk("i596_rx(), rfd_head %p, rbd_head %p\n", | 
|  | lp->rfd_head, lp->rbd_head)); | 
|  |  | 
|  |  | 
|  | rfd = lp->rfd_head;		/* Ref next frame to check */ | 
|  |  | 
|  | CHECK_INV(rfd, sizeof(struct i596_rfd)); | 
|  | while ((rfd->stat) & STAT_C) {	/* Loop while complete frames */ | 
|  | if (rfd->rbd == I596_NULL) | 
|  | rbd = NULL; | 
|  | else if (rfd->rbd == lp->rbd_head->b_addr) { | 
|  | rbd = lp->rbd_head; | 
|  | CHECK_INV(rbd, sizeof(struct i596_rbd)); | 
|  | } | 
|  | else { | 
|  | printk("%s: rbd chain broken!\n", dev->name); | 
|  | /* XXX Now what? */ | 
|  | rbd = NULL; | 
|  | } | 
|  | DEB(DEB_RXFRAME, printk("  rfd %p, rfd.rbd %08x, rfd.stat %04x\n", | 
|  | rfd, rfd->rbd, rfd->stat)); | 
|  |  | 
|  | if (rbd != NULL && ((rfd->stat) & STAT_OK)) { | 
|  | /* a good frame */ | 
|  | int pkt_len = rbd->count & 0x3fff; | 
|  | struct sk_buff *skb = rbd->skb; | 
|  | int rx_in_place = 0; | 
|  |  | 
|  | DEB(DEB_RXADDR,print_eth(rbd->v_data, "received")); | 
|  | frames++; | 
|  |  | 
|  | /* Check if the packet is long enough to just accept | 
|  | * without copying to a properly sized skbuff. | 
|  | */ | 
|  |  | 
|  | if (pkt_len > rx_copybreak) { | 
|  | struct sk_buff *newskb; | 
|  | dma_addr_t dma_addr; | 
|  |  | 
|  | dma_unmap_single(lp->dev,(dma_addr_t)WSWAPchar(rbd->b_data), PKT_BUF_SZ, DMA_FROM_DEVICE); | 
|  | /* Get fresh skbuff to replace filled one. */ | 
|  | newskb = dev_alloc_skb(PKT_BUF_SZ + 4); | 
|  | if (newskb == NULL) { | 
|  | skb = NULL;	/* drop pkt */ | 
|  | goto memory_squeeze; | 
|  | } | 
|  | skb_reserve(newskb, 2); | 
|  |  | 
|  | /* Pass up the skb already on the Rx ring. */ | 
|  | skb_put(skb, pkt_len); | 
|  | rx_in_place = 1; | 
|  | rbd->skb = newskb; | 
|  | newskb->dev = dev; | 
|  | dma_addr = dma_map_single(lp->dev, newskb->data, PKT_BUF_SZ, DMA_FROM_DEVICE); | 
|  | rbd->v_data = newskb->data; | 
|  | rbd->b_data = WSWAPchar(dma_addr); | 
|  | CHECK_WBACK_INV(rbd, sizeof(struct i596_rbd)); | 
|  | } | 
|  | else | 
|  | skb = dev_alloc_skb(pkt_len + 2); | 
|  | memory_squeeze: | 
|  | if (skb == NULL) { | 
|  | /* XXX tulip.c can defer packets here!! */ | 
|  | printk("%s: i596_rx Memory squeeze, dropping packet.\n", dev->name); | 
|  | lp->stats.rx_dropped++; | 
|  | } | 
|  | else { | 
|  | skb->dev = dev; | 
|  | if (!rx_in_place) { | 
|  | /* 16 byte align the data fields */ | 
|  | dma_sync_single_for_cpu(lp->dev, (dma_addr_t)WSWAPchar(rbd->b_data), PKT_BUF_SZ, DMA_FROM_DEVICE); | 
|  | skb_reserve(skb, 2); | 
|  | memcpy(skb_put(skb,pkt_len), rbd->v_data, pkt_len); | 
|  | dma_sync_single_for_device(lp->dev, (dma_addr_t)WSWAPchar(rbd->b_data), PKT_BUF_SZ, DMA_FROM_DEVICE); | 
|  | } | 
|  | skb->len = pkt_len; | 
|  | skb->protocol=eth_type_trans(skb,dev); | 
|  | netif_rx(skb); | 
|  | dev->last_rx = jiffies; | 
|  | lp->stats.rx_packets++; | 
|  | lp->stats.rx_bytes+=pkt_len; | 
|  | } | 
|  | } | 
|  | else { | 
|  | DEB(DEB_ERRORS, printk("%s: Error, rfd.stat = 0x%04x\n", | 
|  | dev->name, rfd->stat)); | 
|  | lp->stats.rx_errors++; | 
|  | if ((rfd->stat) & 0x0001) | 
|  | lp->stats.collisions++; | 
|  | if ((rfd->stat) & 0x0080) | 
|  | lp->stats.rx_length_errors++; | 
|  | if ((rfd->stat) & 0x0100) | 
|  | lp->stats.rx_over_errors++; | 
|  | if ((rfd->stat) & 0x0200) | 
|  | lp->stats.rx_fifo_errors++; | 
|  | if ((rfd->stat) & 0x0400) | 
|  | lp->stats.rx_frame_errors++; | 
|  | if ((rfd->stat) & 0x0800) | 
|  | lp->stats.rx_crc_errors++; | 
|  | if ((rfd->stat) & 0x1000) | 
|  | lp->stats.rx_length_errors++; | 
|  | } | 
|  |  | 
|  | /* Clear the buffer descriptor count and EOF + F flags */ | 
|  |  | 
|  | if (rbd != NULL && (rbd->count & 0x4000)) { | 
|  | rbd->count = 0; | 
|  | lp->rbd_head = rbd->v_next; | 
|  | CHECK_WBACK_INV(rbd, sizeof(struct i596_rbd)); | 
|  | } | 
|  |  | 
|  | /* Tidy the frame descriptor, marking it as end of list */ | 
|  |  | 
|  | rfd->rbd = I596_NULL; | 
|  | rfd->stat = 0; | 
|  | rfd->cmd = CMD_EOL|CMD_FLEX; | 
|  | rfd->count = 0; | 
|  |  | 
|  | /* Remove end-of-list from old end descriptor */ | 
|  |  | 
|  | rfd->v_prev->cmd = CMD_FLEX; | 
|  |  | 
|  | /* Update record of next frame descriptor to process */ | 
|  |  | 
|  | lp->scb.rfd = rfd->b_next; | 
|  | lp->rfd_head = rfd->v_next; | 
|  | CHECK_WBACK_INV(rfd->v_prev, sizeof(struct i596_rfd)); | 
|  | CHECK_WBACK_INV(rfd, sizeof(struct i596_rfd)); | 
|  | rfd = lp->rfd_head; | 
|  | CHECK_INV(rfd, sizeof(struct i596_rfd)); | 
|  | } | 
|  |  | 
|  | DEB(DEB_RXFRAME, printk("frames %d\n", frames)); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  |  | 
|  | static inline void i596_cleanup_cmd(struct net_device *dev, struct i596_private *lp) | 
|  | { | 
|  | struct i596_cmd *ptr; | 
|  |  | 
|  | while (lp->cmd_head != NULL) { | 
|  | ptr = lp->cmd_head; | 
|  | lp->cmd_head = ptr->v_next; | 
|  | lp->cmd_backlog--; | 
|  |  | 
|  | switch ((ptr->command) & 0x7) { | 
|  | case CmdTx: | 
|  | { | 
|  | struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; | 
|  | struct sk_buff *skb = tx_cmd->skb; | 
|  | dma_unmap_single(lp->dev, tx_cmd->dma_addr, skb->len, DMA_TO_DEVICE); | 
|  |  | 
|  | dev_kfree_skb(skb); | 
|  |  | 
|  | lp->stats.tx_errors++; | 
|  | lp->stats.tx_aborted_errors++; | 
|  |  | 
|  | ptr->v_next = NULL; | 
|  | ptr->b_next = I596_NULL; | 
|  | tx_cmd->cmd.command = 0;  /* Mark as free */ | 
|  | break; | 
|  | } | 
|  | default: | 
|  | ptr->v_next = NULL; | 
|  | ptr->b_next = I596_NULL; | 
|  | } | 
|  | CHECK_WBACK_INV(ptr, sizeof(struct i596_cmd)); | 
|  | } | 
|  |  | 
|  | wait_cmd(dev, lp, 100, "i596_cleanup_cmd timed out"); | 
|  | lp->scb.cmd = I596_NULL; | 
|  | CHECK_WBACK(&(lp->scb), sizeof(struct i596_scb)); | 
|  | } | 
|  |  | 
|  |  | 
|  | static inline void i596_reset(struct net_device *dev, struct i596_private *lp) | 
|  | { | 
|  | unsigned long flags; | 
|  |  | 
|  | DEB(DEB_RESET, printk("i596_reset\n")); | 
|  |  | 
|  | spin_lock_irqsave (&lp->lock, flags); | 
|  |  | 
|  | wait_cmd(dev, lp, 100, "i596_reset timed out"); | 
|  |  | 
|  | netif_stop_queue(dev); | 
|  |  | 
|  | /* FIXME: this command might cause an lpmc */ | 
|  | lp->scb.command = CUC_ABORT | RX_ABORT; | 
|  | CHECK_WBACK(&(lp->scb), sizeof(struct i596_scb)); | 
|  | CA(dev); | 
|  |  | 
|  | /* wait for shutdown */ | 
|  | wait_cmd(dev, lp, 1000, "i596_reset 2 timed out"); | 
|  | spin_unlock_irqrestore (&lp->lock, flags); | 
|  |  | 
|  | i596_cleanup_cmd(dev,lp); | 
|  | i596_rx(dev); | 
|  |  | 
|  | netif_start_queue(dev); | 
|  | init_i596_mem(dev); | 
|  | } | 
|  |  | 
|  |  | 
|  | static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  | unsigned long flags; | 
|  |  | 
|  | DEB(DEB_ADDCMD, printk("i596_add_cmd cmd_head %p\n", lp->cmd_head)); | 
|  |  | 
|  | cmd->status = 0; | 
|  | cmd->command |= (CMD_EOL | CMD_INTR); | 
|  | cmd->v_next = NULL; | 
|  | cmd->b_next = I596_NULL; | 
|  | CHECK_WBACK(cmd, sizeof(struct i596_cmd)); | 
|  |  | 
|  | spin_lock_irqsave (&lp->lock, flags); | 
|  |  | 
|  | if (lp->cmd_head != NULL) { | 
|  | lp->cmd_tail->v_next = cmd; | 
|  | lp->cmd_tail->b_next = WSWAPcmd(virt_to_dma(lp,&cmd->status)); | 
|  | CHECK_WBACK(lp->cmd_tail, sizeof(struct i596_cmd)); | 
|  | } else { | 
|  | lp->cmd_head = cmd; | 
|  | wait_cmd(dev, lp, 100, "i596_add_cmd timed out"); | 
|  | lp->scb.cmd = WSWAPcmd(virt_to_dma(lp,&cmd->status)); | 
|  | lp->scb.command = CUC_START; | 
|  | CHECK_WBACK(&(lp->scb), sizeof(struct i596_scb)); | 
|  | CA(dev); | 
|  | } | 
|  | lp->cmd_tail = cmd; | 
|  | lp->cmd_backlog++; | 
|  |  | 
|  | spin_unlock_irqrestore (&lp->lock, flags); | 
|  |  | 
|  | if (lp->cmd_backlog > max_cmd_backlog) { | 
|  | unsigned long tickssofar = jiffies - lp->last_cmd; | 
|  |  | 
|  | if (tickssofar < ticks_limit) | 
|  | return; | 
|  |  | 
|  | printk("%s: command unit timed out, status resetting.\n", dev->name); | 
|  | #if 1 | 
|  | i596_reset(dev, lp); | 
|  | #endif | 
|  | } | 
|  | } | 
|  |  | 
|  | #if 0 | 
|  | /* this function makes a perfectly adequate probe...  but we have a | 
|  | device list */ | 
|  | static int i596_test(struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  | volatile int *tint; | 
|  | u32 data; | 
|  |  | 
|  | tint = (volatile int *)(&(lp->scp)); | 
|  | data = virt_to_dma(lp,tint); | 
|  |  | 
|  | tint[1] = -1; | 
|  | CHECK_WBACK(tint,PAGE_SIZE); | 
|  |  | 
|  | MPU_PORT(dev, 1, data); | 
|  |  | 
|  | for(data = 1000000; data; data--) { | 
|  | CHECK_INV(tint,PAGE_SIZE); | 
|  | if(tint[1] != -1) | 
|  | break; | 
|  |  | 
|  | } | 
|  |  | 
|  | printk("i596_test result %d\n", tint[1]); | 
|  |  | 
|  | } | 
|  | #endif | 
|  |  | 
|  |  | 
|  | static int i596_open(struct net_device *dev) | 
|  | { | 
|  | DEB(DEB_OPEN, printk("%s: i596_open() irq %d.\n", dev->name, dev->irq)); | 
|  |  | 
|  | if (request_irq(dev->irq, &i596_interrupt, 0, "i82596", dev)) { | 
|  | printk("%s: IRQ %d not free\n", dev->name, dev->irq); | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | init_rx_bufs(dev); | 
|  |  | 
|  | if (init_i596_mem(dev)) { | 
|  | printk("%s: Failed to init memory\n", dev->name); | 
|  | goto out_remove_rx_bufs; | 
|  | } | 
|  |  | 
|  | netif_start_queue(dev); | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | out_remove_rx_bufs: | 
|  | remove_rx_bufs(dev); | 
|  | free_irq(dev->irq, dev); | 
|  | out: | 
|  | return -EAGAIN; | 
|  | } | 
|  |  | 
|  | static void i596_tx_timeout (struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  |  | 
|  | /* Transmitter timeout, serious problems. */ | 
|  | DEB(DEB_ERRORS, printk("%s: transmit timed out, status resetting.\n", | 
|  | dev->name)); | 
|  |  | 
|  | lp->stats.tx_errors++; | 
|  |  | 
|  | /* Try to restart the adaptor */ | 
|  | if (lp->last_restart == lp->stats.tx_packets) { | 
|  | DEB(DEB_ERRORS, printk("Resetting board.\n")); | 
|  | /* Shutdown and restart */ | 
|  | i596_reset (dev, lp); | 
|  | } else { | 
|  | /* Issue a channel attention signal */ | 
|  | DEB(DEB_ERRORS, printk("Kicking board.\n")); | 
|  | lp->scb.command = CUC_START | RX_START; | 
|  | CHECK_WBACK_INV(&(lp->scb), sizeof(struct i596_scb)); | 
|  | CA (dev); | 
|  | lp->last_restart = lp->stats.tx_packets; | 
|  | } | 
|  |  | 
|  | dev->trans_start = jiffies; | 
|  | netif_wake_queue (dev); | 
|  | } | 
|  |  | 
|  |  | 
|  | static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  | struct tx_cmd *tx_cmd; | 
|  | struct i596_tbd *tbd; | 
|  | short length = skb->len; | 
|  | dev->trans_start = jiffies; | 
|  |  | 
|  | DEB(DEB_STARTTX, printk("%s: i596_start_xmit(%x,%p) called\n", dev->name, | 
|  | skb->len, skb->data)); | 
|  |  | 
|  | if (length < ETH_ZLEN) { | 
|  | skb = skb_padto(skb, ETH_ZLEN); | 
|  | if (skb == NULL) | 
|  | return 0; | 
|  | length = ETH_ZLEN; | 
|  | } | 
|  |  | 
|  | netif_stop_queue(dev); | 
|  |  | 
|  | tx_cmd = lp->tx_cmds + lp->next_tx_cmd; | 
|  | tbd = lp->tbds + lp->next_tx_cmd; | 
|  |  | 
|  | if (tx_cmd->cmd.command) { | 
|  | DEB(DEB_ERRORS, printk("%s: xmit ring full, dropping packet.\n", | 
|  | dev->name)); | 
|  | lp->stats.tx_dropped++; | 
|  |  | 
|  | dev_kfree_skb(skb); | 
|  | } else { | 
|  | if (++lp->next_tx_cmd == TX_RING_SIZE) | 
|  | lp->next_tx_cmd = 0; | 
|  | tx_cmd->tbd = WSWAPtbd(virt_to_dma(lp,tbd)); | 
|  | tbd->next = I596_NULL; | 
|  |  | 
|  | tx_cmd->cmd.command = CMD_FLEX | CmdTx; | 
|  | tx_cmd->skb = skb; | 
|  |  | 
|  | tx_cmd->pad = 0; | 
|  | tx_cmd->size = 0; | 
|  | tbd->pad = 0; | 
|  | tbd->size = EOF | length; | 
|  |  | 
|  | tx_cmd->dma_addr = dma_map_single(lp->dev, skb->data, skb->len, | 
|  | DMA_TO_DEVICE); | 
|  | tbd->data = WSWAPchar(tx_cmd->dma_addr); | 
|  |  | 
|  | DEB(DEB_TXADDR,print_eth(skb->data, "tx-queued")); | 
|  | CHECK_WBACK_INV(tx_cmd, sizeof(struct tx_cmd)); | 
|  | CHECK_WBACK_INV(tbd, sizeof(struct i596_tbd)); | 
|  | i596_add_cmd(dev, &tx_cmd->cmd); | 
|  |  | 
|  | lp->stats.tx_packets++; | 
|  | lp->stats.tx_bytes += length; | 
|  | } | 
|  |  | 
|  | netif_start_queue(dev); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void print_eth(unsigned char *add, char *str) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | printk("i596 0x%p, ", add); | 
|  | for (i = 0; i < 6; i++) | 
|  | printk(" %02X", add[i + 6]); | 
|  | printk(" -->"); | 
|  | for (i = 0; i < 6; i++) | 
|  | printk(" %02X", add[i]); | 
|  | printk(" %02X%02X, %s\n", add[12], add[13], str); | 
|  | } | 
|  |  | 
|  |  | 
|  | #define LAN_PROM_ADDR	0xF0810000 | 
|  |  | 
|  | static int __devinit i82596_probe(struct net_device *dev, | 
|  | struct device *gen_dev) | 
|  | { | 
|  | int i; | 
|  | struct i596_private *lp; | 
|  | char eth_addr[6]; | 
|  | dma_addr_t dma_addr; | 
|  |  | 
|  | /* This lot is ensure things have been cache line aligned. */ | 
|  | if (sizeof(struct i596_rfd) != 32) { | 
|  | printk("82596: sizeof(struct i596_rfd) = %d\n", | 
|  | (int)sizeof(struct i596_rfd)); | 
|  | return -ENODEV; | 
|  | } | 
|  | if ((sizeof(struct i596_rbd) % 32) != 0) { | 
|  | printk("82596: sizeof(struct i596_rbd) = %d\n", | 
|  | (int)sizeof(struct i596_rbd)); | 
|  | return -ENODEV; | 
|  | } | 
|  | if ((sizeof(struct tx_cmd) % 32) != 0) { | 
|  | printk("82596: sizeof(struct tx_cmd) = %d\n", | 
|  | (int)sizeof(struct tx_cmd)); | 
|  | return -ENODEV; | 
|  | } | 
|  | if (sizeof(struct i596_tbd) != 32) { | 
|  | printk("82596: sizeof(struct i596_tbd) = %d\n", | 
|  | (int)sizeof(struct i596_tbd)); | 
|  | return -ENODEV; | 
|  | } | 
|  | #ifndef __LP64__ | 
|  | if (sizeof(struct i596_private) > 4096) { | 
|  | printk("82596: sizeof(struct i596_private) = %d\n", | 
|  | (int)sizeof(struct i596_private)); | 
|  | return -ENODEV; | 
|  | } | 
|  | #endif | 
|  |  | 
|  | if (!dev->base_addr || !dev->irq) | 
|  | return -ENODEV; | 
|  |  | 
|  | if (pdc_lan_station_id(eth_addr, dev->base_addr)) { | 
|  | for (i=0; i < 6; i++) { | 
|  | eth_addr[i] = gsc_readb(LAN_PROM_ADDR + i); | 
|  | } | 
|  | printk(KERN_INFO "%s: MAC of HP700 LAN read from EEPROM\n", __FILE__); | 
|  | } | 
|  |  | 
|  | dev->mem_start = (unsigned long) dma_alloc_noncoherent(gen_dev, | 
|  | sizeof(struct i596_private), &dma_addr, GFP_KERNEL); | 
|  | if (!dev->mem_start) { | 
|  | printk(KERN_ERR "%s: Couldn't get shared memory\n", __FILE__); | 
|  | return -ENOMEM; | 
|  | } | 
|  |  | 
|  | for (i = 0; i < 6; i++) | 
|  | dev->dev_addr[i] = eth_addr[i]; | 
|  |  | 
|  | /* The 82596-specific entries in the device structure. */ | 
|  | dev->open = i596_open; | 
|  | dev->stop = i596_close; | 
|  | dev->hard_start_xmit = i596_start_xmit; | 
|  | dev->get_stats = i596_get_stats; | 
|  | dev->set_multicast_list = set_multicast_list; | 
|  | dev->tx_timeout = i596_tx_timeout; | 
|  | dev->watchdog_timeo = TX_TIMEOUT; | 
|  | #ifdef CONFIG_NET_POLL_CONTROLLER | 
|  | dev->poll_controller = i596_poll_controller; | 
|  | #endif | 
|  |  | 
|  | dev->priv = (void *)(dev->mem_start); | 
|  |  | 
|  | lp = dev->priv; | 
|  | memset(lp, 0, sizeof(struct i596_private)); | 
|  |  | 
|  | lp->scb.command = 0; | 
|  | lp->scb.cmd = I596_NULL; | 
|  | lp->scb.rfd = I596_NULL; | 
|  | spin_lock_init(&lp->lock); | 
|  | lp->dma_addr = dma_addr; | 
|  | lp->dev = gen_dev; | 
|  |  | 
|  | CHECK_WBACK_INV(dev->mem_start, sizeof(struct i596_private)); | 
|  |  | 
|  | i = register_netdev(dev); | 
|  | if (i) { | 
|  | lp = dev->priv; | 
|  | dma_free_noncoherent(lp->dev, sizeof(struct i596_private), | 
|  | (void *)dev->mem_start, lp->dma_addr); | 
|  | return i; | 
|  | }; | 
|  |  | 
|  | DEB(DEB_PROBE, printk(KERN_INFO "%s: 82596 at %#3lx,", dev->name, dev->base_addr)); | 
|  | for (i = 0; i < 6; i++) | 
|  | DEB(DEB_PROBE, printk(" %2.2X", dev->dev_addr[i])); | 
|  | DEB(DEB_PROBE, printk(" IRQ %d.\n", dev->irq)); | 
|  | DEB(DEB_INIT, printk(KERN_INFO "%s: lp at 0x%p (%d bytes), lp->scb at 0x%p\n", | 
|  | dev->name, lp, (int)sizeof(struct i596_private), &lp->scb)); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_NET_POLL_CONTROLLER | 
|  | static void i596_poll_controller(struct net_device *dev) | 
|  | { | 
|  | disable_irq(dev->irq); | 
|  | i596_interrupt(dev->irq, dev, NULL); | 
|  | enable_irq(dev->irq); | 
|  | } | 
|  | #endif | 
|  |  | 
|  | static irqreturn_t i596_interrupt(int irq, void *dev_id, struct pt_regs *regs) | 
|  | { | 
|  | struct net_device *dev = dev_id; | 
|  | struct i596_private *lp; | 
|  | unsigned short status, ack_cmd = 0; | 
|  |  | 
|  | if (dev == NULL) { | 
|  | printk("%s: irq %d for unknown device.\n", __FUNCTION__, irq); | 
|  | return IRQ_NONE; | 
|  | } | 
|  |  | 
|  | lp = dev->priv; | 
|  |  | 
|  | spin_lock (&lp->lock); | 
|  |  | 
|  | wait_cmd(dev, lp, 100, "i596 interrupt, timeout"); | 
|  | status = lp->scb.status; | 
|  |  | 
|  | DEB(DEB_INTS, printk("%s: i596 interrupt, IRQ %d, status %4.4x.\n", | 
|  | dev->name, irq, status)); | 
|  |  | 
|  | ack_cmd = status & 0xf000; | 
|  |  | 
|  | if (!ack_cmd) { | 
|  | DEB(DEB_ERRORS, printk("%s: interrupt with no events\n", dev->name)); | 
|  | spin_unlock (&lp->lock); | 
|  | return IRQ_NONE; | 
|  | } | 
|  |  | 
|  | if ((status & 0x8000) || (status & 0x2000)) { | 
|  | struct i596_cmd *ptr; | 
|  |  | 
|  | if ((status & 0x8000)) | 
|  | DEB(DEB_INTS, printk("%s: i596 interrupt completed command.\n", dev->name)); | 
|  | if ((status & 0x2000)) | 
|  | DEB(DEB_INTS, printk("%s: i596 interrupt command unit inactive %x.\n", dev->name, status & 0x0700)); | 
|  |  | 
|  | while (lp->cmd_head != NULL) { | 
|  | CHECK_INV(lp->cmd_head, sizeof(struct i596_cmd)); | 
|  | if (!(lp->cmd_head->status & STAT_C)) | 
|  | break; | 
|  |  | 
|  | ptr = lp->cmd_head; | 
|  |  | 
|  | DEB(DEB_STATUS, printk("cmd_head->status = %04x, ->command = %04x\n", | 
|  | lp->cmd_head->status, lp->cmd_head->command)); | 
|  | lp->cmd_head = ptr->v_next; | 
|  | lp->cmd_backlog--; | 
|  |  | 
|  | switch ((ptr->command) & 0x7) { | 
|  | case CmdTx: | 
|  | { | 
|  | struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; | 
|  | struct sk_buff *skb = tx_cmd->skb; | 
|  |  | 
|  | if ((ptr->status) & STAT_OK) { | 
|  | DEB(DEB_TXADDR, print_eth(skb->data, "tx-done")); | 
|  | } else { | 
|  | lp->stats.tx_errors++; | 
|  | if ((ptr->status) & 0x0020) | 
|  | lp->stats.collisions++; | 
|  | if (!((ptr->status) & 0x0040)) | 
|  | lp->stats.tx_heartbeat_errors++; | 
|  | if ((ptr->status) & 0x0400) | 
|  | lp->stats.tx_carrier_errors++; | 
|  | if ((ptr->status) & 0x0800) | 
|  | lp->stats.collisions++; | 
|  | if ((ptr->status) & 0x1000) | 
|  | lp->stats.tx_aborted_errors++; | 
|  | } | 
|  | dma_unmap_single(lp->dev, tx_cmd->dma_addr, skb->len, DMA_TO_DEVICE); | 
|  | dev_kfree_skb_irq(skb); | 
|  |  | 
|  | tx_cmd->cmd.command = 0; /* Mark free */ | 
|  | break; | 
|  | } | 
|  | case CmdTDR: | 
|  | { | 
|  | unsigned short status = ((struct tdr_cmd *)ptr)->status; | 
|  |  | 
|  | if (status & 0x8000) { | 
|  | DEB(DEB_ANY, printk("%s: link ok.\n", dev->name)); | 
|  | } else { | 
|  | if (status & 0x4000) | 
|  | printk("%s: Transceiver problem.\n", dev->name); | 
|  | if (status & 0x2000) | 
|  | printk("%s: Termination problem.\n", dev->name); | 
|  | if (status & 0x1000) | 
|  | printk("%s: Short circuit.\n", dev->name); | 
|  |  | 
|  | DEB(DEB_TDR, printk("%s: Time %d.\n", dev->name, status & 0x07ff)); | 
|  | } | 
|  | break; | 
|  | } | 
|  | case CmdConfigure: | 
|  | /* Zap command so set_multicast_list() knows it is free */ | 
|  | ptr->command = 0; | 
|  | break; | 
|  | } | 
|  | ptr->v_next = NULL; | 
|  | ptr->b_next = I596_NULL; | 
|  | CHECK_WBACK(ptr, sizeof(struct i596_cmd)); | 
|  | lp->last_cmd = jiffies; | 
|  | } | 
|  |  | 
|  | /* This mess is arranging that only the last of any outstanding | 
|  | * commands has the interrupt bit set.  Should probably really | 
|  | * only add to the cmd queue when the CU is stopped. | 
|  | */ | 
|  | ptr = lp->cmd_head; | 
|  | while ((ptr != NULL) && (ptr != lp->cmd_tail)) { | 
|  | struct i596_cmd *prev = ptr; | 
|  |  | 
|  | ptr->command &= 0x1fff; | 
|  | ptr = ptr->v_next; | 
|  | CHECK_WBACK_INV(prev, sizeof(struct i596_cmd)); | 
|  | } | 
|  |  | 
|  | if ((lp->cmd_head != NULL)) | 
|  | ack_cmd |= CUC_START; | 
|  | lp->scb.cmd = WSWAPcmd(virt_to_dma(lp,&lp->cmd_head->status)); | 
|  | CHECK_WBACK_INV(&lp->scb, sizeof(struct i596_scb)); | 
|  | } | 
|  | if ((status & 0x1000) || (status & 0x4000)) { | 
|  | if ((status & 0x4000)) | 
|  | DEB(DEB_INTS, printk("%s: i596 interrupt received a frame.\n", dev->name)); | 
|  | i596_rx(dev); | 
|  | /* Only RX_START if stopped - RGH 07-07-96 */ | 
|  | if (status & 0x1000) { | 
|  | if (netif_running(dev)) { | 
|  | DEB(DEB_ERRORS, printk("%s: i596 interrupt receive unit inactive, status 0x%x\n", dev->name, status)); | 
|  | ack_cmd |= RX_START; | 
|  | lp->stats.rx_errors++; | 
|  | lp->stats.rx_fifo_errors++; | 
|  | rebuild_rx_bufs(dev); | 
|  | } | 
|  | } | 
|  | } | 
|  | wait_cmd(dev, lp, 100, "i596 interrupt, timeout"); | 
|  | lp->scb.command = ack_cmd; | 
|  | CHECK_WBACK(&lp->scb, sizeof(struct i596_scb)); | 
|  |  | 
|  | /* DANGER: I suspect that some kind of interrupt | 
|  | acknowledgement aside from acking the 82596 might be needed | 
|  | here...  but it's running acceptably without */ | 
|  |  | 
|  | CA(dev); | 
|  |  | 
|  | wait_cmd(dev, lp, 100, "i596 interrupt, exit timeout"); | 
|  | DEB(DEB_INTS, printk("%s: exiting interrupt.\n", dev->name)); | 
|  |  | 
|  | spin_unlock (&lp->lock); | 
|  | return IRQ_HANDLED; | 
|  | } | 
|  |  | 
|  | static int i596_close(struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  | unsigned long flags; | 
|  |  | 
|  | netif_stop_queue(dev); | 
|  |  | 
|  | DEB(DEB_INIT, printk("%s: Shutting down ethercard, status was %4.4x.\n", | 
|  | dev->name, lp->scb.status)); | 
|  |  | 
|  | spin_lock_irqsave(&lp->lock, flags); | 
|  |  | 
|  | wait_cmd(dev, lp, 100, "close1 timed out"); | 
|  | lp->scb.command = CUC_ABORT | RX_ABORT; | 
|  | CHECK_WBACK(&lp->scb, sizeof(struct i596_scb)); | 
|  |  | 
|  | CA(dev); | 
|  |  | 
|  | wait_cmd(dev, lp, 100, "close2 timed out"); | 
|  | spin_unlock_irqrestore(&lp->lock, flags); | 
|  | DEB(DEB_STRUCT,i596_display_data(dev)); | 
|  | i596_cleanup_cmd(dev,lp); | 
|  |  | 
|  | disable_irq(dev->irq); | 
|  |  | 
|  | free_irq(dev->irq, dev); | 
|  | remove_rx_bufs(dev); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static struct net_device_stats * | 
|  | i596_get_stats(struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  |  | 
|  | return &lp->stats; | 
|  | } | 
|  |  | 
|  | /* | 
|  | *    Set or clear the multicast filter for this adaptor. | 
|  | */ | 
|  |  | 
|  | static void set_multicast_list(struct net_device *dev) | 
|  | { | 
|  | struct i596_private *lp = dev->priv; | 
|  | int config = 0, cnt; | 
|  |  | 
|  | DEB(DEB_MULTI, printk("%s: set multicast list, %d entries, promisc %s, allmulti %s\n", | 
|  | dev->name, dev->mc_count, dev->flags & IFF_PROMISC ? "ON" : "OFF", | 
|  | dev->flags & IFF_ALLMULTI ? "ON" : "OFF")); | 
|  |  | 
|  | if ((dev->flags & IFF_PROMISC) && !(lp->cf_cmd.i596_config[8] & 0x01)) { | 
|  | lp->cf_cmd.i596_config[8] |= 0x01; | 
|  | config = 1; | 
|  | } | 
|  | if (!(dev->flags & IFF_PROMISC) && (lp->cf_cmd.i596_config[8] & 0x01)) { | 
|  | lp->cf_cmd.i596_config[8] &= ~0x01; | 
|  | config = 1; | 
|  | } | 
|  | if ((dev->flags & IFF_ALLMULTI) && (lp->cf_cmd.i596_config[11] & 0x20)) { | 
|  | lp->cf_cmd.i596_config[11] &= ~0x20; | 
|  | config = 1; | 
|  | } | 
|  | if (!(dev->flags & IFF_ALLMULTI) && !(lp->cf_cmd.i596_config[11] & 0x20)) { | 
|  | lp->cf_cmd.i596_config[11] |= 0x20; | 
|  | config = 1; | 
|  | } | 
|  | if (config) { | 
|  | if (lp->cf_cmd.cmd.command) | 
|  | printk("%s: config change request already queued\n", | 
|  | dev->name); | 
|  | else { | 
|  | lp->cf_cmd.cmd.command = CmdConfigure; | 
|  | CHECK_WBACK_INV(&lp->cf_cmd, sizeof(struct cf_cmd)); | 
|  | i596_add_cmd(dev, &lp->cf_cmd.cmd); | 
|  | } | 
|  | } | 
|  |  | 
|  | cnt = dev->mc_count; | 
|  | if (cnt > MAX_MC_CNT) | 
|  | { | 
|  | cnt = MAX_MC_CNT; | 
|  | printk("%s: Only %d multicast addresses supported", | 
|  | dev->name, cnt); | 
|  | } | 
|  |  | 
|  | if (dev->mc_count > 0) { | 
|  | struct dev_mc_list *dmi; | 
|  | unsigned char *cp; | 
|  | struct mc_cmd *cmd; | 
|  |  | 
|  | cmd = &lp->mc_cmd; | 
|  | cmd->cmd.command = CmdMulticastList; | 
|  | cmd->mc_cnt = dev->mc_count * 6; | 
|  | cp = cmd->mc_addrs; | 
|  | for (dmi = dev->mc_list; cnt && dmi != NULL; dmi = dmi->next, cnt--, cp += 6) { | 
|  | memcpy(cp, dmi->dmi_addr, 6); | 
|  | if (i596_debug > 1) | 
|  | DEB(DEB_MULTI, printk("%s: Adding address %02x:%02x:%02x:%02x:%02x:%02x\n", | 
|  | dev->name, cp[0],cp[1],cp[2],cp[3],cp[4],cp[5])); | 
|  | } | 
|  | CHECK_WBACK_INV(&lp->mc_cmd, sizeof(struct mc_cmd)); | 
|  | i596_add_cmd(dev, &cmd->cmd); | 
|  | } | 
|  | } | 
|  |  | 
|  | MODULE_PARM(debug, "i"); | 
|  | MODULE_PARM_DESC(debug, "lasi_82596 debug mask"); | 
|  | static int debug = -1; | 
|  |  | 
|  | static int num_drivers; | 
|  | static struct net_device *netdevs[MAX_DRIVERS]; | 
|  |  | 
|  | static int __devinit | 
|  | lan_init_chip(struct parisc_device *dev) | 
|  | { | 
|  | struct	net_device *netdevice; | 
|  | int	retval; | 
|  |  | 
|  | if (num_drivers >= MAX_DRIVERS) { | 
|  | /* max count of possible i82596 drivers reached */ | 
|  | return -ENOMEM; | 
|  | } | 
|  |  | 
|  | if (num_drivers == 0) | 
|  | printk(KERN_INFO LASI_82596_DRIVER_VERSION "\n"); | 
|  |  | 
|  | if (!dev->irq) { | 
|  | printk(KERN_ERR "%s: IRQ not found for i82596 at 0x%lx\n", | 
|  | __FILE__, dev->hpa.start); | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | printk(KERN_INFO "Found i82596 at 0x%lx, IRQ %d\n", dev->hpa.start, | 
|  | dev->irq); | 
|  |  | 
|  | netdevice = alloc_etherdev(0); | 
|  | if (!netdevice) | 
|  | return -ENOMEM; | 
|  |  | 
|  | netdevice->base_addr = dev->hpa.start; | 
|  | netdevice->irq = dev->irq; | 
|  |  | 
|  | retval = i82596_probe(netdevice, &dev->dev); | 
|  | if (retval) { | 
|  | free_netdev(netdevice); | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | if (dev->id.sversion == 0x72) { | 
|  | ((struct i596_private *)netdevice->priv)->options = OPT_SWAP_PORT; | 
|  | } | 
|  |  | 
|  | netdevs[num_drivers++] = netdevice; | 
|  |  | 
|  | return retval; | 
|  | } | 
|  |  | 
|  |  | 
|  | static struct parisc_device_id lan_tbl[] = { | 
|  | { HPHW_FIO, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x0008a }, | 
|  | { HPHW_FIO, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x00072 }, | 
|  | { 0, } | 
|  | }; | 
|  |  | 
|  | MODULE_DEVICE_TABLE(parisc, lan_tbl); | 
|  |  | 
|  | static struct parisc_driver lan_driver = { | 
|  | .name		= "lasi_82596", | 
|  | .id_table	= lan_tbl, | 
|  | .probe		= lan_init_chip, | 
|  | }; | 
|  |  | 
|  | static int __devinit lasi_82596_init(void) | 
|  | { | 
|  | if (debug >= 0) | 
|  | i596_debug = debug; | 
|  | return register_parisc_driver(&lan_driver); | 
|  | } | 
|  |  | 
|  | module_init(lasi_82596_init); | 
|  |  | 
|  | static void __exit lasi_82596_exit(void) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | for (i=0; i<MAX_DRIVERS; i++) { | 
|  | struct i596_private *lp; | 
|  | struct net_device *netdevice; | 
|  |  | 
|  | netdevice = netdevs[i]; | 
|  | if (!netdevice) | 
|  | continue; | 
|  |  | 
|  | unregister_netdev(netdevice); | 
|  |  | 
|  | lp = netdevice->priv; | 
|  | dma_free_noncoherent(lp->dev, sizeof(struct i596_private), | 
|  | (void *)netdevice->mem_start, lp->dma_addr); | 
|  | free_netdev(netdevice); | 
|  | } | 
|  | num_drivers = 0; | 
|  |  | 
|  | unregister_parisc_driver(&lan_driver); | 
|  | } | 
|  |  | 
|  | module_exit(lasi_82596_exit); |