msm: Configure wcd9xxx reset gpio level low
The wcd9xxx codec requires reset gpio to be active at boot time so that
reset is held while regulators are enabled.
The reset signal is active low. Configure gpio to level low.
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
(cherry picked from commit 187e9cbc9a886af94b9e13e6acf6a5d54e319b34)
Conflicts:
arch/arm/mach-msm/board-8064-pmic.c
arch/arm/mach-msm/board-8974-gpiomux.c
Change-Id: Ia2fcfa85565de2a00dabedae5b4a175de6a6a678
Signed-off-by: Sudhir Sharma <sudsha@codeaurora.org>
diff --git a/arch/arm/mach-msm/board-8064-pmic.c b/arch/arm/mach-msm/board-8064-pmic.c
index 6fa9367..a357cbd 100644
--- a/arch/arm/mach-msm/board-8064-pmic.c
+++ b/arch/arm/mach-msm/board-8064-pmic.c
@@ -126,7 +126,7 @@
PM8921_GPIO_INPUT(35, PM_GPIO_PULL_UP_30),
PM8921_GPIO_INPUT(38, PM_GPIO_PULL_UP_30),
/* TABLA CODEC RESET */
- PM8921_GPIO_OUTPUT(34, 1, HIGH),
+ PM8921_GPIO_OUTPUT(34, 0, MED),
PM8921_GPIO_OUTPUT(13, 0, HIGH), /* PCIE_CLK_PWR_EN */
PM8921_GPIO_INPUT(12, PM_GPIO_PULL_UP_30), /* PCIE_WAKE_N */
};
diff --git a/arch/arm/mach-msm/board-8930-gpiomux.c b/arch/arm/mach-msm/board-8930-gpiomux.c
index ff0a61f..7702d00 100644
--- a/arch/arm/mach-msm/board-8930-gpiomux.c
+++ b/arch/arm/mach-msm/board-8930-gpiomux.c
@@ -274,6 +274,13 @@
#endif
+static struct gpiomux_setting sitar_reset = {
+ .func = GPIOMUX_FUNC_GPIO,
+ .drv = GPIOMUX_DRV_6MA,
+ .pull = GPIOMUX_PULL_NONE,
+ .dir = GPIOMUX_OUT_LOW,
+};
+
#if defined(CONFIG_KS8851) || defined(CONFIG_KS8851_MODULE)
static struct msm_gpiomux_config msm8960_ethernet_configs[] = {
{
@@ -704,6 +711,15 @@
},
};
+static struct msm_gpiomux_config msm_sitar_config[] __initdata = {
+ {
+ .gpio = 42, /* SYS_RST_N */
+ .settings = {
+ [GPIOMUX_SUSPENDED] = &sitar_reset,
+ },
+ }
+};
+
int __init msm8930_init_gpiomux(void)
{
int rc = msm_gpiomux_init(NR_GPIO_IRQS);
@@ -778,5 +794,7 @@
msm_gpiomux_install(msm8930_gyro_int_config,
ARRAY_SIZE(msm8930_gyro_int_config));
+ msm_gpiomux_install(msm_sitar_config, ARRAY_SIZE(msm_sitar_config));
+
return 0;
}
diff --git a/arch/arm/mach-msm/board-8960-pmic.c b/arch/arm/mach-msm/board-8960-pmic.c
index 1d3fa00..5f10cc1 100644
--- a/arch/arm/mach-msm/board-8960-pmic.c
+++ b/arch/arm/mach-msm/board-8960-pmic.c
@@ -109,7 +109,7 @@
PM8XXX_GPIO_OUTPUT(43, 1), /* DISP_RESET_N */
PM8XXX_GPIO_OUTPUT(42, 0), /* USB 5V reg enable */
/* TABLA CODEC RESET */
- PM8XXX_GPIO_OUTPUT_STRENGTH(34, 1, PM_GPIO_STRENGTH_MED)
+ PM8XXX_GPIO_OUTPUT_STRENGTH(34, 0, PM_GPIO_STRENGTH_MED)
};
/* Initial PM8921 MPP configurations */
diff --git a/arch/arm/mach-msm/board-8974-gpiomux.c b/arch/arm/mach-msm/board-8974-gpiomux.c
index bf80262..458816b 100644
--- a/arch/arm/mach-msm/board-8974-gpiomux.c
+++ b/arch/arm/mach-msm/board-8974-gpiomux.c
@@ -61,6 +61,60 @@
};
+static struct gpiomux_setting lcd_en_sus_cfg = {
+ .func = GPIOMUX_FUNC_GPIO,
+ .drv = GPIOMUX_DRV_2MA,
+ .pull = GPIOMUX_PULL_DOWN,
+};
+
+static struct gpiomux_setting atmel_resout_sus_cfg = {
+ .func = GPIOMUX_FUNC_GPIO,
+ .drv = GPIOMUX_DRV_6MA,
+ .pull = GPIOMUX_PULL_DOWN,
+};
+
+static struct gpiomux_setting atmel_resout_act_cfg = {
+ .func = GPIOMUX_FUNC_GPIO,
+ .drv = GPIOMUX_DRV_6MA,
+ .pull = GPIOMUX_PULL_UP,
+};
+
+static struct gpiomux_setting atmel_int_act_cfg = {
+ .func = GPIOMUX_FUNC_GPIO,
+ .drv = GPIOMUX_DRV_8MA,
+ .pull = GPIOMUX_PULL_UP,
+};
+
+static struct gpiomux_setting atmel_int_sus_cfg = {
+ .func = GPIOMUX_FUNC_GPIO,
+ .drv = GPIOMUX_DRV_2MA,
+ .pull = GPIOMUX_PULL_DOWN,
+};
+
+static struct gpiomux_setting taiko_reset = {
+ .func = GPIOMUX_FUNC_GPIO,
+ .drv = GPIOMUX_DRV_6MA,
+ .pull = GPIOMUX_PULL_NONE,
+ .dir = GPIOMUX_OUT_LOW,
+};
+
+static struct msm_gpiomux_config msm_touch_configs[] __initdata = {
+ {
+ .gpio = 60, /* TOUCH RESET */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &atmel_resout_act_cfg,
+ [GPIOMUX_SUSPENDED] = &atmel_resout_sus_cfg,
+ },
+ },
+ {
+ .gpio = 61, /* TOUCH IRQ */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &atmel_int_act_cfg,
+ [GPIOMUX_SUSPENDED] = &atmel_int_sus_cfg,
+ },
+ },
+
+};
static struct msm_gpiomux_config msm_blsp_configs[] __initdata = {
#if defined(CONFIG_KS8851) || defined(CONFIG_KS8851_MODULE)
{
@@ -114,6 +168,179 @@
},
};
+static struct msm_gpiomux_config msm8974_slimbus_config[] __initdata = {
+ {
+ .gpio = 70, /* slimbus clk */
+ .settings = {
+ [GPIOMUX_SUSPENDED] = &slimbus,
+ },
+ },
+ {
+ .gpio = 71, /* slimbus data */
+ .settings = {
+ [GPIOMUX_SUSPENDED] = &slimbus,
+ },
+ },
+};
+
+static struct gpiomux_setting cam_settings[] = {
+ {
+ .func = GPIOMUX_FUNC_1, /*active 1*/
+ .drv = GPIOMUX_DRV_2MA,
+ .pull = GPIOMUX_PULL_NONE,
+ },
+
+ {
+ .func = GPIOMUX_FUNC_1, /*suspend*/
+ .drv = GPIOMUX_DRV_2MA,
+ .pull = GPIOMUX_PULL_DOWN,
+ },
+
+ {
+ .func = GPIOMUX_FUNC_1, /*i2c suspend*/
+ .drv = GPIOMUX_DRV_2MA,
+ .pull = GPIOMUX_PULL_KEEPER,
+ },
+};
+
+static struct msm_gpiomux_config msm_sensor_configs[] __initdata = {
+ {
+ .gpio = 15, /* CAM_MCLK0 */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 16, /* CAM_MCLK1 */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 17, /* CAM_MCLK2 */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 18, /* WEBCAM1_RESET_N / CAM_MCLK3 */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 19, /* CCI_I2C_SDA0 */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[2],
+ },
+ },
+ {
+ .gpio = 20, /* CCI_I2C_SCL0 */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[2],
+ },
+ },
+ {
+ .gpio = 21, /* CCI_I2C_SDA1 */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[2],
+ },
+ },
+ {
+ .gpio = 22, /* CCI_I2C_SCL1 */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[2],
+ },
+ },
+ {
+ .gpio = 23, /* FLASH_LED_EN */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 24, /* FLASH_LED_NOW */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 25, /* WEBCAM2_RESET_N */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 26, /* CAM_IRQ */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 27, /* OIS_SYNC */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 28, /* WEBCAM1_STANDBY */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 89, /* CAM1_STANDBY_N */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 90, /* CAM1_RST_N */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 91, /* CAM2_STANDBY_N */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+ {
+ .gpio = 92, /* CAM2_RST_N */
+ .settings = {
+ [GPIOMUX_ACTIVE] = &cam_settings[0],
+ [GPIOMUX_SUSPENDED] = &cam_settings[1],
+ },
+ },
+};
+
+static struct msm_gpiomux_config msm_taiko_config[] __initdata = {
+ {
+ .gpio = 63, /* SYS_RST_N */
+ .settings = {
+ [GPIOMUX_SUSPENDED] = &taiko_reset,
+ },
+ }
+};
+
void __init msm_8974_init_gpiomux(void)
{
int rc;
@@ -128,4 +355,13 @@
msm_gpiomux_install(msm_eth_configs, ARRAY_SIZE(msm_eth_configs));
#endif
msm_gpiomux_install(msm_blsp_configs, ARRAY_SIZE(msm_blsp_configs));
+
+ msm_gpiomux_install(msm8974_slimbus_config,
+ ARRAY_SIZE(msm8974_slimbus_config));
+
+ msm_gpiomux_install(msm_touch_configs, ARRAY_SIZE(msm_touch_configs));
+
+ msm_gpiomux_install(msm_sensor_configs, ARRAY_SIZE(msm_sensor_configs));
+
+ msm_gpiomux_install(msm_taiko_config, ARRAY_SIZE(msm_taiko_config));
}
diff --git a/arch/arm/mach-msm/board-9615-gpiomux.c b/arch/arm/mach-msm/board-9615-gpiomux.c
index 47a9835..9339638 100644
--- a/arch/arm/mach-msm/board-9615-gpiomux.c
+++ b/arch/arm/mach-msm/board-9615-gpiomux.c
@@ -119,6 +119,13 @@
.dir = GPIOMUX_IN,
};
+static struct gpiomux_setting tabla_reset = {
+ .func = GPIOMUX_FUNC_GPIO,
+ .drv = GPIOMUX_DRV_6MA,
+ .pull = GPIOMUX_PULL_NONE,
+ .dir = GPIOMUX_OUT_LOW,
+};
+
static struct msm_gpiomux_config msm9615_audio_codec_configs[] __initdata = {
{
.gpio = 24,
@@ -126,6 +133,12 @@
[GPIOMUX_SUSPENDED] = &cdc_mclk,
},
},
+ {
+ .gpio = 84, /* SYS_RST_N */
+ .settings = {
+ [GPIOMUX_SUSPENDED] = &tabla_reset,
+ },
+ }
};
static struct msm_gpiomux_config msm9615_sdcc2_configs[] __initdata = {