| #ifndef __PCI_SH4_H |
| #define __PCI_SH4_H |
| |
| #if defined(CONFIG_CPU_SUBTYPE_SH7780) || \ |
| defined(CONFIG_CPU_SUBTYPE_SH7785) || \ |
| defined(CONFIG_CPU_SUBTYPE_SH7763) |
| #include "pci-sh7780.h" |
| #else |
| #include "pci-sh7751.h" |
| #endif |
| |
| #include <asm/io.h> |
| |
| /* startup values */ |
| #define PCI_PROBE_BIOS 1 |
| #define PCI_PROBE_CONF1 2 |
| #define PCI_PROBE_CONF2 4 |
| #define PCI_NO_CHECKS 0x400 |
| #define PCI_ASSIGN_ROMS 0x1000 |
| #define PCI_BIOS_IRQ_SCAN 0x2000 |
| |
| #define SH4_PCICR 0x100 /* PCI Control Register */ |
| #define SH4_PCICR_PREFIX 0xA5000000 /* CR prefix for write */ |
| #define SH4_PCICR_FTO 0x00000400 /* TRDY/IRDY Enable */ |
| #define SH4_PCICR_TRSB 0x00000200 /* Target Read Single */ |
| #define SH4_PCICR_BSWP 0x00000100 /* Target Byte Swap */ |
| #define SH4_PCICR_PLUP 0x00000080 /* Enable PCI Pullup */ |
| #define SH4_PCICR_ARBM 0x00000040 /* PCI Arbitration Mode */ |
| #define SH4_PCICR_MD 0x00000030 /* MD9 and MD10 status */ |
| #define SH4_PCICR_SERR 0x00000008 /* SERR output assert */ |
| #define SH4_PCICR_INTA 0x00000004 /* INTA output assert */ |
| #define SH4_PCICR_PRST 0x00000002 /* PCI Reset Assert */ |
| #define SH4_PCICR_CFIN 0x00000001 /* Central Fun. Init Done */ |
| #define SH4_PCILSR0 0x104 /* PCI Local Space Register0 */ |
| #define SH4_PCILSR1 0x108 /* PCI Local Space Register1 */ |
| #define SH4_PCILAR0 0x10C /* PCI Local Addr Register1 */ |
| #define SH4_PCILAR1 0x110 /* PCI Local Addr Register1 */ |
| #define SH4_PCIINT 0x114 /* PCI Interrupt Register */ |
| #define SH4_PCIINT_MLCK 0x00008000 /* Master Lock Error */ |
| #define SH4_PCIINT_TABT 0x00004000 /* Target Abort Error */ |
| #define SH4_PCIINT_TRET 0x00000200 /* Target Retry Error */ |
| #define SH4_PCIINT_MFDE 0x00000100 /* Master Func. Disable Error */ |
| #define SH4_PCIINT_PRTY 0x00000080 /* Address Parity Error */ |
| #define SH4_PCIINT_SERR 0x00000040 /* SERR Detection Error */ |
| #define SH4_PCIINT_TWDP 0x00000020 /* Tgt. Write Parity Error */ |
| #define SH4_PCIINT_TRDP 0x00000010 /* Tgt. Read Parity Err Det. */ |
| #define SH4_PCIINT_MTABT 0x00000008 /* Master-Tgt. Abort Error */ |
| #define SH4_PCIINT_MMABT 0x00000004 /* Master-Master Abort Error */ |
| #define SH4_PCIINT_MWPD 0x00000002 /* Master Write PERR Detect */ |
| #define SH4_PCIINT_MRPD 0x00000001 /* Master Read PERR Detect */ |
| #define SH4_PCIINTM 0x118 /* PCI Interrupt Mask */ |
| #define SH4_PCIALR 0x11C /* Error Address Register */ |
| #define SH4_PCICLR 0x120 /* Error Command/Data */ |
| #define SH4_PCICLR_MPIO 0x80000000 |
| #define SH4_PCICLR_MDMA0 0x40000000 /* DMA0 Transfer Error */ |
| #define SH4_PCICLR_MDMA1 0x20000000 /* DMA1 Transfer Error */ |
| #define SH4_PCICLR_MDMA2 0x10000000 /* DMA2 Transfer Error */ |
| #define SH4_PCICLR_MDMA3 0x08000000 /* DMA3 Transfer Error */ |
| #define SH4_PCICLR_TGT 0x04000000 /* Target Transfer Error */ |
| #define SH4_PCICLR_CMDL 0x0000000F /* PCI Command at Error */ |
| #define SH4_PCIAINT 0x130 /* Arbiter Interrupt Register */ |
| #define SH4_PCIAINT_MBKN 0x00002000 /* Master Broken Interrupt */ |
| #define SH4_PCIAINT_TBTO 0x00001000 /* Target Bus Time Out */ |
| #define SH4_PCIAINT_MBTO 0x00001000 /* Master Bus Time Out */ |
| #define SH4_PCIAINT_TABT 0x00000008 /* Target Abort */ |
| #define SH4_PCIAINT_MABT 0x00000004 /* Master Abort */ |
| #define SH4_PCIAINT_RDPE 0x00000002 /* Read Data Parity Error */ |
| #define SH4_PCIAINT_WDPE 0x00000001 /* Write Data Parity Error */ |
| #define SH4_PCIAINTM 0x134 /* Arbiter Int. Mask Register */ |
| #define SH4_PCIBMLR 0x138 /* Error Bus Master Register */ |
| #define SH4_PCIBMLR_REQ4 0x00000010 /* REQ4 bus master at error */ |
| #define SH4_PCIBMLR_REQ3 0x00000008 /* REQ3 bus master at error */ |
| #define SH4_PCIBMLR_REQ2 0x00000004 /* REQ2 bus master at error */ |
| #define SH4_PCIBMLR_REQ1 0x00000002 /* REQ1 bus master at error */ |
| #define SH4_PCIBMLR_REQ0 0x00000001 /* REQ0 bus master at error */ |
| #define SH4_PCIDMABT 0x140 /* DMA Transfer Arb. Register */ |
| #define SH4_PCIDMABT_RRBN 0x00000001 /* DMA Arbitor Round-Robin */ |
| #define SH4_PCIDPA0 0x180 /* DMA0 Transfer Addr. */ |
| #define SH4_PCIDLA0 0x184 /* DMA0 Local Addr. */ |
| #define SH4_PCIDTC0 0x188 /* DMA0 Transfer Cnt. */ |
| #define SH4_PCIDCR0 0x18C /* DMA0 Control Register */ |
| #define SH4_PCIDCR_ALGN 0x00000600 /* DMA Alignment Mode */ |
| #define SH4_PCIDCR_MAST 0x00000100 /* DMA Termination Type */ |
| #define SH4_PCIDCR_INTM 0x00000080 /* DMA Interrupt Done Mask*/ |
| #define SH4_PCIDCR_INTS 0x00000040 /* DMA Interrupt Done Status */ |
| #define SH4_PCIDCR_LHLD 0x00000020 /* Local Address Control */ |
| #define SH4_PCIDCR_PHLD 0x00000010 /* PCI Address Control*/ |
| #define SH4_PCIDCR_IOSEL 0x00000008 /* PCI Address Space Type */ |
| #define SH4_PCIDCR_DIR 0x00000004 /* DMA Transfer Direction */ |
| #define SH4_PCIDCR_STOP 0x00000002 /* Force DMA Stop */ |
| #define SH4_PCIDCR_STRT 0x00000001 /* DMA Start */ |
| #define SH4_PCIDPA1 0x190 /* DMA1 Transfer Addr. */ |
| #define SH4_PCIDLA1 0x194 /* DMA1 Local Addr. */ |
| #define SH4_PCIDTC1 0x198 /* DMA1 Transfer Cnt. */ |
| #define SH4_PCIDCR1 0x19C /* DMA1 Control Register */ |
| #define SH4_PCIDPA2 0x1A0 /* DMA2 Transfer Addr. */ |
| #define SH4_PCIDLA2 0x1A4 /* DMA2 Local Addr. */ |
| #define SH4_PCIDTC2 0x1A8 /* DMA2 Transfer Cnt. */ |
| #define SH4_PCIDCR2 0x1AC /* DMA2 Control Register */ |
| #define SH4_PCIDPA3 0x1B0 /* DMA3 Transfer Addr. */ |
| #define SH4_PCIDLA3 0x1B4 /* DMA3 Local Addr. */ |
| #define SH4_PCIDTC3 0x1B8 /* DMA3 Transfer Cnt. */ |
| #define SH4_PCIDCR3 0x1BC /* DMA3 Control Register */ |
| #define SH4_PCIPAR 0x1C0 /* PIO Address Register */ |
| #define SH4_PCIPAR_CFGEN 0x80000000 /* Configuration Enable */ |
| #define SH4_PCIPAR_BUSNO 0x00FF0000 /* Config. Bus Number */ |
| #define SH4_PCIPAR_DEVNO 0x0000FF00 /* Config. Device Number */ |
| #define SH4_PCIPAR_REGAD 0x000000FC /* Register Address Number */ |
| #define SH4_PCIMBR 0x1C4 /* Memory Base Address */ |
| #define SH4_PCIMBR_MASK 0xFF000000 /* Memory Space Mask */ |
| #define SH4_PCIMBR_LOCK 0x00000001 /* Lock Memory Space */ |
| #define SH4_PCIIOBR 0x1C8 /* I/O Base Address Register */ |
| #define SH4_PCIIOBR_MASK 0xFFFC0000 /* IO Space Mask */ |
| #define SH4_PCIIOBR_LOCK 0x00000001 /* Lock IO Space */ |
| #define SH4_PCIPINT 0x1CC /* Power Mgmnt Int. Register */ |
| #define SH4_PCIPINT_D3 0x00000002 /* D3 Pwr Mgmt. Interrupt */ |
| #define SH4_PCIPINT_D0 0x00000001 /* D0 Pwr Mgmt. Interrupt */ |
| #define SH4_PCIPINTM 0x1D0 /* Power Mgmnt Mask Register */ |
| #define SH4_PCICLKR 0x1D4 /* Clock Ctrl. Register */ |
| #define SH4_PCICLKR_PCSTP 0x00000002 /* PCI Clock Stop */ |
| #define SH4_PCICLKR_BCSTP 0x00000001 /* BCLK Clock Stop */ |
| /* For definitions of BCR, MCR see ... */ |
| #define SH4_PCIBCR1 0x1E0 /* Memory BCR1 Register */ |
| #define SH4_PCIMBR0 SH4_PCIBCR1 |
| #define SH4_PCIBCR2 0x1E4 /* Memory BCR2 Register */ |
| #define SH4_PCIMBMR0 SH4_PCIBCR2 |
| #define SH4_PCIWCR1 0x1E8 /* Wait Control 1 Register */ |
| #define SH4_PCIWCR2 0x1EC /* Wait Control 2 Register */ |
| #define SH4_PCIWCR3 0x1F0 /* Wait Control 3 Register */ |
| #define SH4_PCIMBR2 SH4_PCIWCR3 |
| #define SH4_PCIMCR 0x1F4 /* Memory Control Register */ |
| #define SH4_PCIBCR3 0x1f8 /* Memory BCR3 Register */ |
| #define SH4_PCIPCTR 0x200 /* Port Control Register */ |
| #define SH4_PCIPCTR_P2EN 0x000400000 /* Port 2 Enable */ |
| #define SH4_PCIPCTR_P1EN 0x000200000 /* Port 1 Enable */ |
| #define SH4_PCIPCTR_P0EN 0x000100000 /* Port 0 Enable */ |
| #define SH4_PCIPCTR_P2UP 0x000000020 /* Port2 Pull Up Enable */ |
| #define SH4_PCIPCTR_P2IO 0x000000010 /* Port2 Output Enable */ |
| #define SH4_PCIPCTR_P1UP 0x000000008 /* Port1 Pull Up Enable */ |
| #define SH4_PCIPCTR_P1IO 0x000000004 /* Port1 Output Enable */ |
| #define SH4_PCIPCTR_P0UP 0x000000002 /* Port0 Pull Up Enable */ |
| #define SH4_PCIPCTR_P0IO 0x000000001 /* Port0 Output Enable */ |
| #define SH4_PCIPDTR 0x204 /* Port Data Register */ |
| #define SH4_PCIPDTR_PB5 0x000000020 /* Port 5 Enable */ |
| #define SH4_PCIPDTR_PB4 0x000000010 /* Port 4 Enable */ |
| #define SH4_PCIPDTR_PB3 0x000000008 /* Port 3 Enable */ |
| #define SH4_PCIPDTR_PB2 0x000000004 /* Port 2 Enable */ |
| #define SH4_PCIPDTR_PB1 0x000000002 /* Port 1 Enable */ |
| #define SH4_PCIPDTR_PB0 0x000000001 /* Port 0 Enable */ |
| #define SH4_PCIPDR 0x220 /* Port IO Data Register */ |
| |
| /* Flags */ |
| #define SH4_PCIC_NO_RESET 0x0001 |
| |
| /* arch/sh/kernel/drivers/pci/ops-sh4.c */ |
| extern struct pci_ops sh4_pci_ops; |
| int sh4_pci_check_direct(void); |
| int pci_fixup_pcic(void); |
| |
| struct sh4_pci_address_space { |
| unsigned long base; |
| unsigned long size; |
| }; |
| |
| struct sh4_pci_address_map { |
| struct sh4_pci_address_space window0; |
| struct sh4_pci_address_space window1; |
| unsigned long flags; |
| }; |
| |
| static inline void pci_write_reg(unsigned long val, unsigned long reg) |
| { |
| ctrl_outl(val, PCI_REG(reg)); |
| } |
| |
| static inline unsigned long pci_read_reg(unsigned long reg) |
| { |
| return ctrl_inl(PCI_REG(reg)); |
| } |
| #endif /* __PCI_SH4_H */ |