|  | /* | 
|  | * Copyright (C) 2008 Felix Fietkau <nbd@openwrt.org> | 
|  | * | 
|  | * This program is free software; you can redistribute it and/or modify | 
|  | * it under the terms of the GNU General Public License version 2 as | 
|  | * published by the Free Software Foundation. | 
|  | * | 
|  | * Based on minstrel.c: | 
|  | *   Copyright (C) 2005-2007 Derek Smithies <derek@indranet.co.nz> | 
|  | *   Sponsored by Indranet Technologies Ltd | 
|  | * | 
|  | * Based on sample.c: | 
|  | *   Copyright (c) 2005 John Bicket | 
|  | *   All rights reserved. | 
|  | * | 
|  | *   Redistribution and use in source and binary forms, with or without | 
|  | *   modification, are permitted provided that the following conditions | 
|  | *   are met: | 
|  | *   1. Redistributions of source code must retain the above copyright | 
|  | *      notice, this list of conditions and the following disclaimer, | 
|  | *      without modification. | 
|  | *   2. Redistributions in binary form must reproduce at minimum a disclaimer | 
|  | *      similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any | 
|  | *      redistribution must be conditioned upon including a substantially | 
|  | *      similar Disclaimer requirement for further binary redistribution. | 
|  | *   3. Neither the names of the above-listed copyright holders nor the names | 
|  | *      of any contributors may be used to endorse or promote products derived | 
|  | *      from this software without specific prior written permission. | 
|  | * | 
|  | *   Alternatively, this software may be distributed under the terms of the | 
|  | *   GNU General Public License ("GPL") version 2 as published by the Free | 
|  | *   Software Foundation. | 
|  | * | 
|  | *   NO WARRANTY | 
|  | *   THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS | 
|  | *   ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT | 
|  | *   LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY | 
|  | *   AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL | 
|  | *   THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, | 
|  | *   OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF | 
|  | *   SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS | 
|  | *   INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER | 
|  | *   IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) | 
|  | *   ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF | 
|  | *   THE POSSIBILITY OF SUCH DAMAGES. | 
|  | */ | 
|  | #include <linux/netdevice.h> | 
|  | #include <linux/types.h> | 
|  | #include <linux/skbuff.h> | 
|  | #include <linux/debugfs.h> | 
|  | #include <linux/random.h> | 
|  | #include <linux/ieee80211.h> | 
|  | #include <net/mac80211.h> | 
|  | #include "rate.h" | 
|  | #include "rc80211_minstrel.h" | 
|  |  | 
|  | #define SAMPLE_COLUMNS	10 | 
|  | #define SAMPLE_TBL(_mi, _idx, _col) \ | 
|  | _mi->sample_table[(_idx * SAMPLE_COLUMNS) + _col] | 
|  |  | 
|  | /* convert mac80211 rate index to local array index */ | 
|  | static inline int | 
|  | rix_to_ndx(struct minstrel_sta_info *mi, int rix) | 
|  | { | 
|  | int i = rix; | 
|  | for (i = rix; i >= 0; i--) | 
|  | if (mi->r[i].rix == rix) | 
|  | break; | 
|  | WARN_ON(mi->r[i].rix != rix); | 
|  | return i; | 
|  | } | 
|  |  | 
|  | static inline bool | 
|  | use_low_rate(struct sk_buff *skb) | 
|  | { | 
|  | struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data; | 
|  | struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); | 
|  | u16 fc; | 
|  |  | 
|  | fc = le16_to_cpu(hdr->frame_control); | 
|  |  | 
|  | return ((info->flags & IEEE80211_TX_CTL_NO_ACK) || | 
|  | (fc & IEEE80211_FCTL_FTYPE) != IEEE80211_FTYPE_DATA || | 
|  | is_multicast_ether_addr(hdr->addr1)); | 
|  | } | 
|  |  | 
|  |  | 
|  | static void | 
|  | minstrel_update_stats(struct minstrel_priv *mp, struct minstrel_sta_info *mi) | 
|  | { | 
|  | u32 max_tp = 0, index_max_tp = 0, index_max_tp2 = 0; | 
|  | u32 max_prob = 0, index_max_prob = 0; | 
|  | u32 usecs; | 
|  | u32 p; | 
|  | int i; | 
|  |  | 
|  | mi->stats_update = jiffies; | 
|  | for (i = 0; i < mi->n_rates; i++) { | 
|  | struct minstrel_rate *mr = &mi->r[i]; | 
|  |  | 
|  | usecs = mr->perfect_tx_time; | 
|  | if (!usecs) | 
|  | usecs = 1000000; | 
|  |  | 
|  | /* To avoid rounding issues, probabilities scale from 0 (0%) | 
|  | * to 18000 (100%) */ | 
|  | if (mr->attempts) { | 
|  | p = (mr->success * 18000) / mr->attempts; | 
|  | mr->succ_hist += mr->success; | 
|  | mr->att_hist += mr->attempts; | 
|  | mr->cur_prob = p; | 
|  | p = ((p * (100 - mp->ewma_level)) + (mr->probability * | 
|  | mp->ewma_level)) / 100; | 
|  | mr->probability = p; | 
|  | mr->cur_tp = p * (1000000 / usecs); | 
|  | } | 
|  |  | 
|  | mr->last_success = mr->success; | 
|  | mr->last_attempts = mr->attempts; | 
|  | mr->success = 0; | 
|  | mr->attempts = 0; | 
|  |  | 
|  | /* Sample less often below the 10% chance of success. | 
|  | * Sample less often above the 95% chance of success. */ | 
|  | if ((mr->probability > 17100) || (mr->probability < 1800)) { | 
|  | mr->adjusted_retry_count = mr->retry_count >> 1; | 
|  | if (mr->adjusted_retry_count > 2) | 
|  | mr->adjusted_retry_count = 2; | 
|  | mr->sample_limit = 4; | 
|  | } else { | 
|  | mr->sample_limit = -1; | 
|  | mr->adjusted_retry_count = mr->retry_count; | 
|  | } | 
|  | if (!mr->adjusted_retry_count) | 
|  | mr->adjusted_retry_count = 2; | 
|  | } | 
|  |  | 
|  | for (i = 0; i < mi->n_rates; i++) { | 
|  | struct minstrel_rate *mr = &mi->r[i]; | 
|  | if (max_tp < mr->cur_tp) { | 
|  | index_max_tp = i; | 
|  | max_tp = mr->cur_tp; | 
|  | } | 
|  | if (max_prob < mr->probability) { | 
|  | index_max_prob = i; | 
|  | max_prob = mr->probability; | 
|  | } | 
|  | } | 
|  |  | 
|  | max_tp = 0; | 
|  | for (i = 0; i < mi->n_rates; i++) { | 
|  | struct minstrel_rate *mr = &mi->r[i]; | 
|  |  | 
|  | if (i == index_max_tp) | 
|  | continue; | 
|  |  | 
|  | if (max_tp < mr->cur_tp) { | 
|  | index_max_tp2 = i; | 
|  | max_tp = mr->cur_tp; | 
|  | } | 
|  | } | 
|  | mi->max_tp_rate = index_max_tp; | 
|  | mi->max_tp_rate2 = index_max_tp2; | 
|  | mi->max_prob_rate = index_max_prob; | 
|  | } | 
|  |  | 
|  | static void | 
|  | minstrel_tx_status(void *priv, struct ieee80211_supported_band *sband, | 
|  | struct ieee80211_sta *sta, void *priv_sta, | 
|  | struct sk_buff *skb) | 
|  | { | 
|  | struct minstrel_sta_info *mi = priv_sta; | 
|  | struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); | 
|  | struct ieee80211_tx_rate *ar = info->status.rates; | 
|  | int i, ndx; | 
|  | int success; | 
|  |  | 
|  | success = !!(info->flags & IEEE80211_TX_STAT_ACK); | 
|  |  | 
|  | for (i = 0; i < IEEE80211_TX_MAX_RATES; i++) { | 
|  | if (ar[i].idx < 0) | 
|  | break; | 
|  |  | 
|  | ndx = rix_to_ndx(mi, ar[i].idx); | 
|  | mi->r[ndx].attempts += ar[i].count; | 
|  |  | 
|  | if ((i != IEEE80211_TX_MAX_RATES - 1) && (ar[i + 1].idx < 0)) | 
|  | mi->r[ndx].success += success; | 
|  | } | 
|  |  | 
|  | if ((info->flags & IEEE80211_TX_CTL_RATE_CTRL_PROBE) && (i >= 0)) | 
|  | mi->sample_count++; | 
|  |  | 
|  | if (mi->sample_deferred > 0) | 
|  | mi->sample_deferred--; | 
|  | } | 
|  |  | 
|  |  | 
|  | static inline unsigned int | 
|  | minstrel_get_retry_count(struct minstrel_rate *mr, | 
|  | struct ieee80211_tx_info *info) | 
|  | { | 
|  | unsigned int retry = mr->adjusted_retry_count; | 
|  |  | 
|  | if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_RTS_CTS) | 
|  | retry = max(2U, min(mr->retry_count_rtscts, retry)); | 
|  | else if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_CTS_PROTECT) | 
|  | retry = max(2U, min(mr->retry_count_cts, retry)); | 
|  | return retry; | 
|  | } | 
|  |  | 
|  |  | 
|  | static int | 
|  | minstrel_get_next_sample(struct minstrel_sta_info *mi) | 
|  | { | 
|  | unsigned int sample_ndx; | 
|  | sample_ndx = SAMPLE_TBL(mi, mi->sample_idx, mi->sample_column); | 
|  | mi->sample_idx++; | 
|  | if (mi->sample_idx > (mi->n_rates - 2)) { | 
|  | mi->sample_idx = 0; | 
|  | mi->sample_column++; | 
|  | if (mi->sample_column >= SAMPLE_COLUMNS) | 
|  | mi->sample_column = 0; | 
|  | } | 
|  | return sample_ndx; | 
|  | } | 
|  |  | 
|  | static void | 
|  | minstrel_get_rate(void *priv, struct ieee80211_sta *sta, | 
|  | void *priv_sta, struct ieee80211_tx_rate_control *txrc) | 
|  | { | 
|  | struct sk_buff *skb = txrc->skb; | 
|  | struct ieee80211_supported_band *sband = txrc->sband; | 
|  | struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); | 
|  | struct minstrel_sta_info *mi = priv_sta; | 
|  | struct minstrel_priv *mp = priv; | 
|  | struct ieee80211_tx_rate *ar = info->control.rates; | 
|  | unsigned int ndx, sample_ndx = 0; | 
|  | bool mrr; | 
|  | bool sample_slower = false; | 
|  | bool sample = false; | 
|  | int i, delta; | 
|  | int mrr_ndx[3]; | 
|  | int sample_rate; | 
|  |  | 
|  | if (!sta || !mi || use_low_rate(skb)) { | 
|  | ar[0].idx = rate_lowest_index(sband, sta); | 
|  | ar[0].count = mp->max_retry; | 
|  | return; | 
|  | } | 
|  |  | 
|  | mrr = mp->has_mrr && !txrc->rts && !txrc->bss_conf->use_cts_prot; | 
|  |  | 
|  | if (time_after(jiffies, mi->stats_update + (mp->update_interval * | 
|  | HZ) / 1000)) | 
|  | minstrel_update_stats(mp, mi); | 
|  |  | 
|  | ndx = mi->max_tp_rate; | 
|  |  | 
|  | if (mrr) | 
|  | sample_rate = mp->lookaround_rate_mrr; | 
|  | else | 
|  | sample_rate = mp->lookaround_rate; | 
|  |  | 
|  | mi->packet_count++; | 
|  | delta = (mi->packet_count * sample_rate / 100) - | 
|  | (mi->sample_count + mi->sample_deferred / 2); | 
|  |  | 
|  | /* delta > 0: sampling required */ | 
|  | if ((delta > 0) && (mrr || !mi->prev_sample)) { | 
|  | struct minstrel_rate *msr; | 
|  | if (mi->packet_count >= 10000) { | 
|  | mi->sample_deferred = 0; | 
|  | mi->sample_count = 0; | 
|  | mi->packet_count = 0; | 
|  | } else if (delta > mi->n_rates * 2) { | 
|  | /* With multi-rate retry, not every planned sample | 
|  | * attempt actually gets used, due to the way the retry | 
|  | * chain is set up - [max_tp,sample,prob,lowest] for | 
|  | * sample_rate < max_tp. | 
|  | * | 
|  | * If there's too much sampling backlog and the link | 
|  | * starts getting worse, minstrel would start bursting | 
|  | * out lots of sampling frames, which would result | 
|  | * in a large throughput loss. */ | 
|  | mi->sample_count += (delta - mi->n_rates * 2); | 
|  | } | 
|  |  | 
|  | sample_ndx = minstrel_get_next_sample(mi); | 
|  | msr = &mi->r[sample_ndx]; | 
|  | sample = true; | 
|  | sample_slower = mrr && (msr->perfect_tx_time > | 
|  | mi->r[ndx].perfect_tx_time); | 
|  |  | 
|  | if (!sample_slower) { | 
|  | if (msr->sample_limit != 0) { | 
|  | ndx = sample_ndx; | 
|  | mi->sample_count++; | 
|  | if (msr->sample_limit > 0) | 
|  | msr->sample_limit--; | 
|  | } else { | 
|  | sample = false; | 
|  | } | 
|  | } else { | 
|  | /* Only use IEEE80211_TX_CTL_RATE_CTRL_PROBE to mark | 
|  | * packets that have the sampling rate deferred to the | 
|  | * second MRR stage. Increase the sample counter only | 
|  | * if the deferred sample rate was actually used. | 
|  | * Use the sample_deferred counter to make sure that | 
|  | * the sampling is not done in large bursts */ | 
|  | info->flags |= IEEE80211_TX_CTL_RATE_CTRL_PROBE; | 
|  | mi->sample_deferred++; | 
|  | } | 
|  | } | 
|  | mi->prev_sample = sample; | 
|  |  | 
|  | /* If we're not using MRR and the sampling rate already | 
|  | * has a probability of >95%, we shouldn't be attempting | 
|  | * to use it, as this only wastes precious airtime */ | 
|  | if (!mrr && sample && (mi->r[ndx].probability > 17100)) | 
|  | ndx = mi->max_tp_rate; | 
|  |  | 
|  | ar[0].idx = mi->r[ndx].rix; | 
|  | ar[0].count = minstrel_get_retry_count(&mi->r[ndx], info); | 
|  |  | 
|  | if (!mrr) { | 
|  | if (!sample) | 
|  | ar[0].count = mp->max_retry; | 
|  | ar[1].idx = mi->lowest_rix; | 
|  | ar[1].count = mp->max_retry; | 
|  | return; | 
|  | } | 
|  |  | 
|  | /* MRR setup */ | 
|  | if (sample) { | 
|  | if (sample_slower) | 
|  | mrr_ndx[0] = sample_ndx; | 
|  | else | 
|  | mrr_ndx[0] = mi->max_tp_rate; | 
|  | } else { | 
|  | mrr_ndx[0] = mi->max_tp_rate2; | 
|  | } | 
|  | mrr_ndx[1] = mi->max_prob_rate; | 
|  | mrr_ndx[2] = 0; | 
|  | for (i = 1; i < 4; i++) { | 
|  | ar[i].idx = mi->r[mrr_ndx[i - 1]].rix; | 
|  | ar[i].count = mi->r[mrr_ndx[i - 1]].adjusted_retry_count; | 
|  | } | 
|  | } | 
|  |  | 
|  |  | 
|  | static void | 
|  | calc_rate_durations(struct minstrel_sta_info *mi, struct ieee80211_local *local, | 
|  | struct minstrel_rate *d, struct ieee80211_rate *rate) | 
|  | { | 
|  | int erp = !!(rate->flags & IEEE80211_RATE_ERP_G); | 
|  |  | 
|  | d->perfect_tx_time = ieee80211_frame_duration(local, 1200, | 
|  | rate->bitrate, erp, 1); | 
|  | d->ack_time = ieee80211_frame_duration(local, 10, | 
|  | rate->bitrate, erp, 1); | 
|  | } | 
|  |  | 
|  | static void | 
|  | init_sample_table(struct minstrel_sta_info *mi) | 
|  | { | 
|  | unsigned int i, col, new_idx; | 
|  | unsigned int n_srates = mi->n_rates - 1; | 
|  | u8 rnd[8]; | 
|  |  | 
|  | mi->sample_column = 0; | 
|  | mi->sample_idx = 0; | 
|  | memset(mi->sample_table, 0, SAMPLE_COLUMNS * mi->n_rates); | 
|  |  | 
|  | for (col = 0; col < SAMPLE_COLUMNS; col++) { | 
|  | for (i = 0; i < n_srates; i++) { | 
|  | get_random_bytes(rnd, sizeof(rnd)); | 
|  | new_idx = (i + rnd[i & 7]) % n_srates; | 
|  |  | 
|  | while (SAMPLE_TBL(mi, new_idx, col) != 0) | 
|  | new_idx = (new_idx + 1) % n_srates; | 
|  |  | 
|  | /* Don't sample the slowest rate (i.e. slowest base | 
|  | * rate). We must presume that the slowest rate works | 
|  | * fine, or else other management frames will also be | 
|  | * failing and the link will break */ | 
|  | SAMPLE_TBL(mi, new_idx, col) = i + 1; | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static void | 
|  | minstrel_rate_init(void *priv, struct ieee80211_supported_band *sband, | 
|  | struct ieee80211_sta *sta, void *priv_sta) | 
|  | { | 
|  | struct minstrel_sta_info *mi = priv_sta; | 
|  | struct minstrel_priv *mp = priv; | 
|  | struct ieee80211_local *local = hw_to_local(mp->hw); | 
|  | struct ieee80211_rate *ctl_rate; | 
|  | unsigned int i, n = 0; | 
|  | unsigned int t_slot = 9; /* FIXME: get real slot time */ | 
|  |  | 
|  | mi->lowest_rix = rate_lowest_index(sband, sta); | 
|  | ctl_rate = &sband->bitrates[mi->lowest_rix]; | 
|  | mi->sp_ack_dur = ieee80211_frame_duration(local, 10, ctl_rate->bitrate, | 
|  | !!(ctl_rate->flags & IEEE80211_RATE_ERP_G), 1); | 
|  |  | 
|  | for (i = 0; i < sband->n_bitrates; i++) { | 
|  | struct minstrel_rate *mr = &mi->r[n]; | 
|  | unsigned int tx_time = 0, tx_time_cts = 0, tx_time_rtscts = 0; | 
|  | unsigned int tx_time_single; | 
|  | unsigned int cw = mp->cw_min; | 
|  |  | 
|  | if (!rate_supported(sta, sband->band, i)) | 
|  | continue; | 
|  | n++; | 
|  | memset(mr, 0, sizeof(*mr)); | 
|  |  | 
|  | mr->rix = i; | 
|  | mr->bitrate = sband->bitrates[i].bitrate / 5; | 
|  | calc_rate_durations(mi, local, mr, | 
|  | &sband->bitrates[i]); | 
|  |  | 
|  | /* calculate maximum number of retransmissions before | 
|  | * fallback (based on maximum segment size) */ | 
|  | mr->sample_limit = -1; | 
|  | mr->retry_count = 1; | 
|  | mr->retry_count_cts = 1; | 
|  | mr->retry_count_rtscts = 1; | 
|  | tx_time = mr->perfect_tx_time + mi->sp_ack_dur; | 
|  | do { | 
|  | /* add one retransmission */ | 
|  | tx_time_single = mr->ack_time + mr->perfect_tx_time; | 
|  |  | 
|  | /* contention window */ | 
|  | tx_time_single += t_slot + min(cw, mp->cw_max); | 
|  | cw = (cw + 1) << 1; | 
|  |  | 
|  | tx_time += tx_time_single; | 
|  | tx_time_cts += tx_time_single + mi->sp_ack_dur; | 
|  | tx_time_rtscts += tx_time_single + 2 * mi->sp_ack_dur; | 
|  | if ((tx_time_cts < mp->segment_size) && | 
|  | (mr->retry_count_cts < mp->max_retry)) | 
|  | mr->retry_count_cts++; | 
|  | if ((tx_time_rtscts < mp->segment_size) && | 
|  | (mr->retry_count_rtscts < mp->max_retry)) | 
|  | mr->retry_count_rtscts++; | 
|  | } while ((tx_time < mp->segment_size) && | 
|  | (++mr->retry_count < mp->max_retry)); | 
|  | mr->adjusted_retry_count = mr->retry_count; | 
|  | } | 
|  |  | 
|  | for (i = n; i < sband->n_bitrates; i++) { | 
|  | struct minstrel_rate *mr = &mi->r[i]; | 
|  | mr->rix = -1; | 
|  | } | 
|  |  | 
|  | mi->n_rates = n; | 
|  | mi->stats_update = jiffies; | 
|  |  | 
|  | init_sample_table(mi); | 
|  | } | 
|  |  | 
|  | static void * | 
|  | minstrel_alloc_sta(void *priv, struct ieee80211_sta *sta, gfp_t gfp) | 
|  | { | 
|  | struct ieee80211_supported_band *sband; | 
|  | struct minstrel_sta_info *mi; | 
|  | struct minstrel_priv *mp = priv; | 
|  | struct ieee80211_hw *hw = mp->hw; | 
|  | int max_rates = 0; | 
|  | int i; | 
|  |  | 
|  | mi = kzalloc(sizeof(struct minstrel_sta_info), gfp); | 
|  | if (!mi) | 
|  | return NULL; | 
|  |  | 
|  | for (i = 0; i < IEEE80211_NUM_BANDS; i++) { | 
|  | sband = hw->wiphy->bands[hw->conf.channel->band]; | 
|  | if (sband->n_bitrates > max_rates) | 
|  | max_rates = sband->n_bitrates; | 
|  | } | 
|  |  | 
|  | mi->r = kzalloc(sizeof(struct minstrel_rate) * max_rates, gfp); | 
|  | if (!mi->r) | 
|  | goto error; | 
|  |  | 
|  | mi->sample_table = kmalloc(SAMPLE_COLUMNS * max_rates, gfp); | 
|  | if (!mi->sample_table) | 
|  | goto error1; | 
|  |  | 
|  | mi->stats_update = jiffies; | 
|  | return mi; | 
|  |  | 
|  | error1: | 
|  | kfree(mi->r); | 
|  | error: | 
|  | kfree(mi); | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | static void | 
|  | minstrel_free_sta(void *priv, struct ieee80211_sta *sta, void *priv_sta) | 
|  | { | 
|  | struct minstrel_sta_info *mi = priv_sta; | 
|  |  | 
|  | kfree(mi->sample_table); | 
|  | kfree(mi->r); | 
|  | kfree(mi); | 
|  | } | 
|  |  | 
|  | static void * | 
|  | minstrel_alloc(struct ieee80211_hw *hw, struct dentry *debugfsdir) | 
|  | { | 
|  | struct minstrel_priv *mp; | 
|  |  | 
|  | mp = kzalloc(sizeof(struct minstrel_priv), GFP_ATOMIC); | 
|  | if (!mp) | 
|  | return NULL; | 
|  |  | 
|  | /* contention window settings | 
|  | * Just an approximation. Using the per-queue values would complicate | 
|  | * the calculations and is probably unnecessary */ | 
|  | mp->cw_min = 15; | 
|  | mp->cw_max = 1023; | 
|  |  | 
|  | /* number of packets (in %) to use for sampling other rates | 
|  | * sample less often for non-mrr packets, because the overhead | 
|  | * is much higher than with mrr */ | 
|  | mp->lookaround_rate = 5; | 
|  | mp->lookaround_rate_mrr = 10; | 
|  |  | 
|  | /* moving average weight for EWMA */ | 
|  | mp->ewma_level = 75; | 
|  |  | 
|  | /* maximum time that the hw is allowed to stay in one MRR segment */ | 
|  | mp->segment_size = 6000; | 
|  |  | 
|  | if (hw->max_rate_tries > 0) | 
|  | mp->max_retry = hw->max_rate_tries; | 
|  | else | 
|  | /* safe default, does not necessarily have to match hw properties */ | 
|  | mp->max_retry = 7; | 
|  |  | 
|  | if (hw->max_rates >= 4) | 
|  | mp->has_mrr = true; | 
|  |  | 
|  | mp->hw = hw; | 
|  | mp->update_interval = 100; | 
|  |  | 
|  | return mp; | 
|  | } | 
|  |  | 
|  | static void | 
|  | minstrel_free(void *priv) | 
|  | { | 
|  | kfree(priv); | 
|  | } | 
|  |  | 
|  | static struct rate_control_ops mac80211_minstrel = { | 
|  | .name = "minstrel", | 
|  | .tx_status = minstrel_tx_status, | 
|  | .get_rate = minstrel_get_rate, | 
|  | .rate_init = minstrel_rate_init, | 
|  | .alloc = minstrel_alloc, | 
|  | .free = minstrel_free, | 
|  | .alloc_sta = minstrel_alloc_sta, | 
|  | .free_sta = minstrel_free_sta, | 
|  | #ifdef CONFIG_MAC80211_DEBUGFS | 
|  | .add_sta_debugfs = minstrel_add_sta_debugfs, | 
|  | .remove_sta_debugfs = minstrel_remove_sta_debugfs, | 
|  | #endif | 
|  | }; | 
|  |  | 
|  | int __init | 
|  | rc80211_minstrel_init(void) | 
|  | { | 
|  | return ieee80211_rate_control_register(&mac80211_minstrel); | 
|  | } | 
|  |  | 
|  | void | 
|  | rc80211_minstrel_exit(void) | 
|  | { | 
|  | ieee80211_rate_control_unregister(&mac80211_minstrel); | 
|  | } | 
|  |  |