diff --git a/drivers/ide/pci/aec62xx.c b/drivers/ide/pci/aec62xx.c
index 2532999..f6dc6c2 100644
--- a/drivers/ide/pci/aec62xx.c
+++ b/drivers/ide/pci/aec62xx.c
@@ -13,6 +13,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "aec62xx"
+
 struct chipset_bus_clock_list_entry {
 	u8 xfer_speed;
 	u8 chipset_settings;
@@ -180,8 +182,8 @@
 };
 
 static const struct ide_port_info aec62xx_chipsets[] __devinitdata = {
-	{	/* 0 */
-		.name		= "AEC6210",
+	{	/* 0: AEC6210 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_aec62xx,
 		.enablebits	= {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
 		.port_ops	= &atp850_port_ops,
@@ -192,8 +194,9 @@
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= ATA_UDMA2,
-	},{	/* 1 */
-		.name		= "AEC6260",
+	},
+	{	/* 1: AEC6260 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_aec62xx,
 		.port_ops	= &atp86x_port_ops,
 		.host_flags	= IDE_HFLAG_NO_ATAPI_DMA | IDE_HFLAG_NO_AUTODMA |
@@ -201,8 +204,9 @@
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= ATA_UDMA4,
-	},{	/* 2 */
-		.name		= "AEC6260R",
+	},
+	{	/* 2: AEC6260R */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_aec62xx,
 		.enablebits	= {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
 		.port_ops	= &atp86x_port_ops,
@@ -211,8 +215,9 @@
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= ATA_UDMA4,
-	},{	/* 3 */
-		.name		= "AEC6280",
+	},
+	{	/* 3: AEC6280 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_aec62xx,
 		.port_ops	= &atp86x_port_ops,
 		.host_flags	= IDE_HFLAG_NO_ATAPI_DMA |
@@ -220,8 +225,9 @@
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= ATA_UDMA5,
-	},{	/* 4 */
-		.name		= "AEC6280R",
+	},
+	{	/* 4: AEC6280R */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_aec62xx,
 		.enablebits	= {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
 		.port_ops	= &atp86x_port_ops,
@@ -268,7 +274,8 @@
 		unsigned long dma_base = pci_resource_start(dev, 4);
 
 		if (inb(dma_base + 2) & 0x10) {
-			d.name = (idx == 4) ? "AEC6880R" : "AEC6880";
+			printk(KERN_INFO DRV_NAME " %s: AEC6880%s card detected"
+				"\n", pci_name(dev), (idx == 4) ? "R" : "");
 			d.udma_mask = ATA_UDMA6;
 		}
 	}
diff --git a/drivers/ide/pci/alim15x3.c b/drivers/ide/pci/alim15x3.c
index ac17150..a099c4d 100644
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -38,6 +38,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "alim15x3"
+
 /*
  * Allow UDMA on M1543C-E chipset for WDC disks that ignore CRC checking
  * (this is DANGEROUS and could result in data corruption).
@@ -515,7 +517,7 @@
 };
 
 static const struct ide_port_info ali15x3_chipset __devinitdata = {
-	.name		= "ALI15X3",
+	.name		= DRV_NAME,
 	.init_chipset	= init_chipset_ali15x3,
 	.init_hwif	= init_hwif_ali15x3,
 	.init_dma	= init_dma_ali15x3,
diff --git a/drivers/ide/pci/amd74xx.c b/drivers/ide/pci/amd74xx.c
index 2b118f8..cbf78ed 100644
--- a/drivers/ide/pci/amd74xx.c
+++ b/drivers/ide/pci/amd74xx.c
@@ -21,6 +21,8 @@
 #include <linux/init.h>
 #include <linux/ide.h>
 
+#define DRV_NAME "amd74xx"
+
 enum {
 	AMD_IDE_CONFIG		= 0x41,
 	AMD_CABLE_DETECT	= 0x42,
@@ -204,9 +206,9 @@
 	 IDE_HFLAG_IO_32BIT | \
 	 IDE_HFLAG_UNMASK_IRQS)
 
-#define DECLARE_AMD_DEV(name_str, swdma, udma)				\
+#define DECLARE_AMD_DEV(swdma, udma)				\
 	{								\
-		.name		= name_str,				\
+		.name		= DRV_NAME,				\
 		.init_chipset	= init_chipset_amd74xx,			\
 		.init_hwif	= init_hwif_amd74xx,			\
 		.enablebits	= {{0x40,0x02,0x02}, {0x40,0x01,0x01}},	\
@@ -218,9 +220,9 @@
 		.udma_mask	= udma,					\
 	}
 
-#define DECLARE_NV_DEV(name_str, udma)					\
+#define DECLARE_NV_DEV(udma)					\
 	{								\
-		.name		= name_str,				\
+		.name		= DRV_NAME,				\
 		.init_chipset	= init_chipset_amd74xx,			\
 		.init_hwif	= init_hwif_amd74xx,			\
 		.enablebits	= {{0x50,0x02,0x02}, {0x50,0x01,0x01}},	\
@@ -233,31 +235,15 @@
 	}
 
 static const struct ide_port_info amd74xx_chipsets[] __devinitdata = {
-	/*  0 */ DECLARE_AMD_DEV("AMD7401",	  0x00, ATA_UDMA2),
-	/*  1 */ DECLARE_AMD_DEV("AMD7409", ATA_SWDMA2, ATA_UDMA4),
-	/*  2 */ DECLARE_AMD_DEV("AMD7411", ATA_SWDMA2, ATA_UDMA5),
-	/*  3 */ DECLARE_AMD_DEV("AMD7441", ATA_SWDMA2, ATA_UDMA5),
-	/*  4 */ DECLARE_AMD_DEV("AMD8111", ATA_SWDMA2, ATA_UDMA6),
+	/* 0: AMD7401 */	DECLARE_AMD_DEV(0x00, ATA_UDMA2),
+	/* 1: AMD7409 */	DECLARE_AMD_DEV(ATA_SWDMA2, ATA_UDMA4),
+	/* 2: AMD7411/7441 */	DECLARE_AMD_DEV(ATA_SWDMA2, ATA_UDMA5),
+	/* 3: AMD8111 */	DECLARE_AMD_DEV(ATA_SWDMA2, ATA_UDMA6),
 
-	/*  5 */ DECLARE_NV_DEV("NFORCE",		ATA_UDMA5),
-	/*  6 */ DECLARE_NV_DEV("NFORCE2",		ATA_UDMA6),
-	/*  7 */ DECLARE_NV_DEV("NFORCE2-U400R",	ATA_UDMA6),
-	/*  8 */ DECLARE_NV_DEV("NFORCE2-U400R-SATA",	ATA_UDMA6),
-	/*  9 */ DECLARE_NV_DEV("NFORCE3-150",		ATA_UDMA6),
-	/* 10 */ DECLARE_NV_DEV("NFORCE3-250",		ATA_UDMA6),
-	/* 11 */ DECLARE_NV_DEV("NFORCE3-250-SATA",	ATA_UDMA6),
-	/* 12 */ DECLARE_NV_DEV("NFORCE3-250-SATA2",	ATA_UDMA6),
-	/* 13 */ DECLARE_NV_DEV("NFORCE-CK804",		ATA_UDMA6),
-	/* 14 */ DECLARE_NV_DEV("NFORCE-MCP04",		ATA_UDMA6),
-	/* 15 */ DECLARE_NV_DEV("NFORCE-MCP51",		ATA_UDMA6),
-	/* 16 */ DECLARE_NV_DEV("NFORCE-MCP55",		ATA_UDMA6),
-	/* 17 */ DECLARE_NV_DEV("NFORCE-MCP61",		ATA_UDMA6),
-	/* 18 */ DECLARE_NV_DEV("NFORCE-MCP65",		ATA_UDMA6),
-	/* 19 */ DECLARE_NV_DEV("NFORCE-MCP67",		ATA_UDMA6),
-	/* 20 */ DECLARE_NV_DEV("NFORCE-MCP73",		ATA_UDMA6),
-	/* 21 */ DECLARE_NV_DEV("NFORCE-MCP77",		ATA_UDMA6),
+	/* 4: NFORCE */		DECLARE_NV_DEV(ATA_UDMA5),
+	/* 5: >= NFORCE2 */	DECLARE_NV_DEV(ATA_UDMA6),
 
-	/* 22 */ DECLARE_AMD_DEV("AMD5536", ATA_SWDMA2, ATA_UDMA5),
+	/* 6: AMD5536 */	DECLARE_AMD_DEV(ATA_SWDMA2, ATA_UDMA5),
 };
 
 static int __devinit amd74xx_probe(struct pci_dev *dev, const struct pci_device_id *id)
@@ -274,7 +260,7 @@
 		if (dev->revision <= 7)
 			d.swdma_mask = 0;
 		d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
-	} else if (idx == 4) {
+	} else if (idx == 3) {
 		if (dev->subsystem_vendor == PCI_VENDOR_ID_AMD &&
 		    dev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE)
 			d.udma_mask = ATA_UDMA5;
@@ -308,30 +294,30 @@
 	{ PCI_VDEVICE(AMD,	PCI_DEVICE_ID_AMD_COBRA_7401),		 0 },
 	{ PCI_VDEVICE(AMD,	PCI_DEVICE_ID_AMD_VIPER_7409),		 1 },
 	{ PCI_VDEVICE(AMD,	PCI_DEVICE_ID_AMD_VIPER_7411),		 2 },
-	{ PCI_VDEVICE(AMD,	PCI_DEVICE_ID_AMD_OPUS_7441),		 3 },
-	{ PCI_VDEVICE(AMD,	PCI_DEVICE_ID_AMD_8111_IDE),		 4 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_IDE),	 5 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE),	 6 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE),	 7 },
+	{ PCI_VDEVICE(AMD,	PCI_DEVICE_ID_AMD_OPUS_7441),		 2 },
+	{ PCI_VDEVICE(AMD,	PCI_DEVICE_ID_AMD_8111_IDE),		 3 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_IDE),	 4 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE),	 5 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE),	 5 },
 #ifdef CONFIG_BLK_DEV_IDE_SATA
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA),	 8 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA),	 5 },
 #endif
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE),	 9 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE),	10 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE),	 5 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE),	 5 },
 #ifdef CONFIG_BLK_DEV_IDE_SATA
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA),	11 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2),	12 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA),	 5 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2),	 5 },
 #endif
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE),	13 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE),	14 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE),	15 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE),	16 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE),	17 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP65_IDE),	18 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP67_IDE),	19 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP73_IDE),	20 },
-	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP77_IDE),	21 },
-	{ PCI_VDEVICE(AMD,	PCI_DEVICE_ID_AMD_CS5536_IDE),		22 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE),	 5 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE),	 5 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE),	 5 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE),	 5 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE),	 5 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP65_IDE),	 5 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP67_IDE),	 5 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP73_IDE),	 5 },
+	{ PCI_VDEVICE(NVIDIA,	PCI_DEVICE_ID_NVIDIA_NFORCE_MCP77_IDE),	 5 },
+	{ PCI_VDEVICE(AMD,	PCI_DEVICE_ID_AMD_CS5536_IDE),		 6 },
 	{ 0, },
 };
 MODULE_DEVICE_TABLE(pci, amd74xx_pci_tbl);
diff --git a/drivers/ide/pci/atiixp.c b/drivers/ide/pci/atiixp.c
index 4c49c1b..332f08f 100644
--- a/drivers/ide/pci/atiixp.c
+++ b/drivers/ide/pci/atiixp.c
@@ -11,6 +11,8 @@
 #include <linux/ide.h>
 #include <linux/init.h>
 
+#define DRV_NAME "atiixp"
+
 #define ATIIXP_IDE_PIO_TIMING		0x40
 #define ATIIXP_IDE_MDMA_TIMING		0x44
 #define ATIIXP_IDE_PIO_CONTROL		0x48
@@ -137,16 +139,17 @@
 };
 
 static const struct ide_port_info atiixp_pci_info[] __devinitdata = {
-	{	/* 0 */
-		.name		= "ATIIXP",
+	{	/* 0: IXP200/300/400/700 */
+		.name		= DRV_NAME,
 		.enablebits	= {{0x48,0x01,0x00}, {0x48,0x08,0x00}},
 		.port_ops	= &atiixp_port_ops,
 		.host_flags	= IDE_HFLAG_LEGACY_IRQS,
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= ATA_UDMA5,
-	},{	/* 1 */
-		.name		= "SB600_PATA",
+	},
+	{	/* 1: IXP600 */
+		.name		= DRV_NAME,
 		.enablebits	= {{0x48,0x01,0x00}, {0x00,0x00,0x00}},
 		.port_ops	= &atiixp_port_ops,
 		.host_flags	= IDE_HFLAG_SINGLE | IDE_HFLAG_LEGACY_IRQS,
diff --git a/drivers/ide/pci/cmd64x.c b/drivers/ide/pci/cmd64x.c
index 0a4d194..3d84deb 100644
--- a/drivers/ide/pci/cmd64x.c
+++ b/drivers/ide/pci/cmd64x.c
@@ -19,6 +19,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "cmd64x"
+
 #define CMD_DEBUG 0
 
 #if CMD_DEBUG
@@ -407,8 +409,8 @@
 };
 
 static const struct ide_port_info cmd64x_chipsets[] __devinitdata = {
-	{	/* 0 */
-		.name		= "CMD643",
+	{	/* 0: CMD643 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_cmd64x,
 		.enablebits	= {{0x00,0x00,0x00}, {0x51,0x08,0x08}},
 		.port_ops	= &cmd64x_port_ops,
@@ -418,8 +420,9 @@
 		.pio_mask	= ATA_PIO5,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= 0x00, /* no udma */
-	},{	/* 1 */
-		.name		= "CMD646",
+	},
+	{	/* 1: CMD646 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_cmd64x,
 		.enablebits	= {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
 		.chipset	= ide_cmd646,
@@ -429,8 +432,9 @@
 		.pio_mask	= ATA_PIO5,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= ATA_UDMA2,
-	},{	/* 2 */
-		.name		= "CMD648",
+	},
+	{	/* 2: CMD648 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_cmd64x,
 		.enablebits	= {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
 		.port_ops	= &cmd64x_port_ops,
@@ -439,8 +443,9 @@
 		.pio_mask	= ATA_PIO5,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= ATA_UDMA4,
-	},{	/* 3 */
-		.name		= "CMD649",
+	},
+	{	/* 3: CMD649 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_cmd64x,
 		.enablebits	= {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
 		.port_ops	= &cmd64x_port_ops,
diff --git a/drivers/ide/pci/cs5520.c b/drivers/ide/pci/cs5520.c
index b03d8ae..c0364b2 100644
--- a/drivers/ide/pci/cs5520.c
+++ b/drivers/ide/pci/cs5520.c
@@ -41,6 +41,8 @@
 #include <linux/ide.h>
 #include <linux/dma-mapping.h>
 
+#define DRV_NAME "cs5520"
+
 struct pio_clocks
 {
 	int address;
@@ -92,18 +94,11 @@
 	.set_dma_mode		= cs5520_set_dma_mode,
 };
 
-#define DECLARE_CS_DEV(name_str)				\
-	{							\
-		.name		= name_str,			\
-		.port_ops	= &cs5520_port_ops,		\
-		.host_flags	= IDE_HFLAG_ISA_PORTS |		\
-				  IDE_HFLAG_CS5520,		\
-		.pio_mask	= ATA_PIO4,			\
-	}
-
-static const struct ide_port_info cyrix_chipsets[] __devinitdata = {
-	/* 0 */ DECLARE_CS_DEV("Cyrix 5510"),
-	/* 1 */ DECLARE_CS_DEV("Cyrix 5520")
+static const struct ide_port_info cyrix_chipset __devinitdata = {
+	.name		= DRV_NAME,
+	.port_ops	= &cs5520_port_ops,
+	.host_flags	= IDE_HFLAG_ISA_PORTS | IDE_HFLAG_CS5520,
+	.pio_mask	= ATA_PIO4,
 };
 
 /*
@@ -114,7 +109,7 @@
  
 static int __devinit cs5520_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 {
-	const struct ide_port_info *d = &cyrix_chipsets[id->driver_data];
+	const struct ide_port_info *d = &cyrix_chipset;
 	hw_regs_t hw[4], *hws[] = { NULL, NULL, NULL, NULL };
 
 	ide_setup_pci_noise(dev, d);
@@ -128,7 +123,8 @@
 	}
 	pci_set_master(dev);
 	if (pci_set_dma_mask(dev, DMA_32BIT_MASK)) {
-		printk(KERN_WARNING "cs5520: No suitable DMA available.\n");
+		printk(KERN_WARNING "%s: No suitable DMA available.\n",
+			d->name);
 		return -ENODEV;
 	}
 
diff --git a/drivers/ide/pci/cs5530.c b/drivers/ide/pci/cs5530.c
index dff345c..5543c86 100644
--- a/drivers/ide/pci/cs5530.c
+++ b/drivers/ide/pci/cs5530.c
@@ -22,6 +22,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "cs5530"
+
 /*
  * Here are the standard PIO mode 0-4 timings for each "format".
  * Format-0 uses fast data reg timings, with slower command reg timings.
@@ -243,7 +245,7 @@
 };
 
 static const struct ide_port_info cs5530_chipset __devinitdata = {
-	.name		= "CS5530",
+	.name		= DRV_NAME,
 	.init_chipset	= init_chipset_cs5530,
 	.init_hwif	= init_hwif_cs5530,
 	.port_ops	= &cs5530_port_ops,
diff --git a/drivers/ide/pci/cs5535.c b/drivers/ide/pci/cs5535.c
index a730013..f7b50cd 100644
--- a/drivers/ide/pci/cs5535.c
+++ b/drivers/ide/pci/cs5535.c
@@ -26,6 +26,8 @@
 #include <linux/pci.h>
 #include <linux/ide.h>
 
+#define DRV_NAME "cs5535"
+
 #define MSR_ATAC_BASE		0x51300000
 #define ATAC_GLD_MSR_CAP	(MSR_ATAC_BASE+0)
 #define ATAC_GLD_MSR_CONFIG	(MSR_ATAC_BASE+0x01)
@@ -169,7 +171,7 @@
 };
 
 static const struct ide_port_info cs5535_chipset __devinitdata = {
-	.name		= "CS5535",
+	.name		= DRV_NAME,
 	.port_ops	= &cs5535_port_ops,
 	.host_flags	= IDE_HFLAG_SINGLE | IDE_HFLAG_POST_SET_MODE,
 	.pio_mask	= ATA_PIO4,
diff --git a/drivers/ide/pci/cy82c693.c b/drivers/ide/pci/cy82c693.c
index 04f2688..41c7f33 100644
--- a/drivers/ide/pci/cy82c693.c
+++ b/drivers/ide/pci/cy82c693.c
@@ -48,6 +48,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "cy82c693"
+
 /* the current version */
 #define CY82_VERSION	"CY82C693U driver v0.34 99-13-12 Andreas S. Krebs (akrebs@altavista.net)"
 
@@ -398,7 +400,7 @@
 };
 
 static const struct ide_port_info cy82c693_chipset __devinitdata = {
-	.name		= "CY82C693",
+	.name		= DRV_NAME,
 	.init_chipset	= init_chipset_cy82c693,
 	.init_iops	= init_iops_cy82c693,
 	.port_ops	= &cy82c693_port_ops,
diff --git a/drivers/ide/pci/generic.c b/drivers/ide/pci/generic.c
index e034e21..b07d4f4 100644
--- a/drivers/ide/pci/generic.c
+++ b/drivers/ide/pci/generic.c
@@ -27,6 +27,8 @@
 #include <linux/ide.h>
 #include <linux/init.h>
 
+#define DRV_NAME "ide_pci_generic"
+
 static int ide_generic_all;		/* Set to claim all devices */
 
 module_param_named(all_generic_ide, ide_generic_all, bool, 0444);
@@ -34,9 +36,9 @@
 
 #define IDE_HFLAGS_UMC (IDE_HFLAG_NO_DMA | IDE_HFLAG_FORCE_LEGACY_IRQS)
 
-#define DECLARE_GENERIC_PCI_DEV(name_str, extra_flags) \
+#define DECLARE_GENERIC_PCI_DEV(extra_flags) \
 	{ \
-		.name		= name_str, \
+		.name		= DRV_NAME, \
 		.host_flags	= IDE_HFLAG_TRUST_BIOS_FOR_DMA | \
 				  extra_flags, \
 		.swdma_mask	= ATA_SWDMA2, \
@@ -45,10 +47,11 @@
 	}
 
 static const struct ide_port_info generic_chipsets[] __devinitdata = {
-	/*  0 */ DECLARE_GENERIC_PCI_DEV("Unknown",	0),
+	/*  0: Unknown */
+	DECLARE_GENERIC_PCI_DEV(0),
 
-	{	/* 1 */
-		.name		= "NS87410",
+	{	/* 1: NS87410 */
+		.name		= DRV_NAME,
 		.enablebits	= { {0x43, 0x08, 0x08}, {0x47, 0x08, 0x08} },
 		.host_flags	= IDE_HFLAG_TRUST_BIOS_FOR_DMA,
 		.swdma_mask	= ATA_SWDMA2,
@@ -56,17 +59,15 @@
 		.udma_mask	= ATA_UDMA6,
 	},
 
-	/*  2 */ DECLARE_GENERIC_PCI_DEV("SAMURAI",	0),
-	/*  3 */ DECLARE_GENERIC_PCI_DEV("HT6565",	0),
-	/*  4 */ DECLARE_GENERIC_PCI_DEV("UM8673F",	IDE_HFLAGS_UMC),
-	/*  5 */ DECLARE_GENERIC_PCI_DEV("UM8886A",	IDE_HFLAGS_UMC),
-	/*  6 */ DECLARE_GENERIC_PCI_DEV("UM8886BF",	IDE_HFLAGS_UMC),
-	/*  7 */ DECLARE_GENERIC_PCI_DEV("HINT_IDE",	0),
-	/*  8 */ DECLARE_GENERIC_PCI_DEV("VIA_IDE",	IDE_HFLAG_NO_AUTODMA),
-	/*  9 */ DECLARE_GENERIC_PCI_DEV("OPTI621V",	IDE_HFLAG_NO_AUTODMA),
+	/*  2: SAMURAI / HT6565 / HINT_IDE */
+	DECLARE_GENERIC_PCI_DEV(0),
+	/*  3: UM8673F / UM8886A / UM8886BF */
+	DECLARE_GENERIC_PCI_DEV(IDE_HFLAGS_UMC),
+	/*  4: VIA_IDE / OPTI621V / Piccolo010{2,3,5} */
+	DECLARE_GENERIC_PCI_DEV(IDE_HFLAG_NO_AUTODMA),
 
-	{	/* 10 */
-		.name		= "VIA8237SATA",
+	{	/* 5: VIA8237SATA */
+		.name		= DRV_NAME,
 		.host_flags	= IDE_HFLAG_TRUST_BIOS_FOR_DMA |
 				  IDE_HFLAG_OFF_BOARD,
 		.swdma_mask	= ATA_SWDMA2,
@@ -74,12 +75,8 @@
 		.udma_mask	= ATA_UDMA6,
 	},
 
-	/* 11 */ DECLARE_GENERIC_PCI_DEV("Piccolo0102",	IDE_HFLAG_NO_AUTODMA),
-	/* 12 */ DECLARE_GENERIC_PCI_DEV("Piccolo0103",	IDE_HFLAG_NO_AUTODMA),
-	/* 13 */ DECLARE_GENERIC_PCI_DEV("Piccolo0105",	IDE_HFLAG_NO_AUTODMA),
-
-	{	/* 14 */
-		.name		= "Revolution",
+	{	/* 6: Revolution */
+		.name		= DRV_NAME,
 		.host_flags	= IDE_HFLAG_CLEAR_SIMPLEX |
 				  IDE_HFLAG_TRUST_BIOS_FOR_DMA |
 				  IDE_HFLAG_OFF_BOARD,
@@ -147,20 +144,20 @@
 static const struct pci_device_id generic_pci_tbl[] = {
 	{ PCI_VDEVICE(NS,	PCI_DEVICE_ID_NS_87410),		 1 },
 	{ PCI_VDEVICE(PCTECH,	PCI_DEVICE_ID_PCTECH_SAMURAI_IDE),	 2 },
-	{ PCI_VDEVICE(HOLTEK,	PCI_DEVICE_ID_HOLTEK_6565),		 3 },
-	{ PCI_VDEVICE(UMC,	PCI_DEVICE_ID_UMC_UM8673F),		 4 },
-	{ PCI_VDEVICE(UMC,	PCI_DEVICE_ID_UMC_UM8886A),		 5 },
-	{ PCI_VDEVICE(UMC,	PCI_DEVICE_ID_UMC_UM8886BF),		 6 },
-	{ PCI_VDEVICE(HINT,	PCI_DEVICE_ID_HINT_VXPROII_IDE),	 7 },
-	{ PCI_VDEVICE(VIA,	PCI_DEVICE_ID_VIA_82C561),		 8 },
-	{ PCI_VDEVICE(OPTI,	PCI_DEVICE_ID_OPTI_82C558),		 9 },
+	{ PCI_VDEVICE(HOLTEK,	PCI_DEVICE_ID_HOLTEK_6565),		 2 },
+	{ PCI_VDEVICE(UMC,	PCI_DEVICE_ID_UMC_UM8673F),		 3 },
+	{ PCI_VDEVICE(UMC,	PCI_DEVICE_ID_UMC_UM8886A),		 3 },
+	{ PCI_VDEVICE(UMC,	PCI_DEVICE_ID_UMC_UM8886BF),		 3 },
+	{ PCI_VDEVICE(HINT,	PCI_DEVICE_ID_HINT_VXPROII_IDE),	 2 },
+	{ PCI_VDEVICE(VIA,	PCI_DEVICE_ID_VIA_82C561),		 4 },
+	{ PCI_VDEVICE(OPTI,	PCI_DEVICE_ID_OPTI_82C558),		 4 },
 #ifdef CONFIG_BLK_DEV_IDE_SATA
-	{ PCI_VDEVICE(VIA,	PCI_DEVICE_ID_VIA_8237_SATA),		10 },
+	{ PCI_VDEVICE(VIA,	PCI_DEVICE_ID_VIA_8237_SATA),		 5 },
 #endif
-	{ PCI_VDEVICE(TOSHIBA,	PCI_DEVICE_ID_TOSHIBA_PICCOLO),		11 },
-	{ PCI_VDEVICE(TOSHIBA,	PCI_DEVICE_ID_TOSHIBA_PICCOLO_1),	12 },
-	{ PCI_VDEVICE(TOSHIBA,	PCI_DEVICE_ID_TOSHIBA_PICCOLO_2),	13 },
-	{ PCI_VDEVICE(NETCELL,	PCI_DEVICE_ID_REVOLUTION),		14 },
+	{ PCI_VDEVICE(TOSHIBA,	PCI_DEVICE_ID_TOSHIBA_PICCOLO),		 4 },
+	{ PCI_VDEVICE(TOSHIBA,	PCI_DEVICE_ID_TOSHIBA_PICCOLO_1),	 4 },
+	{ PCI_VDEVICE(TOSHIBA,	PCI_DEVICE_ID_TOSHIBA_PICCOLO_2),	 4 },
+	{ PCI_VDEVICE(NETCELL,	PCI_DEVICE_ID_REVOLUTION),		 6 },
 	/*
 	 * Must come last.  If you add entries adjust
 	 * this table and generic_chipsets[] appropriately.
diff --git a/drivers/ide/pci/hpt34x.c b/drivers/ide/pci/hpt34x.c
index b52f833..baabb4c 100644
--- a/drivers/ide/pci/hpt34x.c
+++ b/drivers/ide/pci/hpt34x.c
@@ -33,6 +33,8 @@
 #include <linux/init.h>
 #include <linux/ide.h>
 
+#define DRV_NAME "hpt34x"
+
 #define HPT343_DEBUG_DRIVE_INFO		0
 
 static void hpt34x_set_mode(ide_drive_t *drive, const u8 speed)
@@ -126,15 +128,15 @@
 	 IDE_HFLAG_NO_AUTODMA)
 
 static const struct ide_port_info hpt34x_chipsets[] __devinitdata = {
-	{ /* 0 */
-		.name		= "HPT343",
+	{ /* 0: HPT343 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_hpt34x,
 		.port_ops	= &hpt34x_port_ops,
 		.host_flags	= IDE_HFLAGS_HPT34X | IDE_HFLAG_NON_BOOTABLE,
 		.pio_mask	= ATA_PIO5,
 	},
-	{ /* 1 */
-		.name		= "HPT345",
+	{ /* 1: HPT345 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_hpt34x,
 		.port_ops	= &hpt34x_port_ops,
 		.host_flags	= IDE_HFLAGS_HPT34X | IDE_HFLAG_OFF_BOARD,
diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c
index b8004c3..6a1c65c 100644
--- a/drivers/ide/pci/hpt366.c
+++ b/drivers/ide/pci/hpt366.c
@@ -131,6 +131,8 @@
 #include <asm/uaccess.h>
 #include <asm/io.h>
 
+#define DRV_NAME "hpt366"
+
 /* various tuning parameters */
 #define HPT_RESET_STATE_ENGINE
 #undef	HPT_DELAY_INTERRUPT
@@ -1362,7 +1364,7 @@
 	if (dev2->irq != dev->irq) {
 		/* FIXME: we need a core pci_set_interrupt() */
 		dev2->irq = dev->irq;
-		printk(KERN_INFO "HPT374 %s: PCI config space interrupt "
+		printk(KERN_INFO DRV_NAME " %s: PCI config space interrupt "
 			"fixed\n", pci_name(dev2));
 	}
 }
@@ -1398,7 +1400,7 @@
 	pci_read_config_byte(dev2, PCI_INTERRUPT_PIN, &pin2);
 
 	if (pin1 != pin2 && dev->irq == dev2->irq) {
-		printk(KERN_INFO "HPT36x %s: onboard version of chipset, "
+		printk(KERN_INFO DRV_NAME " %s: onboard version of chipset, "
 			"pin1=%d pin2=%d\n", pci_name(dev), pin1, pin2);
 		return 1;
 	}
@@ -1454,8 +1456,8 @@
 };
 
 static const struct ide_port_info hpt366_chipsets[] __devinitdata = {
-	{	/* 0 */
-		.name		= "HPT36x",
+	{	/* 0: HPT36x */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_hpt366,
 		.init_hwif	= init_hwif_hpt366,
 		.init_dma	= init_dma_hpt366,
@@ -1471,53 +1473,9 @@
 		.host_flags	= IDE_HFLAGS_HPT3XX | IDE_HFLAG_SINGLE,
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
-	},{	/* 1 */
-		.name		= "HPT372A",
-		.init_chipset	= init_chipset_hpt366,
-		.init_hwif	= init_hwif_hpt366,
-		.init_dma	= init_dma_hpt366,
-		.enablebits	= {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
-		.port_ops	= &hpt3xx_port_ops,
-		.dma_ops	= &hpt37x_dma_ops,
-		.host_flags	= IDE_HFLAGS_HPT3XX,
-		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
-	},{	/* 2 */
-		.name		= "HPT302",
-		.init_chipset	= init_chipset_hpt366,
-		.init_hwif	= init_hwif_hpt366,
-		.init_dma	= init_dma_hpt366,
-		.enablebits	= {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
-		.port_ops	= &hpt3xx_port_ops,
-		.dma_ops	= &hpt37x_dma_ops,
-		.host_flags	= IDE_HFLAGS_HPT3XX,
-		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
-	},{	/* 3 */
-		.name		= "HPT371",
-		.init_chipset	= init_chipset_hpt366,
-		.init_hwif	= init_hwif_hpt366,
-		.init_dma	= init_dma_hpt366,
-		.enablebits	= {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
-		.port_ops	= &hpt3xx_port_ops,
-		.dma_ops	= &hpt37x_dma_ops,
-		.host_flags	= IDE_HFLAGS_HPT3XX,
-		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
-	},{	/* 4 */
-		.name		= "HPT374",
-		.init_chipset	= init_chipset_hpt366,
-		.init_hwif	= init_hwif_hpt366,
-		.init_dma	= init_dma_hpt366,
-		.enablebits	= {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
-		.udma_mask	= ATA_UDMA5,
-		.port_ops	= &hpt3xx_port_ops,
-		.dma_ops	= &hpt37x_dma_ops,
-		.host_flags	= IDE_HFLAGS_HPT3XX,
-		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
-	},{	/* 5 */
-		.name		= "HPT372N",
+	},
+	{	/* 1: HPT3xx */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_hpt366,
 		.init_hwif	= init_hwif_hpt366,
 		.init_dma	= init_dma_hpt366,
@@ -1583,9 +1541,10 @@
 		break;
 	}
 
-	d = hpt366_chipsets[idx];
+	printk(KERN_INFO DRV_NAME ": %s chipset detected\n", info->chip_name);
 
-	d.name = info->chip_name;
+	d = hpt366_chipsets[min_t(u8, idx, 1)];
+
 	d.udma_mask = info->udma_mask;
 
 	/* fixup ->dma_ops for HPT370/HPT370A */
diff --git a/drivers/ide/pci/it8213.c b/drivers/ide/pci/it8213.c
index 451b87f..6eba8f1 100644
--- a/drivers/ide/pci/it8213.c
+++ b/drivers/ide/pci/it8213.c
@@ -14,6 +14,8 @@
 #include <linux/ide.h>
 #include <linux/init.h>
 
+#define DRV_NAME "it8213"
+
 /**
  *	it8213_set_pio_mode	-	set host controller for PIO mode
  *	@drive: drive
@@ -156,7 +158,7 @@
 };
 
 static const struct ide_port_info it8213_chipset __devinitdata = {
-	.name		= "IT8213",
+	.name		= DRV_NAME,
 	.enablebits	= { {0x41, 0x80, 0x80} },
 	.port_ops	= &it8213_port_ops,
 	.host_flags	= IDE_HFLAG_SINGLE,
diff --git a/drivers/ide/pci/it821x.c b/drivers/ide/pci/it821x.c
index a3d8959..7417335 100644
--- a/drivers/ide/pci/it821x.c
+++ b/drivers/ide/pci/it821x.c
@@ -67,6 +67,8 @@
 #include <linux/ide.h>
 #include <linux/init.h>
 
+#define DRV_NAME "it821x"
+
 struct it821x_dev
 {
 	unsigned int smart:1,		/* Are we in smart raid mode */
@@ -569,7 +571,7 @@
 		idev->timing10 = 1;
 		hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
 		if (idev->smart == 0)
-			printk(KERN_WARNING "it821x %s: revision 0x10, "
+			printk(KERN_WARNING DRV_NAME " %s: revision 0x10, "
 				"workarounds activated\n", pci_name(dev));
 	}
 
@@ -610,12 +612,12 @@
 
 	/* Force the card into bypass mode if so requested */
 	if (it8212_noraid) {
-		printk(KERN_INFO "it821x %s: forcing bypass mode\n",
+		printk(KERN_INFO DRV_NAME " %s: forcing bypass mode\n",
 			pci_name(dev));
 		it8212_disable_raid(dev);
 	}
 	pci_read_config_byte(dev, 0x50, &conf);
-	printk(KERN_INFO "it821x %s: controller in %s mode\n",
+	printk(KERN_INFO DRV_NAME " %s: controller in %s mode\n",
 		pci_name(dev), mode[conf & 1]);
 	return 0;
 }
@@ -629,7 +631,7 @@
 };
 
 static const struct ide_port_info it821x_chipset __devinitdata = {
-	.name		= "IT821X",
+	.name		= DRV_NAME,
 	.init_chipset	= init_chipset_it821x,
 	.init_hwif	= init_hwif_it821x,
 	.port_ops	= &it821x_port_ops,
@@ -652,7 +654,7 @@
 
 	itdevs = kzalloc(2 * sizeof(*itdevs), GFP_KERNEL);
 	if (itdevs == NULL) {
-		printk(KERN_ERR "it821x %s: out of memory\n", pci_name(dev));
+		printk(KERN_ERR DRV_NAME " %s: out of memory\n", pci_name(dev));
 		return -ENOMEM;
 	}
 
diff --git a/drivers/ide/pci/jmicron.c b/drivers/ide/pci/jmicron.c
index 39e221b..545b6e1 100644
--- a/drivers/ide/pci/jmicron.c
+++ b/drivers/ide/pci/jmicron.c
@@ -12,6 +12,8 @@
 #include <linux/ide.h>
 #include <linux/init.h>
 
+#define DRV_NAME "jmicron"
+
 typedef enum {
 	PORT_PATA0 = 0,
 	PORT_PATA1 = 1,
@@ -102,7 +104,7 @@
 };
 
 static const struct ide_port_info jmicron_chipset __devinitdata = {
-	.name		= "JMB",
+	.name		= DRV_NAME,
 	.enablebits	= { { 0x40, 0x01, 0x01 }, { 0x40, 0x10, 0x10 } },
 	.port_ops	= &jmicron_port_ops,
 	.pio_mask	= ATA_PIO5,
diff --git a/drivers/ide/pci/ns87415.c b/drivers/ide/pci/ns87415.c
index afcc742..ffefcd1 100644
--- a/drivers/ide/pci/ns87415.c
+++ b/drivers/ide/pci/ns87415.c
@@ -19,6 +19,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "ns87415"
+
 #ifdef CONFIG_SUPERIO
 /* SUPERIO 87560 is a PoS chip that NatSem denies exists.
  * Unfortunately, it's built-in on all Astro-based PA-RISC workstations
@@ -305,7 +307,7 @@
 };
 
 static const struct ide_port_info ns87415_chipset __devinitdata = {
-	.name		= "NS87415",
+	.name		= DRV_NAME,
 	.init_hwif	= init_hwif_ns87415,
 	.port_ops	= &ns87415_port_ops,
 	.dma_ops	= &ns87415_dma_ops,
diff --git a/drivers/ide/pci/opti621.c b/drivers/ide/pci/opti621.c
index 4895f2f..e28e672 100644
--- a/drivers/ide/pci/opti621.c
+++ b/drivers/ide/pci/opti621.c
@@ -90,6 +90,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "opti621"
+
 #define READ_REG 0	/* index of Read cycle timing register */
 #define WRITE_REG 1	/* index of Write cycle timing register */
 #define CNTRL_REG 3	/* index of Control register */
@@ -200,7 +202,7 @@
 };
 
 static const struct ide_port_info opti621_chipset __devinitdata = {
-	.name		= "OPTI621/X",
+	.name		= DRV_NAME,
 	.enablebits	= { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
 	.port_ops	= &opti621_port_ops,
 	.host_flags	= IDE_HFLAG_NO_DMA,
diff --git a/drivers/ide/pci/pdc202xx_new.c b/drivers/ide/pci/pdc202xx_new.c
index 4c2b669..1f67919 100644
--- a/drivers/ide/pci/pdc202xx_new.c
+++ b/drivers/ide/pci/pdc202xx_new.c
@@ -31,6 +31,8 @@
 #include <asm/pci-bridge.h>
 #endif
 
+#define DRV_NAME "pdc202xx_new"
+
 #undef DEBUG
 
 #ifdef DEBUG
@@ -458,7 +460,7 @@
 
 		if (dev2->irq != dev->irq) {
 			dev2->irq = dev->irq;
-			printk(KERN_INFO "PDC20270 %s: PCI config space "
+			printk(KERN_INFO DRV_NAME " %s: PCI config space "
 				"interrupt fixed\n", pci_name(dev));
 		}
 
@@ -476,9 +478,9 @@
 	.cable_detect		= pdcnew_cable_detect,
 };
 
-#define DECLARE_PDCNEW_DEV(name_str, udma) \
+#define DECLARE_PDCNEW_DEV(udma) \
 	{ \
-		.name		= name_str, \
+		.name		= DRV_NAME, \
 		.init_chipset	= init_chipset_pdcnew, \
 		.port_ops	= &pdcnew_port_ops, \
 		.host_flags	= IDE_HFLAG_POST_SET_MODE | \
@@ -490,13 +492,8 @@
 	}
 
 static const struct ide_port_info pdcnew_chipsets[] __devinitdata = {
-	/* 0 */ DECLARE_PDCNEW_DEV("PDC20268", ATA_UDMA5),
-	/* 1 */ DECLARE_PDCNEW_DEV("PDC20269", ATA_UDMA6),
-	/* 2 */ DECLARE_PDCNEW_DEV("PDC20270", ATA_UDMA5),
-	/* 3 */ DECLARE_PDCNEW_DEV("PDC20271", ATA_UDMA6),
-	/* 4 */ DECLARE_PDCNEW_DEV("PDC20275", ATA_UDMA6),
-	/* 5 */ DECLARE_PDCNEW_DEV("PDC20276", ATA_UDMA6),
-	/* 6 */ DECLARE_PDCNEW_DEV("PDC20277", ATA_UDMA6),
+	/* 0: PDC202{68,70} */		DECLARE_PDCNEW_DEV(ATA_UDMA5),
+	/* 1: PDC202{69,71,75,76,77} */	DECLARE_PDCNEW_DEV(ATA_UDMA6),
 };
 
 /**
@@ -510,13 +507,10 @@
  
 static int __devinit pdc202new_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 {
-	const struct ide_port_info *d;
+	const struct ide_port_info *d = &pdcnew_chipsets[id->driver_data];
 	struct pci_dev *bridge = dev->bus->self;
-	u8 idx = id->driver_data;
 
-	d = &pdcnew_chipsets[idx];
-
-	if (idx == 2 && bridge &&
+	if (dev->device == PCI_DEVICE_ID_PROMISE_20270 && bridge &&
 	    bridge->vendor == PCI_VENDOR_ID_DEC &&
 	    bridge->device == PCI_DEVICE_ID_DEC_21150) {
 		struct pci_dev *dev2;
@@ -534,11 +528,11 @@
 		}
 	}
 
-	if (idx == 5 && bridge &&
+	if (dev->device == PCI_DEVICE_ID_PROMISE_20276 && bridge &&
 	    bridge->vendor == PCI_VENDOR_ID_INTEL &&
 	    (bridge->device == PCI_DEVICE_ID_INTEL_I960 ||
 	     bridge->device == PCI_DEVICE_ID_INTEL_I960RM)) {
-		printk(KERN_INFO "PDC20276 %s: attached to I2O RAID controller,"
+		printk(KERN_INFO DRV_NAME " %s: attached to I2O RAID controller,"
 			" skipping\n", pci_name(dev));
 		return -ENODEV;
 	}
@@ -558,11 +552,11 @@
 static const struct pci_device_id pdc202new_pci_tbl[] = {
 	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20268), 0 },
 	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20269), 1 },
-	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20270), 2 },
-	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20271), 3 },
-	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20275), 4 },
-	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20276), 5 },
-	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20277), 6 },
+	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20270), 0 },
+	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20271), 1 },
+	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20275), 1 },
+	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20276), 1 },
+	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20277), 1 },
 	{ 0, },
 };
 MODULE_DEVICE_TABLE(pci, pdc202new_pci_tbl);
diff --git a/drivers/ide/pci/pdc202xx_old.c b/drivers/ide/pci/pdc202xx_old.c
index 5cb2731..da92d12 100644
--- a/drivers/ide/pci/pdc202xx_old.c
+++ b/drivers/ide/pci/pdc202xx_old.c
@@ -20,6 +20,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "pdc202xx_old"
+
 #define PDC202XX_DEBUG_DRIVE_INFO	0
 
 static const char *pdc_quirk_drives[] = {
@@ -350,9 +352,9 @@
 	.dma_timeout		= pdc202xx_dma_timeout,
 };
 
-#define DECLARE_PDC2026X_DEV(name_str, udma, extra_flags) \
+#define DECLARE_PDC2026X_DEV(udma, extra_flags) \
 	{ \
-		.name		= name_str, \
+		.name		= DRV_NAME, \
 		.init_chipset	= init_chipset_pdc202xx, \
 		.port_ops	= &pdc2026x_port_ops, \
 		.dma_ops	= &pdc2026x_dma_ops, \
@@ -363,8 +365,8 @@
 	}
 
 static const struct ide_port_info pdc202xx_chipsets[] __devinitdata = {
-	{	/* 0 */
-		.name		= "PDC20246",
+	{	/* 0: PDC20246 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_pdc202xx,
 		.port_ops	= &pdc20246_port_ops,
 		.dma_ops	= &pdc20246_dma_ops,
@@ -374,10 +376,10 @@
 		.udma_mask	= ATA_UDMA2,
 	},
 
-	/* 1 */ DECLARE_PDC2026X_DEV("PDC20262", ATA_UDMA4, 0),
-	/* 2 */ DECLARE_PDC2026X_DEV("PDC20263", ATA_UDMA4, 0),
-	/* 3 */ DECLARE_PDC2026X_DEV("PDC20265", ATA_UDMA5, IDE_HFLAG_RQSIZE_256),
-	/* 4 */ DECLARE_PDC2026X_DEV("PDC20267", ATA_UDMA5, IDE_HFLAG_RQSIZE_256),
+	/* 1: PDC2026{2,3} */
+	DECLARE_PDC2026X_DEV(ATA_UDMA4, 0),
+	/* 2: PDC2026{5,7} */
+	DECLARE_PDC2026X_DEV(ATA_UDMA5, IDE_HFLAG_RQSIZE_256),
 };
 
 /**
@@ -396,17 +398,17 @@
 
 	d = &pdc202xx_chipsets[idx];
 
-	if (idx < 3)
+	if (idx < 2)
 		pdc202ata4_fixup_irq(dev, d->name);
 
-	if (idx == 3) {
+	if (dev->vendor == PCI_DEVICE_ID_PROMISE_20265) {
 		struct pci_dev *bridge = dev->bus->self;
 
 		if (bridge &&
 		    bridge->vendor == PCI_VENDOR_ID_INTEL &&
 		    (bridge->device == PCI_DEVICE_ID_INTEL_I960 ||
 		     bridge->device == PCI_DEVICE_ID_INTEL_I960RM)) {
-			printk(KERN_INFO "pdc202xx_old %s: skipping Promise "
+			printk(KERN_INFO DRV_NAME " %s: skipping Promise "
 				"PDC20265 attached to I2O RAID controller\n",
 				pci_name(dev));
 			return -ENODEV;
@@ -419,9 +421,9 @@
 static const struct pci_device_id pdc202xx_pci_tbl[] = {
 	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0 },
 	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1 },
-	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20263), 2 },
-	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20265), 3 },
-	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20267), 4 },
+	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20263), 1 },
+	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20265), 2 },
+	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20267), 2 },
 	{ 0, },
 };
 MODULE_DEVICE_TABLE(pci, pdc202xx_pci_tbl);
diff --git a/drivers/ide/pci/piix.c b/drivers/ide/pci/piix.c
index c16b1ab..9eb411f5c 100644
--- a/drivers/ide/pci/piix.c
+++ b/drivers/ide/pci/piix.c
@@ -54,6 +54,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "piix"
+
 static int no_piix_dma;
 
 /**
@@ -314,9 +316,9 @@
  #define IDE_HFLAGS_PIIX 0
 #endif
 
-#define DECLARE_PIIX_DEV(name_str, udma) \
+#define DECLARE_PIIX_DEV(udma) \
 	{						\
-		.name		= name_str,		\
+		.name		= DRV_NAME,		\
 		.init_hwif	= init_hwif_piix,	\
 		.enablebits	= {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
 		.port_ops	= &piix_port_ops,	\
@@ -327,9 +329,9 @@
 		.udma_mask	= udma,			\
 	}
 
-#define DECLARE_ICH_DEV(name_str, udma) \
+#define DECLARE_ICH_DEV(udma) \
 	{ \
-		.name		= name_str, \
+		.name		= DRV_NAME, \
 		.init_chipset	= init_chipset_ich, \
 		.init_hwif	= init_hwif_ich, \
 		.enablebits	= {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
@@ -342,45 +344,31 @@
 	}
 
 static const struct ide_port_info piix_pci_info[] __devinitdata = {
-	/*  0 */ DECLARE_PIIX_DEV("PIIXa",	0x00),	/* no udma */
-	/*  1 */ DECLARE_PIIX_DEV("PIIXb",	0x00),	/* no udma */
-
-	/*  2 */
+	/* 0: MPIIX */
 	{	/*
 		 * MPIIX actually has only a single IDE channel mapped to
 		 * the primary or secondary ports depending on the value
 		 * of the bit 14 of the IDETIM register at offset 0x6c
 		 */
-		.name		= "MPIIX",
+		.name		= DRV_NAME,
 		.enablebits	= {{0x6d,0xc0,0x80}, {0x6d,0xc0,0xc0}},
 		.host_flags	= IDE_HFLAG_ISA_PORTS | IDE_HFLAG_NO_DMA |
 				  IDE_HFLAGS_PIIX,
 		.pio_mask	= ATA_PIO4,
 		/* This is a painful system best to let it self tune for now */
 	},
-
-	/*  3 */ DECLARE_PIIX_DEV("PIIX3",	0x00),	/* no udma */
-	/*  4 */ DECLARE_PIIX_DEV("PIIX4",	ATA_UDMA2),
-	/*  5 */ DECLARE_ICH_DEV("ICH0",	ATA_UDMA2),
-	/*  6 */ DECLARE_PIIX_DEV("PIIX4",	ATA_UDMA2),
-	/*  7 */ DECLARE_ICH_DEV("ICH",		ATA_UDMA4),
-	/*  8 */ DECLARE_PIIX_DEV("PIIX4",	ATA_UDMA4),
-	/*  9 */ DECLARE_PIIX_DEV("PIIX4",	ATA_UDMA2),
-	/* 10 */ DECLARE_ICH_DEV("ICH2",	ATA_UDMA5),
-	/* 11 */ DECLARE_ICH_DEV("ICH2M",	ATA_UDMA5),
-	/* 12 */ DECLARE_ICH_DEV("ICH3M",	ATA_UDMA5),
-	/* 13 */ DECLARE_ICH_DEV("ICH3",	ATA_UDMA5),
-	/* 14 */ DECLARE_ICH_DEV("ICH4",	ATA_UDMA5),
-	/* 15 */ DECLARE_ICH_DEV("ICH5",	ATA_UDMA5),
-	/* 16 */ DECLARE_ICH_DEV("C-ICH",	ATA_UDMA5),
-	/* 17 */ DECLARE_ICH_DEV("ICH4",	ATA_UDMA5),
-	/* 18 */ DECLARE_ICH_DEV("ICH5-SATA",	ATA_UDMA5),
-	/* 19 */ DECLARE_ICH_DEV("ICH5",	ATA_UDMA5),
-	/* 20 */ DECLARE_ICH_DEV("ICH6",	ATA_UDMA5),
-	/* 21 */ DECLARE_ICH_DEV("ICH7",	ATA_UDMA5),
-	/* 22 */ DECLARE_ICH_DEV("ICH4",	ATA_UDMA5),
-	/* 23 */ DECLARE_ICH_DEV("ESB2",	ATA_UDMA5),
-	/* 24 */ DECLARE_ICH_DEV("ICH8M",	ATA_UDMA5),
+	/* 1: PIIXa/PIIXb/PIIX3 */
+	DECLARE_PIIX_DEV(0x00), /* no udma */
+	/* 2: PIIX4 */
+	DECLARE_PIIX_DEV(ATA_UDMA2),
+	/* 3: ICH0 */
+	DECLARE_ICH_DEV(ATA_UDMA2),
+	/* 4: ICH */
+	DECLARE_ICH_DEV(ATA_UDMA4),
+	/* 5: PIIX4 */
+	DECLARE_PIIX_DEV(ATA_UDMA4),
+	/* 6: ICH[2-7]/ICH[2-3]M/C-ICH/ICH5-SATA/ESB2/ICH8M */
+	DECLARE_ICH_DEV(ATA_UDMA5),
 };
 
 /**
@@ -421,39 +409,39 @@
 			no_piix_dma = 2;
 	}
 	if(no_piix_dma)
-		printk(KERN_WARNING "piix: 450NX errata present, disabling IDE DMA.\n");
+		printk(KERN_WARNING DRV_NAME ": 450NX errata present, disabling IDE DMA.\n");
 	if(no_piix_dma == 2)
-		printk(KERN_WARNING "piix: A BIOS update may resolve this.\n");
+		printk(KERN_WARNING DRV_NAME ": A BIOS update may resolve this.\n");
 }		
 
 static const struct pci_device_id piix_pci_tbl[] = {
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_0),   0 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_1),   1 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX),     2 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371SB_1),   3 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371AB),     4 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AB_1),   5 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82443MX_1),   6 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AA_1),   7 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82372FB_1),   8 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82451NX),     9 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_9),  10 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_8),  11 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_10), 12 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_11), 13 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_11), 14 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_11), 15 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801E_11),  16 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_10), 17 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_0),  1 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_1),  1 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX),    0 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371SB_1),  1 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371AB),    2 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AB_1),  3 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82443MX_1),  2 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AA_1),  4 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82372FB_1),  5 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82451NX),    2 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_9),  6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_8),  6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_10), 6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_11), 6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_11), 6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_11), 6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801E_11),  6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_10), 6 },
 #ifdef CONFIG_BLK_DEV_IDE_SATA
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_1),  18 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_1),  6 },
 #endif
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB_2),      19 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH6_19),    20 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH7_21),    21 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_1),  22 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB2_18),    23 },
-	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH8_6),     24 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB_2),      6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH6_19),    6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH7_21),    6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_1),  6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB2_18),    6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH8_6),     6 },
 	{ 0, },
 };
 MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
diff --git a/drivers/ide/pci/rz1000.c b/drivers/ide/pci/rz1000.c
index f7a3b9a..8d11ee8 100644
--- a/drivers/ide/pci/rz1000.c
+++ b/drivers/ide/pci/rz1000.c
@@ -21,6 +21,8 @@
 #include <linux/ide.h>
 #include <linux/init.h>
 
+#define DRV_NAME "rz1000"
+
 static void __devinit init_hwif_rz1000 (ide_hwif_t *hwif)
 {
 	struct pci_dev *dev = to_pci_dev(hwif->dev);
@@ -40,7 +42,7 @@
 }
 
 static const struct ide_port_info rz1000_chipset __devinitdata = {
-	.name		= "RZ100x",
+	.name		= DRV_NAME,
 	.init_hwif	= init_hwif_rz1000,
 	.chipset	= ide_rz1000,
 	.host_flags	= IDE_HFLAG_NO_DMA,
diff --git a/drivers/ide/pci/sc1200.c b/drivers/ide/pci/sc1200.c
index 6509560..8efaed1 100644
--- a/drivers/ide/pci/sc1200.c
+++ b/drivers/ide/pci/sc1200.c
@@ -22,6 +22,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "sc1200"
+
 #define SC1200_REV_A	0x00
 #define SC1200_REV_B1	0x01
 #define SC1200_REV_B3	0x02
@@ -291,7 +293,7 @@
 };
 
 static const struct ide_port_info sc1200_chipset __devinitdata = {
-	.name		= "SC1200",
+	.name		= DRV_NAME,
 	.port_ops	= &sc1200_port_ops,
 	.dma_ops	= &sc1200_dma_ops,
 	.host_flags	= IDE_HFLAG_SERIALIZE |
diff --git a/drivers/ide/pci/serverworks.c b/drivers/ide/pci/serverworks.c
index 1106ff4..e26bc83 100644
--- a/drivers/ide/pci/serverworks.c
+++ b/drivers/ide/pci/serverworks.c
@@ -38,6 +38,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "serverworks"
+
 #define SVWKS_CSB5_REVISION_NEW	0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
 #define SVWKS_CSB6_REVISION	0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
 
@@ -353,40 +355,44 @@
 #define IDE_HFLAGS_SVWKS IDE_HFLAG_LEGACY_IRQS
 
 static const struct ide_port_info serverworks_chipsets[] __devinitdata = {
-	{	/* 0 */
-		.name		= "SvrWks OSB4",
+	{	/* 0: OSB4 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_svwks,
 		.port_ops	= &osb4_port_ops,
 		.host_flags	= IDE_HFLAGS_SVWKS,
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= 0x00, /* UDMA is problematic on OSB4 */
-	},{	/* 1 */
-		.name		= "SvrWks CSB5",
+	},
+	{	/* 1: CSB5 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_svwks,
 		.port_ops	= &svwks_port_ops,
 		.host_flags	= IDE_HFLAGS_SVWKS,
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= ATA_UDMA5,
-	},{	/* 2 */
-		.name		= "SvrWks CSB6",
+	},
+	{	/* 2: CSB6 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_svwks,
 		.port_ops	= &svwks_port_ops,
 		.host_flags	= IDE_HFLAGS_SVWKS,
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= ATA_UDMA5,
-	},{	/* 3 */
-		.name		= "SvrWks CSB6",
+	},
+	{	/* 3: CSB6-2 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_svwks,
 		.port_ops	= &svwks_port_ops,
 		.host_flags	= IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask	= ATA_UDMA5,
-	},{	/* 4 */
-		.name		= "SvrWks HT1000",
+	},
+	{	/* 4: HT1000 */
+		.name		= DRV_NAME,
 		.init_chipset	= init_chipset_svwks,
 		.port_ops	= &svwks_port_ops,
 		.host_flags	= IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
diff --git a/drivers/ide/pci/siimage.c b/drivers/ide/pci/siimage.c
index fc29f1c..572b479 100644
--- a/drivers/ide/pci/siimage.c
+++ b/drivers/ide/pci/siimage.c
@@ -44,6 +44,8 @@
 #include <linux/init.h>
 #include <linux/io.h>
 
+#define DRV_NAME "siimage"
+
 /**
  *	pdev_is_sata		-	check if device is SATA
  *	@pdev:	PCI device to check
@@ -717,9 +719,9 @@
 	.dma_lost_irq		= ide_dma_lost_irq,
 };
 
-#define DECLARE_SII_DEV(name_str, p_ops)		\
+#define DECLARE_SII_DEV(p_ops)				\
 	{						\
-		.name		= name_str,		\
+		.name		= DRV_NAME,		\
 		.init_chipset	= init_chipset_siimage,	\
 		.init_iops	= init_iops_siimage,	\
 		.port_ops	= p_ops,		\
@@ -730,9 +732,8 @@
 	}
 
 static const struct ide_port_info siimage_chipsets[] __devinitdata = {
-	/* 0 */ DECLARE_SII_DEV("SiI680",		&sil_pata_port_ops),
-	/* 1 */ DECLARE_SII_DEV("SiI3112 Serial ATA",	&sil_sata_port_ops),
-	/* 2 */ DECLARE_SII_DEV("Adaptec AAR-1210SA",	&sil_sata_port_ops)
+	/* 0: SiI680 */  DECLARE_SII_DEV(&sil_pata_port_ops),
+	/* 1: SiI3112 */ DECLARE_SII_DEV(&sil_sata_port_ops)
 };
 
 /**
@@ -761,7 +762,7 @@
 		static int first = 1;
 
 		if (first) {
-			printk(KERN_INFO "siimage: For full SATA support you "
+			printk(KERN_INFO DRV_NAME ": For full SATA support you "
 				"should use the libata sata_sil module.\n");
 			first = 0;
 		}
@@ -780,7 +781,7 @@
 		* seem to get terminally confused in the PCI spaces.
 		*/
 		if (!request_mem_region(bar5, barsize, d.name)) {
-			printk(KERN_WARNING "siimage %s: MMIO ports not "
+			printk(KERN_WARNING DRV_NAME " %s: MMIO ports not "
 				"available\n", pci_name(dev));
 		} else {
 			ioaddr = ioremap(bar5, barsize);
@@ -823,7 +824,7 @@
 	{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_680),    0 },
 #ifdef CONFIG_BLK_DEV_IDE_SATA
 	{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_3112),   1 },
-	{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_1210SA), 2 },
+	{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_1210SA), 1 },
 #endif
 	{ 0, },
 };
diff --git a/drivers/ide/pci/sis5513.c b/drivers/ide/pci/sis5513.c
index 518d8ab..6fcb46c 100644
--- a/drivers/ide/pci/sis5513.c
+++ b/drivers/ide/pci/sis5513.c
@@ -52,6 +52,8 @@
 #include <linux/init.h>
 #include <linux/ide.h>
 
+#define DRV_NAME "sis5513"
+
 /* registers layout and init values are chipset family dependant */
 
 #define ATA_16		0x01
@@ -380,7 +382,7 @@
 		}
 		pci_dev_put(host);
 
-		printk(KERN_INFO "SIS5513 %s: %s %s controller\n",
+		printk(KERN_INFO DRV_NAME " %s: %s %s controller\n",
 			pci_name(dev), SiSHostChipInfo[i].name,
 			chipset_capability[chipset_family]);
 	}
@@ -397,7 +399,7 @@
 			pci_write_config_dword(dev, 0x54, idemisc);
 
 			if (trueid == 0x5518) {
-				printk(KERN_INFO "SIS5513 %s: SiS 962/963 MuTIOL IDE UDMA133 controller\n",
+				printk(KERN_INFO DRV_NAME " %s: SiS 962/963 MuTIOL IDE UDMA133 controller\n",
 					pci_name(dev));
 				chipset_family = ATA_133;
 
@@ -407,7 +409,7 @@
 				 */
 				if ((idemisc & 0x40000000) == 0) {
 					pci_write_config_dword(dev, 0x54, idemisc | 0x40000000);
-					printk(KERN_INFO "SIS5513 %s: Switching to 5513 register mapping\n",
+					printk(KERN_INFO DRV_NAME " %s: Switching to 5513 register mapping\n",
 						pci_name(dev));
 				}
 			}
@@ -432,11 +434,11 @@
 				pci_dev_put(lpc_bridge);
 
 				if (lpc_bridge->revision == 0x10 && (prefctl & 0x80)) {
-					printk(KERN_INFO "SIS5513 %s: SiS 961B MuTIOL IDE UDMA133 controller\n",
+					printk(KERN_INFO DRV_NAME " %s: SiS 961B MuTIOL IDE UDMA133 controller\n",
 						pci_name(dev));
 					chipset_family = ATA_133a;
 				} else {
-					printk(KERN_INFO "SIS5513 %s: SiS 961 MuTIOL IDE UDMA100 controller\n",
+					printk(KERN_INFO DRV_NAME " %s: SiS 961 MuTIOL IDE UDMA100 controller\n",
 						pci_name(dev));
 					chipset_family = ATA_100;
 				}
@@ -560,7 +562,7 @@
 };
 
 static const struct ide_port_info sis5513_chipset __devinitdata = {
-	.name		= "SIS5513",
+	.name		= DRV_NAME,
 	.init_chipset	= init_chipset_sis5513,
 	.enablebits	= { {0x4a, 0x02, 0x02}, {0x4a, 0x04, 0x04} },
 	.host_flags	= IDE_HFLAG_LEGACY_IRQS | IDE_HFLAG_NO_AUTODMA,
diff --git a/drivers/ide/pci/sl82c105.c b/drivers/ide/pci/sl82c105.c
index 72899f8..fa720db 100644
--- a/drivers/ide/pci/sl82c105.c
+++ b/drivers/ide/pci/sl82c105.c
@@ -23,6 +23,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "sl82c105"
+
 #undef DEBUG
 
 #ifdef DEBUG
@@ -301,7 +303,7 @@
 };
 
 static const struct ide_port_info sl82c105_chipset __devinitdata = {
-	.name		= "W82C105",
+	.name		= DRV_NAME,
 	.init_chipset	= init_chipset_sl82c105,
 	.enablebits	= {{0x40,0x01,0x01}, {0x40,0x10,0x10}},
 	.port_ops	= &sl82c105_port_ops,
@@ -328,7 +330,7 @@
 		 * Never ever EVER under any circumstances enable
 		 * DMA when the bridge is this old.
 		 */
-		printk(KERN_INFO "W82C105_IDE: Winbond W83C553 bridge "
+		printk(KERN_INFO DRV_NAME ": Winbond W83C553 bridge "
 				 "revision %d, BM-DMA disabled\n", rev);
 		d.dma_ops = NULL;
 		d.mwdma_mask = 0;
diff --git a/drivers/ide/pci/slc90e66.c b/drivers/ide/pci/slc90e66.c
index fee5ebe..13d1fa4 100644
--- a/drivers/ide/pci/slc90e66.c
+++ b/drivers/ide/pci/slc90e66.c
@@ -15,6 +15,8 @@
 #include <linux/ide.h>
 #include <linux/init.h>
 
+#define DRV_NAME "slc90e66"
+
 static DEFINE_SPINLOCK(slc90e66_lock);
 
 static void slc90e66_set_pio_mode(ide_drive_t *drive, const u8 pio)
@@ -132,7 +134,7 @@
 };
 
 static const struct ide_port_info slc90e66_chipset __devinitdata = {
-	.name		= "SLC90E66",
+	.name		= DRV_NAME,
 	.enablebits	= { {0x41, 0x80, 0x80}, {0x43, 0x80, 0x80} },
 	.port_ops	= &slc90e66_port_ops,
 	.host_flags	= IDE_HFLAG_LEGACY_IRQS,
diff --git a/drivers/ide/pci/tc86c001.c b/drivers/ide/pci/tc86c001.c
index 102cd7c..b1cb8a9 100644
--- a/drivers/ide/pci/tc86c001.c
+++ b/drivers/ide/pci/tc86c001.c
@@ -11,7 +11,7 @@
 #include <linux/pci.h>
 #include <linux/ide.h>
 
-#define DRV_NAME "TC86C001"
+#define DRV_NAME "tc86c001"
 
 static void tc86c001_set_mode(ide_drive_t *drive, const u8 speed)
 {
@@ -193,7 +193,7 @@
 };
 
 static const struct ide_port_info tc86c001_chipset __devinitdata = {
-	.name		= "TC86C001",
+	.name		= DRV_NAME,
 	.init_hwif	= init_hwif_tc86c001,
 	.port_ops	= &tc86c001_port_ops,
 	.dma_ops	= &tc86c001_dma_ops,
diff --git a/drivers/ide/pci/triflex.c b/drivers/ide/pci/triflex.c
index 78e24ac..b77ec35 100644
--- a/drivers/ide/pci/triflex.c
+++ b/drivers/ide/pci/triflex.c
@@ -33,6 +33,8 @@
 #include <linux/ide.h>
 #include <linux/init.h>
 
+#define DRV_NAME "triflex"
+
 static void triflex_set_mode(ide_drive_t *drive, const u8 speed)
 {
 	ide_hwif_t *hwif = HWIF(drive);
@@ -93,7 +95,7 @@
 };
 
 static const struct ide_port_info triflex_device __devinitdata = {
-	.name		= "TRIFLEX",
+	.name		= DRV_NAME,
 	.enablebits	= {{0x80, 0x01, 0x01}, {0x80, 0x02, 0x02}},
 	.port_ops	= &triflex_port_ops,
 	.pio_mask	= ATA_PIO4,
diff --git a/drivers/ide/pci/trm290.c b/drivers/ide/pci/trm290.c
index 7bda5ed..fd28b49 100644
--- a/drivers/ide/pci/trm290.c
+++ b/drivers/ide/pci/trm290.c
@@ -141,6 +141,8 @@
 
 #include <asm/io.h>
 
+#define DRV_NAME "trm290"
+
 static void trm290_prepare_drive (ide_drive_t *drive, unsigned int use_dma)
 {
 	ide_hwif_t *hwif = HWIF(drive);
@@ -245,10 +247,10 @@
 	u8 reg = 0;
 
 	if ((dev->class & 5) && cfg_base)
-		printk(KERN_INFO "TRM290 %s: chip", pci_name(dev));
+		printk(KERN_INFO DRV_NAME " %s: chip", pci_name(dev));
 	else {
 		cfg_base = 0x3df0;
-		printk(KERN_INFO "TRM290 %s: using default", pci_name(dev));
+		printk(KERN_INFO DRV_NAME " %s: using default", pci_name(dev));
 	}
 	printk(KERN_CONT " config base at 0x%04x\n", cfg_base);
 	hwif->config_data = cfg_base;
@@ -325,7 +327,7 @@
 };
 
 static const struct ide_port_info trm290_chipset __devinitdata = {
-	.name		= "TRM290",
+	.name		= DRV_NAME,
 	.init_hwif	= init_hwif_trm290,
 	.chipset	= ide_trm290,
 	.port_ops	= &trm290_port_ops,
diff --git a/drivers/ide/pci/via82cxxx.c b/drivers/ide/pci/via82cxxx.c
index 23332556..170e058 100644
--- a/drivers/ide/pci/via82cxxx.c
+++ b/drivers/ide/pci/via82cxxx.c
@@ -35,6 +35,8 @@
 #include <asm/processor.h>
 #endif
 
+#define DRV_NAME "via82cxxx"
+
 #define VIA_IDE_ENABLE		0x40
 #define VIA_IDE_CONFIG		0x41
 #define VIA_FIFO_CONFIG		0x43
@@ -373,7 +375,7 @@
 };
 
 static const struct ide_port_info via82cxxx_chipset __devinitdata = {
-	.name		= "VP_IDE",
+	.name		= DRV_NAME,
 	.init_chipset	= init_chipset_via82cxxx,
 	.enablebits	= { { 0x40, 0x02, 0x02 }, { 0x40, 0x01, 0x01 } },
 	.port_ops	= &via_port_ops,
@@ -401,7 +403,7 @@
 	 */
 	via_config = via_config_find(&isa);
 	if (!via_config->id) {
-		printk(KERN_WARNING "VP_IDE %s: unknown chipset, skipping\n",
+		printk(KERN_WARNING DRV_NAME " %s: unknown chipset, skipping\n",
 			pci_name(dev));
 		return -ENODEV;
 	}
@@ -409,7 +411,7 @@
 	/*
 	 * Print the boot message.
 	 */
-	printk(KERN_INFO "VP_IDE %s: VIA %s (rev %02x) IDE %sDMA%s\n",
+	printk(KERN_INFO DRV_NAME " %s: VIA %s (rev %02x) IDE %sDMA%s\n",
 		pci_name(dev), via_config->name, isa->revision,
 		via_config->udma_mask ? "U" : "MW",
 		via_dma[via_config->udma_mask ?
@@ -429,9 +431,9 @@
 	}
 
 	if (via_clock < 20000 || via_clock > 50000) {
-		printk(KERN_WARNING "VP_IDE: User given PCI clock speed "
+		printk(KERN_WARNING DRV_NAME ": User given PCI clock speed "
 			"impossible (%d), using 33 MHz instead.\n", via_clock);
-		printk(KERN_WARNING "VP_IDE: Use ide0=ata66 if you want "
+		printk(KERN_WARNING DRV_NAME ": Use ide0=ata66 if you want "
 			"to assume 80-wire cable.\n");
 		via_clock = 33333;
 	}
@@ -453,7 +455,8 @@
 
 	vdev = kzalloc(sizeof(*vdev), GFP_KERNEL);
 	if (!vdev) {
-		printk(KERN_ERR "VP_IDE %s: out of memory :(\n", pci_name(dev));
+		printk(KERN_ERR DRV_NAME " %s: out of memory :(\n",
+			pci_name(dev));
 		return -ENOMEM;
 	}