|  | /* | 
|  | * drivers/mtd/nand/pxa3xx_nand.c | 
|  | * | 
|  | * Copyright © 2005 Intel Corporation | 
|  | * Copyright © 2006 Marvell International Ltd. | 
|  | * | 
|  | * This program is free software; you can redistribute it and/or modify | 
|  | * it under the terms of the GNU General Public License version 2 as | 
|  | * published by the Free Software Foundation. | 
|  | */ | 
|  |  | 
|  | #include <linux/module.h> | 
|  | #include <linux/interrupt.h> | 
|  | #include <linux/platform_device.h> | 
|  | #include <linux/dma-mapping.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/clk.h> | 
|  | #include <linux/mtd/mtd.h> | 
|  | #include <linux/mtd/nand.h> | 
|  | #include <linux/mtd/partitions.h> | 
|  | #include <linux/io.h> | 
|  | #include <linux/irq.h> | 
|  |  | 
|  | #include <mach/dma.h> | 
|  | #include <mach/pxa-regs.h> | 
|  | #include <mach/pxa3xx_nand.h> | 
|  |  | 
|  | #define	CHIP_DELAY_TIMEOUT	(2 * HZ/10) | 
|  |  | 
|  | /* registers and bit definitions */ | 
|  | #define NDCR		(0x00) /* Control register */ | 
|  | #define NDTR0CS0	(0x04) /* Timing Parameter 0 for CS0 */ | 
|  | #define NDTR1CS0	(0x0C) /* Timing Parameter 1 for CS0 */ | 
|  | #define NDSR		(0x14) /* Status Register */ | 
|  | #define NDPCR		(0x18) /* Page Count Register */ | 
|  | #define NDBDR0		(0x1C) /* Bad Block Register 0 */ | 
|  | #define NDBDR1		(0x20) /* Bad Block Register 1 */ | 
|  | #define NDDB		(0x40) /* Data Buffer */ | 
|  | #define NDCB0		(0x48) /* Command Buffer0 */ | 
|  | #define NDCB1		(0x4C) /* Command Buffer1 */ | 
|  | #define NDCB2		(0x50) /* Command Buffer2 */ | 
|  |  | 
|  | #define NDCR_SPARE_EN		(0x1 << 31) | 
|  | #define NDCR_ECC_EN		(0x1 << 30) | 
|  | #define NDCR_DMA_EN		(0x1 << 29) | 
|  | #define NDCR_ND_RUN		(0x1 << 28) | 
|  | #define NDCR_DWIDTH_C		(0x1 << 27) | 
|  | #define NDCR_DWIDTH_M		(0x1 << 26) | 
|  | #define NDCR_PAGE_SZ		(0x1 << 24) | 
|  | #define NDCR_NCSX		(0x1 << 23) | 
|  | #define NDCR_ND_MODE		(0x3 << 21) | 
|  | #define NDCR_NAND_MODE   	(0x0) | 
|  | #define NDCR_CLR_PG_CNT		(0x1 << 20) | 
|  | #define NDCR_CLR_ECC		(0x1 << 19) | 
|  | #define NDCR_RD_ID_CNT_MASK	(0x7 << 16) | 
|  | #define NDCR_RD_ID_CNT(x)	(((x) << 16) & NDCR_RD_ID_CNT_MASK) | 
|  |  | 
|  | #define NDCR_RA_START		(0x1 << 15) | 
|  | #define NDCR_PG_PER_BLK		(0x1 << 14) | 
|  | #define NDCR_ND_ARB_EN		(0x1 << 12) | 
|  |  | 
|  | #define NDSR_MASK		(0xfff) | 
|  | #define NDSR_RDY		(0x1 << 11) | 
|  | #define NDSR_CS0_PAGED		(0x1 << 10) | 
|  | #define NDSR_CS1_PAGED		(0x1 << 9) | 
|  | #define NDSR_CS0_CMDD		(0x1 << 8) | 
|  | #define NDSR_CS1_CMDD		(0x1 << 7) | 
|  | #define NDSR_CS0_BBD		(0x1 << 6) | 
|  | #define NDSR_CS1_BBD		(0x1 << 5) | 
|  | #define NDSR_DBERR		(0x1 << 4) | 
|  | #define NDSR_SBERR		(0x1 << 3) | 
|  | #define NDSR_WRDREQ		(0x1 << 2) | 
|  | #define NDSR_RDDREQ		(0x1 << 1) | 
|  | #define NDSR_WRCMDREQ		(0x1) | 
|  |  | 
|  | #define NDCB0_AUTO_RS		(0x1 << 25) | 
|  | #define NDCB0_CSEL		(0x1 << 24) | 
|  | #define NDCB0_CMD_TYPE_MASK	(0x7 << 21) | 
|  | #define NDCB0_CMD_TYPE(x)	(((x) << 21) & NDCB0_CMD_TYPE_MASK) | 
|  | #define NDCB0_NC		(0x1 << 20) | 
|  | #define NDCB0_DBC		(0x1 << 19) | 
|  | #define NDCB0_ADDR_CYC_MASK	(0x7 << 16) | 
|  | #define NDCB0_ADDR_CYC(x)	(((x) << 16) & NDCB0_ADDR_CYC_MASK) | 
|  | #define NDCB0_CMD2_MASK		(0xff << 8) | 
|  | #define NDCB0_CMD1_MASK		(0xff) | 
|  | #define NDCB0_ADDR_CYC_SHIFT	(16) | 
|  |  | 
|  | /* dma-able I/O address for the NAND data and commands */ | 
|  | #define NDCB0_DMA_ADDR		(0x43100048) | 
|  | #define NDDB_DMA_ADDR		(0x43100040) | 
|  |  | 
|  | /* macros for registers read/write */ | 
|  | #define nand_writel(info, off, val)	\ | 
|  | __raw_writel((val), (info)->mmio_base + (off)) | 
|  |  | 
|  | #define nand_readl(info, off)		\ | 
|  | __raw_readl((info)->mmio_base + (off)) | 
|  |  | 
|  | /* error code and state */ | 
|  | enum { | 
|  | ERR_NONE	= 0, | 
|  | ERR_DMABUSERR	= -1, | 
|  | ERR_SENDCMD	= -2, | 
|  | ERR_DBERR	= -3, | 
|  | ERR_BBERR	= -4, | 
|  | }; | 
|  |  | 
|  | enum { | 
|  | STATE_READY	= 0, | 
|  | STATE_CMD_HANDLE, | 
|  | STATE_DMA_READING, | 
|  | STATE_DMA_WRITING, | 
|  | STATE_DMA_DONE, | 
|  | STATE_PIO_READING, | 
|  | STATE_PIO_WRITING, | 
|  | }; | 
|  |  | 
|  | struct pxa3xx_nand_info { | 
|  | struct nand_chip	nand_chip; | 
|  |  | 
|  | struct platform_device	 *pdev; | 
|  | const struct pxa3xx_nand_flash *flash_info; | 
|  |  | 
|  | struct clk		*clk; | 
|  | void __iomem		*mmio_base; | 
|  |  | 
|  | unsigned int 		buf_start; | 
|  | unsigned int		buf_count; | 
|  |  | 
|  | /* DMA information */ | 
|  | int			drcmr_dat; | 
|  | int			drcmr_cmd; | 
|  |  | 
|  | unsigned char		*data_buff; | 
|  | dma_addr_t 		data_buff_phys; | 
|  | size_t			data_buff_size; | 
|  | int 			data_dma_ch; | 
|  | struct pxa_dma_desc	*data_desc; | 
|  | dma_addr_t 		data_desc_addr; | 
|  |  | 
|  | uint32_t		reg_ndcr; | 
|  |  | 
|  | /* saved column/page_addr during CMD_SEQIN */ | 
|  | int			seqin_column; | 
|  | int			seqin_page_addr; | 
|  |  | 
|  | /* relate to the command */ | 
|  | unsigned int		state; | 
|  |  | 
|  | int			use_ecc;	/* use HW ECC ? */ | 
|  | int			use_dma;	/* use DMA ? */ | 
|  |  | 
|  | size_t			data_size;	/* data size in FIFO */ | 
|  | int 			retcode; | 
|  | struct completion 	cmd_complete; | 
|  |  | 
|  | /* generated NDCBx register values */ | 
|  | uint32_t		ndcb0; | 
|  | uint32_t		ndcb1; | 
|  | uint32_t		ndcb2; | 
|  |  | 
|  | /* calculated from pxa3xx_nand_flash data */ | 
|  | size_t		oob_size; | 
|  | size_t		read_id_bytes; | 
|  |  | 
|  | unsigned int	col_addr_cycles; | 
|  | unsigned int	row_addr_cycles; | 
|  | }; | 
|  |  | 
|  | static int use_dma = 1; | 
|  | module_param(use_dma, bool, 0444); | 
|  | MODULE_PARM_DESC(use_dma, "enable DMA for data transfering to/from NAND HW"); | 
|  |  | 
|  | #ifdef CONFIG_MTD_NAND_PXA3xx_BUILTIN | 
|  | static struct pxa3xx_nand_cmdset smallpage_cmdset = { | 
|  | .read1		= 0x0000, | 
|  | .read2		= 0x0050, | 
|  | .program	= 0x1080, | 
|  | .read_status	= 0x0070, | 
|  | .read_id	= 0x0090, | 
|  | .erase		= 0xD060, | 
|  | .reset		= 0x00FF, | 
|  | .lock		= 0x002A, | 
|  | .unlock		= 0x2423, | 
|  | .lock_status	= 0x007A, | 
|  | }; | 
|  |  | 
|  | static struct pxa3xx_nand_cmdset largepage_cmdset = { | 
|  | .read1		= 0x3000, | 
|  | .read2		= 0x0050, | 
|  | .program	= 0x1080, | 
|  | .read_status	= 0x0070, | 
|  | .read_id	= 0x0090, | 
|  | .erase		= 0xD060, | 
|  | .reset		= 0x00FF, | 
|  | .lock		= 0x002A, | 
|  | .unlock		= 0x2423, | 
|  | .lock_status	= 0x007A, | 
|  | }; | 
|  |  | 
|  | static struct pxa3xx_nand_timing samsung512MbX16_timing = { | 
|  | .tCH	= 10, | 
|  | .tCS	= 0, | 
|  | .tWH	= 20, | 
|  | .tWP	= 40, | 
|  | .tRH	= 30, | 
|  | .tRP	= 40, | 
|  | .tR	= 11123, | 
|  | .tWHR	= 110, | 
|  | .tAR	= 10, | 
|  | }; | 
|  |  | 
|  | static struct pxa3xx_nand_flash samsung512MbX16 = { | 
|  | .timing		= &samsung512MbX16_timing, | 
|  | .cmdset		= &smallpage_cmdset, | 
|  | .page_per_block	= 32, | 
|  | .page_size	= 512, | 
|  | .flash_width	= 16, | 
|  | .dfc_width	= 16, | 
|  | .num_blocks	= 4096, | 
|  | .chip_id	= 0x46ec, | 
|  | }; | 
|  |  | 
|  | static struct pxa3xx_nand_timing micron_timing = { | 
|  | .tCH	= 10, | 
|  | .tCS	= 25, | 
|  | .tWH	= 15, | 
|  | .tWP	= 25, | 
|  | .tRH	= 15, | 
|  | .tRP	= 25, | 
|  | .tR	= 25000, | 
|  | .tWHR	= 60, | 
|  | .tAR	= 10, | 
|  | }; | 
|  |  | 
|  | static struct pxa3xx_nand_flash micron1GbX8 = { | 
|  | .timing		= µn_timing, | 
|  | .cmdset		= &largepage_cmdset, | 
|  | .page_per_block	= 64, | 
|  | .page_size	= 2048, | 
|  | .flash_width	= 8, | 
|  | .dfc_width	= 8, | 
|  | .num_blocks	= 1024, | 
|  | .chip_id	= 0xa12c, | 
|  | }; | 
|  |  | 
|  | static struct pxa3xx_nand_flash micron1GbX16 = { | 
|  | .timing		= µn_timing, | 
|  | .cmdset		= &largepage_cmdset, | 
|  | .page_per_block	= 64, | 
|  | .page_size	= 2048, | 
|  | .flash_width	= 16, | 
|  | .dfc_width	= 16, | 
|  | .num_blocks	= 1024, | 
|  | .chip_id	= 0xb12c, | 
|  | }; | 
|  |  | 
|  | static struct pxa3xx_nand_timing stm2GbX16_timing = { | 
|  | .tCH = 10, | 
|  | .tCS = 35, | 
|  | .tWH = 15, | 
|  | .tWP = 25, | 
|  | .tRH = 15, | 
|  | .tRP = 25, | 
|  | .tR = 25000, | 
|  | .tWHR = 60, | 
|  | .tAR = 10, | 
|  | }; | 
|  |  | 
|  | static struct pxa3xx_nand_flash stm2GbX16 = { | 
|  | .timing = &stm2GbX16_timing, | 
|  | .cmdset	= &largepage_cmdset, | 
|  | .page_per_block = 64, | 
|  | .page_size = 2048, | 
|  | .flash_width = 16, | 
|  | .dfc_width = 16, | 
|  | .num_blocks = 2048, | 
|  | .chip_id = 0xba20, | 
|  | }; | 
|  |  | 
|  | static struct pxa3xx_nand_flash *builtin_flash_types[] = { | 
|  | &samsung512MbX16, | 
|  | µn1GbX8, | 
|  | µn1GbX16, | 
|  | &stm2GbX16, | 
|  | }; | 
|  | #endif /* CONFIG_MTD_NAND_PXA3xx_BUILTIN */ | 
|  |  | 
|  | #define NDTR0_tCH(c)	(min((c), 7) << 19) | 
|  | #define NDTR0_tCS(c)	(min((c), 7) << 16) | 
|  | #define NDTR0_tWH(c)	(min((c), 7) << 11) | 
|  | #define NDTR0_tWP(c)	(min((c), 7) << 8) | 
|  | #define NDTR0_tRH(c)	(min((c), 7) << 3) | 
|  | #define NDTR0_tRP(c)	(min((c), 7) << 0) | 
|  |  | 
|  | #define NDTR1_tR(c)	(min((c), 65535) << 16) | 
|  | #define NDTR1_tWHR(c)	(min((c), 15) << 4) | 
|  | #define NDTR1_tAR(c)	(min((c), 15) << 0) | 
|  |  | 
|  | /* convert nano-seconds to nand flash controller clock cycles */ | 
|  | #define ns2cycle(ns, clk)	(int)(((ns) * (clk / 1000000) / 1000) - 1) | 
|  |  | 
|  | static void pxa3xx_nand_set_timing(struct pxa3xx_nand_info *info, | 
|  | const struct pxa3xx_nand_timing *t) | 
|  | { | 
|  | unsigned long nand_clk = clk_get_rate(info->clk); | 
|  | uint32_t ndtr0, ndtr1; | 
|  |  | 
|  | ndtr0 = NDTR0_tCH(ns2cycle(t->tCH, nand_clk)) | | 
|  | NDTR0_tCS(ns2cycle(t->tCS, nand_clk)) | | 
|  | NDTR0_tWH(ns2cycle(t->tWH, nand_clk)) | | 
|  | NDTR0_tWP(ns2cycle(t->tWP, nand_clk)) | | 
|  | NDTR0_tRH(ns2cycle(t->tRH, nand_clk)) | | 
|  | NDTR0_tRP(ns2cycle(t->tRP, nand_clk)); | 
|  |  | 
|  | ndtr1 = NDTR1_tR(ns2cycle(t->tR, nand_clk)) | | 
|  | NDTR1_tWHR(ns2cycle(t->tWHR, nand_clk)) | | 
|  | NDTR1_tAR(ns2cycle(t->tAR, nand_clk)); | 
|  |  | 
|  | nand_writel(info, NDTR0CS0, ndtr0); | 
|  | nand_writel(info, NDTR1CS0, ndtr1); | 
|  | } | 
|  |  | 
|  | #define WAIT_EVENT_TIMEOUT	10 | 
|  |  | 
|  | static int wait_for_event(struct pxa3xx_nand_info *info, uint32_t event) | 
|  | { | 
|  | int timeout = WAIT_EVENT_TIMEOUT; | 
|  | uint32_t ndsr; | 
|  |  | 
|  | while (timeout--) { | 
|  | ndsr = nand_readl(info, NDSR) & NDSR_MASK; | 
|  | if (ndsr & event) { | 
|  | nand_writel(info, NDSR, ndsr); | 
|  | return 0; | 
|  | } | 
|  | udelay(10); | 
|  | } | 
|  |  | 
|  | return -ETIMEDOUT; | 
|  | } | 
|  |  | 
|  | static int prepare_read_prog_cmd(struct pxa3xx_nand_info *info, | 
|  | uint16_t cmd, int column, int page_addr) | 
|  | { | 
|  | const struct pxa3xx_nand_flash *f = info->flash_info; | 
|  | const struct pxa3xx_nand_cmdset *cmdset = f->cmdset; | 
|  |  | 
|  | /* calculate data size */ | 
|  | switch (f->page_size) { | 
|  | case 2048: | 
|  | info->data_size = (info->use_ecc) ? 2088 : 2112; | 
|  | break; | 
|  | case 512: | 
|  | info->data_size = (info->use_ecc) ? 520 : 528; | 
|  | break; | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | /* generate values for NDCBx registers */ | 
|  | info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0); | 
|  | info->ndcb1 = 0; | 
|  | info->ndcb2 = 0; | 
|  | info->ndcb0 |= NDCB0_ADDR_CYC(info->row_addr_cycles + info->col_addr_cycles); | 
|  |  | 
|  | if (info->col_addr_cycles == 2) { | 
|  | /* large block, 2 cycles for column address | 
|  | * row address starts from 3rd cycle | 
|  | */ | 
|  | info->ndcb1 |= page_addr << 16; | 
|  | if (info->row_addr_cycles == 3) | 
|  | info->ndcb2 = (page_addr >> 16) & 0xff; | 
|  | } else | 
|  | /* small block, 1 cycles for column address | 
|  | * row address starts from 2nd cycle | 
|  | */ | 
|  | info->ndcb1 = page_addr << 8; | 
|  |  | 
|  | if (cmd == cmdset->program) | 
|  | info->ndcb0 |= NDCB0_CMD_TYPE(1) | NDCB0_AUTO_RS; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int prepare_erase_cmd(struct pxa3xx_nand_info *info, | 
|  | uint16_t cmd, int page_addr) | 
|  | { | 
|  | info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0); | 
|  | info->ndcb0 |= NDCB0_CMD_TYPE(2) | NDCB0_AUTO_RS | NDCB0_ADDR_CYC(3); | 
|  | info->ndcb1 = page_addr; | 
|  | info->ndcb2 = 0; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int prepare_other_cmd(struct pxa3xx_nand_info *info, uint16_t cmd) | 
|  | { | 
|  | const struct pxa3xx_nand_cmdset *cmdset = info->flash_info->cmdset; | 
|  |  | 
|  | info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0); | 
|  | info->ndcb1 = 0; | 
|  | info->ndcb2 = 0; | 
|  |  | 
|  | if (cmd == cmdset->read_id) { | 
|  | info->ndcb0 |= NDCB0_CMD_TYPE(3); | 
|  | info->data_size = 8; | 
|  | } else if (cmd == cmdset->read_status) { | 
|  | info->ndcb0 |= NDCB0_CMD_TYPE(4); | 
|  | info->data_size = 8; | 
|  | } else if (cmd == cmdset->reset || cmd == cmdset->lock || | 
|  | cmd == cmdset->unlock) { | 
|  | info->ndcb0 |= NDCB0_CMD_TYPE(5); | 
|  | } else | 
|  | return -EINVAL; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void enable_int(struct pxa3xx_nand_info *info, uint32_t int_mask) | 
|  | { | 
|  | uint32_t ndcr; | 
|  |  | 
|  | ndcr = nand_readl(info, NDCR); | 
|  | nand_writel(info, NDCR, ndcr & ~int_mask); | 
|  | } | 
|  |  | 
|  | static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask) | 
|  | { | 
|  | uint32_t ndcr; | 
|  |  | 
|  | ndcr = nand_readl(info, NDCR); | 
|  | nand_writel(info, NDCR, ndcr | int_mask); | 
|  | } | 
|  |  | 
|  | /* NOTE: it is a must to set ND_RUN firstly, then write command buffer | 
|  | * otherwise, it does not work | 
|  | */ | 
|  | static int write_cmd(struct pxa3xx_nand_info *info) | 
|  | { | 
|  | uint32_t ndcr; | 
|  |  | 
|  | /* clear status bits and run */ | 
|  | nand_writel(info, NDSR, NDSR_MASK); | 
|  |  | 
|  | ndcr = info->reg_ndcr; | 
|  |  | 
|  | ndcr |= info->use_ecc ? NDCR_ECC_EN : 0; | 
|  | ndcr |= info->use_dma ? NDCR_DMA_EN : 0; | 
|  | ndcr |= NDCR_ND_RUN; | 
|  |  | 
|  | nand_writel(info, NDCR, ndcr); | 
|  |  | 
|  | if (wait_for_event(info, NDSR_WRCMDREQ)) { | 
|  | printk(KERN_ERR "timed out writing command\n"); | 
|  | return -ETIMEDOUT; | 
|  | } | 
|  |  | 
|  | nand_writel(info, NDCB0, info->ndcb0); | 
|  | nand_writel(info, NDCB0, info->ndcb1); | 
|  | nand_writel(info, NDCB0, info->ndcb2); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int handle_data_pio(struct pxa3xx_nand_info *info) | 
|  | { | 
|  | int ret, timeout = CHIP_DELAY_TIMEOUT; | 
|  |  | 
|  | switch (info->state) { | 
|  | case STATE_PIO_WRITING: | 
|  | __raw_writesl(info->mmio_base + NDDB, info->data_buff, | 
|  | info->data_size << 2); | 
|  |  | 
|  | enable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD); | 
|  |  | 
|  | ret = wait_for_completion_timeout(&info->cmd_complete, timeout); | 
|  | if (!ret) { | 
|  | printk(KERN_ERR "program command time out\n"); | 
|  | return -1; | 
|  | } | 
|  | break; | 
|  | case STATE_PIO_READING: | 
|  | __raw_readsl(info->mmio_base + NDDB, info->data_buff, | 
|  | info->data_size << 2); | 
|  | break; | 
|  | default: | 
|  | printk(KERN_ERR "%s: invalid state %d\n", __func__, | 
|  | info->state); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | info->state = STATE_READY; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void start_data_dma(struct pxa3xx_nand_info *info, int dir_out) | 
|  | { | 
|  | struct pxa_dma_desc *desc = info->data_desc; | 
|  | int dma_len = ALIGN(info->data_size, 32); | 
|  |  | 
|  | desc->ddadr = DDADR_STOP; | 
|  | desc->dcmd = DCMD_ENDIRQEN | DCMD_WIDTH4 | DCMD_BURST32 | dma_len; | 
|  |  | 
|  | if (dir_out) { | 
|  | desc->dsadr = info->data_buff_phys; | 
|  | desc->dtadr = NDDB_DMA_ADDR; | 
|  | desc->dcmd |= DCMD_INCSRCADDR | DCMD_FLOWTRG; | 
|  | } else { | 
|  | desc->dtadr = info->data_buff_phys; | 
|  | desc->dsadr = NDDB_DMA_ADDR; | 
|  | desc->dcmd |= DCMD_INCTRGADDR | DCMD_FLOWSRC; | 
|  | } | 
|  |  | 
|  | DRCMR(info->drcmr_dat) = DRCMR_MAPVLD | info->data_dma_ch; | 
|  | DDADR(info->data_dma_ch) = info->data_desc_addr; | 
|  | DCSR(info->data_dma_ch) |= DCSR_RUN; | 
|  | } | 
|  |  | 
|  | static void pxa3xx_nand_data_dma_irq(int channel, void *data) | 
|  | { | 
|  | struct pxa3xx_nand_info *info = data; | 
|  | uint32_t dcsr; | 
|  |  | 
|  | dcsr = DCSR(channel); | 
|  | DCSR(channel) = dcsr; | 
|  |  | 
|  | if (dcsr & DCSR_BUSERR) { | 
|  | info->retcode = ERR_DMABUSERR; | 
|  | complete(&info->cmd_complete); | 
|  | } | 
|  |  | 
|  | if (info->state == STATE_DMA_WRITING) { | 
|  | info->state = STATE_DMA_DONE; | 
|  | enable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD); | 
|  | } else { | 
|  | info->state = STATE_READY; | 
|  | complete(&info->cmd_complete); | 
|  | } | 
|  | } | 
|  |  | 
|  | static irqreturn_t pxa3xx_nand_irq(int irq, void *devid) | 
|  | { | 
|  | struct pxa3xx_nand_info *info = devid; | 
|  | unsigned int status; | 
|  |  | 
|  | status = nand_readl(info, NDSR); | 
|  |  | 
|  | if (status & (NDSR_RDDREQ | NDSR_DBERR)) { | 
|  | if (status & NDSR_DBERR) | 
|  | info->retcode = ERR_DBERR; | 
|  |  | 
|  | disable_int(info, NDSR_RDDREQ | NDSR_DBERR); | 
|  |  | 
|  | if (info->use_dma) { | 
|  | info->state = STATE_DMA_READING; | 
|  | start_data_dma(info, 0); | 
|  | } else { | 
|  | info->state = STATE_PIO_READING; | 
|  | complete(&info->cmd_complete); | 
|  | } | 
|  | } else if (status & NDSR_WRDREQ) { | 
|  | disable_int(info, NDSR_WRDREQ); | 
|  | if (info->use_dma) { | 
|  | info->state = STATE_DMA_WRITING; | 
|  | start_data_dma(info, 1); | 
|  | } else { | 
|  | info->state = STATE_PIO_WRITING; | 
|  | complete(&info->cmd_complete); | 
|  | } | 
|  | } else if (status & (NDSR_CS0_BBD | NDSR_CS0_CMDD)) { | 
|  | if (status & NDSR_CS0_BBD) | 
|  | info->retcode = ERR_BBERR; | 
|  |  | 
|  | disable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD); | 
|  | info->state = STATE_READY; | 
|  | complete(&info->cmd_complete); | 
|  | } | 
|  | nand_writel(info, NDSR, status); | 
|  | return IRQ_HANDLED; | 
|  | } | 
|  |  | 
|  | static int pxa3xx_nand_do_cmd(struct pxa3xx_nand_info *info, uint32_t event) | 
|  | { | 
|  | uint32_t ndcr; | 
|  | int ret, timeout = CHIP_DELAY_TIMEOUT; | 
|  |  | 
|  | if (write_cmd(info)) { | 
|  | info->retcode = ERR_SENDCMD; | 
|  | goto fail_stop; | 
|  | } | 
|  |  | 
|  | info->state = STATE_CMD_HANDLE; | 
|  |  | 
|  | enable_int(info, event); | 
|  |  | 
|  | ret = wait_for_completion_timeout(&info->cmd_complete, timeout); | 
|  | if (!ret) { | 
|  | printk(KERN_ERR "command execution timed out\n"); | 
|  | info->retcode = ERR_SENDCMD; | 
|  | goto fail_stop; | 
|  | } | 
|  |  | 
|  | if (info->use_dma == 0 && info->data_size > 0) | 
|  | if (handle_data_pio(info)) | 
|  | goto fail_stop; | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | fail_stop: | 
|  | ndcr = nand_readl(info, NDCR); | 
|  | nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN); | 
|  | udelay(10); | 
|  | return -ETIMEDOUT; | 
|  | } | 
|  |  | 
|  | static int pxa3xx_nand_dev_ready(struct mtd_info *mtd) | 
|  | { | 
|  | struct pxa3xx_nand_info *info = mtd->priv; | 
|  | return (nand_readl(info, NDSR) & NDSR_RDY) ? 1 : 0; | 
|  | } | 
|  |  | 
|  | static inline int is_buf_blank(uint8_t *buf, size_t len) | 
|  | { | 
|  | for (; len > 0; len--) | 
|  | if (*buf++ != 0xff) | 
|  | return 0; | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command, | 
|  | int column, int page_addr) | 
|  | { | 
|  | struct pxa3xx_nand_info *info = mtd->priv; | 
|  | const struct pxa3xx_nand_flash *flash_info = info->flash_info; | 
|  | const struct pxa3xx_nand_cmdset *cmdset = flash_info->cmdset; | 
|  | int ret; | 
|  |  | 
|  | info->use_dma = (use_dma) ? 1 : 0; | 
|  | info->use_ecc = 0; | 
|  | info->data_size = 0; | 
|  | info->state = STATE_READY; | 
|  |  | 
|  | init_completion(&info->cmd_complete); | 
|  |  | 
|  | switch (command) { | 
|  | case NAND_CMD_READOOB: | 
|  | /* disable HW ECC to get all the OOB data */ | 
|  | info->buf_count = mtd->writesize + mtd->oobsize; | 
|  | info->buf_start = mtd->writesize + column; | 
|  |  | 
|  | if (prepare_read_prog_cmd(info, cmdset->read1, column, page_addr)) | 
|  | break; | 
|  |  | 
|  | pxa3xx_nand_do_cmd(info, NDSR_RDDREQ | NDSR_DBERR); | 
|  |  | 
|  | /* We only are OOB, so if the data has error, does not matter */ | 
|  | if (info->retcode == ERR_DBERR) | 
|  | info->retcode = ERR_NONE; | 
|  | break; | 
|  |  | 
|  | case NAND_CMD_READ0: | 
|  | info->use_ecc = 1; | 
|  | info->retcode = ERR_NONE; | 
|  | info->buf_start = column; | 
|  | info->buf_count = mtd->writesize + mtd->oobsize; | 
|  | memset(info->data_buff, 0xFF, info->buf_count); | 
|  |  | 
|  | if (prepare_read_prog_cmd(info, cmdset->read1, column, page_addr)) | 
|  | break; | 
|  |  | 
|  | pxa3xx_nand_do_cmd(info, NDSR_RDDREQ | NDSR_DBERR); | 
|  |  | 
|  | if (info->retcode == ERR_DBERR) { | 
|  | /* for blank page (all 0xff), HW will calculate its ECC as | 
|  | * 0, which is different from the ECC information within | 
|  | * OOB, ignore such double bit errors | 
|  | */ | 
|  | if (is_buf_blank(info->data_buff, mtd->writesize)) | 
|  | info->retcode = ERR_NONE; | 
|  | } | 
|  | break; | 
|  | case NAND_CMD_SEQIN: | 
|  | info->buf_start = column; | 
|  | info->buf_count = mtd->writesize + mtd->oobsize; | 
|  | memset(info->data_buff, 0xff, info->buf_count); | 
|  |  | 
|  | /* save column/page_addr for next CMD_PAGEPROG */ | 
|  | info->seqin_column = column; | 
|  | info->seqin_page_addr = page_addr; | 
|  | break; | 
|  | case NAND_CMD_PAGEPROG: | 
|  | info->use_ecc = (info->seqin_column >= mtd->writesize) ? 0 : 1; | 
|  |  | 
|  | if (prepare_read_prog_cmd(info, cmdset->program, | 
|  | info->seqin_column, info->seqin_page_addr)) | 
|  | break; | 
|  |  | 
|  | pxa3xx_nand_do_cmd(info, NDSR_WRDREQ); | 
|  | break; | 
|  | case NAND_CMD_ERASE1: | 
|  | if (prepare_erase_cmd(info, cmdset->erase, page_addr)) | 
|  | break; | 
|  |  | 
|  | pxa3xx_nand_do_cmd(info, NDSR_CS0_BBD | NDSR_CS0_CMDD); | 
|  | break; | 
|  | case NAND_CMD_ERASE2: | 
|  | break; | 
|  | case NAND_CMD_READID: | 
|  | case NAND_CMD_STATUS: | 
|  | info->use_dma = 0;	/* force PIO read */ | 
|  | info->buf_start = 0; | 
|  | info->buf_count = (command == NAND_CMD_READID) ? | 
|  | info->read_id_bytes : 1; | 
|  |  | 
|  | if (prepare_other_cmd(info, (command == NAND_CMD_READID) ? | 
|  | cmdset->read_id : cmdset->read_status)) | 
|  | break; | 
|  |  | 
|  | pxa3xx_nand_do_cmd(info, NDSR_RDDREQ); | 
|  | break; | 
|  | case NAND_CMD_RESET: | 
|  | if (prepare_other_cmd(info, cmdset->reset)) | 
|  | break; | 
|  |  | 
|  | ret = pxa3xx_nand_do_cmd(info, NDSR_CS0_CMDD); | 
|  | if (ret == 0) { | 
|  | int timeout = 2; | 
|  | uint32_t ndcr; | 
|  |  | 
|  | while (timeout--) { | 
|  | if (nand_readl(info, NDSR) & NDSR_RDY) | 
|  | break; | 
|  | msleep(10); | 
|  | } | 
|  |  | 
|  | ndcr = nand_readl(info, NDCR); | 
|  | nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN); | 
|  | } | 
|  | break; | 
|  | default: | 
|  | printk(KERN_ERR "non-supported command.\n"); | 
|  | break; | 
|  | } | 
|  |  | 
|  | if (info->retcode == ERR_DBERR) { | 
|  | printk(KERN_ERR "double bit error @ page %08x\n", page_addr); | 
|  | info->retcode = ERR_NONE; | 
|  | } | 
|  | } | 
|  |  | 
|  | static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd) | 
|  | { | 
|  | struct pxa3xx_nand_info *info = mtd->priv; | 
|  | char retval = 0xFF; | 
|  |  | 
|  | if (info->buf_start < info->buf_count) | 
|  | /* Has just send a new command? */ | 
|  | retval = info->data_buff[info->buf_start++]; | 
|  |  | 
|  | return retval; | 
|  | } | 
|  |  | 
|  | static u16 pxa3xx_nand_read_word(struct mtd_info *mtd) | 
|  | { | 
|  | struct pxa3xx_nand_info *info = mtd->priv; | 
|  | u16 retval = 0xFFFF; | 
|  |  | 
|  | if (!(info->buf_start & 0x01) && info->buf_start < info->buf_count) { | 
|  | retval = *((u16 *)(info->data_buff+info->buf_start)); | 
|  | info->buf_start += 2; | 
|  | } | 
|  | return retval; | 
|  | } | 
|  |  | 
|  | static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) | 
|  | { | 
|  | struct pxa3xx_nand_info *info = mtd->priv; | 
|  | int real_len = min_t(size_t, len, info->buf_count - info->buf_start); | 
|  |  | 
|  | memcpy(buf, info->data_buff + info->buf_start, real_len); | 
|  | info->buf_start += real_len; | 
|  | } | 
|  |  | 
|  | static void pxa3xx_nand_write_buf(struct mtd_info *mtd, | 
|  | const uint8_t *buf, int len) | 
|  | { | 
|  | struct pxa3xx_nand_info *info = mtd->priv; | 
|  | int real_len = min_t(size_t, len, info->buf_count - info->buf_start); | 
|  |  | 
|  | memcpy(info->data_buff + info->buf_start, buf, real_len); | 
|  | info->buf_start += real_len; | 
|  | } | 
|  |  | 
|  | static int pxa3xx_nand_verify_buf(struct mtd_info *mtd, | 
|  | const uint8_t *buf, int len) | 
|  | { | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void pxa3xx_nand_select_chip(struct mtd_info *mtd, int chip) | 
|  | { | 
|  | return; | 
|  | } | 
|  |  | 
|  | static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this) | 
|  | { | 
|  | struct pxa3xx_nand_info *info = mtd->priv; | 
|  |  | 
|  | /* pxa3xx_nand_send_command has waited for command complete */ | 
|  | if (this->state == FL_WRITING || this->state == FL_ERASING) { | 
|  | if (info->retcode == ERR_NONE) | 
|  | return 0; | 
|  | else { | 
|  | /* | 
|  | * any error make it return 0x01 which will tell | 
|  | * the caller the erase and write fail | 
|  | */ | 
|  | return 0x01; | 
|  | } | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void pxa3xx_nand_ecc_hwctl(struct mtd_info *mtd, int mode) | 
|  | { | 
|  | return; | 
|  | } | 
|  |  | 
|  | static int pxa3xx_nand_ecc_calculate(struct mtd_info *mtd, | 
|  | const uint8_t *dat, uint8_t *ecc_code) | 
|  | { | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pxa3xx_nand_ecc_correct(struct mtd_info *mtd, | 
|  | uint8_t *dat, uint8_t *read_ecc, uint8_t *calc_ecc) | 
|  | { | 
|  | struct pxa3xx_nand_info *info = mtd->priv; | 
|  | /* | 
|  | * Any error include ERR_SEND_CMD, ERR_DBERR, ERR_BUSERR, we | 
|  | * consider it as a ecc error which will tell the caller the | 
|  | * read fail We have distinguish all the errors, but the | 
|  | * nand_read_ecc only check this function return value | 
|  | */ | 
|  | if (info->retcode != ERR_NONE) | 
|  | return -1; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int __readid(struct pxa3xx_nand_info *info, uint32_t *id) | 
|  | { | 
|  | const struct pxa3xx_nand_flash *f = info->flash_info; | 
|  | const struct pxa3xx_nand_cmdset *cmdset = f->cmdset; | 
|  | uint32_t ndcr; | 
|  | uint8_t  id_buff[8]; | 
|  |  | 
|  | if (prepare_other_cmd(info, cmdset->read_id)) { | 
|  | printk(KERN_ERR "failed to prepare command\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | /* Send command */ | 
|  | if (write_cmd(info)) | 
|  | goto fail_timeout; | 
|  |  | 
|  | /* Wait for CMDDM(command done successfully) */ | 
|  | if (wait_for_event(info, NDSR_RDDREQ)) | 
|  | goto fail_timeout; | 
|  |  | 
|  | __raw_readsl(info->mmio_base + NDDB, id_buff, 2); | 
|  | *id = id_buff[0] | (id_buff[1] << 8); | 
|  | return 0; | 
|  |  | 
|  | fail_timeout: | 
|  | ndcr = nand_readl(info, NDCR); | 
|  | nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN); | 
|  | udelay(10); | 
|  | return -ETIMEDOUT; | 
|  | } | 
|  |  | 
|  | static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info, | 
|  | const struct pxa3xx_nand_flash *f) | 
|  | { | 
|  | struct platform_device *pdev = info->pdev; | 
|  | struct pxa3xx_nand_platform_data *pdata = pdev->dev.platform_data; | 
|  | uint32_t ndcr = 0x00000FFF; /* disable all interrupts */ | 
|  |  | 
|  | if (f->page_size != 2048 && f->page_size != 512) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (f->flash_width != 16 && f->flash_width != 8) | 
|  | return -EINVAL; | 
|  |  | 
|  | /* calculate flash information */ | 
|  | info->oob_size = (f->page_size == 2048) ? 64 : 16; | 
|  | info->read_id_bytes = (f->page_size == 2048) ? 4 : 2; | 
|  |  | 
|  | /* calculate addressing information */ | 
|  | info->col_addr_cycles = (f->page_size == 2048) ? 2 : 1; | 
|  |  | 
|  | if (f->num_blocks * f->page_per_block > 65536) | 
|  | info->row_addr_cycles = 3; | 
|  | else | 
|  | info->row_addr_cycles = 2; | 
|  |  | 
|  | ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0; | 
|  | ndcr |= (info->col_addr_cycles == 2) ? NDCR_RA_START : 0; | 
|  | ndcr |= (f->page_per_block == 64) ? NDCR_PG_PER_BLK : 0; | 
|  | ndcr |= (f->page_size == 2048) ? NDCR_PAGE_SZ : 0; | 
|  | ndcr |= (f->flash_width == 16) ? NDCR_DWIDTH_M : 0; | 
|  | ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0; | 
|  |  | 
|  | ndcr |= NDCR_RD_ID_CNT(info->read_id_bytes); | 
|  | ndcr |= NDCR_SPARE_EN; /* enable spare by default */ | 
|  |  | 
|  | info->reg_ndcr = ndcr; | 
|  |  | 
|  | pxa3xx_nand_set_timing(info, f->timing); | 
|  | info->flash_info = f; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pxa3xx_nand_detect_flash(struct pxa3xx_nand_info *info, | 
|  | const struct pxa3xx_nand_platform_data *pdata) | 
|  | { | 
|  | const struct pxa3xx_nand_flash *f; | 
|  | uint32_t id = -1; | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i<pdata->num_flash; ++i) { | 
|  | f = pdata->flash + i; | 
|  |  | 
|  | if (pxa3xx_nand_config_flash(info, f)) | 
|  | continue; | 
|  |  | 
|  | if (__readid(info, &id)) | 
|  | continue; | 
|  |  | 
|  | if (id == f->chip_id) | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_MTD_NAND_PXA3xx_BUILTIN | 
|  | for (i = 0; i < ARRAY_SIZE(builtin_flash_types); i++) { | 
|  |  | 
|  | f = builtin_flash_types[i]; | 
|  |  | 
|  | if (pxa3xx_nand_config_flash(info, f)) | 
|  | continue; | 
|  |  | 
|  | if (__readid(info, &id)) | 
|  | continue; | 
|  |  | 
|  | if (id == f->chip_id) | 
|  | return 0; | 
|  | } | 
|  | #endif | 
|  |  | 
|  | dev_warn(&info->pdev->dev, | 
|  | "failed to detect configured nand flash; found %04x instead of\n", | 
|  | id); | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | /* the maximum possible buffer size for large page with OOB data | 
|  | * is: 2048 + 64 = 2112 bytes, allocate a page here for both the | 
|  | * data buffer and the DMA descriptor | 
|  | */ | 
|  | #define MAX_BUFF_SIZE	PAGE_SIZE | 
|  |  | 
|  | static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info) | 
|  | { | 
|  | struct platform_device *pdev = info->pdev; | 
|  | int data_desc_offset = MAX_BUFF_SIZE - sizeof(struct pxa_dma_desc); | 
|  |  | 
|  | if (use_dma == 0) { | 
|  | info->data_buff = kmalloc(MAX_BUFF_SIZE, GFP_KERNEL); | 
|  | if (info->data_buff == NULL) | 
|  | return -ENOMEM; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | info->data_buff = dma_alloc_coherent(&pdev->dev, MAX_BUFF_SIZE, | 
|  | &info->data_buff_phys, GFP_KERNEL); | 
|  | if (info->data_buff == NULL) { | 
|  | dev_err(&pdev->dev, "failed to allocate dma buffer\n"); | 
|  | return -ENOMEM; | 
|  | } | 
|  |  | 
|  | info->data_buff_size = MAX_BUFF_SIZE; | 
|  | info->data_desc = (void *)info->data_buff + data_desc_offset; | 
|  | info->data_desc_addr = info->data_buff_phys + data_desc_offset; | 
|  |  | 
|  | info->data_dma_ch = pxa_request_dma("nand-data", DMA_PRIO_LOW, | 
|  | pxa3xx_nand_data_dma_irq, info); | 
|  | if (info->data_dma_ch < 0) { | 
|  | dev_err(&pdev->dev, "failed to request data dma\n"); | 
|  | dma_free_coherent(&pdev->dev, info->data_buff_size, | 
|  | info->data_buff, info->data_buff_phys); | 
|  | return info->data_dma_ch; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static struct nand_ecclayout hw_smallpage_ecclayout = { | 
|  | .eccbytes = 6, | 
|  | .eccpos = {8, 9, 10, 11, 12, 13 }, | 
|  | .oobfree = { {2, 6} } | 
|  | }; | 
|  |  | 
|  | static struct nand_ecclayout hw_largepage_ecclayout = { | 
|  | .eccbytes = 24, | 
|  | .eccpos = { | 
|  | 40, 41, 42, 43, 44, 45, 46, 47, | 
|  | 48, 49, 50, 51, 52, 53, 54, 55, | 
|  | 56, 57, 58, 59, 60, 61, 62, 63}, | 
|  | .oobfree = { {2, 38} } | 
|  | }; | 
|  |  | 
|  | static void pxa3xx_nand_init_mtd(struct mtd_info *mtd, | 
|  | struct pxa3xx_nand_info *info) | 
|  | { | 
|  | const struct pxa3xx_nand_flash *f = info->flash_info; | 
|  | struct nand_chip *this = &info->nand_chip; | 
|  |  | 
|  | this->options = (f->flash_width == 16) ? NAND_BUSWIDTH_16: 0; | 
|  |  | 
|  | this->waitfunc		= pxa3xx_nand_waitfunc; | 
|  | this->select_chip	= pxa3xx_nand_select_chip; | 
|  | this->dev_ready		= pxa3xx_nand_dev_ready; | 
|  | this->cmdfunc		= pxa3xx_nand_cmdfunc; | 
|  | this->read_word		= pxa3xx_nand_read_word; | 
|  | this->read_byte		= pxa3xx_nand_read_byte; | 
|  | this->read_buf		= pxa3xx_nand_read_buf; | 
|  | this->write_buf		= pxa3xx_nand_write_buf; | 
|  | this->verify_buf	= pxa3xx_nand_verify_buf; | 
|  |  | 
|  | this->ecc.mode		= NAND_ECC_HW; | 
|  | this->ecc.hwctl		= pxa3xx_nand_ecc_hwctl; | 
|  | this->ecc.calculate	= pxa3xx_nand_ecc_calculate; | 
|  | this->ecc.correct	= pxa3xx_nand_ecc_correct; | 
|  | this->ecc.size		= f->page_size; | 
|  |  | 
|  | if (f->page_size == 2048) | 
|  | this->ecc.layout = &hw_largepage_ecclayout; | 
|  | else | 
|  | this->ecc.layout = &hw_smallpage_ecclayout; | 
|  |  | 
|  | this->chip_delay = 25; | 
|  | } | 
|  |  | 
|  | static int pxa3xx_nand_probe(struct platform_device *pdev) | 
|  | { | 
|  | struct pxa3xx_nand_platform_data *pdata; | 
|  | struct pxa3xx_nand_info *info; | 
|  | struct nand_chip *this; | 
|  | struct mtd_info *mtd; | 
|  | struct resource *r; | 
|  | int ret = 0, irq; | 
|  |  | 
|  | pdata = pdev->dev.platform_data; | 
|  |  | 
|  | if (!pdata) { | 
|  | dev_err(&pdev->dev, "no platform data defined\n"); | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | mtd = kzalloc(sizeof(struct mtd_info) + sizeof(struct pxa3xx_nand_info), | 
|  | GFP_KERNEL); | 
|  | if (!mtd) { | 
|  | dev_err(&pdev->dev, "failed to allocate memory\n"); | 
|  | return -ENOMEM; | 
|  | } | 
|  |  | 
|  | info = (struct pxa3xx_nand_info *)(&mtd[1]); | 
|  | info->pdev = pdev; | 
|  |  | 
|  | this = &info->nand_chip; | 
|  | mtd->priv = info; | 
|  |  | 
|  | info->clk = clk_get(&pdev->dev, NULL); | 
|  | if (IS_ERR(info->clk)) { | 
|  | dev_err(&pdev->dev, "failed to get nand clock\n"); | 
|  | ret = PTR_ERR(info->clk); | 
|  | goto fail_free_mtd; | 
|  | } | 
|  | clk_enable(info->clk); | 
|  |  | 
|  | r = platform_get_resource(pdev, IORESOURCE_DMA, 0); | 
|  | if (r == NULL) { | 
|  | dev_err(&pdev->dev, "no resource defined for data DMA\n"); | 
|  | ret = -ENXIO; | 
|  | goto fail_put_clk; | 
|  | } | 
|  | info->drcmr_dat = r->start; | 
|  |  | 
|  | r = platform_get_resource(pdev, IORESOURCE_DMA, 1); | 
|  | if (r == NULL) { | 
|  | dev_err(&pdev->dev, "no resource defined for command DMA\n"); | 
|  | ret = -ENXIO; | 
|  | goto fail_put_clk; | 
|  | } | 
|  | info->drcmr_cmd = r->start; | 
|  |  | 
|  | irq = platform_get_irq(pdev, 0); | 
|  | if (irq < 0) { | 
|  | dev_err(&pdev->dev, "no IRQ resource defined\n"); | 
|  | ret = -ENXIO; | 
|  | goto fail_put_clk; | 
|  | } | 
|  |  | 
|  | r = platform_get_resource(pdev, IORESOURCE_MEM, 0); | 
|  | if (r == NULL) { | 
|  | dev_err(&pdev->dev, "no IO memory resource defined\n"); | 
|  | ret = -ENODEV; | 
|  | goto fail_put_clk; | 
|  | } | 
|  |  | 
|  | r = request_mem_region(r->start, r->end - r->start + 1, pdev->name); | 
|  | if (r == NULL) { | 
|  | dev_err(&pdev->dev, "failed to request memory resource\n"); | 
|  | ret = -EBUSY; | 
|  | goto fail_put_clk; | 
|  | } | 
|  |  | 
|  | info->mmio_base = ioremap(r->start, r->end - r->start + 1); | 
|  | if (info->mmio_base == NULL) { | 
|  | dev_err(&pdev->dev, "ioremap() failed\n"); | 
|  | ret = -ENODEV; | 
|  | goto fail_free_res; | 
|  | } | 
|  |  | 
|  | ret = pxa3xx_nand_init_buff(info); | 
|  | if (ret) | 
|  | goto fail_free_io; | 
|  |  | 
|  | ret = request_irq(IRQ_NAND, pxa3xx_nand_irq, IRQF_DISABLED, | 
|  | pdev->name, info); | 
|  | if (ret < 0) { | 
|  | dev_err(&pdev->dev, "failed to request IRQ\n"); | 
|  | goto fail_free_buf; | 
|  | } | 
|  |  | 
|  | ret = pxa3xx_nand_detect_flash(info, pdata); | 
|  | if (ret) { | 
|  | dev_err(&pdev->dev, "failed to detect flash\n"); | 
|  | ret = -ENODEV; | 
|  | goto fail_free_irq; | 
|  | } | 
|  |  | 
|  | pxa3xx_nand_init_mtd(mtd, info); | 
|  |  | 
|  | platform_set_drvdata(pdev, mtd); | 
|  |  | 
|  | if (nand_scan(mtd, 1)) { | 
|  | dev_err(&pdev->dev, "failed to scan nand\n"); | 
|  | ret = -ENXIO; | 
|  | goto fail_free_irq; | 
|  | } | 
|  |  | 
|  | return add_mtd_partitions(mtd, pdata->parts, pdata->nr_parts); | 
|  |  | 
|  | fail_free_irq: | 
|  | free_irq(IRQ_NAND, info); | 
|  | fail_free_buf: | 
|  | if (use_dma) { | 
|  | pxa_free_dma(info->data_dma_ch); | 
|  | dma_free_coherent(&pdev->dev, info->data_buff_size, | 
|  | info->data_buff, info->data_buff_phys); | 
|  | } else | 
|  | kfree(info->data_buff); | 
|  | fail_free_io: | 
|  | iounmap(info->mmio_base); | 
|  | fail_free_res: | 
|  | release_mem_region(r->start, r->end - r->start + 1); | 
|  | fail_put_clk: | 
|  | clk_disable(info->clk); | 
|  | clk_put(info->clk); | 
|  | fail_free_mtd: | 
|  | kfree(mtd); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int pxa3xx_nand_remove(struct platform_device *pdev) | 
|  | { | 
|  | struct mtd_info *mtd = platform_get_drvdata(pdev); | 
|  | struct pxa3xx_nand_info *info = mtd->priv; | 
|  |  | 
|  | platform_set_drvdata(pdev, NULL); | 
|  |  | 
|  | del_mtd_device(mtd); | 
|  | del_mtd_partitions(mtd); | 
|  | free_irq(IRQ_NAND, info); | 
|  | if (use_dma) { | 
|  | pxa_free_dma(info->data_dma_ch); | 
|  | dma_free_writecombine(&pdev->dev, info->data_buff_size, | 
|  | info->data_buff, info->data_buff_phys); | 
|  | } else | 
|  | kfree(info->data_buff); | 
|  | kfree(mtd); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_PM | 
|  | static int pxa3xx_nand_suspend(struct platform_device *pdev, pm_message_t state) | 
|  | { | 
|  | struct mtd_info *mtd = (struct mtd_info *)platform_get_drvdata(pdev); | 
|  | struct pxa3xx_nand_info *info = mtd->priv; | 
|  |  | 
|  | if (info->state != STATE_READY) { | 
|  | dev_err(&pdev->dev, "driver busy, state = %d\n", info->state); | 
|  | return -EAGAIN; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pxa3xx_nand_resume(struct platform_device *pdev) | 
|  | { | 
|  | struct mtd_info *mtd = (struct mtd_info *)platform_get_drvdata(pdev); | 
|  | struct pxa3xx_nand_info *info = mtd->priv; | 
|  |  | 
|  | clk_enable(info->clk); | 
|  |  | 
|  | return pxa3xx_nand_config_flash(info, info->flash_info); | 
|  | } | 
|  | #else | 
|  | #define pxa3xx_nand_suspend	NULL | 
|  | #define pxa3xx_nand_resume	NULL | 
|  | #endif | 
|  |  | 
|  | static struct platform_driver pxa3xx_nand_driver = { | 
|  | .driver = { | 
|  | .name	= "pxa3xx-nand", | 
|  | }, | 
|  | .probe		= pxa3xx_nand_probe, | 
|  | .remove		= pxa3xx_nand_remove, | 
|  | .suspend	= pxa3xx_nand_suspend, | 
|  | .resume		= pxa3xx_nand_resume, | 
|  | }; | 
|  |  | 
|  | static int __init pxa3xx_nand_init(void) | 
|  | { | 
|  | return platform_driver_register(&pxa3xx_nand_driver); | 
|  | } | 
|  | module_init(pxa3xx_nand_init); | 
|  |  | 
|  | static void __exit pxa3xx_nand_exit(void) | 
|  | { | 
|  | platform_driver_unregister(&pxa3xx_nand_driver); | 
|  | } | 
|  | module_exit(pxa3xx_nand_exit); | 
|  |  | 
|  | MODULE_LICENSE("GPL"); | 
|  | MODULE_DESCRIPTION("PXA3xx NAND controller driver"); |