ARM: OMAP: Use gpiolib with tps65010 for OSK 5912
Convert OSK board to use new tps65010 gpiolib support. This
includes moving its LED support from leds-osk to gpio-leds,
giving more trigger options and a net platform code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index dd9ece8..4f9baba 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -32,6 +32,7 @@
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/i2c.h>
+#include <linux/leds.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
@@ -183,11 +184,80 @@
&osk5912_mcbsp1_device,
};
+static struct gpio_led tps_leds[] = {
+ /* NOTE: D9 and D2 have hardware blink support.
+ * Also, D9 requires non-battery power.
+ */
+ { .gpio = OSK_TPS_GPIO_LED_D9, .name = "d9", },
+ { .gpio = OSK_TPS_GPIO_LED_D2, .name = "d2", },
+ { .gpio = OSK_TPS_GPIO_LED_D3, .name = "d3", .active_low = 1,
+ .default_trigger = "heartbeat", },
+};
+
+static struct gpio_led_platform_data tps_leds_data = {
+ .num_leds = 3,
+ .leds = tps_leds,
+};
+
+static struct platform_device osk5912_tps_leds = {
+ .name = "leds-gpio",
+ .id = 0,
+ .dev.platform_data = &tps_leds_data,
+};
+
+static int osk_tps_setup(struct i2c_client *client, void *context)
+{
+ /* Set GPIO 1 HIGH to disable VBUS power supply;
+ * OHCI driver powers it up/down as needed.
+ */
+ gpio_request(OSK_TPS_GPIO_USB_PWR_EN, "n_vbus_en");
+ gpio_direction_output(OSK_TPS_GPIO_USB_PWR_EN, 1);
+
+ /* Set GPIO 2 high so LED D3 is off by default */
+ tps65010_set_gpio_out_value(GPIO2, HIGH);
+
+ /* Set GPIO 3 low to take ethernet out of reset */
+ gpio_request(OSK_TPS_GPIO_LAN_RESET, "smc_reset");
+ gpio_direction_output(OSK_TPS_GPIO_LAN_RESET, 0);
+
+ /* GPIO4 is VDD_DSP */
+ gpio_request(OSK_TPS_GPIO_DSP_PWR_EN, "dsp_power");
+ gpio_direction_output(OSK_TPS_GPIO_DSP_PWR_EN, 1);
+ /* REVISIT if DSP support isn't configured, power it off ... */
+
+ /* Let LED1 (D9) blink; leds-gpio may override it */
+ tps65010_set_led(LED1, BLINK);
+
+ /* Set LED2 off by default */
+ tps65010_set_led(LED2, OFF);
+
+ /* Enable LOW_PWR handshake */
+ tps65010_set_low_pwr(ON);
+
+ /* Switch VLDO2 to 3.0V for AIC23 */
+ tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V
+ | TPS_LDO1_ENABLE);
+
+ /* register these three LEDs */
+ osk5912_tps_leds.dev.parent = &client->dev;
+ platform_device_register(&osk5912_tps_leds);
+
+ return 0;
+}
+
+static struct tps65010_board tps_board = {
+ .base = OSK_TPS_GPIO_BASE,
+ .outmask = 0x0f,
+ .setup = osk_tps_setup,
+};
+
static struct i2c_board_info __initdata osk_i2c_board_info[] = {
{
I2C_BOARD_INFO("tps65010", 0x48),
.type = "tps65010",
.irq = OMAP_GPIO_IRQ(OMAP_MPUIO(1)),
+ .platform_data = &tps_board,
+
},
/* TODO when driver support is ready:
* - aic23 audio chip at 0x1a
@@ -488,44 +558,6 @@
omap1_map_common_io();
}
-#ifdef CONFIG_TPS65010
-static int __init osk_tps_init(void)
-{
- if (!machine_is_omap_osk())
- return 0;
-
- /* Let LED1 (D9) blink */
- tps65010_set_led(LED1, BLINK);
-
- /* Disable LED 2 (D2) */
- tps65010_set_led(LED2, OFF);
-
- /* Set GPIO 1 HIGH to disable VBUS power supply;
- * OHCI driver powers it up/down as needed.
- */
- tps65010_set_gpio_out_value(GPIO1, HIGH);
-
- /* Set GPIO 2 low to turn on LED D3 */
- tps65010_set_gpio_out_value(GPIO2, HIGH);
-
- /* Set GPIO 3 low to take ethernet out of reset */
- tps65010_set_gpio_out_value(GPIO3, LOW);
-
- /* gpio4 for VDD_DSP */
- /* FIXME send power to DSP iff it's configured */
-
- /* Enable LOW_PWR */
- tps65010_set_low_pwr(ON);
-
- /* Switch VLDO2 to 3.0V for AIC23 */
- tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V
- | TPS_LDO1_ENABLE);
-
- return 0;
-}
-fs_initcall(osk_tps_init);
-#endif
-
MACHINE_START(OMAP_OSK, "TI-OSK")
/* Maintainer: Dirk Behme <dirk.behme@de.bosch.com> */
.phys_io = 0xfff00000,