| MPC5200 Device Tree Bindings |
| ---------------------------- |
| |
| (c) 2006-2009 Secret Lab Technologies Ltd |
| Grant Likely <grant.likely@secretlab.ca> |
| |
| Naming conventions |
| ------------------ |
| For mpc5200 on-chip devices, the format for each compatible value is |
| <chip>-<device>[-<mode>]. The OS should be able to match a device driver |
| to the device based solely on the compatible value. If two drivers |
| match on the compatible list; the 'most compatible' driver should be |
| selected. |
| |
| The split between the MPC5200 and the MPC5200B leaves a bit of a |
| conundrum. How should the compatible property be set up to provide |
| maximum compatibility information; but still accurately describe the |
| chip? For the MPC5200; the answer is easy. Most of the SoC devices |
| originally appeared on the MPC5200. Since they didn't exist anywhere |
| else; the 5200 compatible properties will contain only one item; |
| "fsl,mpc5200-<device>". |
| |
| The 5200B is almost the same as the 5200, but not quite. It fixes |
| silicon bugs and it adds a small number of enhancements. Most of the |
| devices either provide exactly the same interface as on the 5200. A few |
| devices have extra functions but still have a backwards compatible mode. |
| To express this information as completely as possible, 5200B device trees |
| should have two items in the compatible list: |
| compatible = "fsl,mpc5200b-<device>","fsl,mpc5200-<device>"; |
| |
| It is *strongly* recommended that 5200B device trees follow this convention |
| (instead of only listing the base mpc5200 item). |
| |
| ie. ethernet on mpc5200: compatible = "fsl,mpc5200-fec"; |
| ethernet on mpc5200b: compatible = "fsl,mpc5200b-fec", "fsl,mpc5200-fec"; |
| |
| Modal devices, like PSCs, also append the configured function to the |
| end of the compatible field. ie. A PSC in i2s mode would specify |
| "fsl,mpc5200-psc-i2s", not "fsl,mpc5200-i2s". This convention is chosen to |
| avoid naming conflicts with non-psc devices providing the same |
| function. For example, "fsl,mpc5200-spi" and "fsl,mpc5200-psc-spi" describe |
| the mpc5200 simple spi device and a PSC spi mode respectively. |
| |
| At the time of writing, exact chip may be either 'fsl,mpc5200' or |
| 'fsl,mpc5200b'. |
| |
| The soc node |
| ------------ |
| This node describes the on chip SOC peripherals. Every mpc5200 based |
| board will have this node, and as such there is a common naming |
| convention for SOC devices. |
| |
| Required properties: |
| name description |
| ---- ----------- |
| ranges Memory range of the internal memory mapped registers. |
| Should be <0 [baseaddr] 0xc000> |
| reg Should be <[baseaddr] 0x100> |
| compatible mpc5200: "fsl,mpc5200-immr" |
| mpc5200b: "fsl,mpc5200b-immr" |
| system-frequency 'fsystem' frequency in Hz; XLB, IPB, USB and PCI |
| clocks are derived from the fsystem clock. |
| bus-frequency IPB bus frequency in Hz. Clock rate |
| used by most of the soc devices. |
| |
| soc child nodes |
| --------------- |
| Any on chip SOC devices available to Linux must appear as soc5200 child nodes. |
| |
| Note: The tables below show the value for the mpc5200. A mpc5200b device |
| tree should use the "fsl,mpc5200b-<device>","fsl,mpc5200-<device>" form. |
| |
| Required soc5200 child nodes: |
| name compatible Description |
| ---- ---------- ----------- |
| cdm@<addr> fsl,mpc5200-cdm Clock Distribution |
| interrupt-controller@<addr> fsl,mpc5200-pic need an interrupt |
| controller to boot |
| bestcomm@<addr> fsl,mpc5200-bestcomm Bestcomm DMA controller |
| |
| Recommended soc5200 child nodes; populate as needed for your board |
| name compatible Description |
| ---- ---------- ----------- |
| timer@<addr> fsl,mpc5200-gpt General purpose timers |
| gpio@<addr> fsl,mpc5200-gpio MPC5200 simple gpio controller |
| gpio@<addr> fsl,mpc5200-gpio-wkup MPC5200 wakeup gpio controller |
| rtc@<addr> fsl,mpc5200-rtc Real time clock |
| mscan@<addr> fsl,mpc5200-mscan CAN bus controller |
| pci@<addr> fsl,mpc5200-pci PCI bridge |
| serial@<addr> fsl,mpc5200-psc-uart PSC in serial mode |
| i2s@<addr> fsl,mpc5200-psc-i2s PSC in i2s mode |
| ac97@<addr> fsl,mpc5200-psc-ac97 PSC in ac97 mode |
| spi@<addr> fsl,mpc5200-psc-spi PSC in spi mode |
| irda@<addr> fsl,mpc5200-psc-irda PSC in IrDA mode |
| spi@<addr> fsl,mpc5200-spi MPC5200 spi device |
| ethernet@<addr> fsl,mpc5200-fec MPC5200 ethernet device |
| ata@<addr> fsl,mpc5200-ata IDE ATA interface |
| i2c@<addr> fsl,mpc5200-i2c I2C controller |
| usb@<addr> fsl,mpc5200-ohci,ohci-be USB controller |
| xlb@<addr> fsl,mpc5200-xlb XLB arbitrator |
| |
| fsl,mpc5200-gpt nodes |
| --------------------- |
| On the mpc5200 and 5200b, GPT0 has a watchdog timer function. If the board |
| design supports the internal wdt, then the device node for GPT0 should |
| include the empty property 'fsl,has-wdt'. Note that this does not activate |
| the watchdog. The timer will function as a GPT if the timer api is used, and |
| it will function as watchdog if the watchdog device is used. The watchdog |
| mode has priority over the gpt mode, i.e. if the watchdog is activated, any |
| gpt api call to this timer will fail with -EBUSY. |
| |
| If you add the property |
| fsl,wdt-on-boot = <n>; |
| GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it. |
| If n>0, the watchdog is started with a timeout of n seconds. If n=0, the |
| configuration of the watchdog is not touched. This is useful in two cases: |
| - just mark GPT0 as watchdog, blocking gpt accesses, and configure it later; |
| - do not touch a configuration assigned by the boot loader which supervises |
| the boot process itself. |
| |
| The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option. |
| |
| An mpc5200-gpt can be used as a single line GPIO controller. To do so, |
| add the following properties to the gpt node: |
| gpio-controller; |
| #gpio-cells = <2>; |
| When referencing the GPIO line from another node, the first cell must always |
| be zero and the second cell represents the gpio flags and described in the |
| gpio device tree binding. |
| |
| An mpc5200-gpt can be used as a single line edge sensitive interrupt |
| controller. To do so, add the following properties to the gpt node: |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| When referencing the IRQ line from another node, the cell represents the |
| sense mode; 1 for edge rising, 2 for edge falling. |
| |
| fsl,mpc5200-psc nodes |
| --------------------- |
| The PSCs should include a cell-index which is the index of the PSC in |
| hardware. cell-index is used to determine which shared SoC registers to |
| use when setting up PSC clocking. cell-index number starts at '0'. ie: |
| PSC1 has 'cell-index = <0>' |
| PSC4 has 'cell-index = <3>' |
| |
| PSC in i2s mode: The mpc5200 and mpc5200b PSCs are not compatible when in |
| i2s mode. An 'mpc5200b-psc-i2s' node cannot include 'mpc5200-psc-i2s' in the |
| compatible field. |
| |
| |
| fsl,mpc5200-gpio and fsl,mpc5200-gpio-wkup nodes |
| ------------------------------------------------ |
| Each GPIO controller node should have the empty property gpio-controller and |
| #gpio-cells set to 2. First cell is the GPIO number which is interpreted |
| according to the bit numbers in the GPIO control registers. The second cell |
| is for flags which is currently unused. |
| |
| fsl,mpc5200-fec nodes |
| --------------------- |
| The FEC node can specify one of the following properties to configure |
| the MII link: |
| - fsl,7-wire-mode - An empty property that specifies the link uses 7-wire |
| mode instead of MII |
| - current-speed - Specifies that the MII should be configured for a fixed |
| speed. This property should contain two cells. The |
| first cell specifies the speed in Mbps and the second |
| should be '0' for half duplex and '1' for full duplex |
| - phy-handle - Contains a phandle to an Ethernet PHY. |
| |
| Interrupt controller (fsl,mpc5200-pic) node |
| ------------------------------------------- |
| The mpc5200 pic binding splits hardware IRQ numbers into two levels. The |
| split reflects the layout of the PIC hardware itself, which groups |
| interrupts into one of three groups; CRIT, MAIN or PERP. Also, the |
| Bestcomm dma engine has it's own set of interrupt sources which are |
| cascaded off of peripheral interrupt 0, which the driver interprets as a |
| fourth group, SDMA. |
| |
| The interrupts property for device nodes using the mpc5200 pic consists |
| of three cells; <L1 L2 level> |
| |
| L1 := [CRIT=0, MAIN=1, PERP=2, SDMA=3] |
| L2 := interrupt number; directly mapped from the value in the |
| "ICTL PerStat, MainStat, CritStat Encoded Register" |
| level := [LEVEL_HIGH=0, EDGE_RISING=1, EDGE_FALLING=2, LEVEL_LOW=3] |
| |
| For external IRQs, use the following interrupt property values (how to |
| specify external interrupts is a frequently asked question): |
| External interrupts: |
| external irq0: interrupts = <0 0 n>; |
| external irq1: interrupts = <1 1 n>; |
| external irq2: interrupts = <1 2 n>; |
| external irq3: interrupts = <1 3 n>; |
| 'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low) |
| |
| fsl,mpc5200-mscan nodes |
| ----------------------- |
| See file can.txt in this directory. |