board: 8930: Add support for isa1200 haptic chip
Enable haptics on 8930 CDP Phase 2. Remove haptics
support for Phase 1 CDPs as all have been upgraded
to Phase 2. Configure necessary clock and gpio pins.
Enable regulator to pull up i2c line for communication.
Change-Id: Ifcd1f9332cce382aa99b520ca85fe4ccf08ad2f2
Signed-off-by: Amy Maloche <amaloche@codeaurora.org>
diff --git a/arch/arm/mach-msm/board-8930.c b/arch/arm/mach-msm/board-8930.c
index 59651a7..dc6c135 100644
--- a/arch/arm/mach-msm/board-8930.c
+++ b/arch/arm/mach-msm/board-8930.c
@@ -1218,127 +1218,25 @@
#/* TODO: Remove this once PM8038 physically becomes
* available.
*/
-#ifndef MSM8930_PHASE_2
-#define PM_HAP_EN_GPIO PM8921_GPIO_PM_TO_SYS(33)
-#define PM_HAP_LEN_GPIO PM8921_GPIO_PM_TO_SYS(20)
-#else
#define ISA1200_HAP_EN_GPIO 77
#define ISA1200_HAP_LEN_GPIO 78
#define ISA1200_HAP_CLK PM8038_GPIO_PM_TO_SYS(7)
-#endif
-
-#ifndef MSM8930_PHASE_2
-static struct msm_xo_voter *xo_handle_d1;
-#endif
static int isa1200_power(int on)
{
-#ifndef MSM8930_PHASE_2
- int rc = 0;
-
- gpio_set_value(HAP_SHIFT_LVL_OE_GPIO, !!on);
-
- rc = on ? msm_xo_mode_vote(xo_handle_d1, MSM_XO_MODE_ON) :
- msm_xo_mode_vote(xo_handle_d1, MSM_XO_MODE_OFF);
- if (rc < 0) {
- pr_err("%s: failed to %svote for TCXO D1 buffer%d\n",
- __func__, on ? "" : "de-", rc);
- goto err_xo_vote;
- }
-
- return 0;
-
-err_xo_vote:
- gpio_set_value(HAP_SHIFT_LVL_OE_GPIO, !on);
- return rc;
-#else
gpio_set_value_cansleep(ISA1200_HAP_CLK, !!on);
return 0;
-#endif
-
}
static int isa1200_dev_setup(bool enable)
{
int rc = 0;
-#ifndef MSM8930_PHASE_2
- struct pm_gpio hap_gpio_config = {
- .direction = PM_GPIO_DIR_OUT,
- .pull = PM_GPIO_PULL_NO,
- .out_strength = PM_GPIO_STRENGTH_HIGH,
- .function = PM_GPIO_FUNC_NORMAL,
- .inv_int_pol = 0,
- .vin_sel = 2,
- .output_buffer = PM_GPIO_OUT_BUF_CMOS,
- .output_value = 0,
- };
-
- if (enable == true) {
- rc = pm8xxx_gpio_config(PM_HAP_EN_GPIO, &hap_gpio_config);
- if (rc) {
- pr_err("%s: pm8921 gpio %d config failed(%d)\n",
- __func__, PM_HAP_EN_GPIO, rc);
- return rc;
- }
-
- rc = pm8xxx_gpio_config(PM_HAP_LEN_GPIO, &hap_gpio_config);
- if (rc) {
- pr_err("%s: pm8921 gpio %d config failed(%d)\n",
- __func__, PM_HAP_LEN_GPIO, rc);
- return rc;
- }
-
- rc = gpio_request(HAP_SHIFT_LVL_OE_GPIO, "hap_shft_lvl_oe");
- if (rc) {
- pr_err("%s: unable to request gpio %d (%d)\n",
- __func__, HAP_SHIFT_LVL_OE_GPIO, rc);
- return rc;
- }
-
- rc = gpio_direction_output(HAP_SHIFT_LVL_OE_GPIO, 0);
- if (rc) {
- pr_err("%s: Unable to set direction\n", __func__);
- goto free_gpio;
- }
-
- xo_handle_d1 = msm_xo_get(MSM_XO_TCXO_D1, "isa1200");
- if (IS_ERR(xo_handle_d1)) {
- rc = PTR_ERR(xo_handle_d1);
- pr_err("%s: failed to get the handle for D1(%d)\n",
- __func__, rc);
- goto gpio_set_dir;
- }
- } else {
- gpio_free(HAP_SHIFT_LVL_OE_GPIO);
-
- msm_xo_put(xo_handle_d1);
- }
-
- return 0;
-
-gpio_set_dir:
- gpio_set_value(HAP_SHIFT_LVL_OE_GPIO, 0);
-free_gpio:
- gpio_free(HAP_SHIFT_LVL_OE_GPIO);
- return rc;
-#else
- struct pm_gpio hap_clk_gpio_config = {
- .direction = PM_GPIO_DIR_OUT,
- .pull = PM_GPIO_PULL_NO,
- .out_strength = PM_GPIO_STRENGTH_HIGH,
- .function = PM_GPIO_FUNC_1,
- .inv_int_pol = 0,
- .vin_sel = PM_GPIO_VIN_S4,
- .output_buffer = PM_GPIO_OUT_BUF_CMOS,
- .output_value = 0,
- };
-
- rc = pm8xxx_gpio_config(ISA1200_HAP_CLK, &hap_clk_gpio_config);
+ rc = pm8xxx_aux_clk_control(CLK_MP3_1, XO_DIV_1, enable);
if (rc) {
- pr_err("%s: pm8038 gpio %d config failed(%d)\n",
- __func__, ISA1200_HAP_CLK, rc);
+ pr_err("%s: unable to write aux clock register(%d)\n",
+ __func__, rc);
return rc;
}
@@ -1363,38 +1261,29 @@
fail_gpio_req:
return rc;
-#endif
}
static struct isa1200_regulator isa1200_reg_data[] = {
-#ifndef MSM8930_PHASE_2
- {
- .name = "vcc_i2c",
- .min_uV = ISA_I2C_VTG_MIN_UV,
- .max_uV = ISA_I2C_VTG_MAX_UV,
- .load_uA = ISA_I2C_CURR_UA,
- },
-#else
{
.name = "vddp",
.min_uV = ISA_I2C_VTG_MIN_UV,
.max_uV = ISA_I2C_VTG_MAX_UV,
.load_uA = ISA_I2C_CURR_UA,
},
-#endif
+ {
+ .name = "vcc_i2c",
+ .min_uV = ISA_I2C_VTG_MIN_UV,
+ .max_uV = ISA_I2C_VTG_MAX_UV,
+ .load_uA = ISA_I2C_CURR_UA,
+ },
};
static struct isa1200_platform_data isa1200_1_pdata = {
.name = "vibrator",
.dev_setup = isa1200_dev_setup,
.power_on = isa1200_power,
-#ifndef MSM8930_PHASE_2
- .hap_en_gpio = PM_HAP_EN_GPIO,
- .hap_len_gpio = PM_HAP_LEN_GPIO,
-#else
.hap_en_gpio = ISA1200_HAP_EN_GPIO,
.hap_len_gpio = ISA1200_HAP_LEN_GPIO,
-#endif
.max_timeout = 15000,
.mode_ctrl = PWM_GEN_MODE,
.pwm_fd = {
@@ -2099,21 +1988,12 @@
ARRAY_SIZE(isl_charger_i2c_info),
},
#endif /* CONFIG_ISL9519_CHARGER */
-#ifndef MSM8930_PHASE_2
{
- I2C_LIQUID,
- MSM_8930_GSBI10_QUP_I2C_BUS_ID,
+ I2C_SURF | I2C_FFA | I2C_FLUID,
+ MSM_8930_GSBI9_QUP_I2C_BUS_ID,
msm_isa1200_board_info,
ARRAY_SIZE(msm_isa1200_board_info),
},
-#else
- {
- I2C_FFA | I2C_FLUID,
- MSM_8930_GSBI10_QUP_I2C_BUS_ID,
- msm_isa1200_board_info,
- ARRAY_SIZE(msm_isa1200_board_info),
- },
-#endif
{
I2C_SURF,
MSM_8930_GSBI3_QUP_I2C_BUS_ID,