sh: sh775x/titan fixes for irq header changes.
The following moves the creation of IPR interupts into setup-7750.c
and updates a few other things to make it all work after the "Drop
CPU subtype IRQ headers" commit. It boots and runs fine on my titan
board.
- adds an ipr_idx to the ipr_data and uses a function in the subtype
code to calculate the address of the IPR registers
- adds a function to enable individual interrupt mode for externals
in the subtype code and calls that from the titan board code
instead of doing it directly.
- I changed the shift in the ipr_data to be the actual # of bits to
shift, instead of the numnber / 4 - made it easier to match with
the manual.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
diff --git a/include/asm-sh/irq.h b/include/asm-sh/irq.h
index f10cfc1..fd57608 100644
--- a/include/asm-sh/irq.h
+++ b/include/asm-sh/irq.h
@@ -93,6 +93,12 @@
#define NR_IRQS (ONCHIP_NR_IRQS + PINT_NR_IRQS + OFFCHIP_NR_IRQS)
/*
+ * Convert back and forth between INTEVT and IRQ values.
+ */
+#define evt2irq(evt) (((evt) >> 5) - 16)
+#define irq2evt(irq) (((irq) + 16) << 5)
+
+/*
* Simple Mask Register Support
*/
extern void make_maskreg_irq(unsigned int irq);
@@ -103,18 +109,36 @@
*/
void init_IRQ_pint(void);
+/*
+ * The shift value is now the number of bits to shift, not the number of
+ * bits/4. This is to make it easier to read the value directly from the
+ * datasheets. The IPR address, addr, will be set from ipr_idx via the
+ * map_ipridx_to_addr function.
+ */
struct ipr_data {
unsigned int irq;
- unsigned int addr; /* Address of Interrupt Priority Register */
- int shift; /* Shifts of the 16-bit data */
+ int ipr_idx; /* Index for the IPR registered */
+ int shift; /* Number of bits to shift the data */
int priority; /* The priority */
+ unsigned int addr; /* Address of Interrupt Priority Register */
};
/*
+ * Given an IPR IDX, map the value to an IPR register address.
+ */
+unsigned int map_ipridx_to_addr(int idx);
+
+/*
+ * Enable individual interrupt mode for external IPR IRQs.
+ */
+void ipr_irq_enable_irlm(void);
+
+/*
* Function for "on chip support modules".
*/
-extern void make_ipr_irq(struct ipr_data *table, unsigned int nr_irqs);
-extern void make_imask_irq(unsigned int irq);
+void make_ipr_irq(struct ipr_data *table, unsigned int nr_irqs);
+void make_imask_irq(unsigned int irq);
+void init_IRQ_ipr(void);
struct intc2_data {
unsigned short irq;
diff --git a/include/asm-sh/titan.h b/include/asm-sh/titan.h
index 270a4f4..03f3583 100644
--- a/include/asm-sh/titan.h
+++ b/include/asm-sh/titan.h
@@ -1,9 +1,8 @@
/*
* Platform defintions for Titan
*/
-
-#ifndef _ASM_SH_TITAN_TITAN_H
-#define _ASM_SH_TITAN_TITAN_H
+#ifndef _ASM_SH_TITAN_H
+#define _ASM_SH_TITAN_H
#define __IO_PREFIX titan
#include <asm/io_generic.h>
@@ -15,29 +14,4 @@
#define TITAN_IRQ_MPCIB 11 /* mPCI B */
#define TITAN_IRQ_USB 11 /* USB */
-/*
- * The external interrupt lines, these take up ints 0 - 15 inclusive
- * depending on the priority for the interrupt. In fact the priority
- * is the interrupt :-)
- */
-#define IRL0_IRQ 0
-#define IRL0_IPR_ADDR INTC_IPRD
-#define IRL0_IPR_POS 3
-#define IRL0_PRIORITY 8
-
-#define IRL1_IRQ 1
-#define IRL1_IPR_ADDR INTC_IPRD
-#define IRL1_IPR_POS 2
-#define IRL1_PRIORITY 8
-
-#define IRL2_IRQ 2
-#define IRL2_IPR_ADDR INTC_IPRD
-#define IRL2_IPR_POS 1
-#define IRL2_PRIORITY 8
-
-#define IRL3_IRQ 3
-#define IRL3_IPR_ADDR INTC_IPRD
-#define IRL3_IPR_POS 0
-#define IRL3_PRIORITY 8
-
-#endif
+#endif /* __ASM_SH_TITAN_H */