|  | /* esp_scsi.c: ESP SCSI driver. | 
|  | * | 
|  | * Copyright (C) 2007 David S. Miller (davem@davemloft.net) | 
|  | */ | 
|  |  | 
|  | #include <linux/kernel.h> | 
|  | #include <linux/types.h> | 
|  | #include <linux/slab.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/list.h> | 
|  | #include <linux/completion.h> | 
|  | #include <linux/kallsyms.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/moduleparam.h> | 
|  | #include <linux/init.h> | 
|  | #include <linux/irqreturn.h> | 
|  |  | 
|  | #include <asm/irq.h> | 
|  | #include <asm/io.h> | 
|  | #include <asm/dma.h> | 
|  |  | 
|  | #include <scsi/scsi.h> | 
|  | #include <scsi/scsi_host.h> | 
|  | #include <scsi/scsi_cmnd.h> | 
|  | #include <scsi/scsi_device.h> | 
|  | #include <scsi/scsi_tcq.h> | 
|  | #include <scsi/scsi_dbg.h> | 
|  | #include <scsi/scsi_transport_spi.h> | 
|  |  | 
|  | #include "esp_scsi.h" | 
|  |  | 
|  | #define DRV_MODULE_NAME		"esp" | 
|  | #define PFX DRV_MODULE_NAME	": " | 
|  | #define DRV_VERSION		"2.000" | 
|  | #define DRV_MODULE_RELDATE	"April 19, 2007" | 
|  |  | 
|  | /* SCSI bus reset settle time in seconds.  */ | 
|  | static int esp_bus_reset_settle = 3; | 
|  |  | 
|  | static u32 esp_debug; | 
|  | #define ESP_DEBUG_INTR		0x00000001 | 
|  | #define ESP_DEBUG_SCSICMD	0x00000002 | 
|  | #define ESP_DEBUG_RESET		0x00000004 | 
|  | #define ESP_DEBUG_MSGIN		0x00000008 | 
|  | #define ESP_DEBUG_MSGOUT	0x00000010 | 
|  | #define ESP_DEBUG_CMDDONE	0x00000020 | 
|  | #define ESP_DEBUG_DISCONNECT	0x00000040 | 
|  | #define ESP_DEBUG_DATASTART	0x00000080 | 
|  | #define ESP_DEBUG_DATADONE	0x00000100 | 
|  | #define ESP_DEBUG_RECONNECT	0x00000200 | 
|  | #define ESP_DEBUG_AUTOSENSE	0x00000400 | 
|  |  | 
|  | #define esp_log_intr(f, a...) \ | 
|  | do {	if (esp_debug & ESP_DEBUG_INTR) \ | 
|  | printk(f, ## a); \ | 
|  | } while (0) | 
|  |  | 
|  | #define esp_log_reset(f, a...) \ | 
|  | do {	if (esp_debug & ESP_DEBUG_RESET) \ | 
|  | printk(f, ## a); \ | 
|  | } while (0) | 
|  |  | 
|  | #define esp_log_msgin(f, a...) \ | 
|  | do {	if (esp_debug & ESP_DEBUG_MSGIN) \ | 
|  | printk(f, ## a); \ | 
|  | } while (0) | 
|  |  | 
|  | #define esp_log_msgout(f, a...) \ | 
|  | do {	if (esp_debug & ESP_DEBUG_MSGOUT) \ | 
|  | printk(f, ## a); \ | 
|  | } while (0) | 
|  |  | 
|  | #define esp_log_cmddone(f, a...) \ | 
|  | do {	if (esp_debug & ESP_DEBUG_CMDDONE) \ | 
|  | printk(f, ## a); \ | 
|  | } while (0) | 
|  |  | 
|  | #define esp_log_disconnect(f, a...) \ | 
|  | do {	if (esp_debug & ESP_DEBUG_DISCONNECT) \ | 
|  | printk(f, ## a); \ | 
|  | } while (0) | 
|  |  | 
|  | #define esp_log_datastart(f, a...) \ | 
|  | do {	if (esp_debug & ESP_DEBUG_DATASTART) \ | 
|  | printk(f, ## a); \ | 
|  | } while (0) | 
|  |  | 
|  | #define esp_log_datadone(f, a...) \ | 
|  | do {	if (esp_debug & ESP_DEBUG_DATADONE) \ | 
|  | printk(f, ## a); \ | 
|  | } while (0) | 
|  |  | 
|  | #define esp_log_reconnect(f, a...) \ | 
|  | do {	if (esp_debug & ESP_DEBUG_RECONNECT) \ | 
|  | printk(f, ## a); \ | 
|  | } while (0) | 
|  |  | 
|  | #define esp_log_autosense(f, a...) \ | 
|  | do {	if (esp_debug & ESP_DEBUG_AUTOSENSE) \ | 
|  | printk(f, ## a); \ | 
|  | } while (0) | 
|  |  | 
|  | #define esp_read8(REG)		esp->ops->esp_read8(esp, REG) | 
|  | #define esp_write8(VAL,REG)	esp->ops->esp_write8(esp, VAL, REG) | 
|  |  | 
|  | static void esp_log_fill_regs(struct esp *esp, | 
|  | struct esp_event_ent *p) | 
|  | { | 
|  | p->sreg = esp->sreg; | 
|  | p->seqreg = esp->seqreg; | 
|  | p->sreg2 = esp->sreg2; | 
|  | p->ireg = esp->ireg; | 
|  | p->select_state = esp->select_state; | 
|  | p->event = esp->event; | 
|  | } | 
|  |  | 
|  | void scsi_esp_cmd(struct esp *esp, u8 val) | 
|  | { | 
|  | struct esp_event_ent *p; | 
|  | int idx = esp->esp_event_cur; | 
|  |  | 
|  | p = &esp->esp_event_log[idx]; | 
|  | p->type = ESP_EVENT_TYPE_CMD; | 
|  | p->val = val; | 
|  | esp_log_fill_regs(esp, p); | 
|  |  | 
|  | esp->esp_event_cur = (idx + 1) & (ESP_EVENT_LOG_SZ - 1); | 
|  |  | 
|  | esp_write8(val, ESP_CMD); | 
|  | } | 
|  | EXPORT_SYMBOL(scsi_esp_cmd); | 
|  |  | 
|  | static void esp_event(struct esp *esp, u8 val) | 
|  | { | 
|  | struct esp_event_ent *p; | 
|  | int idx = esp->esp_event_cur; | 
|  |  | 
|  | p = &esp->esp_event_log[idx]; | 
|  | p->type = ESP_EVENT_TYPE_EVENT; | 
|  | p->val = val; | 
|  | esp_log_fill_regs(esp, p); | 
|  |  | 
|  | esp->esp_event_cur = (idx + 1) & (ESP_EVENT_LOG_SZ - 1); | 
|  |  | 
|  | esp->event = val; | 
|  | } | 
|  |  | 
|  | static void esp_dump_cmd_log(struct esp *esp) | 
|  | { | 
|  | int idx = esp->esp_event_cur; | 
|  | int stop = idx; | 
|  |  | 
|  | printk(KERN_INFO PFX "esp%d: Dumping command log\n", | 
|  | esp->host->unique_id); | 
|  | do { | 
|  | struct esp_event_ent *p = &esp->esp_event_log[idx]; | 
|  |  | 
|  | printk(KERN_INFO PFX "esp%d: ent[%d] %s ", | 
|  | esp->host->unique_id, idx, | 
|  | p->type == ESP_EVENT_TYPE_CMD ? "CMD" : "EVENT"); | 
|  |  | 
|  | printk("val[%02x] sreg[%02x] seqreg[%02x] " | 
|  | "sreg2[%02x] ireg[%02x] ss[%02x] event[%02x]\n", | 
|  | p->val, p->sreg, p->seqreg, | 
|  | p->sreg2, p->ireg, p->select_state, p->event); | 
|  |  | 
|  | idx = (idx + 1) & (ESP_EVENT_LOG_SZ - 1); | 
|  | } while (idx != stop); | 
|  | } | 
|  |  | 
|  | static void esp_flush_fifo(struct esp *esp) | 
|  | { | 
|  | scsi_esp_cmd(esp, ESP_CMD_FLUSH); | 
|  | if (esp->rev == ESP236) { | 
|  | int lim = 1000; | 
|  |  | 
|  | while (esp_read8(ESP_FFLAGS) & ESP_FF_FBYTES) { | 
|  | if (--lim == 0) { | 
|  | printk(KERN_ALERT PFX "esp%d: ESP_FF_BYTES " | 
|  | "will not clear!\n", | 
|  | esp->host->unique_id); | 
|  | break; | 
|  | } | 
|  | udelay(1); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static void hme_read_fifo(struct esp *esp) | 
|  | { | 
|  | int fcnt = esp_read8(ESP_FFLAGS) & ESP_FF_FBYTES; | 
|  | int idx = 0; | 
|  |  | 
|  | while (fcnt--) { | 
|  | esp->fifo[idx++] = esp_read8(ESP_FDATA); | 
|  | esp->fifo[idx++] = esp_read8(ESP_FDATA); | 
|  | } | 
|  | if (esp->sreg2 & ESP_STAT2_F1BYTE) { | 
|  | esp_write8(0, ESP_FDATA); | 
|  | esp->fifo[idx++] = esp_read8(ESP_FDATA); | 
|  | scsi_esp_cmd(esp, ESP_CMD_FLUSH); | 
|  | } | 
|  | esp->fifo_cnt = idx; | 
|  | } | 
|  |  | 
|  | static void esp_set_all_config3(struct esp *esp, u8 val) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i < ESP_MAX_TARGET; i++) | 
|  | esp->target[i].esp_config3 = val; | 
|  | } | 
|  |  | 
|  | /* Reset the ESP chip, _not_ the SCSI bus. */ | 
|  | static void esp_reset_esp(struct esp *esp) | 
|  | { | 
|  | u8 family_code, version; | 
|  |  | 
|  | /* Now reset the ESP chip */ | 
|  | scsi_esp_cmd(esp, ESP_CMD_RC); | 
|  | scsi_esp_cmd(esp, ESP_CMD_NULL | ESP_CMD_DMA); | 
|  | if (esp->rev == FAST) | 
|  | esp_write8(ESP_CONFIG2_FENAB, ESP_CFG2); | 
|  | scsi_esp_cmd(esp, ESP_CMD_NULL | ESP_CMD_DMA); | 
|  |  | 
|  | /* This is the only point at which it is reliable to read | 
|  | * the ID-code for a fast ESP chip variants. | 
|  | */ | 
|  | esp->max_period = ((35 * esp->ccycle) / 1000); | 
|  | if (esp->rev == FAST) { | 
|  | version = esp_read8(ESP_UID); | 
|  | family_code = (version & 0xf8) >> 3; | 
|  | if (family_code == 0x02) | 
|  | esp->rev = FAS236; | 
|  | else if (family_code == 0x0a) | 
|  | esp->rev = FASHME; /* Version is usually '5'. */ | 
|  | else | 
|  | esp->rev = FAS100A; | 
|  | esp->min_period = ((4 * esp->ccycle) / 1000); | 
|  | } else { | 
|  | esp->min_period = ((5 * esp->ccycle) / 1000); | 
|  | } | 
|  | esp->max_period = (esp->max_period + 3)>>2; | 
|  | esp->min_period = (esp->min_period + 3)>>2; | 
|  |  | 
|  | esp_write8(esp->config1, ESP_CFG1); | 
|  | switch (esp->rev) { | 
|  | case ESP100: | 
|  | /* nothing to do */ | 
|  | break; | 
|  |  | 
|  | case ESP100A: | 
|  | esp_write8(esp->config2, ESP_CFG2); | 
|  | break; | 
|  |  | 
|  | case ESP236: | 
|  | /* Slow 236 */ | 
|  | esp_write8(esp->config2, ESP_CFG2); | 
|  | esp->prev_cfg3 = esp->target[0].esp_config3; | 
|  | esp_write8(esp->prev_cfg3, ESP_CFG3); | 
|  | break; | 
|  |  | 
|  | case FASHME: | 
|  | esp->config2 |= (ESP_CONFIG2_HME32 | ESP_CONFIG2_HMEFENAB); | 
|  | /* fallthrough... */ | 
|  |  | 
|  | case FAS236: | 
|  | /* Fast 236 or HME */ | 
|  | esp_write8(esp->config2, ESP_CFG2); | 
|  | if (esp->rev == FASHME) { | 
|  | u8 cfg3 = esp->target[0].esp_config3; | 
|  |  | 
|  | cfg3 |= ESP_CONFIG3_FCLOCK | ESP_CONFIG3_OBPUSH; | 
|  | if (esp->scsi_id >= 8) | 
|  | cfg3 |= ESP_CONFIG3_IDBIT3; | 
|  | esp_set_all_config3(esp, cfg3); | 
|  | } else { | 
|  | u32 cfg3 = esp->target[0].esp_config3; | 
|  |  | 
|  | cfg3 |= ESP_CONFIG3_FCLK; | 
|  | esp_set_all_config3(esp, cfg3); | 
|  | } | 
|  | esp->prev_cfg3 = esp->target[0].esp_config3; | 
|  | esp_write8(esp->prev_cfg3, ESP_CFG3); | 
|  | if (esp->rev == FASHME) { | 
|  | esp->radelay = 80; | 
|  | } else { | 
|  | if (esp->flags & ESP_FLAG_DIFFERENTIAL) | 
|  | esp->radelay = 0; | 
|  | else | 
|  | esp->radelay = 96; | 
|  | } | 
|  | break; | 
|  |  | 
|  | case FAS100A: | 
|  | /* Fast 100a */ | 
|  | esp_write8(esp->config2, ESP_CFG2); | 
|  | esp_set_all_config3(esp, | 
|  | (esp->target[0].esp_config3 | | 
|  | ESP_CONFIG3_FCLOCK)); | 
|  | esp->prev_cfg3 = esp->target[0].esp_config3; | 
|  | esp_write8(esp->prev_cfg3, ESP_CFG3); | 
|  | esp->radelay = 32; | 
|  | break; | 
|  |  | 
|  | default: | 
|  | break; | 
|  | } | 
|  |  | 
|  | /* Reload the configuration registers */ | 
|  | esp_write8(esp->cfact, ESP_CFACT); | 
|  |  | 
|  | esp->prev_stp = 0; | 
|  | esp_write8(esp->prev_stp, ESP_STP); | 
|  |  | 
|  | esp->prev_soff = 0; | 
|  | esp_write8(esp->prev_soff, ESP_SOFF); | 
|  |  | 
|  | esp_write8(esp->neg_defp, ESP_TIMEO); | 
|  |  | 
|  | /* Eat any bitrot in the chip */ | 
|  | esp_read8(ESP_INTRPT); | 
|  | udelay(100); | 
|  | } | 
|  |  | 
|  | static void esp_map_dma(struct esp *esp, struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct esp_cmd_priv *spriv = ESP_CMD_PRIV(cmd); | 
|  | struct scatterlist *sg = scsi_sglist(cmd); | 
|  | int dir = cmd->sc_data_direction; | 
|  | int total, i; | 
|  |  | 
|  | if (dir == DMA_NONE) | 
|  | return; | 
|  |  | 
|  | spriv->u.num_sg = esp->ops->map_sg(esp, sg, scsi_sg_count(cmd), dir); | 
|  | spriv->cur_residue = sg_dma_len(sg); | 
|  | spriv->cur_sg = sg; | 
|  |  | 
|  | total = 0; | 
|  | for (i = 0; i < spriv->u.num_sg; i++) | 
|  | total += sg_dma_len(&sg[i]); | 
|  | spriv->tot_residue = total; | 
|  | } | 
|  |  | 
|  | static dma_addr_t esp_cur_dma_addr(struct esp_cmd_entry *ent, | 
|  | struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct esp_cmd_priv *p = ESP_CMD_PRIV(cmd); | 
|  |  | 
|  | if (ent->flags & ESP_CMD_FLAG_AUTOSENSE) { | 
|  | return ent->sense_dma + | 
|  | (ent->sense_ptr - cmd->sense_buffer); | 
|  | } | 
|  |  | 
|  | return sg_dma_address(p->cur_sg) + | 
|  | (sg_dma_len(p->cur_sg) - | 
|  | p->cur_residue); | 
|  | } | 
|  |  | 
|  | static unsigned int esp_cur_dma_len(struct esp_cmd_entry *ent, | 
|  | struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct esp_cmd_priv *p = ESP_CMD_PRIV(cmd); | 
|  |  | 
|  | if (ent->flags & ESP_CMD_FLAG_AUTOSENSE) { | 
|  | return SCSI_SENSE_BUFFERSIZE - | 
|  | (ent->sense_ptr - cmd->sense_buffer); | 
|  | } | 
|  | return p->cur_residue; | 
|  | } | 
|  |  | 
|  | static void esp_advance_dma(struct esp *esp, struct esp_cmd_entry *ent, | 
|  | struct scsi_cmnd *cmd, unsigned int len) | 
|  | { | 
|  | struct esp_cmd_priv *p = ESP_CMD_PRIV(cmd); | 
|  |  | 
|  | if (ent->flags & ESP_CMD_FLAG_AUTOSENSE) { | 
|  | ent->sense_ptr += len; | 
|  | return; | 
|  | } | 
|  |  | 
|  | p->cur_residue -= len; | 
|  | p->tot_residue -= len; | 
|  | if (p->cur_residue < 0 || p->tot_residue < 0) { | 
|  | printk(KERN_ERR PFX "esp%d: Data transfer overflow.\n", | 
|  | esp->host->unique_id); | 
|  | printk(KERN_ERR PFX "esp%d: cur_residue[%d] tot_residue[%d] " | 
|  | "len[%u]\n", | 
|  | esp->host->unique_id, | 
|  | p->cur_residue, p->tot_residue, len); | 
|  | p->cur_residue = 0; | 
|  | p->tot_residue = 0; | 
|  | } | 
|  | if (!p->cur_residue && p->tot_residue) { | 
|  | p->cur_sg++; | 
|  | p->cur_residue = sg_dma_len(p->cur_sg); | 
|  | } | 
|  | } | 
|  |  | 
|  | static void esp_unmap_dma(struct esp *esp, struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct esp_cmd_priv *spriv = ESP_CMD_PRIV(cmd); | 
|  | int dir = cmd->sc_data_direction; | 
|  |  | 
|  | if (dir == DMA_NONE) | 
|  | return; | 
|  |  | 
|  | esp->ops->unmap_sg(esp, scsi_sglist(cmd), spriv->u.num_sg, dir); | 
|  | } | 
|  |  | 
|  | static void esp_save_pointers(struct esp *esp, struct esp_cmd_entry *ent) | 
|  | { | 
|  | struct scsi_cmnd *cmd = ent->cmd; | 
|  | struct esp_cmd_priv *spriv = ESP_CMD_PRIV(cmd); | 
|  |  | 
|  | if (ent->flags & ESP_CMD_FLAG_AUTOSENSE) { | 
|  | ent->saved_sense_ptr = ent->sense_ptr; | 
|  | return; | 
|  | } | 
|  | ent->saved_cur_residue = spriv->cur_residue; | 
|  | ent->saved_cur_sg = spriv->cur_sg; | 
|  | ent->saved_tot_residue = spriv->tot_residue; | 
|  | } | 
|  |  | 
|  | static void esp_restore_pointers(struct esp *esp, struct esp_cmd_entry *ent) | 
|  | { | 
|  | struct scsi_cmnd *cmd = ent->cmd; | 
|  | struct esp_cmd_priv *spriv = ESP_CMD_PRIV(cmd); | 
|  |  | 
|  | if (ent->flags & ESP_CMD_FLAG_AUTOSENSE) { | 
|  | ent->sense_ptr = ent->saved_sense_ptr; | 
|  | return; | 
|  | } | 
|  | spriv->cur_residue = ent->saved_cur_residue; | 
|  | spriv->cur_sg = ent->saved_cur_sg; | 
|  | spriv->tot_residue = ent->saved_tot_residue; | 
|  | } | 
|  |  | 
|  | static void esp_check_command_len(struct esp *esp, struct scsi_cmnd *cmd) | 
|  | { | 
|  | if (cmd->cmd_len == 6 || | 
|  | cmd->cmd_len == 10 || | 
|  | cmd->cmd_len == 12) { | 
|  | esp->flags &= ~ESP_FLAG_DOING_SLOWCMD; | 
|  | } else { | 
|  | esp->flags |= ESP_FLAG_DOING_SLOWCMD; | 
|  | } | 
|  | } | 
|  |  | 
|  | static void esp_write_tgt_config3(struct esp *esp, int tgt) | 
|  | { | 
|  | if (esp->rev > ESP100A) { | 
|  | u8 val = esp->target[tgt].esp_config3; | 
|  |  | 
|  | if (val != esp->prev_cfg3) { | 
|  | esp->prev_cfg3 = val; | 
|  | esp_write8(val, ESP_CFG3); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static void esp_write_tgt_sync(struct esp *esp, int tgt) | 
|  | { | 
|  | u8 off = esp->target[tgt].esp_offset; | 
|  | u8 per = esp->target[tgt].esp_period; | 
|  |  | 
|  | if (off != esp->prev_soff) { | 
|  | esp->prev_soff = off; | 
|  | esp_write8(off, ESP_SOFF); | 
|  | } | 
|  | if (per != esp->prev_stp) { | 
|  | esp->prev_stp = per; | 
|  | esp_write8(per, ESP_STP); | 
|  | } | 
|  | } | 
|  |  | 
|  | static u32 esp_dma_length_limit(struct esp *esp, u32 dma_addr, u32 dma_len) | 
|  | { | 
|  | if (esp->rev == FASHME) { | 
|  | /* Arbitrary segment boundaries, 24-bit counts.  */ | 
|  | if (dma_len > (1U << 24)) | 
|  | dma_len = (1U << 24); | 
|  | } else { | 
|  | u32 base, end; | 
|  |  | 
|  | /* ESP chip limits other variants by 16-bits of transfer | 
|  | * count.  Actually on FAS100A and FAS236 we could get | 
|  | * 24-bits of transfer count by enabling ESP_CONFIG2_FENAB | 
|  | * in the ESP_CFG2 register but that causes other unwanted | 
|  | * changes so we don't use it currently. | 
|  | */ | 
|  | if (dma_len > (1U << 16)) | 
|  | dma_len = (1U << 16); | 
|  |  | 
|  | /* All of the DMA variants hooked up to these chips | 
|  | * cannot handle crossing a 24-bit address boundary. | 
|  | */ | 
|  | base = dma_addr & ((1U << 24) - 1U); | 
|  | end = base + dma_len; | 
|  | if (end > (1U << 24)) | 
|  | end = (1U <<24); | 
|  | dma_len = end - base; | 
|  | } | 
|  | return dma_len; | 
|  | } | 
|  |  | 
|  | static int esp_need_to_nego_wide(struct esp_target_data *tp) | 
|  | { | 
|  | struct scsi_target *target = tp->starget; | 
|  |  | 
|  | return spi_width(target) != tp->nego_goal_width; | 
|  | } | 
|  |  | 
|  | static int esp_need_to_nego_sync(struct esp_target_data *tp) | 
|  | { | 
|  | struct scsi_target *target = tp->starget; | 
|  |  | 
|  | /* When offset is zero, period is "don't care".  */ | 
|  | if (!spi_offset(target) && !tp->nego_goal_offset) | 
|  | return 0; | 
|  |  | 
|  | if (spi_offset(target) == tp->nego_goal_offset && | 
|  | spi_period(target) == tp->nego_goal_period) | 
|  | return 0; | 
|  |  | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static int esp_alloc_lun_tag(struct esp_cmd_entry *ent, | 
|  | struct esp_lun_data *lp) | 
|  | { | 
|  | if (!ent->tag[0]) { | 
|  | /* Non-tagged, slot already taken?  */ | 
|  | if (lp->non_tagged_cmd) | 
|  | return -EBUSY; | 
|  |  | 
|  | if (lp->hold) { | 
|  | /* We are being held by active tagged | 
|  | * commands. | 
|  | */ | 
|  | if (lp->num_tagged) | 
|  | return -EBUSY; | 
|  |  | 
|  | /* Tagged commands completed, we can unplug | 
|  | * the queue and run this untagged command. | 
|  | */ | 
|  | lp->hold = 0; | 
|  | } else if (lp->num_tagged) { | 
|  | /* Plug the queue until num_tagged decreases | 
|  | * to zero in esp_free_lun_tag. | 
|  | */ | 
|  | lp->hold = 1; | 
|  | return -EBUSY; | 
|  | } | 
|  |  | 
|  | lp->non_tagged_cmd = ent; | 
|  | return 0; | 
|  | } else { | 
|  | /* Tagged command, see if blocked by a | 
|  | * non-tagged one. | 
|  | */ | 
|  | if (lp->non_tagged_cmd || lp->hold) | 
|  | return -EBUSY; | 
|  | } | 
|  |  | 
|  | BUG_ON(lp->tagged_cmds[ent->tag[1]]); | 
|  |  | 
|  | lp->tagged_cmds[ent->tag[1]] = ent; | 
|  | lp->num_tagged++; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void esp_free_lun_tag(struct esp_cmd_entry *ent, | 
|  | struct esp_lun_data *lp) | 
|  | { | 
|  | if (ent->tag[0]) { | 
|  | BUG_ON(lp->tagged_cmds[ent->tag[1]] != ent); | 
|  | lp->tagged_cmds[ent->tag[1]] = NULL; | 
|  | lp->num_tagged--; | 
|  | } else { | 
|  | BUG_ON(lp->non_tagged_cmd != ent); | 
|  | lp->non_tagged_cmd = NULL; | 
|  | } | 
|  | } | 
|  |  | 
|  | /* When a contingent allegiance conditon is created, we force feed a | 
|  | * REQUEST_SENSE command to the device to fetch the sense data.  I | 
|  | * tried many other schemes, relying on the scsi error handling layer | 
|  | * to send out the REQUEST_SENSE automatically, but this was difficult | 
|  | * to get right especially in the presence of applications like smartd | 
|  | * which use SG_IO to send out their own REQUEST_SENSE commands. | 
|  | */ | 
|  | static void esp_autosense(struct esp *esp, struct esp_cmd_entry *ent) | 
|  | { | 
|  | struct scsi_cmnd *cmd = ent->cmd; | 
|  | struct scsi_device *dev = cmd->device; | 
|  | int tgt, lun; | 
|  | u8 *p, val; | 
|  |  | 
|  | tgt = dev->id; | 
|  | lun = dev->lun; | 
|  |  | 
|  |  | 
|  | if (!ent->sense_ptr) { | 
|  | esp_log_autosense("esp%d: Doing auto-sense for " | 
|  | "tgt[%d] lun[%d]\n", | 
|  | esp->host->unique_id, tgt, lun); | 
|  |  | 
|  | ent->sense_ptr = cmd->sense_buffer; | 
|  | ent->sense_dma = esp->ops->map_single(esp, | 
|  | ent->sense_ptr, | 
|  | SCSI_SENSE_BUFFERSIZE, | 
|  | DMA_FROM_DEVICE); | 
|  | } | 
|  | ent->saved_sense_ptr = ent->sense_ptr; | 
|  |  | 
|  | esp->active_cmd = ent; | 
|  |  | 
|  | p = esp->command_block; | 
|  | esp->msg_out_len = 0; | 
|  |  | 
|  | *p++ = IDENTIFY(0, lun); | 
|  | *p++ = REQUEST_SENSE; | 
|  | *p++ = ((dev->scsi_level <= SCSI_2) ? | 
|  | (lun << 5) : 0); | 
|  | *p++ = 0; | 
|  | *p++ = 0; | 
|  | *p++ = SCSI_SENSE_BUFFERSIZE; | 
|  | *p++ = 0; | 
|  |  | 
|  | esp->select_state = ESP_SELECT_BASIC; | 
|  |  | 
|  | val = tgt; | 
|  | if (esp->rev == FASHME) | 
|  | val |= ESP_BUSID_RESELID | ESP_BUSID_CTR32BIT; | 
|  | esp_write8(val, ESP_BUSID); | 
|  |  | 
|  | esp_write_tgt_sync(esp, tgt); | 
|  | esp_write_tgt_config3(esp, tgt); | 
|  |  | 
|  | val = (p - esp->command_block); | 
|  |  | 
|  | if (esp->rev == FASHME) | 
|  | scsi_esp_cmd(esp, ESP_CMD_FLUSH); | 
|  | esp->ops->send_dma_cmd(esp, esp->command_block_dma, | 
|  | val, 16, 0, ESP_CMD_DMA | ESP_CMD_SELA); | 
|  | } | 
|  |  | 
|  | static struct esp_cmd_entry *find_and_prep_issuable_command(struct esp *esp) | 
|  | { | 
|  | struct esp_cmd_entry *ent; | 
|  |  | 
|  | list_for_each_entry(ent, &esp->queued_cmds, list) { | 
|  | struct scsi_cmnd *cmd = ent->cmd; | 
|  | struct scsi_device *dev = cmd->device; | 
|  | struct esp_lun_data *lp = dev->hostdata; | 
|  |  | 
|  | if (ent->flags & ESP_CMD_FLAG_AUTOSENSE) { | 
|  | ent->tag[0] = 0; | 
|  | ent->tag[1] = 0; | 
|  | return ent; | 
|  | } | 
|  |  | 
|  | if (!scsi_populate_tag_msg(cmd, &ent->tag[0])) { | 
|  | ent->tag[0] = 0; | 
|  | ent->tag[1] = 0; | 
|  | } | 
|  |  | 
|  | if (esp_alloc_lun_tag(ent, lp) < 0) | 
|  | continue; | 
|  |  | 
|  | return ent; | 
|  | } | 
|  |  | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | static void esp_maybe_execute_command(struct esp *esp) | 
|  | { | 
|  | struct esp_target_data *tp; | 
|  | struct esp_lun_data *lp; | 
|  | struct scsi_device *dev; | 
|  | struct scsi_cmnd *cmd; | 
|  | struct esp_cmd_entry *ent; | 
|  | int tgt, lun, i; | 
|  | u32 val, start_cmd; | 
|  | u8 *p; | 
|  |  | 
|  | if (esp->active_cmd || | 
|  | (esp->flags & ESP_FLAG_RESETTING)) | 
|  | return; | 
|  |  | 
|  | ent = find_and_prep_issuable_command(esp); | 
|  | if (!ent) | 
|  | return; | 
|  |  | 
|  | if (ent->flags & ESP_CMD_FLAG_AUTOSENSE) { | 
|  | esp_autosense(esp, ent); | 
|  | return; | 
|  | } | 
|  |  | 
|  | cmd = ent->cmd; | 
|  | dev = cmd->device; | 
|  | tgt = dev->id; | 
|  | lun = dev->lun; | 
|  | tp = &esp->target[tgt]; | 
|  | lp = dev->hostdata; | 
|  |  | 
|  | list_del(&ent->list); | 
|  | list_add(&ent->list, &esp->active_cmds); | 
|  |  | 
|  | esp->active_cmd = ent; | 
|  |  | 
|  | esp_map_dma(esp, cmd); | 
|  | esp_save_pointers(esp, ent); | 
|  |  | 
|  | esp_check_command_len(esp, cmd); | 
|  |  | 
|  | p = esp->command_block; | 
|  |  | 
|  | esp->msg_out_len = 0; | 
|  | if (tp->flags & ESP_TGT_CHECK_NEGO) { | 
|  | /* Need to negotiate.  If the target is broken | 
|  | * go for synchronous transfers and non-wide. | 
|  | */ | 
|  | if (tp->flags & ESP_TGT_BROKEN) { | 
|  | tp->flags &= ~ESP_TGT_DISCONNECT; | 
|  | tp->nego_goal_period = 0; | 
|  | tp->nego_goal_offset = 0; | 
|  | tp->nego_goal_width = 0; | 
|  | tp->nego_goal_tags = 0; | 
|  | } | 
|  |  | 
|  | /* If the settings are not changing, skip this.  */ | 
|  | if (spi_width(tp->starget) == tp->nego_goal_width && | 
|  | spi_period(tp->starget) == tp->nego_goal_period && | 
|  | spi_offset(tp->starget) == tp->nego_goal_offset) { | 
|  | tp->flags &= ~ESP_TGT_CHECK_NEGO; | 
|  | goto build_identify; | 
|  | } | 
|  |  | 
|  | if (esp->rev == FASHME && esp_need_to_nego_wide(tp)) { | 
|  | esp->msg_out_len = | 
|  | spi_populate_width_msg(&esp->msg_out[0], | 
|  | (tp->nego_goal_width ? | 
|  | 1 : 0)); | 
|  | tp->flags |= ESP_TGT_NEGO_WIDE; | 
|  | } else if (esp_need_to_nego_sync(tp)) { | 
|  | esp->msg_out_len = | 
|  | spi_populate_sync_msg(&esp->msg_out[0], | 
|  | tp->nego_goal_period, | 
|  | tp->nego_goal_offset); | 
|  | tp->flags |= ESP_TGT_NEGO_SYNC; | 
|  | } else { | 
|  | tp->flags &= ~ESP_TGT_CHECK_NEGO; | 
|  | } | 
|  |  | 
|  | /* Process it like a slow command.  */ | 
|  | if (tp->flags & (ESP_TGT_NEGO_WIDE | ESP_TGT_NEGO_SYNC)) | 
|  | esp->flags |= ESP_FLAG_DOING_SLOWCMD; | 
|  | } | 
|  |  | 
|  | build_identify: | 
|  | /* If we don't have a lun-data struct yet, we're probing | 
|  | * so do not disconnect.  Also, do not disconnect unless | 
|  | * we have a tag on this command. | 
|  | */ | 
|  | if (lp && (tp->flags & ESP_TGT_DISCONNECT) && ent->tag[0]) | 
|  | *p++ = IDENTIFY(1, lun); | 
|  | else | 
|  | *p++ = IDENTIFY(0, lun); | 
|  |  | 
|  | if (ent->tag[0] && esp->rev == ESP100) { | 
|  | /* ESP100 lacks select w/atn3 command, use select | 
|  | * and stop instead. | 
|  | */ | 
|  | esp->flags |= ESP_FLAG_DOING_SLOWCMD; | 
|  | } | 
|  |  | 
|  | if (!(esp->flags & ESP_FLAG_DOING_SLOWCMD)) { | 
|  | start_cmd = ESP_CMD_DMA | ESP_CMD_SELA; | 
|  | if (ent->tag[0]) { | 
|  | *p++ = ent->tag[0]; | 
|  | *p++ = ent->tag[1]; | 
|  |  | 
|  | start_cmd = ESP_CMD_DMA | ESP_CMD_SA3; | 
|  | } | 
|  |  | 
|  | for (i = 0; i < cmd->cmd_len; i++) | 
|  | *p++ = cmd->cmnd[i]; | 
|  |  | 
|  | esp->select_state = ESP_SELECT_BASIC; | 
|  | } else { | 
|  | esp->cmd_bytes_left = cmd->cmd_len; | 
|  | esp->cmd_bytes_ptr = &cmd->cmnd[0]; | 
|  |  | 
|  | if (ent->tag[0]) { | 
|  | for (i = esp->msg_out_len - 1; | 
|  | i >= 0; i--) | 
|  | esp->msg_out[i + 2] = esp->msg_out[i]; | 
|  | esp->msg_out[0] = ent->tag[0]; | 
|  | esp->msg_out[1] = ent->tag[1]; | 
|  | esp->msg_out_len += 2; | 
|  | } | 
|  |  | 
|  | start_cmd = ESP_CMD_DMA | ESP_CMD_SELAS; | 
|  | esp->select_state = ESP_SELECT_MSGOUT; | 
|  | } | 
|  | val = tgt; | 
|  | if (esp->rev == FASHME) | 
|  | val |= ESP_BUSID_RESELID | ESP_BUSID_CTR32BIT; | 
|  | esp_write8(val, ESP_BUSID); | 
|  |  | 
|  | esp_write_tgt_sync(esp, tgt); | 
|  | esp_write_tgt_config3(esp, tgt); | 
|  |  | 
|  | val = (p - esp->command_block); | 
|  |  | 
|  | if (esp_debug & ESP_DEBUG_SCSICMD) { | 
|  | printk("ESP: tgt[%d] lun[%d] scsi_cmd [ ", tgt, lun); | 
|  | for (i = 0; i < cmd->cmd_len; i++) | 
|  | printk("%02x ", cmd->cmnd[i]); | 
|  | printk("]\n"); | 
|  | } | 
|  |  | 
|  | if (esp->rev == FASHME) | 
|  | scsi_esp_cmd(esp, ESP_CMD_FLUSH); | 
|  | esp->ops->send_dma_cmd(esp, esp->command_block_dma, | 
|  | val, 16, 0, start_cmd); | 
|  | } | 
|  |  | 
|  | static struct esp_cmd_entry *esp_get_ent(struct esp *esp) | 
|  | { | 
|  | struct list_head *head = &esp->esp_cmd_pool; | 
|  | struct esp_cmd_entry *ret; | 
|  |  | 
|  | if (list_empty(head)) { | 
|  | ret = kzalloc(sizeof(struct esp_cmd_entry), GFP_ATOMIC); | 
|  | } else { | 
|  | ret = list_entry(head->next, struct esp_cmd_entry, list); | 
|  | list_del(&ret->list); | 
|  | memset(ret, 0, sizeof(*ret)); | 
|  | } | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static void esp_put_ent(struct esp *esp, struct esp_cmd_entry *ent) | 
|  | { | 
|  | list_add(&ent->list, &esp->esp_cmd_pool); | 
|  | } | 
|  |  | 
|  | static void esp_cmd_is_done(struct esp *esp, struct esp_cmd_entry *ent, | 
|  | struct scsi_cmnd *cmd, unsigned int result) | 
|  | { | 
|  | struct scsi_device *dev = cmd->device; | 
|  | int tgt = dev->id; | 
|  | int lun = dev->lun; | 
|  |  | 
|  | esp->active_cmd = NULL; | 
|  | esp_unmap_dma(esp, cmd); | 
|  | esp_free_lun_tag(ent, dev->hostdata); | 
|  | cmd->result = result; | 
|  |  | 
|  | if (ent->eh_done) { | 
|  | complete(ent->eh_done); | 
|  | ent->eh_done = NULL; | 
|  | } | 
|  |  | 
|  | if (ent->flags & ESP_CMD_FLAG_AUTOSENSE) { | 
|  | esp->ops->unmap_single(esp, ent->sense_dma, | 
|  | SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); | 
|  | ent->sense_ptr = NULL; | 
|  |  | 
|  | /* Restore the message/status bytes to what we actually | 
|  | * saw originally.  Also, report that we are providing | 
|  | * the sense data. | 
|  | */ | 
|  | cmd->result = ((DRIVER_SENSE << 24) | | 
|  | (DID_OK << 16) | | 
|  | (COMMAND_COMPLETE << 8) | | 
|  | (SAM_STAT_CHECK_CONDITION << 0)); | 
|  |  | 
|  | ent->flags &= ~ESP_CMD_FLAG_AUTOSENSE; | 
|  | if (esp_debug & ESP_DEBUG_AUTOSENSE) { | 
|  | int i; | 
|  |  | 
|  | printk("esp%d: tgt[%d] lun[%d] AUTO SENSE[ ", | 
|  | esp->host->unique_id, tgt, lun); | 
|  | for (i = 0; i < 18; i++) | 
|  | printk("%02x ", cmd->sense_buffer[i]); | 
|  | printk("]\n"); | 
|  | } | 
|  | } | 
|  |  | 
|  | cmd->scsi_done(cmd); | 
|  |  | 
|  | list_del(&ent->list); | 
|  | esp_put_ent(esp, ent); | 
|  |  | 
|  | esp_maybe_execute_command(esp); | 
|  | } | 
|  |  | 
|  | static unsigned int compose_result(unsigned int status, unsigned int message, | 
|  | unsigned int driver_code) | 
|  | { | 
|  | return (status | (message << 8) | (driver_code << 16)); | 
|  | } | 
|  |  | 
|  | static void esp_event_queue_full(struct esp *esp, struct esp_cmd_entry *ent) | 
|  | { | 
|  | struct scsi_device *dev = ent->cmd->device; | 
|  | struct esp_lun_data *lp = dev->hostdata; | 
|  |  | 
|  | scsi_track_queue_full(dev, lp->num_tagged - 1); | 
|  | } | 
|  |  | 
|  | static int esp_queuecommand_lck(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *)) | 
|  | { | 
|  | struct scsi_device *dev = cmd->device; | 
|  | struct esp *esp = shost_priv(dev->host); | 
|  | struct esp_cmd_priv *spriv; | 
|  | struct esp_cmd_entry *ent; | 
|  |  | 
|  | ent = esp_get_ent(esp); | 
|  | if (!ent) | 
|  | return SCSI_MLQUEUE_HOST_BUSY; | 
|  |  | 
|  | ent->cmd = cmd; | 
|  |  | 
|  | cmd->scsi_done = done; | 
|  |  | 
|  | spriv = ESP_CMD_PRIV(cmd); | 
|  | spriv->u.dma_addr = ~(dma_addr_t)0x0; | 
|  |  | 
|  | list_add_tail(&ent->list, &esp->queued_cmds); | 
|  |  | 
|  | esp_maybe_execute_command(esp); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static DEF_SCSI_QCMD(esp_queuecommand) | 
|  |  | 
|  | static int esp_check_gross_error(struct esp *esp) | 
|  | { | 
|  | if (esp->sreg & ESP_STAT_SPAM) { | 
|  | /* Gross Error, could be one of: | 
|  | * - top of fifo overwritten | 
|  | * - top of command register overwritten | 
|  | * - DMA programmed with wrong direction | 
|  | * - improper phase change | 
|  | */ | 
|  | printk(KERN_ERR PFX "esp%d: Gross error sreg[%02x]\n", | 
|  | esp->host->unique_id, esp->sreg); | 
|  | /* XXX Reset the chip. XXX */ | 
|  | return 1; | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int esp_check_spur_intr(struct esp *esp) | 
|  | { | 
|  | switch (esp->rev) { | 
|  | case ESP100: | 
|  | case ESP100A: | 
|  | /* The interrupt pending bit of the status register cannot | 
|  | * be trusted on these revisions. | 
|  | */ | 
|  | esp->sreg &= ~ESP_STAT_INTR; | 
|  | break; | 
|  |  | 
|  | default: | 
|  | if (!(esp->sreg & ESP_STAT_INTR)) { | 
|  | esp->ireg = esp_read8(ESP_INTRPT); | 
|  | if (esp->ireg & ESP_INTR_SR) | 
|  | return 1; | 
|  |  | 
|  | /* If the DMA is indicating interrupt pending and the | 
|  | * ESP is not, the only possibility is a DMA error. | 
|  | */ | 
|  | if (!esp->ops->dma_error(esp)) { | 
|  | printk(KERN_ERR PFX "esp%d: Spurious irq, " | 
|  | "sreg=%02x.\n", | 
|  | esp->host->unique_id, esp->sreg); | 
|  | return -1; | 
|  | } | 
|  |  | 
|  | printk(KERN_ERR PFX "esp%d: DMA error\n", | 
|  | esp->host->unique_id); | 
|  |  | 
|  | /* XXX Reset the chip. XXX */ | 
|  | return -1; | 
|  | } | 
|  | break; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void esp_schedule_reset(struct esp *esp) | 
|  | { | 
|  | esp_log_reset("ESP: esp_schedule_reset() from %p\n", | 
|  | __builtin_return_address(0)); | 
|  | esp->flags |= ESP_FLAG_RESETTING; | 
|  | esp_event(esp, ESP_EVENT_RESET); | 
|  | } | 
|  |  | 
|  | /* In order to avoid having to add a special half-reconnected state | 
|  | * into the driver we just sit here and poll through the rest of | 
|  | * the reselection process to get the tag message bytes. | 
|  | */ | 
|  | static struct esp_cmd_entry *esp_reconnect_with_tag(struct esp *esp, | 
|  | struct esp_lun_data *lp) | 
|  | { | 
|  | struct esp_cmd_entry *ent; | 
|  | int i; | 
|  |  | 
|  | if (!lp->num_tagged) { | 
|  | printk(KERN_ERR PFX "esp%d: Reconnect w/num_tagged==0\n", | 
|  | esp->host->unique_id); | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | esp_log_reconnect("ESP: reconnect tag, "); | 
|  |  | 
|  | for (i = 0; i < ESP_QUICKIRQ_LIMIT; i++) { | 
|  | if (esp->ops->irq_pending(esp)) | 
|  | break; | 
|  | } | 
|  | if (i == ESP_QUICKIRQ_LIMIT) { | 
|  | printk(KERN_ERR PFX "esp%d: Reconnect IRQ1 timeout\n", | 
|  | esp->host->unique_id); | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | esp->sreg = esp_read8(ESP_STATUS); | 
|  | esp->ireg = esp_read8(ESP_INTRPT); | 
|  |  | 
|  | esp_log_reconnect("IRQ(%d:%x:%x), ", | 
|  | i, esp->ireg, esp->sreg); | 
|  |  | 
|  | if (esp->ireg & ESP_INTR_DC) { | 
|  | printk(KERN_ERR PFX "esp%d: Reconnect, got disconnect.\n", | 
|  | esp->host->unique_id); | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | if ((esp->sreg & ESP_STAT_PMASK) != ESP_MIP) { | 
|  | printk(KERN_ERR PFX "esp%d: Reconnect, not MIP sreg[%02x].\n", | 
|  | esp->host->unique_id, esp->sreg); | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | /* DMA in the tag bytes... */ | 
|  | esp->command_block[0] = 0xff; | 
|  | esp->command_block[1] = 0xff; | 
|  | esp->ops->send_dma_cmd(esp, esp->command_block_dma, | 
|  | 2, 2, 1, ESP_CMD_DMA | ESP_CMD_TI); | 
|  |  | 
|  | /* ACK the msssage.  */ | 
|  | scsi_esp_cmd(esp, ESP_CMD_MOK); | 
|  |  | 
|  | for (i = 0; i < ESP_RESELECT_TAG_LIMIT; i++) { | 
|  | if (esp->ops->irq_pending(esp)) { | 
|  | esp->sreg = esp_read8(ESP_STATUS); | 
|  | esp->ireg = esp_read8(ESP_INTRPT); | 
|  | if (esp->ireg & ESP_INTR_FDONE) | 
|  | break; | 
|  | } | 
|  | udelay(1); | 
|  | } | 
|  | if (i == ESP_RESELECT_TAG_LIMIT) { | 
|  | printk(KERN_ERR PFX "esp%d: Reconnect IRQ2 timeout\n", | 
|  | esp->host->unique_id); | 
|  | return NULL; | 
|  | } | 
|  | esp->ops->dma_drain(esp); | 
|  | esp->ops->dma_invalidate(esp); | 
|  |  | 
|  | esp_log_reconnect("IRQ2(%d:%x:%x) tag[%x:%x]\n", | 
|  | i, esp->ireg, esp->sreg, | 
|  | esp->command_block[0], | 
|  | esp->command_block[1]); | 
|  |  | 
|  | if (esp->command_block[0] < SIMPLE_QUEUE_TAG || | 
|  | esp->command_block[0] > ORDERED_QUEUE_TAG) { | 
|  | printk(KERN_ERR PFX "esp%d: Reconnect, bad tag " | 
|  | "type %02x.\n", | 
|  | esp->host->unique_id, esp->command_block[0]); | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | ent = lp->tagged_cmds[esp->command_block[1]]; | 
|  | if (!ent) { | 
|  | printk(KERN_ERR PFX "esp%d: Reconnect, no entry for " | 
|  | "tag %02x.\n", | 
|  | esp->host->unique_id, esp->command_block[1]); | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | return ent; | 
|  | } | 
|  |  | 
|  | static int esp_reconnect(struct esp *esp) | 
|  | { | 
|  | struct esp_cmd_entry *ent; | 
|  | struct esp_target_data *tp; | 
|  | struct esp_lun_data *lp; | 
|  | struct scsi_device *dev; | 
|  | int target, lun; | 
|  |  | 
|  | BUG_ON(esp->active_cmd); | 
|  | if (esp->rev == FASHME) { | 
|  | /* FASHME puts the target and lun numbers directly | 
|  | * into the fifo. | 
|  | */ | 
|  | target = esp->fifo[0]; | 
|  | lun = esp->fifo[1] & 0x7; | 
|  | } else { | 
|  | u8 bits = esp_read8(ESP_FDATA); | 
|  |  | 
|  | /* Older chips put the lun directly into the fifo, but | 
|  | * the target is given as a sample of the arbitration | 
|  | * lines on the bus at reselection time.  So we should | 
|  | * see the ID of the ESP and the one reconnecting target | 
|  | * set in the bitmap. | 
|  | */ | 
|  | if (!(bits & esp->scsi_id_mask)) | 
|  | goto do_reset; | 
|  | bits &= ~esp->scsi_id_mask; | 
|  | if (!bits || (bits & (bits - 1))) | 
|  | goto do_reset; | 
|  |  | 
|  | target = ffs(bits) - 1; | 
|  | lun = (esp_read8(ESP_FDATA) & 0x7); | 
|  |  | 
|  | scsi_esp_cmd(esp, ESP_CMD_FLUSH); | 
|  | if (esp->rev == ESP100) { | 
|  | u8 ireg = esp_read8(ESP_INTRPT); | 
|  | /* This chip has a bug during reselection that can | 
|  | * cause a spurious illegal-command interrupt, which | 
|  | * we simply ACK here.  Another possibility is a bus | 
|  | * reset so we must check for that. | 
|  | */ | 
|  | if (ireg & ESP_INTR_SR) | 
|  | goto do_reset; | 
|  | } | 
|  | scsi_esp_cmd(esp, ESP_CMD_NULL); | 
|  | } | 
|  |  | 
|  | esp_write_tgt_sync(esp, target); | 
|  | esp_write_tgt_config3(esp, target); | 
|  |  | 
|  | scsi_esp_cmd(esp, ESP_CMD_MOK); | 
|  |  | 
|  | if (esp->rev == FASHME) | 
|  | esp_write8(target | ESP_BUSID_RESELID | ESP_BUSID_CTR32BIT, | 
|  | ESP_BUSID); | 
|  |  | 
|  | tp = &esp->target[target]; | 
|  | dev = __scsi_device_lookup_by_target(tp->starget, lun); | 
|  | if (!dev) { | 
|  | printk(KERN_ERR PFX "esp%d: Reconnect, no lp " | 
|  | "tgt[%u] lun[%u]\n", | 
|  | esp->host->unique_id, target, lun); | 
|  | goto do_reset; | 
|  | } | 
|  | lp = dev->hostdata; | 
|  |  | 
|  | ent = lp->non_tagged_cmd; | 
|  | if (!ent) { | 
|  | ent = esp_reconnect_with_tag(esp, lp); | 
|  | if (!ent) | 
|  | goto do_reset; | 
|  | } | 
|  |  | 
|  | esp->active_cmd = ent; | 
|  |  | 
|  | if (ent->flags & ESP_CMD_FLAG_ABORT) { | 
|  | esp->msg_out[0] = ABORT_TASK_SET; | 
|  | esp->msg_out_len = 1; | 
|  | scsi_esp_cmd(esp, ESP_CMD_SATN); | 
|  | } | 
|  |  | 
|  | esp_event(esp, ESP_EVENT_CHECK_PHASE); | 
|  | esp_restore_pointers(esp, ent); | 
|  | esp->flags |= ESP_FLAG_QUICKIRQ_CHECK; | 
|  | return 1; | 
|  |  | 
|  | do_reset: | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int esp_finish_select(struct esp *esp) | 
|  | { | 
|  | struct esp_cmd_entry *ent; | 
|  | struct scsi_cmnd *cmd; | 
|  | u8 orig_select_state; | 
|  |  | 
|  | orig_select_state = esp->select_state; | 
|  |  | 
|  | /* No longer selecting.  */ | 
|  | esp->select_state = ESP_SELECT_NONE; | 
|  |  | 
|  | esp->seqreg = esp_read8(ESP_SSTEP) & ESP_STEP_VBITS; | 
|  | ent = esp->active_cmd; | 
|  | cmd = ent->cmd; | 
|  |  | 
|  | if (esp->ops->dma_error(esp)) { | 
|  | /* If we see a DMA error during or as a result of selection, | 
|  | * all bets are off. | 
|  | */ | 
|  | esp_schedule_reset(esp); | 
|  | esp_cmd_is_done(esp, ent, cmd, (DID_ERROR << 16)); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | esp->ops->dma_invalidate(esp); | 
|  |  | 
|  | if (esp->ireg == (ESP_INTR_RSEL | ESP_INTR_FDONE)) { | 
|  | struct esp_target_data *tp = &esp->target[cmd->device->id]; | 
|  |  | 
|  | /* Carefully back out of the selection attempt.  Release | 
|  | * resources (such as DMA mapping & TAG) and reset state (such | 
|  | * as message out and command delivery variables). | 
|  | */ | 
|  | if (!(ent->flags & ESP_CMD_FLAG_AUTOSENSE)) { | 
|  | esp_unmap_dma(esp, cmd); | 
|  | esp_free_lun_tag(ent, cmd->device->hostdata); | 
|  | tp->flags &= ~(ESP_TGT_NEGO_SYNC | ESP_TGT_NEGO_WIDE); | 
|  | esp->flags &= ~ESP_FLAG_DOING_SLOWCMD; | 
|  | esp->cmd_bytes_ptr = NULL; | 
|  | esp->cmd_bytes_left = 0; | 
|  | } else { | 
|  | esp->ops->unmap_single(esp, ent->sense_dma, | 
|  | SCSI_SENSE_BUFFERSIZE, | 
|  | DMA_FROM_DEVICE); | 
|  | ent->sense_ptr = NULL; | 
|  | } | 
|  |  | 
|  | /* Now that the state is unwound properly, put back onto | 
|  | * the issue queue.  This command is no longer active. | 
|  | */ | 
|  | list_del(&ent->list); | 
|  | list_add(&ent->list, &esp->queued_cmds); | 
|  | esp->active_cmd = NULL; | 
|  |  | 
|  | /* Return value ignored by caller, it directly invokes | 
|  | * esp_reconnect(). | 
|  | */ | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | if (esp->ireg == ESP_INTR_DC) { | 
|  | struct scsi_device *dev = cmd->device; | 
|  |  | 
|  | /* Disconnect.  Make sure we re-negotiate sync and | 
|  | * wide parameters if this target starts responding | 
|  | * again in the future. | 
|  | */ | 
|  | esp->target[dev->id].flags |= ESP_TGT_CHECK_NEGO; | 
|  |  | 
|  | scsi_esp_cmd(esp, ESP_CMD_ESEL); | 
|  | esp_cmd_is_done(esp, ent, cmd, (DID_BAD_TARGET << 16)); | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | if (esp->ireg == (ESP_INTR_FDONE | ESP_INTR_BSERV)) { | 
|  | /* Selection successful.  On pre-FAST chips we have | 
|  | * to do a NOP and possibly clean out the FIFO. | 
|  | */ | 
|  | if (esp->rev <= ESP236) { | 
|  | int fcnt = esp_read8(ESP_FFLAGS) & ESP_FF_FBYTES; | 
|  |  | 
|  | scsi_esp_cmd(esp, ESP_CMD_NULL); | 
|  |  | 
|  | if (!fcnt && | 
|  | (!esp->prev_soff || | 
|  | ((esp->sreg & ESP_STAT_PMASK) != ESP_DIP))) | 
|  | esp_flush_fifo(esp); | 
|  | } | 
|  |  | 
|  | /* If we are doing a slow command, negotiation, etc. | 
|  | * we'll do the right thing as we transition to the | 
|  | * next phase. | 
|  | */ | 
|  | esp_event(esp, ESP_EVENT_CHECK_PHASE); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | printk("ESP: Unexpected selection completion ireg[%x].\n", | 
|  | esp->ireg); | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int esp_data_bytes_sent(struct esp *esp, struct esp_cmd_entry *ent, | 
|  | struct scsi_cmnd *cmd) | 
|  | { | 
|  | int fifo_cnt, ecount, bytes_sent, flush_fifo; | 
|  |  | 
|  | fifo_cnt = esp_read8(ESP_FFLAGS) & ESP_FF_FBYTES; | 
|  | if (esp->prev_cfg3 & ESP_CONFIG3_EWIDE) | 
|  | fifo_cnt <<= 1; | 
|  |  | 
|  | ecount = 0; | 
|  | if (!(esp->sreg & ESP_STAT_TCNT)) { | 
|  | ecount = ((unsigned int)esp_read8(ESP_TCLOW) | | 
|  | (((unsigned int)esp_read8(ESP_TCMED)) << 8)); | 
|  | if (esp->rev == FASHME) | 
|  | ecount |= ((unsigned int)esp_read8(FAS_RLO)) << 16; | 
|  | } | 
|  |  | 
|  | bytes_sent = esp->data_dma_len; | 
|  | bytes_sent -= ecount; | 
|  |  | 
|  | if (!(ent->flags & ESP_CMD_FLAG_WRITE)) | 
|  | bytes_sent -= fifo_cnt; | 
|  |  | 
|  | flush_fifo = 0; | 
|  | if (!esp->prev_soff) { | 
|  | /* Synchronous data transfer, always flush fifo. */ | 
|  | flush_fifo = 1; | 
|  | } else { | 
|  | if (esp->rev == ESP100) { | 
|  | u32 fflags, phase; | 
|  |  | 
|  | /* ESP100 has a chip bug where in the synchronous data | 
|  | * phase it can mistake a final long REQ pulse from the | 
|  | * target as an extra data byte.  Fun. | 
|  | * | 
|  | * To detect this case we resample the status register | 
|  | * and fifo flags.  If we're still in a data phase and | 
|  | * we see spurious chunks in the fifo, we return error | 
|  | * to the caller which should reset and set things up | 
|  | * such that we only try future transfers to this | 
|  | * target in synchronous mode. | 
|  | */ | 
|  | esp->sreg = esp_read8(ESP_STATUS); | 
|  | phase = esp->sreg & ESP_STAT_PMASK; | 
|  | fflags = esp_read8(ESP_FFLAGS); | 
|  |  | 
|  | if ((phase == ESP_DOP && | 
|  | (fflags & ESP_FF_ONOTZERO)) || | 
|  | (phase == ESP_DIP && | 
|  | (fflags & ESP_FF_FBYTES))) | 
|  | return -1; | 
|  | } | 
|  | if (!(ent->flags & ESP_CMD_FLAG_WRITE)) | 
|  | flush_fifo = 1; | 
|  | } | 
|  |  | 
|  | if (flush_fifo) | 
|  | esp_flush_fifo(esp); | 
|  |  | 
|  | return bytes_sent; | 
|  | } | 
|  |  | 
|  | static void esp_setsync(struct esp *esp, struct esp_target_data *tp, | 
|  | u8 scsi_period, u8 scsi_offset, | 
|  | u8 esp_stp, u8 esp_soff) | 
|  | { | 
|  | spi_period(tp->starget) = scsi_period; | 
|  | spi_offset(tp->starget) = scsi_offset; | 
|  | spi_width(tp->starget) = (tp->flags & ESP_TGT_WIDE) ? 1 : 0; | 
|  |  | 
|  | if (esp_soff) { | 
|  | esp_stp &= 0x1f; | 
|  | esp_soff |= esp->radelay; | 
|  | if (esp->rev >= FAS236) { | 
|  | u8 bit = ESP_CONFIG3_FSCSI; | 
|  | if (esp->rev >= FAS100A) | 
|  | bit = ESP_CONFIG3_FAST; | 
|  |  | 
|  | if (scsi_period < 50) { | 
|  | if (esp->rev == FASHME) | 
|  | esp_soff &= ~esp->radelay; | 
|  | tp->esp_config3 |= bit; | 
|  | } else { | 
|  | tp->esp_config3 &= ~bit; | 
|  | } | 
|  | esp->prev_cfg3 = tp->esp_config3; | 
|  | esp_write8(esp->prev_cfg3, ESP_CFG3); | 
|  | } | 
|  | } | 
|  |  | 
|  | tp->esp_period = esp->prev_stp = esp_stp; | 
|  | tp->esp_offset = esp->prev_soff = esp_soff; | 
|  |  | 
|  | esp_write8(esp_soff, ESP_SOFF); | 
|  | esp_write8(esp_stp, ESP_STP); | 
|  |  | 
|  | tp->flags &= ~(ESP_TGT_NEGO_SYNC | ESP_TGT_CHECK_NEGO); | 
|  |  | 
|  | spi_display_xfer_agreement(tp->starget); | 
|  | } | 
|  |  | 
|  | static void esp_msgin_reject(struct esp *esp) | 
|  | { | 
|  | struct esp_cmd_entry *ent = esp->active_cmd; | 
|  | struct scsi_cmnd *cmd = ent->cmd; | 
|  | struct esp_target_data *tp; | 
|  | int tgt; | 
|  |  | 
|  | tgt = cmd->device->id; | 
|  | tp = &esp->target[tgt]; | 
|  |  | 
|  | if (tp->flags & ESP_TGT_NEGO_WIDE) { | 
|  | tp->flags &= ~(ESP_TGT_NEGO_WIDE | ESP_TGT_WIDE); | 
|  |  | 
|  | if (!esp_need_to_nego_sync(tp)) { | 
|  | tp->flags &= ~ESP_TGT_CHECK_NEGO; | 
|  | scsi_esp_cmd(esp, ESP_CMD_RATN); | 
|  | } else { | 
|  | esp->msg_out_len = | 
|  | spi_populate_sync_msg(&esp->msg_out[0], | 
|  | tp->nego_goal_period, | 
|  | tp->nego_goal_offset); | 
|  | tp->flags |= ESP_TGT_NEGO_SYNC; | 
|  | scsi_esp_cmd(esp, ESP_CMD_SATN); | 
|  | } | 
|  | return; | 
|  | } | 
|  |  | 
|  | if (tp->flags & ESP_TGT_NEGO_SYNC) { | 
|  | tp->flags &= ~(ESP_TGT_NEGO_SYNC | ESP_TGT_CHECK_NEGO); | 
|  | tp->esp_period = 0; | 
|  | tp->esp_offset = 0; | 
|  | esp_setsync(esp, tp, 0, 0, 0, 0); | 
|  | scsi_esp_cmd(esp, ESP_CMD_RATN); | 
|  | return; | 
|  | } | 
|  |  | 
|  | esp->msg_out[0] = ABORT_TASK_SET; | 
|  | esp->msg_out_len = 1; | 
|  | scsi_esp_cmd(esp, ESP_CMD_SATN); | 
|  | } | 
|  |  | 
|  | static void esp_msgin_sdtr(struct esp *esp, struct esp_target_data *tp) | 
|  | { | 
|  | u8 period = esp->msg_in[3]; | 
|  | u8 offset = esp->msg_in[4]; | 
|  | u8 stp; | 
|  |  | 
|  | if (!(tp->flags & ESP_TGT_NEGO_SYNC)) | 
|  | goto do_reject; | 
|  |  | 
|  | if (offset > 15) | 
|  | goto do_reject; | 
|  |  | 
|  | if (offset) { | 
|  | int one_clock; | 
|  |  | 
|  | if (period > esp->max_period) { | 
|  | period = offset = 0; | 
|  | goto do_sdtr; | 
|  | } | 
|  | if (period < esp->min_period) | 
|  | goto do_reject; | 
|  |  | 
|  | one_clock = esp->ccycle / 1000; | 
|  | stp = DIV_ROUND_UP(period << 2, one_clock); | 
|  | if (stp && esp->rev >= FAS236) { | 
|  | if (stp >= 50) | 
|  | stp--; | 
|  | } | 
|  | } else { | 
|  | stp = 0; | 
|  | } | 
|  |  | 
|  | esp_setsync(esp, tp, period, offset, stp, offset); | 
|  | return; | 
|  |  | 
|  | do_reject: | 
|  | esp->msg_out[0] = MESSAGE_REJECT; | 
|  | esp->msg_out_len = 1; | 
|  | scsi_esp_cmd(esp, ESP_CMD_SATN); | 
|  | return; | 
|  |  | 
|  | do_sdtr: | 
|  | tp->nego_goal_period = period; | 
|  | tp->nego_goal_offset = offset; | 
|  | esp->msg_out_len = | 
|  | spi_populate_sync_msg(&esp->msg_out[0], | 
|  | tp->nego_goal_period, | 
|  | tp->nego_goal_offset); | 
|  | scsi_esp_cmd(esp, ESP_CMD_SATN); | 
|  | } | 
|  |  | 
|  | static void esp_msgin_wdtr(struct esp *esp, struct esp_target_data *tp) | 
|  | { | 
|  | int size = 8 << esp->msg_in[3]; | 
|  | u8 cfg3; | 
|  |  | 
|  | if (esp->rev != FASHME) | 
|  | goto do_reject; | 
|  |  | 
|  | if (size != 8 && size != 16) | 
|  | goto do_reject; | 
|  |  | 
|  | if (!(tp->flags & ESP_TGT_NEGO_WIDE)) | 
|  | goto do_reject; | 
|  |  | 
|  | cfg3 = tp->esp_config3; | 
|  | if (size == 16) { | 
|  | tp->flags |= ESP_TGT_WIDE; | 
|  | cfg3 |= ESP_CONFIG3_EWIDE; | 
|  | } else { | 
|  | tp->flags &= ~ESP_TGT_WIDE; | 
|  | cfg3 &= ~ESP_CONFIG3_EWIDE; | 
|  | } | 
|  | tp->esp_config3 = cfg3; | 
|  | esp->prev_cfg3 = cfg3; | 
|  | esp_write8(cfg3, ESP_CFG3); | 
|  |  | 
|  | tp->flags &= ~ESP_TGT_NEGO_WIDE; | 
|  |  | 
|  | spi_period(tp->starget) = 0; | 
|  | spi_offset(tp->starget) = 0; | 
|  | if (!esp_need_to_nego_sync(tp)) { | 
|  | tp->flags &= ~ESP_TGT_CHECK_NEGO; | 
|  | scsi_esp_cmd(esp, ESP_CMD_RATN); | 
|  | } else { | 
|  | esp->msg_out_len = | 
|  | spi_populate_sync_msg(&esp->msg_out[0], | 
|  | tp->nego_goal_period, | 
|  | tp->nego_goal_offset); | 
|  | tp->flags |= ESP_TGT_NEGO_SYNC; | 
|  | scsi_esp_cmd(esp, ESP_CMD_SATN); | 
|  | } | 
|  | return; | 
|  |  | 
|  | do_reject: | 
|  | esp->msg_out[0] = MESSAGE_REJECT; | 
|  | esp->msg_out_len = 1; | 
|  | scsi_esp_cmd(esp, ESP_CMD_SATN); | 
|  | } | 
|  |  | 
|  | static void esp_msgin_extended(struct esp *esp) | 
|  | { | 
|  | struct esp_cmd_entry *ent = esp->active_cmd; | 
|  | struct scsi_cmnd *cmd = ent->cmd; | 
|  | struct esp_target_data *tp; | 
|  | int tgt = cmd->device->id; | 
|  |  | 
|  | tp = &esp->target[tgt]; | 
|  | if (esp->msg_in[2] == EXTENDED_SDTR) { | 
|  | esp_msgin_sdtr(esp, tp); | 
|  | return; | 
|  | } | 
|  | if (esp->msg_in[2] == EXTENDED_WDTR) { | 
|  | esp_msgin_wdtr(esp, tp); | 
|  | return; | 
|  | } | 
|  |  | 
|  | printk("ESP: Unexpected extended msg type %x\n", | 
|  | esp->msg_in[2]); | 
|  |  | 
|  | esp->msg_out[0] = ABORT_TASK_SET; | 
|  | esp->msg_out_len = 1; | 
|  | scsi_esp_cmd(esp, ESP_CMD_SATN); | 
|  | } | 
|  |  | 
|  | /* Analyze msgin bytes received from target so far.  Return non-zero | 
|  | * if there are more bytes needed to complete the message. | 
|  | */ | 
|  | static int esp_msgin_process(struct esp *esp) | 
|  | { | 
|  | u8 msg0 = esp->msg_in[0]; | 
|  | int len = esp->msg_in_len; | 
|  |  | 
|  | if (msg0 & 0x80) { | 
|  | /* Identify */ | 
|  | printk("ESP: Unexpected msgin identify\n"); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | switch (msg0) { | 
|  | case EXTENDED_MESSAGE: | 
|  | if (len == 1) | 
|  | return 1; | 
|  | if (len < esp->msg_in[1] + 2) | 
|  | return 1; | 
|  | esp_msgin_extended(esp); | 
|  | return 0; | 
|  |  | 
|  | case IGNORE_WIDE_RESIDUE: { | 
|  | struct esp_cmd_entry *ent; | 
|  | struct esp_cmd_priv *spriv; | 
|  | if (len == 1) | 
|  | return 1; | 
|  |  | 
|  | if (esp->msg_in[1] != 1) | 
|  | goto do_reject; | 
|  |  | 
|  | ent = esp->active_cmd; | 
|  | spriv = ESP_CMD_PRIV(ent->cmd); | 
|  |  | 
|  | if (spriv->cur_residue == sg_dma_len(spriv->cur_sg)) { | 
|  | spriv->cur_sg--; | 
|  | spriv->cur_residue = 1; | 
|  | } else | 
|  | spriv->cur_residue++; | 
|  | spriv->tot_residue++; | 
|  | return 0; | 
|  | } | 
|  | case NOP: | 
|  | return 0; | 
|  | case RESTORE_POINTERS: | 
|  | esp_restore_pointers(esp, esp->active_cmd); | 
|  | return 0; | 
|  | case SAVE_POINTERS: | 
|  | esp_save_pointers(esp, esp->active_cmd); | 
|  | return 0; | 
|  |  | 
|  | case COMMAND_COMPLETE: | 
|  | case DISCONNECT: { | 
|  | struct esp_cmd_entry *ent = esp->active_cmd; | 
|  |  | 
|  | ent->message = msg0; | 
|  | esp_event(esp, ESP_EVENT_FREE_BUS); | 
|  | esp->flags |= ESP_FLAG_QUICKIRQ_CHECK; | 
|  | return 0; | 
|  | } | 
|  | case MESSAGE_REJECT: | 
|  | esp_msgin_reject(esp); | 
|  | return 0; | 
|  |  | 
|  | default: | 
|  | do_reject: | 
|  | esp->msg_out[0] = MESSAGE_REJECT; | 
|  | esp->msg_out_len = 1; | 
|  | scsi_esp_cmd(esp, ESP_CMD_SATN); | 
|  | return 0; | 
|  | } | 
|  | } | 
|  |  | 
|  | static int esp_process_event(struct esp *esp) | 
|  | { | 
|  | int write; | 
|  |  | 
|  | again: | 
|  | write = 0; | 
|  | switch (esp->event) { | 
|  | case ESP_EVENT_CHECK_PHASE: | 
|  | switch (esp->sreg & ESP_STAT_PMASK) { | 
|  | case ESP_DOP: | 
|  | esp_event(esp, ESP_EVENT_DATA_OUT); | 
|  | break; | 
|  | case ESP_DIP: | 
|  | esp_event(esp, ESP_EVENT_DATA_IN); | 
|  | break; | 
|  | case ESP_STATP: | 
|  | esp_flush_fifo(esp); | 
|  | scsi_esp_cmd(esp, ESP_CMD_ICCSEQ); | 
|  | esp_event(esp, ESP_EVENT_STATUS); | 
|  | esp->flags |= ESP_FLAG_QUICKIRQ_CHECK; | 
|  | return 1; | 
|  |  | 
|  | case ESP_MOP: | 
|  | esp_event(esp, ESP_EVENT_MSGOUT); | 
|  | break; | 
|  |  | 
|  | case ESP_MIP: | 
|  | esp_event(esp, ESP_EVENT_MSGIN); | 
|  | break; | 
|  |  | 
|  | case ESP_CMDP: | 
|  | esp_event(esp, ESP_EVENT_CMD_START); | 
|  | break; | 
|  |  | 
|  | default: | 
|  | printk("ESP: Unexpected phase, sreg=%02x\n", | 
|  | esp->sreg); | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | } | 
|  | goto again; | 
|  | break; | 
|  |  | 
|  | case ESP_EVENT_DATA_IN: | 
|  | write = 1; | 
|  | /* fallthru */ | 
|  |  | 
|  | case ESP_EVENT_DATA_OUT: { | 
|  | struct esp_cmd_entry *ent = esp->active_cmd; | 
|  | struct scsi_cmnd *cmd = ent->cmd; | 
|  | dma_addr_t dma_addr = esp_cur_dma_addr(ent, cmd); | 
|  | unsigned int dma_len = esp_cur_dma_len(ent, cmd); | 
|  |  | 
|  | if (esp->rev == ESP100) | 
|  | scsi_esp_cmd(esp, ESP_CMD_NULL); | 
|  |  | 
|  | if (write) | 
|  | ent->flags |= ESP_CMD_FLAG_WRITE; | 
|  | else | 
|  | ent->flags &= ~ESP_CMD_FLAG_WRITE; | 
|  |  | 
|  | if (esp->ops->dma_length_limit) | 
|  | dma_len = esp->ops->dma_length_limit(esp, dma_addr, | 
|  | dma_len); | 
|  | else | 
|  | dma_len = esp_dma_length_limit(esp, dma_addr, dma_len); | 
|  |  | 
|  | esp->data_dma_len = dma_len; | 
|  |  | 
|  | if (!dma_len) { | 
|  | printk(KERN_ERR PFX "esp%d: DMA length is zero!\n", | 
|  | esp->host->unique_id); | 
|  | printk(KERN_ERR PFX "esp%d: cur adr[%08llx] len[%08x]\n", | 
|  | esp->host->unique_id, | 
|  | (unsigned long long)esp_cur_dma_addr(ent, cmd), | 
|  | esp_cur_dma_len(ent, cmd)); | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | esp_log_datastart("ESP: start data addr[%08llx] len[%u] " | 
|  | "write(%d)\n", | 
|  | (unsigned long long)dma_addr, dma_len, write); | 
|  |  | 
|  | esp->ops->send_dma_cmd(esp, dma_addr, dma_len, dma_len, | 
|  | write, ESP_CMD_DMA | ESP_CMD_TI); | 
|  | esp_event(esp, ESP_EVENT_DATA_DONE); | 
|  | break; | 
|  | } | 
|  | case ESP_EVENT_DATA_DONE: { | 
|  | struct esp_cmd_entry *ent = esp->active_cmd; | 
|  | struct scsi_cmnd *cmd = ent->cmd; | 
|  | int bytes_sent; | 
|  |  | 
|  | if (esp->ops->dma_error(esp)) { | 
|  | printk("ESP: data done, DMA error, resetting\n"); | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | if (ent->flags & ESP_CMD_FLAG_WRITE) { | 
|  | /* XXX parity errors, etc. XXX */ | 
|  |  | 
|  | esp->ops->dma_drain(esp); | 
|  | } | 
|  | esp->ops->dma_invalidate(esp); | 
|  |  | 
|  | if (esp->ireg != ESP_INTR_BSERV) { | 
|  | /* We should always see exactly a bus-service | 
|  | * interrupt at the end of a successful transfer. | 
|  | */ | 
|  | printk("ESP: data done, not BSERV, resetting\n"); | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | bytes_sent = esp_data_bytes_sent(esp, ent, cmd); | 
|  |  | 
|  | esp_log_datadone("ESP: data done flgs[%x] sent[%d]\n", | 
|  | ent->flags, bytes_sent); | 
|  |  | 
|  | if (bytes_sent < 0) { | 
|  | /* XXX force sync mode for this target XXX */ | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | esp_advance_dma(esp, ent, cmd, bytes_sent); | 
|  | esp_event(esp, ESP_EVENT_CHECK_PHASE); | 
|  | goto again; | 
|  | } | 
|  |  | 
|  | case ESP_EVENT_STATUS: { | 
|  | struct esp_cmd_entry *ent = esp->active_cmd; | 
|  |  | 
|  | if (esp->ireg & ESP_INTR_FDONE) { | 
|  | ent->status = esp_read8(ESP_FDATA); | 
|  | ent->message = esp_read8(ESP_FDATA); | 
|  | scsi_esp_cmd(esp, ESP_CMD_MOK); | 
|  | } else if (esp->ireg == ESP_INTR_BSERV) { | 
|  | ent->status = esp_read8(ESP_FDATA); | 
|  | ent->message = 0xff; | 
|  | esp_event(esp, ESP_EVENT_MSGIN); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | if (ent->message != COMMAND_COMPLETE) { | 
|  | printk("ESP: Unexpected message %x in status\n", | 
|  | ent->message); | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | esp_event(esp, ESP_EVENT_FREE_BUS); | 
|  | esp->flags |= ESP_FLAG_QUICKIRQ_CHECK; | 
|  | break; | 
|  | } | 
|  | case ESP_EVENT_FREE_BUS: { | 
|  | struct esp_cmd_entry *ent = esp->active_cmd; | 
|  | struct scsi_cmnd *cmd = ent->cmd; | 
|  |  | 
|  | if (ent->message == COMMAND_COMPLETE || | 
|  | ent->message == DISCONNECT) | 
|  | scsi_esp_cmd(esp, ESP_CMD_ESEL); | 
|  |  | 
|  | if (ent->message == COMMAND_COMPLETE) { | 
|  | esp_log_cmddone("ESP: Command done status[%x] " | 
|  | "message[%x]\n", | 
|  | ent->status, ent->message); | 
|  | if (ent->status == SAM_STAT_TASK_SET_FULL) | 
|  | esp_event_queue_full(esp, ent); | 
|  |  | 
|  | if (ent->status == SAM_STAT_CHECK_CONDITION && | 
|  | !(ent->flags & ESP_CMD_FLAG_AUTOSENSE)) { | 
|  | ent->flags |= ESP_CMD_FLAG_AUTOSENSE; | 
|  | esp_autosense(esp, ent); | 
|  | } else { | 
|  | esp_cmd_is_done(esp, ent, cmd, | 
|  | compose_result(ent->status, | 
|  | ent->message, | 
|  | DID_OK)); | 
|  | } | 
|  | } else if (ent->message == DISCONNECT) { | 
|  | esp_log_disconnect("ESP: Disconnecting tgt[%d] " | 
|  | "tag[%x:%x]\n", | 
|  | cmd->device->id, | 
|  | ent->tag[0], ent->tag[1]); | 
|  |  | 
|  | esp->active_cmd = NULL; | 
|  | esp_maybe_execute_command(esp); | 
|  | } else { | 
|  | printk("ESP: Unexpected message %x in freebus\n", | 
|  | ent->message); | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | } | 
|  | if (esp->active_cmd) | 
|  | esp->flags |= ESP_FLAG_QUICKIRQ_CHECK; | 
|  | break; | 
|  | } | 
|  | case ESP_EVENT_MSGOUT: { | 
|  | scsi_esp_cmd(esp, ESP_CMD_FLUSH); | 
|  |  | 
|  | if (esp_debug & ESP_DEBUG_MSGOUT) { | 
|  | int i; | 
|  | printk("ESP: Sending message [ "); | 
|  | for (i = 0; i < esp->msg_out_len; i++) | 
|  | printk("%02x ", esp->msg_out[i]); | 
|  | printk("]\n"); | 
|  | } | 
|  |  | 
|  | if (esp->rev == FASHME) { | 
|  | int i; | 
|  |  | 
|  | /* Always use the fifo.  */ | 
|  | for (i = 0; i < esp->msg_out_len; i++) { | 
|  | esp_write8(esp->msg_out[i], ESP_FDATA); | 
|  | esp_write8(0, ESP_FDATA); | 
|  | } | 
|  | scsi_esp_cmd(esp, ESP_CMD_TI); | 
|  | } else { | 
|  | if (esp->msg_out_len == 1) { | 
|  | esp_write8(esp->msg_out[0], ESP_FDATA); | 
|  | scsi_esp_cmd(esp, ESP_CMD_TI); | 
|  | } else { | 
|  | /* Use DMA. */ | 
|  | memcpy(esp->command_block, | 
|  | esp->msg_out, | 
|  | esp->msg_out_len); | 
|  |  | 
|  | esp->ops->send_dma_cmd(esp, | 
|  | esp->command_block_dma, | 
|  | esp->msg_out_len, | 
|  | esp->msg_out_len, | 
|  | 0, | 
|  | ESP_CMD_DMA|ESP_CMD_TI); | 
|  | } | 
|  | } | 
|  | esp_event(esp, ESP_EVENT_MSGOUT_DONE); | 
|  | break; | 
|  | } | 
|  | case ESP_EVENT_MSGOUT_DONE: | 
|  | if (esp->rev == FASHME) { | 
|  | scsi_esp_cmd(esp, ESP_CMD_FLUSH); | 
|  | } else { | 
|  | if (esp->msg_out_len > 1) | 
|  | esp->ops->dma_invalidate(esp); | 
|  | } | 
|  |  | 
|  | if (!(esp->ireg & ESP_INTR_DC)) { | 
|  | if (esp->rev != FASHME) | 
|  | scsi_esp_cmd(esp, ESP_CMD_NULL); | 
|  | } | 
|  | esp_event(esp, ESP_EVENT_CHECK_PHASE); | 
|  | goto again; | 
|  | case ESP_EVENT_MSGIN: | 
|  | if (esp->ireg & ESP_INTR_BSERV) { | 
|  | if (esp->rev == FASHME) { | 
|  | if (!(esp_read8(ESP_STATUS2) & | 
|  | ESP_STAT2_FEMPTY)) | 
|  | scsi_esp_cmd(esp, ESP_CMD_FLUSH); | 
|  | } else { | 
|  | scsi_esp_cmd(esp, ESP_CMD_FLUSH); | 
|  | if (esp->rev == ESP100) | 
|  | scsi_esp_cmd(esp, ESP_CMD_NULL); | 
|  | } | 
|  | scsi_esp_cmd(esp, ESP_CMD_TI); | 
|  | esp->flags |= ESP_FLAG_QUICKIRQ_CHECK; | 
|  | return 1; | 
|  | } | 
|  | if (esp->ireg & ESP_INTR_FDONE) { | 
|  | u8 val; | 
|  |  | 
|  | if (esp->rev == FASHME) | 
|  | val = esp->fifo[0]; | 
|  | else | 
|  | val = esp_read8(ESP_FDATA); | 
|  | esp->msg_in[esp->msg_in_len++] = val; | 
|  |  | 
|  | esp_log_msgin("ESP: Got msgin byte %x\n", val); | 
|  |  | 
|  | if (!esp_msgin_process(esp)) | 
|  | esp->msg_in_len = 0; | 
|  |  | 
|  | if (esp->rev == FASHME) | 
|  | scsi_esp_cmd(esp, ESP_CMD_FLUSH); | 
|  |  | 
|  | scsi_esp_cmd(esp, ESP_CMD_MOK); | 
|  |  | 
|  | if (esp->event != ESP_EVENT_FREE_BUS) | 
|  | esp_event(esp, ESP_EVENT_CHECK_PHASE); | 
|  | } else { | 
|  | printk("ESP: MSGIN neither BSERV not FDON, resetting"); | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | } | 
|  | break; | 
|  | case ESP_EVENT_CMD_START: | 
|  | memcpy(esp->command_block, esp->cmd_bytes_ptr, | 
|  | esp->cmd_bytes_left); | 
|  | if (esp->rev == FASHME) | 
|  | scsi_esp_cmd(esp, ESP_CMD_FLUSH); | 
|  | esp->ops->send_dma_cmd(esp, esp->command_block_dma, | 
|  | esp->cmd_bytes_left, 16, 0, | 
|  | ESP_CMD_DMA | ESP_CMD_TI); | 
|  | esp_event(esp, ESP_EVENT_CMD_DONE); | 
|  | esp->flags |= ESP_FLAG_QUICKIRQ_CHECK; | 
|  | break; | 
|  | case ESP_EVENT_CMD_DONE: | 
|  | esp->ops->dma_invalidate(esp); | 
|  | if (esp->ireg & ESP_INTR_BSERV) { | 
|  | esp_event(esp, ESP_EVENT_CHECK_PHASE); | 
|  | goto again; | 
|  | } | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | break; | 
|  |  | 
|  | case ESP_EVENT_RESET: | 
|  | scsi_esp_cmd(esp, ESP_CMD_RS); | 
|  | break; | 
|  |  | 
|  | default: | 
|  | printk("ESP: Unexpected event %x, resetting\n", | 
|  | esp->event); | 
|  | esp_schedule_reset(esp); | 
|  | return 0; | 
|  | break; | 
|  | } | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static void esp_reset_cleanup_one(struct esp *esp, struct esp_cmd_entry *ent) | 
|  | { | 
|  | struct scsi_cmnd *cmd = ent->cmd; | 
|  |  | 
|  | esp_unmap_dma(esp, cmd); | 
|  | esp_free_lun_tag(ent, cmd->device->hostdata); | 
|  | cmd->result = DID_RESET << 16; | 
|  |  | 
|  | if (ent->flags & ESP_CMD_FLAG_AUTOSENSE) { | 
|  | esp->ops->unmap_single(esp, ent->sense_dma, | 
|  | SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); | 
|  | ent->sense_ptr = NULL; | 
|  | } | 
|  |  | 
|  | cmd->scsi_done(cmd); | 
|  | list_del(&ent->list); | 
|  | esp_put_ent(esp, ent); | 
|  | } | 
|  |  | 
|  | static void esp_clear_hold(struct scsi_device *dev, void *data) | 
|  | { | 
|  | struct esp_lun_data *lp = dev->hostdata; | 
|  |  | 
|  | BUG_ON(lp->num_tagged); | 
|  | lp->hold = 0; | 
|  | } | 
|  |  | 
|  | static void esp_reset_cleanup(struct esp *esp) | 
|  | { | 
|  | struct esp_cmd_entry *ent, *tmp; | 
|  | int i; | 
|  |  | 
|  | list_for_each_entry_safe(ent, tmp, &esp->queued_cmds, list) { | 
|  | struct scsi_cmnd *cmd = ent->cmd; | 
|  |  | 
|  | list_del(&ent->list); | 
|  | cmd->result = DID_RESET << 16; | 
|  | cmd->scsi_done(cmd); | 
|  | esp_put_ent(esp, ent); | 
|  | } | 
|  |  | 
|  | list_for_each_entry_safe(ent, tmp, &esp->active_cmds, list) { | 
|  | if (ent == esp->active_cmd) | 
|  | esp->active_cmd = NULL; | 
|  | esp_reset_cleanup_one(esp, ent); | 
|  | } | 
|  |  | 
|  | BUG_ON(esp->active_cmd != NULL); | 
|  |  | 
|  | /* Force renegotiation of sync/wide transfers.  */ | 
|  | for (i = 0; i < ESP_MAX_TARGET; i++) { | 
|  | struct esp_target_data *tp = &esp->target[i]; | 
|  |  | 
|  | tp->esp_period = 0; | 
|  | tp->esp_offset = 0; | 
|  | tp->esp_config3 &= ~(ESP_CONFIG3_EWIDE | | 
|  | ESP_CONFIG3_FSCSI | | 
|  | ESP_CONFIG3_FAST); | 
|  | tp->flags &= ~ESP_TGT_WIDE; | 
|  | tp->flags |= ESP_TGT_CHECK_NEGO; | 
|  |  | 
|  | if (tp->starget) | 
|  | __starget_for_each_device(tp->starget, NULL, | 
|  | esp_clear_hold); | 
|  | } | 
|  | esp->flags &= ~ESP_FLAG_RESETTING; | 
|  | } | 
|  |  | 
|  | /* Runs under host->lock */ | 
|  | static void __esp_interrupt(struct esp *esp) | 
|  | { | 
|  | int finish_reset, intr_done; | 
|  | u8 phase; | 
|  |  | 
|  | esp->sreg = esp_read8(ESP_STATUS); | 
|  |  | 
|  | if (esp->flags & ESP_FLAG_RESETTING) { | 
|  | finish_reset = 1; | 
|  | } else { | 
|  | if (esp_check_gross_error(esp)) | 
|  | return; | 
|  |  | 
|  | finish_reset = esp_check_spur_intr(esp); | 
|  | if (finish_reset < 0) | 
|  | return; | 
|  | } | 
|  |  | 
|  | esp->ireg = esp_read8(ESP_INTRPT); | 
|  |  | 
|  | if (esp->ireg & ESP_INTR_SR) | 
|  | finish_reset = 1; | 
|  |  | 
|  | if (finish_reset) { | 
|  | esp_reset_cleanup(esp); | 
|  | if (esp->eh_reset) { | 
|  | complete(esp->eh_reset); | 
|  | esp->eh_reset = NULL; | 
|  | } | 
|  | return; | 
|  | } | 
|  |  | 
|  | phase = (esp->sreg & ESP_STAT_PMASK); | 
|  | if (esp->rev == FASHME) { | 
|  | if (((phase != ESP_DIP && phase != ESP_DOP) && | 
|  | esp->select_state == ESP_SELECT_NONE && | 
|  | esp->event != ESP_EVENT_STATUS && | 
|  | esp->event != ESP_EVENT_DATA_DONE) || | 
|  | (esp->ireg & ESP_INTR_RSEL)) { | 
|  | esp->sreg2 = esp_read8(ESP_STATUS2); | 
|  | if (!(esp->sreg2 & ESP_STAT2_FEMPTY) || | 
|  | (esp->sreg2 & ESP_STAT2_F1BYTE)) | 
|  | hme_read_fifo(esp); | 
|  | } | 
|  | } | 
|  |  | 
|  | esp_log_intr("ESP: intr sreg[%02x] seqreg[%02x] " | 
|  | "sreg2[%02x] ireg[%02x]\n", | 
|  | esp->sreg, esp->seqreg, esp->sreg2, esp->ireg); | 
|  |  | 
|  | intr_done = 0; | 
|  |  | 
|  | if (esp->ireg & (ESP_INTR_S | ESP_INTR_SATN | ESP_INTR_IC)) { | 
|  | printk("ESP: unexpected IREG %02x\n", esp->ireg); | 
|  | if (esp->ireg & ESP_INTR_IC) | 
|  | esp_dump_cmd_log(esp); | 
|  |  | 
|  | esp_schedule_reset(esp); | 
|  | } else { | 
|  | if (!(esp->ireg & ESP_INTR_RSEL)) { | 
|  | /* Some combination of FDONE, BSERV, DC.  */ | 
|  | if (esp->select_state != ESP_SELECT_NONE) | 
|  | intr_done = esp_finish_select(esp); | 
|  | } else if (esp->ireg & ESP_INTR_RSEL) { | 
|  | if (esp->active_cmd) | 
|  | (void) esp_finish_select(esp); | 
|  | intr_done = esp_reconnect(esp); | 
|  | } | 
|  | } | 
|  | while (!intr_done) | 
|  | intr_done = esp_process_event(esp); | 
|  | } | 
|  |  | 
|  | irqreturn_t scsi_esp_intr(int irq, void *dev_id) | 
|  | { | 
|  | struct esp *esp = dev_id; | 
|  | unsigned long flags; | 
|  | irqreturn_t ret; | 
|  |  | 
|  | spin_lock_irqsave(esp->host->host_lock, flags); | 
|  | ret = IRQ_NONE; | 
|  | if (esp->ops->irq_pending(esp)) { | 
|  | ret = IRQ_HANDLED; | 
|  | for (;;) { | 
|  | int i; | 
|  |  | 
|  | __esp_interrupt(esp); | 
|  | if (!(esp->flags & ESP_FLAG_QUICKIRQ_CHECK)) | 
|  | break; | 
|  | esp->flags &= ~ESP_FLAG_QUICKIRQ_CHECK; | 
|  |  | 
|  | for (i = 0; i < ESP_QUICKIRQ_LIMIT; i++) { | 
|  | if (esp->ops->irq_pending(esp)) | 
|  | break; | 
|  | } | 
|  | if (i == ESP_QUICKIRQ_LIMIT) | 
|  | break; | 
|  | } | 
|  | } | 
|  | spin_unlock_irqrestore(esp->host->host_lock, flags); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  | EXPORT_SYMBOL(scsi_esp_intr); | 
|  |  | 
|  | static void esp_get_revision(struct esp *esp) | 
|  | { | 
|  | u8 val; | 
|  |  | 
|  | esp->config1 = (ESP_CONFIG1_PENABLE | (esp->scsi_id & 7)); | 
|  | esp->config2 = (ESP_CONFIG2_SCSI2ENAB | ESP_CONFIG2_REGPARITY); | 
|  | esp_write8(esp->config2, ESP_CFG2); | 
|  |  | 
|  | val = esp_read8(ESP_CFG2); | 
|  | val &= ~ESP_CONFIG2_MAGIC; | 
|  | if (val != (ESP_CONFIG2_SCSI2ENAB | ESP_CONFIG2_REGPARITY)) { | 
|  | /* If what we write to cfg2 does not come back, cfg2 is not | 
|  | * implemented, therefore this must be a plain esp100. | 
|  | */ | 
|  | esp->rev = ESP100; | 
|  | } else { | 
|  | esp->config2 = 0; | 
|  | esp_set_all_config3(esp, 5); | 
|  | esp->prev_cfg3 = 5; | 
|  | esp_write8(esp->config2, ESP_CFG2); | 
|  | esp_write8(0, ESP_CFG3); | 
|  | esp_write8(esp->prev_cfg3, ESP_CFG3); | 
|  |  | 
|  | val = esp_read8(ESP_CFG3); | 
|  | if (val != 5) { | 
|  | /* The cfg2 register is implemented, however | 
|  | * cfg3 is not, must be esp100a. | 
|  | */ | 
|  | esp->rev = ESP100A; | 
|  | } else { | 
|  | esp_set_all_config3(esp, 0); | 
|  | esp->prev_cfg3 = 0; | 
|  | esp_write8(esp->prev_cfg3, ESP_CFG3); | 
|  |  | 
|  | /* All of cfg{1,2,3} implemented, must be one of | 
|  | * the fas variants, figure out which one. | 
|  | */ | 
|  | if (esp->cfact == 0 || esp->cfact > ESP_CCF_F5) { | 
|  | esp->rev = FAST; | 
|  | esp->sync_defp = SYNC_DEFP_FAST; | 
|  | } else { | 
|  | esp->rev = ESP236; | 
|  | } | 
|  | esp->config2 = 0; | 
|  | esp_write8(esp->config2, ESP_CFG2); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static void esp_init_swstate(struct esp *esp) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | INIT_LIST_HEAD(&esp->queued_cmds); | 
|  | INIT_LIST_HEAD(&esp->active_cmds); | 
|  | INIT_LIST_HEAD(&esp->esp_cmd_pool); | 
|  |  | 
|  | /* Start with a clear state, domain validation (via ->slave_configure, | 
|  | * spi_dv_device()) will attempt to enable SYNC, WIDE, and tagged | 
|  | * commands. | 
|  | */ | 
|  | for (i = 0 ; i < ESP_MAX_TARGET; i++) { | 
|  | esp->target[i].flags = 0; | 
|  | esp->target[i].nego_goal_period = 0; | 
|  | esp->target[i].nego_goal_offset = 0; | 
|  | esp->target[i].nego_goal_width = 0; | 
|  | esp->target[i].nego_goal_tags = 0; | 
|  | } | 
|  | } | 
|  |  | 
|  | /* This places the ESP into a known state at boot time. */ | 
|  | static void esp_bootup_reset(struct esp *esp) | 
|  | { | 
|  | u8 val; | 
|  |  | 
|  | /* Reset the DMA */ | 
|  | esp->ops->reset_dma(esp); | 
|  |  | 
|  | /* Reset the ESP */ | 
|  | esp_reset_esp(esp); | 
|  |  | 
|  | /* Reset the SCSI bus, but tell ESP not to generate an irq */ | 
|  | val = esp_read8(ESP_CFG1); | 
|  | val |= ESP_CONFIG1_SRRDISAB; | 
|  | esp_write8(val, ESP_CFG1); | 
|  |  | 
|  | scsi_esp_cmd(esp, ESP_CMD_RS); | 
|  | udelay(400); | 
|  |  | 
|  | esp_write8(esp->config1, ESP_CFG1); | 
|  |  | 
|  | /* Eat any bitrot in the chip and we are done... */ | 
|  | esp_read8(ESP_INTRPT); | 
|  | } | 
|  |  | 
|  | static void esp_set_clock_params(struct esp *esp) | 
|  | { | 
|  | int fhz; | 
|  | u8 ccf; | 
|  |  | 
|  | /* This is getting messy but it has to be done correctly or else | 
|  | * you get weird behavior all over the place.  We are trying to | 
|  | * basically figure out three pieces of information. | 
|  | * | 
|  | * a) Clock Conversion Factor | 
|  | * | 
|  | *    This is a representation of the input crystal clock frequency | 
|  | *    going into the ESP on this machine.  Any operation whose timing | 
|  | *    is longer than 400ns depends on this value being correct.  For | 
|  | *    example, you'll get blips for arbitration/selection during high | 
|  | *    load or with multiple targets if this is not set correctly. | 
|  | * | 
|  | * b) Selection Time-Out | 
|  | * | 
|  | *    The ESP isn't very bright and will arbitrate for the bus and try | 
|  | *    to select a target forever if you let it.  This value tells the | 
|  | *    ESP when it has taken too long to negotiate and that it should | 
|  | *    interrupt the CPU so we can see what happened.  The value is | 
|  | *    computed as follows (from NCR/Symbios chip docs). | 
|  | * | 
|  | *          (Time Out Period) *  (Input Clock) | 
|  | *    STO = ---------------------------------- | 
|  | *          (8192) * (Clock Conversion Factor) | 
|  | * | 
|  | *    We use a time out period of 250ms (ESP_BUS_TIMEOUT). | 
|  | * | 
|  | * c) Imperical constants for synchronous offset and transfer period | 
|  | *    register values | 
|  | * | 
|  | *    This entails the smallest and largest sync period we could ever | 
|  | *    handle on this ESP. | 
|  | */ | 
|  | fhz = esp->cfreq; | 
|  |  | 
|  | ccf = ((fhz / 1000000) + 4) / 5; | 
|  | if (ccf == 1) | 
|  | ccf = 2; | 
|  |  | 
|  | /* If we can't find anything reasonable, just assume 20MHZ. | 
|  | * This is the clock frequency of the older sun4c's where I've | 
|  | * been unable to find the clock-frequency PROM property.  All | 
|  | * other machines provide useful values it seems. | 
|  | */ | 
|  | if (fhz <= 5000000 || ccf < 1 || ccf > 8) { | 
|  | fhz = 20000000; | 
|  | ccf = 4; | 
|  | } | 
|  |  | 
|  | esp->cfact = (ccf == 8 ? 0 : ccf); | 
|  | esp->cfreq = fhz; | 
|  | esp->ccycle = ESP_HZ_TO_CYCLE(fhz); | 
|  | esp->ctick = ESP_TICK(ccf, esp->ccycle); | 
|  | esp->neg_defp = ESP_NEG_DEFP(fhz, ccf); | 
|  | esp->sync_defp = SYNC_DEFP_SLOW; | 
|  | } | 
|  |  | 
|  | static const char *esp_chip_names[] = { | 
|  | "ESP100", | 
|  | "ESP100A", | 
|  | "ESP236", | 
|  | "FAS236", | 
|  | "FAS100A", | 
|  | "FAST", | 
|  | "FASHME", | 
|  | }; | 
|  |  | 
|  | static struct scsi_transport_template *esp_transport_template; | 
|  |  | 
|  | int scsi_esp_register(struct esp *esp, struct device *dev) | 
|  | { | 
|  | static int instance; | 
|  | int err; | 
|  |  | 
|  | esp->host->transportt = esp_transport_template; | 
|  | esp->host->max_lun = ESP_MAX_LUN; | 
|  | esp->host->cmd_per_lun = 2; | 
|  | esp->host->unique_id = instance; | 
|  |  | 
|  | esp_set_clock_params(esp); | 
|  |  | 
|  | esp_get_revision(esp); | 
|  |  | 
|  | esp_init_swstate(esp); | 
|  |  | 
|  | esp_bootup_reset(esp); | 
|  |  | 
|  | printk(KERN_INFO PFX "esp%u, regs[%1p:%1p] irq[%u]\n", | 
|  | esp->host->unique_id, esp->regs, esp->dma_regs, | 
|  | esp->host->irq); | 
|  | printk(KERN_INFO PFX "esp%u is a %s, %u MHz (ccf=%u), SCSI ID %u\n", | 
|  | esp->host->unique_id, esp_chip_names[esp->rev], | 
|  | esp->cfreq / 1000000, esp->cfact, esp->scsi_id); | 
|  |  | 
|  | /* Let the SCSI bus reset settle. */ | 
|  | ssleep(esp_bus_reset_settle); | 
|  |  | 
|  | err = scsi_add_host(esp->host, dev); | 
|  | if (err) | 
|  | return err; | 
|  |  | 
|  | instance++; | 
|  |  | 
|  | scsi_scan_host(esp->host); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  | EXPORT_SYMBOL(scsi_esp_register); | 
|  |  | 
|  | void scsi_esp_unregister(struct esp *esp) | 
|  | { | 
|  | scsi_remove_host(esp->host); | 
|  | } | 
|  | EXPORT_SYMBOL(scsi_esp_unregister); | 
|  |  | 
|  | static int esp_target_alloc(struct scsi_target *starget) | 
|  | { | 
|  | struct esp *esp = shost_priv(dev_to_shost(&starget->dev)); | 
|  | struct esp_target_data *tp = &esp->target[starget->id]; | 
|  |  | 
|  | tp->starget = starget; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void esp_target_destroy(struct scsi_target *starget) | 
|  | { | 
|  | struct esp *esp = shost_priv(dev_to_shost(&starget->dev)); | 
|  | struct esp_target_data *tp = &esp->target[starget->id]; | 
|  |  | 
|  | tp->starget = NULL; | 
|  | } | 
|  |  | 
|  | static int esp_slave_alloc(struct scsi_device *dev) | 
|  | { | 
|  | struct esp *esp = shost_priv(dev->host); | 
|  | struct esp_target_data *tp = &esp->target[dev->id]; | 
|  | struct esp_lun_data *lp; | 
|  |  | 
|  | lp = kzalloc(sizeof(*lp), GFP_KERNEL); | 
|  | if (!lp) | 
|  | return -ENOMEM; | 
|  | dev->hostdata = lp; | 
|  |  | 
|  | spi_min_period(tp->starget) = esp->min_period; | 
|  | spi_max_offset(tp->starget) = 15; | 
|  |  | 
|  | if (esp->flags & ESP_FLAG_WIDE_CAPABLE) | 
|  | spi_max_width(tp->starget) = 1; | 
|  | else | 
|  | spi_max_width(tp->starget) = 0; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int esp_slave_configure(struct scsi_device *dev) | 
|  | { | 
|  | struct esp *esp = shost_priv(dev->host); | 
|  | struct esp_target_data *tp = &esp->target[dev->id]; | 
|  | int goal_tags, queue_depth; | 
|  |  | 
|  | goal_tags = 0; | 
|  |  | 
|  | if (dev->tagged_supported) { | 
|  | /* XXX make this configurable somehow XXX */ | 
|  | goal_tags = ESP_DEFAULT_TAGS; | 
|  |  | 
|  | if (goal_tags > ESP_MAX_TAG) | 
|  | goal_tags = ESP_MAX_TAG; | 
|  | } | 
|  |  | 
|  | queue_depth = goal_tags; | 
|  | if (queue_depth < dev->host->cmd_per_lun) | 
|  | queue_depth = dev->host->cmd_per_lun; | 
|  |  | 
|  | if (goal_tags) { | 
|  | scsi_set_tag_type(dev, MSG_ORDERED_TAG); | 
|  | scsi_activate_tcq(dev, queue_depth); | 
|  | } else { | 
|  | scsi_deactivate_tcq(dev, queue_depth); | 
|  | } | 
|  | tp->flags |= ESP_TGT_DISCONNECT; | 
|  |  | 
|  | if (!spi_initial_dv(dev->sdev_target)) | 
|  | spi_dv_device(dev); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void esp_slave_destroy(struct scsi_device *dev) | 
|  | { | 
|  | struct esp_lun_data *lp = dev->hostdata; | 
|  |  | 
|  | kfree(lp); | 
|  | dev->hostdata = NULL; | 
|  | } | 
|  |  | 
|  | static int esp_eh_abort_handler(struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct esp *esp = shost_priv(cmd->device->host); | 
|  | struct esp_cmd_entry *ent, *tmp; | 
|  | struct completion eh_done; | 
|  | unsigned long flags; | 
|  |  | 
|  | /* XXX This helps a lot with debugging but might be a bit | 
|  | * XXX much for the final driver. | 
|  | */ | 
|  | spin_lock_irqsave(esp->host->host_lock, flags); | 
|  | printk(KERN_ERR PFX "esp%d: Aborting command [%p:%02x]\n", | 
|  | esp->host->unique_id, cmd, cmd->cmnd[0]); | 
|  | ent = esp->active_cmd; | 
|  | if (ent) | 
|  | printk(KERN_ERR PFX "esp%d: Current command [%p:%02x]\n", | 
|  | esp->host->unique_id, ent->cmd, ent->cmd->cmnd[0]); | 
|  | list_for_each_entry(ent, &esp->queued_cmds, list) { | 
|  | printk(KERN_ERR PFX "esp%d: Queued command [%p:%02x]\n", | 
|  | esp->host->unique_id, ent->cmd, ent->cmd->cmnd[0]); | 
|  | } | 
|  | list_for_each_entry(ent, &esp->active_cmds, list) { | 
|  | printk(KERN_ERR PFX "esp%d: Active command [%p:%02x]\n", | 
|  | esp->host->unique_id, ent->cmd, ent->cmd->cmnd[0]); | 
|  | } | 
|  | esp_dump_cmd_log(esp); | 
|  | spin_unlock_irqrestore(esp->host->host_lock, flags); | 
|  |  | 
|  | spin_lock_irqsave(esp->host->host_lock, flags); | 
|  |  | 
|  | ent = NULL; | 
|  | list_for_each_entry(tmp, &esp->queued_cmds, list) { | 
|  | if (tmp->cmd == cmd) { | 
|  | ent = tmp; | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | if (ent) { | 
|  | /* Easiest case, we didn't even issue the command | 
|  | * yet so it is trivial to abort. | 
|  | */ | 
|  | list_del(&ent->list); | 
|  |  | 
|  | cmd->result = DID_ABORT << 16; | 
|  | cmd->scsi_done(cmd); | 
|  |  | 
|  | esp_put_ent(esp, ent); | 
|  |  | 
|  | goto out_success; | 
|  | } | 
|  |  | 
|  | init_completion(&eh_done); | 
|  |  | 
|  | ent = esp->active_cmd; | 
|  | if (ent && ent->cmd == cmd) { | 
|  | /* Command is the currently active command on | 
|  | * the bus.  If we already have an output message | 
|  | * pending, no dice. | 
|  | */ | 
|  | if (esp->msg_out_len) | 
|  | goto out_failure; | 
|  |  | 
|  | /* Send out an abort, encouraging the target to | 
|  | * go to MSGOUT phase by asserting ATN. | 
|  | */ | 
|  | esp->msg_out[0] = ABORT_TASK_SET; | 
|  | esp->msg_out_len = 1; | 
|  | ent->eh_done = &eh_done; | 
|  |  | 
|  | scsi_esp_cmd(esp, ESP_CMD_SATN); | 
|  | } else { | 
|  | /* The command is disconnected.  This is not easy to | 
|  | * abort.  For now we fail and let the scsi error | 
|  | * handling layer go try a scsi bus reset or host | 
|  | * reset. | 
|  | * | 
|  | * What we could do is put together a scsi command | 
|  | * solely for the purpose of sending an abort message | 
|  | * to the target.  Coming up with all the code to | 
|  | * cook up scsi commands, special case them everywhere, | 
|  | * etc. is for questionable gain and it would be better | 
|  | * if the generic scsi error handling layer could do at | 
|  | * least some of that for us. | 
|  | * | 
|  | * Anyways this is an area for potential future improvement | 
|  | * in this driver. | 
|  | */ | 
|  | goto out_failure; | 
|  | } | 
|  |  | 
|  | spin_unlock_irqrestore(esp->host->host_lock, flags); | 
|  |  | 
|  | if (!wait_for_completion_timeout(&eh_done, 5 * HZ)) { | 
|  | spin_lock_irqsave(esp->host->host_lock, flags); | 
|  | ent->eh_done = NULL; | 
|  | spin_unlock_irqrestore(esp->host->host_lock, flags); | 
|  |  | 
|  | return FAILED; | 
|  | } | 
|  |  | 
|  | return SUCCESS; | 
|  |  | 
|  | out_success: | 
|  | spin_unlock_irqrestore(esp->host->host_lock, flags); | 
|  | return SUCCESS; | 
|  |  | 
|  | out_failure: | 
|  | /* XXX This might be a good location to set ESP_TGT_BROKEN | 
|  | * XXX since we know which target/lun in particular is | 
|  | * XXX causing trouble. | 
|  | */ | 
|  | spin_unlock_irqrestore(esp->host->host_lock, flags); | 
|  | return FAILED; | 
|  | } | 
|  |  | 
|  | static int esp_eh_bus_reset_handler(struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct esp *esp = shost_priv(cmd->device->host); | 
|  | struct completion eh_reset; | 
|  | unsigned long flags; | 
|  |  | 
|  | init_completion(&eh_reset); | 
|  |  | 
|  | spin_lock_irqsave(esp->host->host_lock, flags); | 
|  |  | 
|  | esp->eh_reset = &eh_reset; | 
|  |  | 
|  | /* XXX This is too simple... We should add lots of | 
|  | * XXX checks here so that if we find that the chip is | 
|  | * XXX very wedged we return failure immediately so | 
|  | * XXX that we can perform a full chip reset. | 
|  | */ | 
|  | esp->flags |= ESP_FLAG_RESETTING; | 
|  | scsi_esp_cmd(esp, ESP_CMD_RS); | 
|  |  | 
|  | spin_unlock_irqrestore(esp->host->host_lock, flags); | 
|  |  | 
|  | ssleep(esp_bus_reset_settle); | 
|  |  | 
|  | if (!wait_for_completion_timeout(&eh_reset, 5 * HZ)) { | 
|  | spin_lock_irqsave(esp->host->host_lock, flags); | 
|  | esp->eh_reset = NULL; | 
|  | spin_unlock_irqrestore(esp->host->host_lock, flags); | 
|  |  | 
|  | return FAILED; | 
|  | } | 
|  |  | 
|  | return SUCCESS; | 
|  | } | 
|  |  | 
|  | /* All bets are off, reset the entire device.  */ | 
|  | static int esp_eh_host_reset_handler(struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct esp *esp = shost_priv(cmd->device->host); | 
|  | unsigned long flags; | 
|  |  | 
|  | spin_lock_irqsave(esp->host->host_lock, flags); | 
|  | esp_bootup_reset(esp); | 
|  | esp_reset_cleanup(esp); | 
|  | spin_unlock_irqrestore(esp->host->host_lock, flags); | 
|  |  | 
|  | ssleep(esp_bus_reset_settle); | 
|  |  | 
|  | return SUCCESS; | 
|  | } | 
|  |  | 
|  | static const char *esp_info(struct Scsi_Host *host) | 
|  | { | 
|  | return "esp"; | 
|  | } | 
|  |  | 
|  | struct scsi_host_template scsi_esp_template = { | 
|  | .module			= THIS_MODULE, | 
|  | .name			= "esp", | 
|  | .info			= esp_info, | 
|  | .queuecommand		= esp_queuecommand, | 
|  | .target_alloc		= esp_target_alloc, | 
|  | .target_destroy		= esp_target_destroy, | 
|  | .slave_alloc		= esp_slave_alloc, | 
|  | .slave_configure	= esp_slave_configure, | 
|  | .slave_destroy		= esp_slave_destroy, | 
|  | .eh_abort_handler	= esp_eh_abort_handler, | 
|  | .eh_bus_reset_handler	= esp_eh_bus_reset_handler, | 
|  | .eh_host_reset_handler	= esp_eh_host_reset_handler, | 
|  | .can_queue		= 7, | 
|  | .this_id		= 7, | 
|  | .sg_tablesize		= SG_ALL, | 
|  | .use_clustering		= ENABLE_CLUSTERING, | 
|  | .max_sectors		= 0xffff, | 
|  | .skip_settle_delay	= 1, | 
|  | }; | 
|  | EXPORT_SYMBOL(scsi_esp_template); | 
|  |  | 
|  | static void esp_get_signalling(struct Scsi_Host *host) | 
|  | { | 
|  | struct esp *esp = shost_priv(host); | 
|  | enum spi_signal_type type; | 
|  |  | 
|  | if (esp->flags & ESP_FLAG_DIFFERENTIAL) | 
|  | type = SPI_SIGNAL_HVD; | 
|  | else | 
|  | type = SPI_SIGNAL_SE; | 
|  |  | 
|  | spi_signalling(host) = type; | 
|  | } | 
|  |  | 
|  | static void esp_set_offset(struct scsi_target *target, int offset) | 
|  | { | 
|  | struct Scsi_Host *host = dev_to_shost(target->dev.parent); | 
|  | struct esp *esp = shost_priv(host); | 
|  | struct esp_target_data *tp = &esp->target[target->id]; | 
|  |  | 
|  | if (esp->flags & ESP_FLAG_DISABLE_SYNC) | 
|  | tp->nego_goal_offset = 0; | 
|  | else | 
|  | tp->nego_goal_offset = offset; | 
|  | tp->flags |= ESP_TGT_CHECK_NEGO; | 
|  | } | 
|  |  | 
|  | static void esp_set_period(struct scsi_target *target, int period) | 
|  | { | 
|  | struct Scsi_Host *host = dev_to_shost(target->dev.parent); | 
|  | struct esp *esp = shost_priv(host); | 
|  | struct esp_target_data *tp = &esp->target[target->id]; | 
|  |  | 
|  | tp->nego_goal_period = period; | 
|  | tp->flags |= ESP_TGT_CHECK_NEGO; | 
|  | } | 
|  |  | 
|  | static void esp_set_width(struct scsi_target *target, int width) | 
|  | { | 
|  | struct Scsi_Host *host = dev_to_shost(target->dev.parent); | 
|  | struct esp *esp = shost_priv(host); | 
|  | struct esp_target_data *tp = &esp->target[target->id]; | 
|  |  | 
|  | tp->nego_goal_width = (width ? 1 : 0); | 
|  | tp->flags |= ESP_TGT_CHECK_NEGO; | 
|  | } | 
|  |  | 
|  | static struct spi_function_template esp_transport_ops = { | 
|  | .set_offset		= esp_set_offset, | 
|  | .show_offset		= 1, | 
|  | .set_period		= esp_set_period, | 
|  | .show_period		= 1, | 
|  | .set_width		= esp_set_width, | 
|  | .show_width		= 1, | 
|  | .get_signalling		= esp_get_signalling, | 
|  | }; | 
|  |  | 
|  | static int __init esp_init(void) | 
|  | { | 
|  | BUILD_BUG_ON(sizeof(struct scsi_pointer) < | 
|  | sizeof(struct esp_cmd_priv)); | 
|  |  | 
|  | esp_transport_template = spi_attach_transport(&esp_transport_ops); | 
|  | if (!esp_transport_template) | 
|  | return -ENODEV; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void __exit esp_exit(void) | 
|  | { | 
|  | spi_release_transport(esp_transport_template); | 
|  | } | 
|  |  | 
|  | MODULE_DESCRIPTION("ESP SCSI driver core"); | 
|  | MODULE_AUTHOR("David S. Miller (davem@davemloft.net)"); | 
|  | MODULE_LICENSE("GPL"); | 
|  | MODULE_VERSION(DRV_VERSION); | 
|  |  | 
|  | module_param(esp_bus_reset_settle, int, 0); | 
|  | MODULE_PARM_DESC(esp_bus_reset_settle, | 
|  | "ESP scsi bus reset delay in seconds"); | 
|  |  | 
|  | module_param(esp_debug, int, 0); | 
|  | MODULE_PARM_DESC(esp_debug, | 
|  | "ESP bitmapped debugging message enable value:\n" | 
|  | "	0x00000001	Log interrupt events\n" | 
|  | "	0x00000002	Log scsi commands\n" | 
|  | "	0x00000004	Log resets\n" | 
|  | "	0x00000008	Log message in events\n" | 
|  | "	0x00000010	Log message out events\n" | 
|  | "	0x00000020	Log command completion\n" | 
|  | "	0x00000040	Log disconnects\n" | 
|  | "	0x00000080	Log data start\n" | 
|  | "	0x00000100	Log data done\n" | 
|  | "	0x00000200	Log reconnects\n" | 
|  | "	0x00000400	Log auto-sense data\n" | 
|  | ); | 
|  |  | 
|  | module_init(esp_init); | 
|  | module_exit(esp_exit); |