iwlagn: open/close envlope to force move BT state machine
In uCode, BT state machine need to receive open envlope
command before perform calibration; followed by close envlope
command to move to next stage.
Since Linux has two separated uCode, one for init and the second
one for runtime; we use open envlope commands for init uCode to
indicate we are ready to perform calibration operation.
But for runtime uCode, we are not doing any init calibration,
so we issue open/close envlope commands to force uCode move to
"BT COEX ON" state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
diff --git a/drivers/net/wireless/iwlwifi/iwl-agn-ucode.c b/drivers/net/wireless/iwlwifi/iwl-agn-ucode.c
index a7961bf..8bfb049 100644
--- a/drivers/net/wireless/iwlwifi/iwl-agn-ucode.c
+++ b/drivers/net/wireless/iwlwifi/iwl-agn-ucode.c
@@ -307,6 +307,17 @@
goto restart;
}
+ if (priv->cfg->advanced_bt_coexist) {
+ /*
+ * Tell uCode we are ready to perform calibration
+ * need to perform this before any calibration
+ * no need to close the envlope since we are going
+ * to load the runtime uCode later.
+ */
+ iwlagn_send_bt_env(priv, IWL_BT_COEX_ENV_OPEN,
+ BT_COEX_PRIO_TBL_EVT_INIT_CALIB2);
+
+ }
iwlagn_send_calib_cfg(priv);
return;
@@ -364,7 +375,7 @@
0, 0, 0, 0, 0, 0, 0
};
-static void iwlagn_send_prio_tbl(struct iwl_priv *priv)
+void iwlagn_send_prio_tbl(struct iwl_priv *priv)
{
struct iwl_bt_coex_prio_table_cmd prio_tbl_cmd;
@@ -375,7 +386,7 @@
IWL_ERR(priv, "failed to send BT prio tbl command\n");
}
-static void iwlagn_send_bt_env(struct iwl_priv *priv, u8 action, u8 type)
+void iwlagn_send_bt_env(struct iwl_priv *priv, u8 action, u8 type)
{
struct iwl_bt_coex_prot_env_cmd env_cmd;
@@ -482,25 +493,6 @@
spin_unlock_irqrestore(&priv->lock, flags);
- if (priv->cfg->advanced_bt_coexist) {
- /* Configure Bluetooth device coexistence support */
- /* need to perform this before any calibration */
- priv->bt_valid = IWLAGN_BT_ALL_VALID_MSK;
- priv->kill_ack_mask = IWLAGN_BT_KILL_ACK_MASK_DEFAULT;
- priv->kill_cts_mask = IWLAGN_BT_KILL_CTS_MASK_DEFAULT;
- priv->cfg->ops->hcmd->send_bt_config(priv);
- priv->bt_valid = IWLAGN_BT_VALID_ENABLE_FLAGS;
-
- if (bt_coex_active && priv->iw_mode != NL80211_IFTYPE_ADHOC) {
- iwlagn_send_prio_tbl(priv);
- iwlagn_send_bt_env(priv, IWL_BT_COEX_ENV_OPEN,
- BT_COEX_PRIO_TBL_EVT_INIT_CALIB2);
- iwlagn_send_bt_env(priv, IWL_BT_COEX_ENV_CLOSE,
- BT_COEX_PRIO_TBL_EVT_INIT_CALIB2);
- }
-
- }
-
iwlagn_send_wimax_coex(priv);
iwlagn_set_Xtal_calib(priv);