| Kernel driver adm1021 |
| ===================== |
| |
| Supported chips: |
| * Analog Devices ADM1021 |
| Prefix: 'adm1021' |
| Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e |
| Datasheet: Publicly available at the Analog Devices website |
| * Analog Devices ADM1021A/ADM1023 |
| Prefix: 'adm1023' |
| Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e |
| Datasheet: Publicly available at the Analog Devices website |
| * Genesys Logic GL523SM |
| Prefix: 'gl523sm' |
| Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e |
| Datasheet: |
| * Intel Xeon Processor |
| Prefix: - any other - may require 'force_adm1021' parameter |
| Addresses scanned: none |
| Datasheet: Publicly available at Intel website |
| * Maxim MAX1617 |
| Prefix: 'max1617' |
| Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e |
| Datasheet: Publicly available at the Maxim website |
| * Maxim MAX1617A |
| Prefix: 'max1617a' |
| Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e |
| Datasheet: Publicly available at the Maxim website |
| * National Semiconductor LM84 |
| Prefix: 'lm84' |
| Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e |
| Datasheet: Publicly available at the National Semiconductor website |
| * Philips NE1617 |
| Prefix: 'max1617' (probably detected as a max1617) |
| Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e |
| Datasheet: Publicly available at the Philips website |
| * Philips NE1617A |
| Prefix: 'max1617' (probably detected as a max1617) |
| Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e |
| Datasheet: Publicly available at the Philips website |
| * TI THMC10 |
| Prefix: 'thmc10' |
| Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e |
| Datasheet: Publicly available at the TI website |
| * Onsemi MC1066 |
| Prefix: 'mc1066' |
| Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e |
| Datasheet: Publicly available at the Onsemi website |
| |
| |
| Authors: |
| Frodo Looijaard <frodol@dds.nl>, |
| Philip Edelbrock <phil@netroedge.com> |
| |
| Module Parameters |
| ----------------- |
| |
| * read_only: int |
| Don't set any values, read only mode |
| |
| |
| Description |
| ----------- |
| |
| The chips supported by this driver are very similar. The Maxim MAX1617 is |
| the oldest; it has the problem that it is not very well detectable. The |
| MAX1617A solves that. The ADM1021 is a straight clone of the MAX1617A. |
| Ditto for the THMC10. From here on, we will refer to all these chips as |
| ADM1021-clones. |
| |
| The ADM1021 and MAX1617A reports a die code, which is a sort of revision |
| code. This can help us pinpoint problems; it is not very useful |
| otherwise. |
| |
| ADM1021-clones implement two temperature sensors. One of them is internal, |
| and measures the temperature of the chip itself; the other is external and |
| is realised in the form of a transistor-like device. A special alarm |
| indicates whether the remote sensor is connected. |
| |
| Each sensor has its own low and high limits. When they are crossed, the |
| corresponding alarm is set and remains on as long as the temperature stays |
| out of range. Temperatures are measured in degrees Celsius. Measurements |
| are possible between -65 and +127 degrees, with a resolution of one degree. |
| |
| If an alarm triggers, it will remain triggered until the hardware register |
| is read at least once. This means that the cause for the alarm may already |
| have disappeared! |
| |
| This driver only updates its values each 1.5 seconds; reading it more often |
| will do no harm, but will return 'old' values. It is possible to make |
| ADM1021-clones do faster measurements, but there is really no good reason |
| for that. |
| |
| Xeon support |
| ------------ |
| |
| Some Xeon processors have real max1617, adm1021, or compatible chips |
| within them, with two temperature sensors. |
| |
| Other Xeons have chips with only one sensor. |
| |
| If you have a Xeon, and the adm1021 module loads, and both temperatures |
| appear valid, then things are good. |
| |
| If the adm1021 module doesn't load, you should try this: |
| modprobe adm1021 force_adm1021=BUS,ADDRESS |
| ADDRESS can only be 0x18, 0x1a, 0x29, 0x2b, 0x4c, or 0x4e. |
| |
| If you have dual Xeons you may have appear to have two separate |
| adm1021-compatible chips, or two single-temperature sensors, at distinct |
| addresses. |