drivers/net/atl1c/atl1c_hw.c - android_kernel_htc_msm8960 - Gitiles

 /*
  * Copyright(c) 2007 Atheros Corporation. All rights reserved.
  *
  * Derived from Intel e1000 driver
  * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the Free
  * Software Foundation; either version 2 of the License, or (at your option)
  * any later version.
  *
  * This program is distributed in the hope that it will be useful, but WITHOUT
  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  * more details.
  *
  * You should have received a copy of the GNU General Public License along with
  * this program; if not, write to the Free Software Foundation, Inc., 59
  * Temple Place - Suite 330, Boston, MA  02111-1307, USA.
  */
 #include <linux/pci.h>
 #include <linux/delay.h>
 #include <linux/mii.h>
 #include <linux/crc32.h>

 #include "atl1c.h"

 /*
  * check_eeprom_exist
  * return 1 if eeprom exist
  */
 int atl1c_check_eeprom_exist(struct atl1c_hw *hw)
 {
 	u32 data;

 	AT_READ_REG(hw, REG_TWSI_DEBUG, &data);
 	if (data & TWSI_DEBUG_DEV_EXIST)
 		return 1;

 	return 0;
 }

 void atl1c_hw_set_mac_addr(struct atl1c_hw *hw)
 {
 	u32 value;
 	/*
 	 * 00-0B-6A-F6-00-DC
 	 * 0:  6AF600DC 1: 000B
 	 * low dword
 	 */
 	value = (((u32)hw->mac_addr[2]) << 24) |
 		(((u32)hw->mac_addr[3]) << 16) |
 		(((u32)hw->mac_addr[4]) << 8)  |
 		(((u32)hw->mac_addr[5])) ;
 	AT_WRITE_REG_ARRAY(hw, REG_MAC_STA_ADDR, 0, value);
 	/* hight dword */
 	value = (((u32)hw->mac_addr[0]) << 8) |
 		(((u32)hw->mac_addr[1])) ;
 	AT_WRITE_REG_ARRAY(hw, REG_MAC_STA_ADDR, 1, value);
 }

 /*
  * atl1c_get_permanent_address
  * return 0 if get valid mac address,
  */
 static int atl1c_get_permanent_address(struct atl1c_hw *hw)
 {
 	u32 addr[2];
 	u32 i;
 	u32 otp_ctrl_data;
 	u32 twsi_ctrl_data;
 	u8  eth_addr[ETH_ALEN];

 	/* init */
 	addr[0] = addr[1] = 0;
 	AT_READ_REG(hw, REG_OTP_CTRL, &otp_ctrl_data);
 	if (atl1c_check_eeprom_exist(hw)) {
 		/* Enable OTP CLK */
 		if (!(otp_ctrl_data & OTP_CTRL_CLK_EN)) {
 			otp_ctrl_data |= OTP_CTRL_CLK_EN;
 			AT_WRITE_REG(hw, REG_OTP_CTRL, otp_ctrl_data);
 			AT_WRITE_FLUSH(hw);
 			msleep(1);
 		}

 		AT_READ_REG(hw, REG_TWSI_CTRL, &twsi_ctrl_data);
 		twsi_ctrl_data |= TWSI_CTRL_SW_LDSTART;
 		AT_WRITE_REG(hw, REG_TWSI_CTRL, twsi_ctrl_data);
 		for (i = 0; i < AT_TWSI_EEPROM_TIMEOUT; i++) {
 			msleep(10);
 			AT_READ_REG(hw, REG_TWSI_CTRL, &twsi_ctrl_data);
 			if ((twsi_ctrl_data & TWSI_CTRL_SW_LDSTART) == 0)
 				break;
 		}
 		if (i >= AT_TWSI_EEPROM_TIMEOUT)
 			return -1;
 	}
 	/* Disable OTP_CLK */
 	if (otp_ctrl_data & OTP_CTRL_CLK_EN) {
 		otp_ctrl_data &= ~OTP_CTRL_CLK_EN;
 		AT_WRITE_REG(hw, REG_OTP_CTRL, otp_ctrl_data);
 		AT_WRITE_FLUSH(hw);
 		msleep(1);
 	}

 	/* maybe MAC-address is from BIOS */
 	AT_READ_REG(hw, REG_MAC_STA_ADDR, &addr[0]);
 	AT_READ_REG(hw, REG_MAC_STA_ADDR + 4, &addr[1]);
 	*(u32 *) &eth_addr[2] = swab32(addr[0]);
 	*(u16 *) &eth_addr[0] = swab16(*(u16 *)&addr[1]);

 	if (is_valid_ether_addr(eth_addr)) {
 		memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
 		return 0;
 	}

 	return -1;
 }

 bool atl1c_read_eeprom(struct atl1c_hw *hw, u32 offset, u32 *p_value)
 {
 	int i;
 	int ret = false;
 	u32 otp_ctrl_data;
 	u32 control;
 	u32 data;

 	if (offset & 3)
 		return ret; /* address do not align */

 	AT_READ_REG(hw, REG_OTP_CTRL, &otp_ctrl_data);
 	if (!(otp_ctrl_data & OTP_CTRL_CLK_EN))
 		AT_WRITE_REG(hw, REG_OTP_CTRL,
 				(otp_ctrl_data | OTP_CTRL_CLK_EN));

 	AT_WRITE_REG(hw, REG_EEPROM_DATA_LO, 0);
 	control = (offset & EEPROM_CTRL_ADDR_MASK) << EEPROM_CTRL_ADDR_SHIFT;
 	AT_WRITE_REG(hw, REG_EEPROM_CTRL, control);

 	for (i = 0; i < 10; i++) {
 		udelay(100);
 		AT_READ_REG(hw, REG_EEPROM_CTRL, &control);
 		if (control & EEPROM_CTRL_RW)
 			break;
 	}
 	if (control & EEPROM_CTRL_RW) {
 		AT_READ_REG(hw, REG_EEPROM_CTRL, &data);
 		AT_READ_REG(hw, REG_EEPROM_DATA_LO, p_value);
 		data = data & 0xFFFF;
 		*p_value = swab32((data << 16) | (*p_value >> 16));
 		ret = true;
 	}
 	if (!(otp_ctrl_data & OTP_CTRL_CLK_EN))
 		AT_WRITE_REG(hw, REG_OTP_CTRL, otp_ctrl_data);

 	return ret;
 }
 /*
  * Reads the adapter's MAC address from the EEPROM
  *
  * hw - Struct containing variables accessed by shared code
  */
 int atl1c_read_mac_addr(struct atl1c_hw *hw)
 {
 	int err = 0;

 	err = atl1c_get_permanent_address(hw);
 	if (err)
 		random_ether_addr(hw->perm_mac_addr);

 	memcpy(hw->mac_addr, hw->perm_mac_addr, sizeof(hw->perm_mac_addr));
 	return 0;
 }

 /*
  * atl1c_hash_mc_addr
  *  purpose
  *      set hash value for a multicast address
  *      hash calcu processing :
  *          1. calcu 32bit CRC for multicast address
  *          2. reverse crc with MSB to LSB
  */
 u32 atl1c_hash_mc_addr(struct atl1c_hw *hw, u8 *mc_addr)
 {
 	u32 crc32;
 	u32 value = 0;
 	int i;

 	crc32 = ether_crc_le(6, mc_addr);
 	for (i = 0; i < 32; i++)
 		value |= (((crc32 >> i) & 1) << (31 - i));

 	return value;
 }

 /*
  * Sets the bit in the multicast table corresponding to the hash value.
  * hw - Struct containing variables accessed by shared code
  * hash_value - Multicast address hash value
  */
 void atl1c_hash_set(struct atl1c_hw *hw, u32 hash_value)
 {
 	u32 hash_bit, hash_reg;
 	u32 mta;

 	/*
 	 * The HASH Table  is a register array of 2 32-bit registers.
 	 * It is treated like an array of 64 bits.  We want to set
 	 * bit BitArray[hash_value]. So we figure out what register
 	 * the bit is in, read it, OR in the new bit, then write
 	 * back the new value.  The register is determined by the
 	 * upper bit of the hash value and the bit within that
 	 * register are determined by the lower 5 bits of the value.
 	 */
 	hash_reg = (hash_value >> 31) & 0x1;
 	hash_bit = (hash_value >> 26) & 0x1F;

 	mta = AT_READ_REG_ARRAY(hw, REG_RX_HASH_TABLE, hash_reg);

 	mta |= (1 << hash_bit);

 	AT_WRITE_REG_ARRAY(hw, REG_RX_HASH_TABLE, hash_reg, mta);
 }

 /*
  * Reads the value from a PHY register
  * hw - Struct containing variables accessed by shared code
  * reg_addr - address of the PHY register to read
  */
 int atl1c_read_phy_reg(struct atl1c_hw *hw, u16 reg_addr, u16 *phy_data)
 {
 	u32 val;
 	int i;

 	val = ((u32)(reg_addr & MDIO_REG_ADDR_MASK)) << MDIO_REG_ADDR_SHIFT |
 		MDIO_START | MDIO_SUP_PREAMBLE | MDIO_RW |
 		MDIO_CLK_25_4 << MDIO_CLK_SEL_SHIFT;

 	AT_WRITE_REG(hw, REG_MDIO_CTRL, val);

 	for (i = 0; i < MDIO_WAIT_TIMES; i++) {
 		udelay(2);
 		AT_READ_REG(hw, REG_MDIO_CTRL, &val);
 		if (!(val & (MDIO_START | MDIO_BUSY)))
 			break;
 	}
 	if (!(val & (MDIO_START | MDIO_BUSY))) {
 		*phy_data = (u16)val;
 		return 0;
 	}

 	return -1;
 }

 /*
  * Writes a value to a PHY register
  * hw - Struct containing variables accessed by shared code
  * reg_addr - address of the PHY register to write
  * data - data to write to the PHY
  */
 int atl1c_write_phy_reg(struct atl1c_hw *hw, u32 reg_addr, u16 phy_data)
 {
 	int i;
 	u32 val;

 	val = ((u32)(phy_data & MDIO_DATA_MASK)) << MDIO_DATA_SHIFT   |
 	       (reg_addr & MDIO_REG_ADDR_MASK) << MDIO_REG_ADDR_SHIFT |
 	       MDIO_SUP_PREAMBLE | MDIO_START |
 	       MDIO_CLK_25_4 << MDIO_CLK_SEL_SHIFT;

 	AT_WRITE_REG(hw, REG_MDIO_CTRL, val);

 	for (i = 0; i < MDIO_WAIT_TIMES; i++) {
 		udelay(2);
 		AT_READ_REG(hw, REG_MDIO_CTRL, &val);
 		if (!(val & (MDIO_START | MDIO_BUSY)))
 			break;
 	}

 	if (!(val & (MDIO_START | MDIO_BUSY)))
 		return 0;

 	return -1;
 }

 /*
  * Configures PHY autoneg and flow control advertisement settings
  *
  * hw - Struct containing variables accessed by shared code
  */
 static int atl1c_phy_setup_adv(struct atl1c_hw *hw)
 {
 	u16 mii_adv_data = ADVERTISE_DEFAULT_CAP & ~ADVERTISE_SPEED_MASK;
 	u16 mii_giga_ctrl_data = GIGA_CR_1000T_DEFAULT_CAP &
 				~GIGA_CR_1000T_SPEED_MASK;

 	if (hw->autoneg_advertised & ADVERTISED_10baseT_Half)
 		mii_adv_data |= ADVERTISE_10HALF;
 	if (hw->autoneg_advertised & ADVERTISED_10baseT_Full)
 		mii_adv_data |= ADVERTISE_10FULL;
 	if (hw->autoneg_advertised & ADVERTISED_100baseT_Half)
 		mii_adv_data |= ADVERTISE_100HALF;
 	if (hw->autoneg_advertised & ADVERTISED_100baseT_Full)
 		mii_adv_data |= ADVERTISE_100FULL;

 	if (hw->autoneg_advertised & ADVERTISED_Autoneg)
 		mii_adv_data |= ADVERTISE_10HALF  | ADVERTISE_10FULL |
 				ADVERTISE_100HALF | ADVERTISE_100FULL;

 	if (hw->ctrl_flags & ATL1C_LINK_CAP_1000M) {
 		if (hw->autoneg_advertised & ADVERTISED_1000baseT_Half)
 			mii_giga_ctrl_data |= ADVERTISE_1000HALF;
 		if (hw->autoneg_advertised & ADVERTISED_1000baseT_Full)
 			mii_giga_ctrl_data |= ADVERTISE_1000FULL;
 		if (hw->autoneg_advertised & ADVERTISED_Autoneg)
 			mii_giga_ctrl_data |= ADVERTISE_1000HALF |
 					ADVERTISE_1000FULL;
 	}

 	if (atl1c_write_phy_reg(hw, MII_ADVERTISE, mii_adv_data) != 0 ||
 	    atl1c_write_phy_reg(hw, MII_GIGA_CR, mii_giga_ctrl_data) != 0)
 		return -1;
 	return 0;
 }

 void atl1c_phy_disable(struct atl1c_hw *hw)
 {
 	AT_WRITE_REGW(hw, REG_GPHY_CTRL,
 			GPHY_CTRL_PW_WOL_DIS | GPHY_CTRL_EXT_RESET);
 }

 static void atl1c_phy_magic_data(struct atl1c_hw *hw)
 {
 	u16 data;

 	data = ANA_LOOP_SEL_10BT | ANA_EN_MASK_TB | ANA_EN_10BT_IDLE |
 		((1 & ANA_INTERVAL_SEL_TIMER_MASK) <<
 		ANA_INTERVAL_SEL_TIMER_SHIFT);

 	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_18);
 	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

 	data = (2 & ANA_SERDES_CDR_BW_MASK) | ANA_MS_PAD_DBG |
 		ANA_SERDES_EN_DEEM | ANA_SERDES_SEL_HSP | ANA_SERDES_EN_PLL |
 		ANA_SERDES_EN_LCKDT;

 	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_5);
 	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

 	data = (44 & ANA_LONG_CABLE_TH_100_MASK) |
 		((33 & ANA_SHORT_CABLE_TH_100_MASK) <<
 		ANA_SHORT_CABLE_TH_100_SHIFT) | ANA_BP_BAD_LINK_ACCUM |
 		ANA_BP_SMALL_BW;

 	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_54);
 	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

 	data = (11 & ANA_IECHO_ADJ_MASK) | ((11 & ANA_IECHO_ADJ_MASK) <<
 		ANA_IECHO_ADJ_2_SHIFT) | ((8 & ANA_IECHO_ADJ_MASK) <<
 		ANA_IECHO_ADJ_1_SHIFT) | ((8 & ANA_IECHO_ADJ_MASK) <<
 		ANA_IECHO_ADJ_0_SHIFT);

 	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_4);
 	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

 	data = ANA_RESTART_CAL | ((7 & ANA_MANUL_SWICH_ON_MASK) <<
 		ANA_MANUL_SWICH_ON_SHIFT) | ANA_MAN_ENABLE |
 		ANA_SEL_HSP | ANA_EN_HB | ANA_OEN_125M;

 	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_0);
 	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

 	if (hw->ctrl_flags & ATL1C_HIB_DISABLE) {
 		atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_41);
 		if (atl1c_read_phy_reg(hw, MII_DBG_DATA, &data) != 0)
 			return;
 		data &= ~ANA_TOP_PS_EN;
 		atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

 		atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_11);
 		if (atl1c_read_phy_reg(hw, MII_DBG_DATA, &data) != 0)
 			return;
 		data &= ~ANA_PS_HIB_EN;
 		atl1c_write_phy_reg(hw, MII_DBG_DATA, data);
 	}
 }

 int atl1c_phy_reset(struct atl1c_hw *hw)
 {
 	struct atl1c_adapter *adapter = hw->adapter;
 	struct pci_dev *pdev = adapter->pdev;
 	u32 phy_ctrl_data = GPHY_CTRL_DEFAULT;
 	u32 mii_ier_data = IER_LINK_UP | IER_LINK_DOWN;
 	int err;

 	if (hw->ctrl_flags & ATL1C_HIB_DISABLE)
 		phy_ctrl_data &= ~GPHY_CTRL_HIB_EN;

 	AT_WRITE_REG(hw, REG_GPHY_CTRL, phy_ctrl_data);
 	AT_WRITE_FLUSH(hw);
 	msleep(40);
 	phy_ctrl_data |= GPHY_CTRL_EXT_RESET;
 	AT_WRITE_REG(hw, REG_GPHY_CTRL, phy_ctrl_data);
 	AT_WRITE_FLUSH(hw);
 	msleep(10);

 	/*Enable PHY LinkChange Interrupt */
 	err = atl1c_write_phy_reg(hw, MII_IER, mii_ier_data);
 	if (err) {
 		if (netif_msg_hw(adapter))
 			dev_err(&pdev->dev,
 				"Error enable PHY linkChange Interrupt\n");
 		return err;
 	}
 	if (!(hw->ctrl_flags & ATL1C_FPGA_VERSION))
 		atl1c_phy_magic_data(hw);
 	return 0;
 }

 int atl1c_phy_init(struct atl1c_hw *hw)
 {
 	struct atl1c_adapter *adapter = (struct atl1c_adapter *)hw->adapter;
 	struct pci_dev *pdev = adapter->pdev;
 	int ret_val;
 	u16 mii_bmcr_data = BMCR_RESET;
 	u16 phy_id1, phy_id2;

 	if ((atl1c_read_phy_reg(hw, MII_PHYSID1, &phy_id1) != 0) ||
 		(atl1c_read_phy_reg(hw, MII_PHYSID2, &phy_id2) != 0)) {
 			if (netif_msg_link(adapter))
 				dev_err(&pdev->dev, "Error get phy ID\n");
 		return -1;
 	}
 	switch (hw->media_type) {
 	case MEDIA_TYPE_AUTO_SENSOR:
 		ret_val = atl1c_phy_setup_adv(hw);
 		if (ret_val) {
 			if (netif_msg_link(adapter))
 				dev_err(&pdev->dev,
 					"Error Setting up Auto-Negotiation\n");
 			return ret_val;
 		}
 		mii_bmcr_data |= BMCR_AUTO_NEG_EN | BMCR_RESTART_AUTO_NEG;
 		break;
 	case MEDIA_TYPE_100M_FULL:
 		mii_bmcr_data |= BMCR_SPEED_100 | BMCR_FULL_DUPLEX;
 		break;
 	case MEDIA_TYPE_100M_HALF:
 		mii_bmcr_data |= BMCR_SPEED_100;
 		break;
 	case MEDIA_TYPE_10M_FULL:
 		mii_bmcr_data |= BMCR_SPEED_10 | BMCR_FULL_DUPLEX;
 		break;
 	case MEDIA_TYPE_10M_HALF:
 		mii_bmcr_data |= BMCR_SPEED_10;
 		break;
 	default:
 		if (netif_msg_link(adapter))
 			dev_err(&pdev->dev, "Wrong Media type %d\n",
 				hw->media_type);
 		return -1;
 		break;
 	}

 	ret_val = atl1c_write_phy_reg(hw, MII_BMCR, mii_bmcr_data);
 	if (ret_val)
 		return ret_val;
 	hw->phy_configured = true;

 	return 0;
 }

 /*
  * Detects the current speed and duplex settings of the hardware.
  *
  * hw - Struct containing variables accessed by shared code
  * speed - Speed of the connection
  * duplex - Duplex setting of the connection
  */
 int atl1c_get_speed_and_duplex(struct atl1c_hw *hw, u16 *speed, u16 *duplex)
 {
 	int err;
 	u16 phy_data;

 	/* Read   PHY Specific Status Register (17) */
 	err = atl1c_read_phy_reg(hw, MII_GIGA_PSSR, &phy_data);
 	if (err)
 		return err;

 	if (!(phy_data & GIGA_PSSR_SPD_DPLX_RESOLVED))
 		return -1;

 	switch (phy_data & GIGA_PSSR_SPEED) {
 	case GIGA_PSSR_1000MBS:
 		*speed = SPEED_1000;
 		break;
 	case GIGA_PSSR_100MBS:
 		*speed = SPEED_100;
 		break;
 	case  GIGA_PSSR_10MBS:
 		*speed = SPEED_10;
 		break;
 	default:
 		return -1;
 		break;
 	}

 	if (phy_data & GIGA_PSSR_DPLX)
 		*duplex = FULL_DUPLEX;
 	else
 		*duplex = HALF_DUPLEX;

 	return 0;
 }

 int atl1c_restart_autoneg(struct atl1c_hw *hw)
 {
 	int err = 0;
 	u16 mii_bmcr_data = BMCR_RESET;

 	err = atl1c_phy_setup_adv(hw);
 	if (err)
 		return err;
 	mii_bmcr_data |= BMCR_AUTO_NEG_EN | BMCR_RESTART_AUTO_NEG;

 	return atl1c_write_phy_reg(hw, MII_BMCR, mii_bmcr_data);
 }
	/*
	* Copyright(c) 2007 Atheros Corporation. All rights reserved.
	*
	* Derived from Intel e1000 driver
	* Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
	*
	* This program is free software; you can redistribute it and/or modify it
	* under the terms of the GNU General Public License as published by the Free
	* Software Foundation; either version 2 of the License, or (at your option)
	* any later version.
	*
	* This program is distributed in the hope that it will be useful, but WITHOUT
	* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
	* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
	* more details.
	*
	* You should have received a copy of the GNU General Public License along with
	* this program; if not, write to the Free Software Foundation, Inc., 59
	* Temple Place - Suite 330, Boston, MA 02111-1307, USA.
	*/
	#include <linux/pci.h>
	#include <linux/delay.h>
	#include <linux/mii.h>
	#include <linux/crc32.h>

	#include "atl1c.h"

	/*
	* check_eeprom_exist
	* return 1 if eeprom exist
	*/
	int atl1c_check_eeprom_exist(struct atl1c_hw *hw)
	{
	u32 data;

	AT_READ_REG(hw, REG_TWSI_DEBUG, &data);
	if (data & TWSI_DEBUG_DEV_EXIST)
	return 1;

	return 0;
	}

	void atl1c_hw_set_mac_addr(struct atl1c_hw *hw)
	{
	u32 value;
	/*
	* 00-0B-6A-F6-00-DC
	* 0: 6AF600DC 1: 000B
	* low dword
	*/
	value = (((u32)hw->mac_addr[2]) << 24) \|
	(((u32)hw->mac_addr[3]) << 16) \|
	(((u32)hw->mac_addr[4]) << 8) \|
	(((u32)hw->mac_addr[5])) ;
	AT_WRITE_REG_ARRAY(hw, REG_MAC_STA_ADDR, 0, value);
	/* hight dword */
	value = (((u32)hw->mac_addr[0]) << 8) \|
	(((u32)hw->mac_addr[1])) ;
	AT_WRITE_REG_ARRAY(hw, REG_MAC_STA_ADDR, 1, value);
	}

	/*
	* atl1c_get_permanent_address
	* return 0 if get valid mac address,
	*/
	static int atl1c_get_permanent_address(struct atl1c_hw *hw)
	{
	u32 addr[2];
	u32 i;
	u32 otp_ctrl_data;
	u32 twsi_ctrl_data;
	u8 eth_addr[ETH_ALEN];

	/* init */
	addr[0] = addr[1] = 0;
	AT_READ_REG(hw, REG_OTP_CTRL, &otp_ctrl_data);
	if (atl1c_check_eeprom_exist(hw)) {
	/* Enable OTP CLK */
	if (!(otp_ctrl_data & OTP_CTRL_CLK_EN)) {
	otp_ctrl_data \|= OTP_CTRL_CLK_EN;
	AT_WRITE_REG(hw, REG_OTP_CTRL, otp_ctrl_data);
	AT_WRITE_FLUSH(hw);
	msleep(1);
	}

	AT_READ_REG(hw, REG_TWSI_CTRL, &twsi_ctrl_data);
	twsi_ctrl_data \|= TWSI_CTRL_SW_LDSTART;
	AT_WRITE_REG(hw, REG_TWSI_CTRL, twsi_ctrl_data);
	for (i = 0; i < AT_TWSI_EEPROM_TIMEOUT; i++) {
	msleep(10);
	AT_READ_REG(hw, REG_TWSI_CTRL, &twsi_ctrl_data);
	if ((twsi_ctrl_data & TWSI_CTRL_SW_LDSTART) == 0)
	break;
	}
	if (i >= AT_TWSI_EEPROM_TIMEOUT)
	return -1;
	}
	/* Disable OTP_CLK */
	if (otp_ctrl_data & OTP_CTRL_CLK_EN) {
	otp_ctrl_data &= ~OTP_CTRL_CLK_EN;
	AT_WRITE_REG(hw, REG_OTP_CTRL, otp_ctrl_data);
	AT_WRITE_FLUSH(hw);
	msleep(1);
	}

	/* maybe MAC-address is from BIOS */
	AT_READ_REG(hw, REG_MAC_STA_ADDR, &addr[0]);
	AT_READ_REG(hw, REG_MAC_STA_ADDR + 4, &addr[1]);
	(u32 ) &eth_addr[2] = swab32(addr[0]);
	(u16 ) &eth_addr[0] = swab16((u16 )&addr[1]);

	if (is_valid_ether_addr(eth_addr)) {
	memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
	return 0;
	}

	return -1;
	}

	bool atl1c_read_eeprom(struct atl1c_hw hw, u32 offset, u32 p_value)
	{
	int i;
	int ret = false;
	u32 otp_ctrl_data;
	u32 control;
	u32 data;

	if (offset & 3)
	return ret; /* address do not align */

	AT_READ_REG(hw, REG_OTP_CTRL, &otp_ctrl_data);
	if (!(otp_ctrl_data & OTP_CTRL_CLK_EN))
	AT_WRITE_REG(hw, REG_OTP_CTRL,
	(otp_ctrl_data \| OTP_CTRL_CLK_EN));

	AT_WRITE_REG(hw, REG_EEPROM_DATA_LO, 0);
	control = (offset & EEPROM_CTRL_ADDR_MASK) << EEPROM_CTRL_ADDR_SHIFT;
	AT_WRITE_REG(hw, REG_EEPROM_CTRL, control);

	for (i = 0; i < 10; i++) {
	udelay(100);
	AT_READ_REG(hw, REG_EEPROM_CTRL, &control);
	if (control & EEPROM_CTRL_RW)
	break;
	}
	if (control & EEPROM_CTRL_RW) {
	AT_READ_REG(hw, REG_EEPROM_CTRL, &data);
	AT_READ_REG(hw, REG_EEPROM_DATA_LO, p_value);
	data = data & 0xFFFF;
	p_value = swab32((data << 16) \| (p_value >> 16));
	ret = true;
	}
	if (!(otp_ctrl_data & OTP_CTRL_CLK_EN))
	AT_WRITE_REG(hw, REG_OTP_CTRL, otp_ctrl_data);

	return ret;
	}
	/*
	* Reads the adapter's MAC address from the EEPROM
	*
	* hw - Struct containing variables accessed by shared code
	*/
	int atl1c_read_mac_addr(struct atl1c_hw *hw)
	{
	int err = 0;

	err = atl1c_get_permanent_address(hw);
	if (err)
	random_ether_addr(hw->perm_mac_addr);

	memcpy(hw->mac_addr, hw->perm_mac_addr, sizeof(hw->perm_mac_addr));
	return 0;
	}

	/*
	* atl1c_hash_mc_addr
	* purpose
	* set hash value for a multicast address
	* hash calcu processing :
	* 1. calcu 32bit CRC for multicast address
	* 2. reverse crc with MSB to LSB
	*/
	u32 atl1c_hash_mc_addr(struct atl1c_hw hw, u8 mc_addr)
	{
	u32 crc32;
	u32 value = 0;
	int i;

	crc32 = ether_crc_le(6, mc_addr);
	for (i = 0; i < 32; i++)
	value \|= (((crc32 >> i) & 1) << (31 - i));

	return value;
	}

	/*
	* Sets the bit in the multicast table corresponding to the hash value.
	* hw - Struct containing variables accessed by shared code
	* hash_value - Multicast address hash value
	*/
	void atl1c_hash_set(struct atl1c_hw *hw, u32 hash_value)
	{
	u32 hash_bit, hash_reg;
	u32 mta;

	/*
	* The HASH Table is a register array of 2 32-bit registers.
	* It is treated like an array of 64 bits. We want to set
	* bit BitArray[hash_value]. So we figure out what register
	* the bit is in, read it, OR in the new bit, then write
	* back the new value. The register is determined by the
	* upper bit of the hash value and the bit within that
	* register are determined by the lower 5 bits of the value.
	*/
	hash_reg = (hash_value >> 31) & 0x1;
	hash_bit = (hash_value >> 26) & 0x1F;

	mta = AT_READ_REG_ARRAY(hw, REG_RX_HASH_TABLE, hash_reg);

	mta \|= (1 << hash_bit);

	AT_WRITE_REG_ARRAY(hw, REG_RX_HASH_TABLE, hash_reg, mta);
	}

	/*
	* Reads the value from a PHY register
	* hw - Struct containing variables accessed by shared code
	* reg_addr - address of the PHY register to read
	*/
	int atl1c_read_phy_reg(struct atl1c_hw hw, u16 reg_addr, u16 phy_data)
	{
	u32 val;
	int i;

	val = ((u32)(reg_addr & MDIO_REG_ADDR_MASK)) << MDIO_REG_ADDR_SHIFT \|
	MDIO_START \| MDIO_SUP_PREAMBLE \| MDIO_RW \|
	MDIO_CLK_25_4 << MDIO_CLK_SEL_SHIFT;

	AT_WRITE_REG(hw, REG_MDIO_CTRL, val);

	for (i = 0; i < MDIO_WAIT_TIMES; i++) {
	udelay(2);
	AT_READ_REG(hw, REG_MDIO_CTRL, &val);
	if (!(val & (MDIO_START \| MDIO_BUSY)))
	break;
	}
	if (!(val & (MDIO_START \| MDIO_BUSY))) {
	*phy_data = (u16)val;
	return 0;
	}

	return -1;
	}

	/*
	* Writes a value to a PHY register
	* hw - Struct containing variables accessed by shared code
	* reg_addr - address of the PHY register to write
	* data - data to write to the PHY
	*/
	int atl1c_write_phy_reg(struct atl1c_hw *hw, u32 reg_addr, u16 phy_data)
	{
	int i;
	u32 val;

	val = ((u32)(phy_data & MDIO_DATA_MASK)) << MDIO_DATA_SHIFT \|
	(reg_addr & MDIO_REG_ADDR_MASK) << MDIO_REG_ADDR_SHIFT \|
	MDIO_SUP_PREAMBLE \| MDIO_START \|
	MDIO_CLK_25_4 << MDIO_CLK_SEL_SHIFT;

	AT_WRITE_REG(hw, REG_MDIO_CTRL, val);

	for (i = 0; i < MDIO_WAIT_TIMES; i++) {
	udelay(2);
	AT_READ_REG(hw, REG_MDIO_CTRL, &val);
	if (!(val & (MDIO_START \| MDIO_BUSY)))
	break;
	}

	if (!(val & (MDIO_START \| MDIO_BUSY)))
	return 0;

	return -1;
	}

	/*
	* Configures PHY autoneg and flow control advertisement settings
	*
	* hw - Struct containing variables accessed by shared code
	*/
	static int atl1c_phy_setup_adv(struct atl1c_hw *hw)
	{
	u16 mii_adv_data = ADVERTISE_DEFAULT_CAP & ~ADVERTISE_SPEED_MASK;
	u16 mii_giga_ctrl_data = GIGA_CR_1000T_DEFAULT_CAP &
	~GIGA_CR_1000T_SPEED_MASK;

	if (hw->autoneg_advertised & ADVERTISED_10baseT_Half)
	mii_adv_data \|= ADVERTISE_10HALF;
	if (hw->autoneg_advertised & ADVERTISED_10baseT_Full)
	mii_adv_data \|= ADVERTISE_10FULL;
	if (hw->autoneg_advertised & ADVERTISED_100baseT_Half)
	mii_adv_data \|= ADVERTISE_100HALF;
	if (hw->autoneg_advertised & ADVERTISED_100baseT_Full)
	mii_adv_data \|= ADVERTISE_100FULL;

	if (hw->autoneg_advertised & ADVERTISED_Autoneg)
	mii_adv_data \|= ADVERTISE_10HALF \| ADVERTISE_10FULL \|
	ADVERTISE_100HALF \| ADVERTISE_100FULL;

	if (hw->ctrl_flags & ATL1C_LINK_CAP_1000M) {
	if (hw->autoneg_advertised & ADVERTISED_1000baseT_Half)
	mii_giga_ctrl_data \|= ADVERTISE_1000HALF;
	if (hw->autoneg_advertised & ADVERTISED_1000baseT_Full)
	mii_giga_ctrl_data \|= ADVERTISE_1000FULL;
	if (hw->autoneg_advertised & ADVERTISED_Autoneg)
	mii_giga_ctrl_data \|= ADVERTISE_1000HALF \|
	ADVERTISE_1000FULL;
	}

	if (atl1c_write_phy_reg(hw, MII_ADVERTISE, mii_adv_data) != 0 \|\|
	atl1c_write_phy_reg(hw, MII_GIGA_CR, mii_giga_ctrl_data) != 0)
	return -1;
	return 0;
	}

	void atl1c_phy_disable(struct atl1c_hw *hw)
	{
	AT_WRITE_REGW(hw, REG_GPHY_CTRL,
	GPHY_CTRL_PW_WOL_DIS \| GPHY_CTRL_EXT_RESET);
	}

	static void atl1c_phy_magic_data(struct atl1c_hw *hw)
	{
	u16 data;

	data = ANA_LOOP_SEL_10BT \| ANA_EN_MASK_TB \| ANA_EN_10BT_IDLE \|
	((1 & ANA_INTERVAL_SEL_TIMER_MASK) <<
	ANA_INTERVAL_SEL_TIMER_SHIFT);

	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_18);
	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

	data = (2 & ANA_SERDES_CDR_BW_MASK) \| ANA_MS_PAD_DBG \|
	ANA_SERDES_EN_DEEM \| ANA_SERDES_SEL_HSP \| ANA_SERDES_EN_PLL \|
	ANA_SERDES_EN_LCKDT;

	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_5);
	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

	data = (44 & ANA_LONG_CABLE_TH_100_MASK) \|
	((33 & ANA_SHORT_CABLE_TH_100_MASK) <<
	ANA_SHORT_CABLE_TH_100_SHIFT) \| ANA_BP_BAD_LINK_ACCUM \|
	ANA_BP_SMALL_BW;

	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_54);
	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

	data = (11 & ANA_IECHO_ADJ_MASK) \| ((11 & ANA_IECHO_ADJ_MASK) <<
	ANA_IECHO_ADJ_2_SHIFT) \| ((8 & ANA_IECHO_ADJ_MASK) <<
	ANA_IECHO_ADJ_1_SHIFT) \| ((8 & ANA_IECHO_ADJ_MASK) <<
	ANA_IECHO_ADJ_0_SHIFT);

	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_4);
	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

	data = ANA_RESTART_CAL \| ((7 & ANA_MANUL_SWICH_ON_MASK) <<
	ANA_MANUL_SWICH_ON_SHIFT) \| ANA_MAN_ENABLE \|
	ANA_SEL_HSP \| ANA_EN_HB \| ANA_OEN_125M;

	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_0);
	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

	if (hw->ctrl_flags & ATL1C_HIB_DISABLE) {
	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_41);
	if (atl1c_read_phy_reg(hw, MII_DBG_DATA, &data) != 0)
	return;
	data &= ~ANA_TOP_PS_EN;
	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);

	atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_11);
	if (atl1c_read_phy_reg(hw, MII_DBG_DATA, &data) != 0)
	return;
	data &= ~ANA_PS_HIB_EN;
	atl1c_write_phy_reg(hw, MII_DBG_DATA, data);
	}
	}

	int atl1c_phy_reset(struct atl1c_hw *hw)
	{
	struct atl1c_adapter *adapter = hw->adapter;
	struct pci_dev *pdev = adapter->pdev;
	u32 phy_ctrl_data = GPHY_CTRL_DEFAULT;
	u32 mii_ier_data = IER_LINK_UP \| IER_LINK_DOWN;
	int err;

	if (hw->ctrl_flags & ATL1C_HIB_DISABLE)
	phy_ctrl_data &= ~GPHY_CTRL_HIB_EN;

	AT_WRITE_REG(hw, REG_GPHY_CTRL, phy_ctrl_data);
	AT_WRITE_FLUSH(hw);
	msleep(40);
	phy_ctrl_data \|= GPHY_CTRL_EXT_RESET;
	AT_WRITE_REG(hw, REG_GPHY_CTRL, phy_ctrl_data);
	AT_WRITE_FLUSH(hw);
	msleep(10);

	/Enable PHY LinkChange Interrupt /
	err = atl1c_write_phy_reg(hw, MII_IER, mii_ier_data);
	if (err) {
	if (netif_msg_hw(adapter))
	dev_err(&pdev->dev,
	"Error enable PHY linkChange Interrupt\n");
	return err;
	}
	if (!(hw->ctrl_flags & ATL1C_FPGA_VERSION))
	atl1c_phy_magic_data(hw);
	return 0;
	}

	int atl1c_phy_init(struct atl1c_hw *hw)
	{
	struct atl1c_adapter adapter = (struct atl1c_adapter )hw->adapter;
	struct pci_dev *pdev = adapter->pdev;
	int ret_val;
	u16 mii_bmcr_data = BMCR_RESET;
	u16 phy_id1, phy_id2;

	if ((atl1c_read_phy_reg(hw, MII_PHYSID1, &phy_id1) != 0) \|\|
	(atl1c_read_phy_reg(hw, MII_PHYSID2, &phy_id2) != 0)) {
	if (netif_msg_link(adapter))
	dev_err(&pdev->dev, "Error get phy ID\n");
	return -1;
	}
	switch (hw->media_type) {
	case MEDIA_TYPE_AUTO_SENSOR:
	ret_val = atl1c_phy_setup_adv(hw);
	if (ret_val) {
	if (netif_msg_link(adapter))
	dev_err(&pdev->dev,
	"Error Setting up Auto-Negotiation\n");
	return ret_val;
	}
	mii_bmcr_data \|= BMCR_AUTO_NEG_EN \| BMCR_RESTART_AUTO_NEG;
	break;
	case MEDIA_TYPE_100M_FULL:
	mii_bmcr_data \|= BMCR_SPEED_100 \| BMCR_FULL_DUPLEX;
	break;
	case MEDIA_TYPE_100M_HALF:
	mii_bmcr_data \|= BMCR_SPEED_100;
	break;
	case MEDIA_TYPE_10M_FULL:
	mii_bmcr_data \|= BMCR_SPEED_10 \| BMCR_FULL_DUPLEX;
	break;
	case MEDIA_TYPE_10M_HALF:
	mii_bmcr_data \|= BMCR_SPEED_10;
	break;
	default:
	if (netif_msg_link(adapter))
	dev_err(&pdev->dev, "Wrong Media type %d\n",
	hw->media_type);
	return -1;
	break;
	}

	ret_val = atl1c_write_phy_reg(hw, MII_BMCR, mii_bmcr_data);
	if (ret_val)
	return ret_val;
	hw->phy_configured = true;

	return 0;
	}

	/*
	* Detects the current speed and duplex settings of the hardware.
	*
	* hw - Struct containing variables accessed by shared code
	* speed - Speed of the connection
	* duplex - Duplex setting of the connection
	*/
	int atl1c_get_speed_and_duplex(struct atl1c_hw hw, u16 speed, u16 *duplex)
	{
	int err;
	u16 phy_data;

	/* Read PHY Specific Status Register (17) */
	err = atl1c_read_phy_reg(hw, MII_GIGA_PSSR, &phy_data);
	if (err)
	return err;

	if (!(phy_data & GIGA_PSSR_SPD_DPLX_RESOLVED))
	return -1;

	switch (phy_data & GIGA_PSSR_SPEED) {
	case GIGA_PSSR_1000MBS:
	*speed = SPEED_1000;
	break;
	case GIGA_PSSR_100MBS:
	*speed = SPEED_100;
	break;
	case GIGA_PSSR_10MBS:
	*speed = SPEED_10;
	break;
	default:
	return -1;
	break;
	}

	if (phy_data & GIGA_PSSR_DPLX)
	*duplex = FULL_DUPLEX;
	else
	*duplex = HALF_DUPLEX;

	return 0;
	}

	int atl1c_restart_autoneg(struct atl1c_hw *hw)
	{
	int err = 0;
	u16 mii_bmcr_data = BMCR_RESET;

	err = atl1c_phy_setup_adv(hw);
	if (err)
	return err;
	mii_bmcr_data \|= BMCR_AUTO_NEG_EN \| BMCR_RESTART_AUTO_NEG;

	return atl1c_write_phy_reg(hw, MII_BMCR, mii_bmcr_data);
	}