/*
 * linux/arch/arm/mach-omap2/board-omap3beagle.c
 *
 * Copyright (C) 2008 Texas Instruments
 *
 * Modified from mach-omap2/board-3430sdp.c
 *
 * Initial code: Syed Mohammed Khasim
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/leds.h>
#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>

#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>

#include <linux/regulator/machine.h>
#include <linux/i2c/twl4030.h>

#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>

#include <mach/board.h>
#include <mach/common.h>
#include <mach/gpmc.h>
#include <mach/nand.h>
#include <mach/mux.h>
#include <mach/usb.h>
#include <mach/timer-gp.h>

#include "mmc-twl4030.h"

#define GPMC_CS0_BASE  0x60
#define GPMC_CS_SIZE   0x30

#define NAND_BLOCK_SIZE		SZ_128K

static struct mtd_partition omap3beagle_nand_partitions[] = {
	/* All the partition sizes are listed in terms of NAND block size */
	{
		.name		= "X-Loader",
		.offset		= 0,
		.size		= 4 * NAND_BLOCK_SIZE,
		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
	},
	{
		.name		= "U-Boot",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
		.size		= 15 * NAND_BLOCK_SIZE,
		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
	},
	{
		.name		= "U-Boot Env",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x260000 */
		.size		= 1 * NAND_BLOCK_SIZE,
	},
	{
		.name		= "Kernel",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
		.size		= 32 * NAND_BLOCK_SIZE,
	},
	{
		.name		= "File System",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x680000 */
		.size		= MTDPART_SIZ_FULL,
	},
};

static struct omap_nand_platform_data omap3beagle_nand_data = {
	.options	= NAND_BUSWIDTH_16,
	.parts		= omap3beagle_nand_partitions,
	.nr_parts	= ARRAY_SIZE(omap3beagle_nand_partitions),
	.dma_channel	= -1,		/* disable DMA in OMAP NAND driver */
	.nand_setup	= NULL,
	.dev_ready	= NULL,
};

static struct resource omap3beagle_nand_resource = {
	.flags		= IORESOURCE_MEM,
};

static struct platform_device omap3beagle_nand_device = {
	.name		= "omap2-nand",
	.id		= -1,
	.dev		= {
		.platform_data	= &omap3beagle_nand_data,
	},
	.num_resources	= 1,
	.resource	= &omap3beagle_nand_resource,
};

#include "sdram-micron-mt46h32m32lf-6.h"

static struct omap_uart_config omap3_beagle_uart_config __initdata = {
	.enabled_uarts	= ((1 << 0) | (1 << 1) | (1 << 2)),
};

static struct twl4030_hsmmc_info mmc[] = {
	{
		.mmc		= 1,
		.wires		= 8,
		.gpio_wp	= 29,
	},
	{}	/* Terminator */
};

static struct platform_device omap3_beagle_lcd_device = {
	.name		= "omap3beagle_lcd",
	.id		= -1,
};

static struct omap_lcd_config omap3_beagle_lcd_config __initdata = {
	.ctrl_name	= "internal",
};

static struct regulator_consumer_supply beagle_vmmc1_supply = {
	.supply			= "vmmc",
};

static struct regulator_consumer_supply beagle_vsim_supply = {
	.supply			= "vmmc_aux",
};

static struct gpio_led gpio_leds[];

static int beagle_twl_gpio_setup(struct device *dev,
		unsigned gpio, unsigned ngpio)
{
	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
	omap_cfg_reg(AH8_34XX_GPIO29);
	mmc[0].gpio_cd = gpio + 0;
	twl4030_mmc_init(mmc);

	/* link regulators to MMC adapters */
	beagle_vmmc1_supply.dev = mmc[0].dev;
	beagle_vsim_supply.dev = mmc[0].dev;

	/* REVISIT: need ehci-omap hooks for external VBUS
	 * power switch and overcurrent detect
	 */

	gpio_request(gpio + 1, "EHCI_nOC");
	gpio_direction_input(gpio + 1);

	/* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
	gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
	gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1);

	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;

	return 0;
}

static struct twl4030_gpio_platform_data beagle_gpio_data = {
	.gpio_base	= OMAP_MAX_GPIO_LINES,
	.irq_base	= TWL4030_GPIO_IRQ_BASE,
	.irq_end	= TWL4030_GPIO_IRQ_END,
	.use_leds	= true,
	.pullups	= BIT(1),
	.pulldowns	= BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
				| BIT(15) | BIT(16) | BIT(17),
	.setup		= beagle_twl_gpio_setup,
};

static struct regulator_consumer_supply beagle_vdac_supply = {
	.supply		= "vdac",
	.dev		= &omap3_beagle_lcd_device.dev,
};

static struct regulator_consumer_supply beagle_vdvi_supply = {
	.supply		= "vdvi",
	.dev		= &omap3_beagle_lcd_device.dev,
};

/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
static struct regulator_init_data beagle_vmmc1 = {
	.constraints = {
		.min_uV			= 1850000,
		.max_uV			= 3150000,
		.valid_modes_mask	= REGULATOR_MODE_NORMAL
					| REGULATOR_MODE_STANDBY,
		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
					| REGULATOR_CHANGE_MODE
					| REGULATOR_CHANGE_STATUS,
	},
	.num_consumer_supplies	= 1,
	.consumer_supplies	= &beagle_vmmc1_supply,
};

/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
static struct regulator_init_data beagle_vsim = {
	.constraints = {
		.min_uV			= 1800000,
		.max_uV			= 3000000,
		.valid_modes_mask	= REGULATOR_MODE_NORMAL
					| REGULATOR_MODE_STANDBY,
		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
					| REGULATOR_CHANGE_MODE
					| REGULATOR_CHANGE_STATUS,
	},
	.num_consumer_supplies	= 1,
	.consumer_supplies	= &beagle_vsim_supply,
};

/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
static struct regulator_init_data beagle_vdac = {
	.constraints = {
		.min_uV			= 1800000,
		.max_uV			= 1800000,
		.valid_modes_mask	= REGULATOR_MODE_NORMAL
					| REGULATOR_MODE_STANDBY,
		.valid_ops_mask		= REGULATOR_CHANGE_MODE
					| REGULATOR_CHANGE_STATUS,
	},
	.num_consumer_supplies	= 1,
	.consumer_supplies	= &beagle_vdac_supply,
};

/* VPLL2 for digital video outputs */
static struct regulator_init_data beagle_vpll2 = {
	.constraints = {
		.name			= "VDVI",
		.min_uV			= 1800000,
		.max_uV			= 1800000,
		.valid_modes_mask	= REGULATOR_MODE_NORMAL
					| REGULATOR_MODE_STANDBY,
		.valid_ops_mask		= REGULATOR_CHANGE_MODE
					| REGULATOR_CHANGE_STATUS,
	},
	.num_consumer_supplies	= 1,
	.consumer_supplies	= &beagle_vdvi_supply,
};

static struct twl4030_platform_data beagle_twldata = {
	.irq_base	= TWL4030_IRQ_BASE,
	.irq_end	= TWL4030_IRQ_END,

	/* platform_data for children goes here */
	.gpio		= &beagle_gpio_data,
	.vmmc1		= &beagle_vmmc1,
	.vsim		= &beagle_vsim,
	.vdac		= &beagle_vdac,
	.vpll2		= &beagle_vpll2,
};

static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
	{
		I2C_BOARD_INFO("twl4030", 0x48),
		.flags = I2C_CLIENT_WAKE,
		.irq = INT_34XX_SYS_NIRQ,
		.platform_data = &beagle_twldata,
	},
};

static int __init omap3_beagle_i2c_init(void)
{
	omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
			ARRAY_SIZE(beagle_i2c_boardinfo));
	/* Bus 3 is attached to the DVI port where devices like the pico DLP
	 * projector don't work reliably with 400kHz */
	omap_register_i2c_bus(3, 100, NULL, 0);
	return 0;
}

static void __init omap3_beagle_init_irq(void)
{
	omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
	omap_init_irq();
#ifdef CONFIG_OMAP_32K_TIMER
	omap2_gp_clockevent_set_gptimer(12);
#endif
	omap_gpio_init();
}

static struct gpio_led gpio_leds[] = {
	{
		.name			= "beagleboard::usr0",
		.default_trigger	= "heartbeat",
		.gpio			= 150,
	},
	{
		.name			= "beagleboard::usr1",
		.default_trigger	= "mmc0",
		.gpio			= 149,
	},
	{
		.name			= "beagleboard::pmu_stat",
		.gpio			= -EINVAL,	/* gets replaced */
		.active_low		= true,
	},
};

static struct gpio_led_platform_data gpio_led_info = {
	.leds		= gpio_leds,
	.num_leds	= ARRAY_SIZE(gpio_leds),
};

static struct platform_device leds_gpio = {
	.name	= "leds-gpio",
	.id	= -1,
	.dev	= {
		.platform_data	= &gpio_led_info,
	},
};

static struct gpio_keys_button gpio_buttons[] = {
	{
		.code			= BTN_EXTRA,
		.gpio			= 7,
		.desc			= "user",
		.wakeup			= 1,
	},
};

static struct gpio_keys_platform_data gpio_key_info = {
	.buttons	= gpio_buttons,
	.nbuttons	= ARRAY_SIZE(gpio_buttons),
};

static struct platform_device keys_gpio = {
	.name	= "gpio-keys",
	.id	= -1,
	.dev	= {
		.platform_data	= &gpio_key_info,
	},
};

static struct omap_board_config_kernel omap3_beagle_config[] __initdata = {
	{ OMAP_TAG_UART,	&omap3_beagle_uart_config },
	{ OMAP_TAG_LCD,		&omap3_beagle_lcd_config },
};

static struct platform_device *omap3_beagle_devices[] __initdata = {
	&omap3_beagle_lcd_device,
	&leds_gpio,
	&keys_gpio,
};

static void __init omap3beagle_flash_init(void)
{
	u8 cs = 0;
	u8 nandcs = GPMC_CS_NUM + 1;

	u32 gpmc_base_add = OMAP34XX_GPMC_VIRT;

	/* find out the chip-select on which NAND exists */
	while (cs < GPMC_CS_NUM) {
		u32 ret = 0;
		ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);

		if ((ret & 0xC00) == 0x800) {
			printk(KERN_INFO "Found NAND on CS%d\n", cs);
			if (nandcs > GPMC_CS_NUM)
				nandcs = cs;
		}
		cs++;
	}

	if (nandcs > GPMC_CS_NUM) {
		printk(KERN_INFO "NAND: Unable to find configuration "
				 "in GPMC\n ");
		return;
	}

	if (nandcs < GPMC_CS_NUM) {
		omap3beagle_nand_data.cs = nandcs;
		omap3beagle_nand_data.gpmc_cs_baseaddr = (void *)
			(gpmc_base_add + GPMC_CS0_BASE + nandcs * GPMC_CS_SIZE);
		omap3beagle_nand_data.gpmc_baseaddr = (void *) (gpmc_base_add);

		printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
		if (platform_device_register(&omap3beagle_nand_device) < 0)
			printk(KERN_ERR "Unable to register NAND device\n");
	}
}

static void __init omap3_beagle_init(void)
{
	omap3_beagle_i2c_init();
	platform_add_devices(omap3_beagle_devices,
			ARRAY_SIZE(omap3_beagle_devices));
	omap_board_config = omap3_beagle_config;
	omap_board_config_size = ARRAY_SIZE(omap3_beagle_config);
	omap_serial_init();

	omap_cfg_reg(J25_34XX_GPIO170);
	gpio_request(170, "DVI_nPD");
	/* REVISIT leave DVI powered down until it's needed ... */
	gpio_direction_output(170, true);

	usb_musb_init();
	omap3beagle_flash_init();
}

static void __init omap3_beagle_map_io(void)
{
	omap2_set_globals_343x();
	omap2_map_common_io();
}

MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
	/* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
	.phys_io	= 0x48000000,
	.io_pg_offst	= ((0xd8000000) >> 18) & 0xfffc,
	.boot_params	= 0x80000100,
	.map_io		= omap3_beagle_map_io,
	.init_irq	= omap3_beagle_init_irq,
	.init_machine	= omap3_beagle_init,
	.timer		= &omap_timer,
MACHINE_END
