arch/arm/kernel/head.S

/*
 *  linux/arch/arm/kernel/head.S
 *
 *  Copyright (C) 1994-2002 Russell King
 *  Copyright (c) 2003 ARM Limited
 *  All Rights Reserved
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 *  Kernel startup code for all 32-bit CPUs
 */
#include <linux/linkage.h>
#include <linux/init.h>

#include <asm/assembler.h>
#include <asm/domain.h>
#include <asm/ptrace.h>
#include <asm/asm-offsets.h>
#include <asm/memory.h>
#include <asm/thread_info.h>
#include <asm/system.h>

#ifdef CONFIG_DEBUG_LL
#include <mach/debug-macro.S>
#endif

/*
 * swapper_pg_dir is the virtual address of the initial page table.
 * We place the page tables 16K below KERNEL_RAM_VADDR.  Therefore, we must
 * make sure that KERNEL_RAM_VADDR is correctly set.  Currently, we expect
 * the least significant 16 bits to be 0x8000, but we could probably
 * relax this restriction to KERNEL_RAM_VADDR >= PAGE_OFFSET + 0x4000.
 */
#define KERNEL_RAM_VADDR	(PAGE_OFFSET + TEXT_OFFSET)
#if (KERNEL_RAM_VADDR & 0xffff) != 0x8000
#error KERNEL_RAM_VADDR must start at 0xXXXX8000
#endif

	.globl	swapper_pg_dir
	.equ	swapper_pg_dir, KERNEL_RAM_VADDR - 0x4000

	.macro	pgtbl, rd, phys
	add	\rd, \phys, #TEXT_OFFSET - 0x4000
	.endm

#ifdef CONFIG_XIP_KERNEL
#define KERNEL_START	XIP_VIRT_ADDR(CONFIG_XIP_PHYS_ADDR)
#define KERNEL_END	_edata_loc
#else
#define KERNEL_START	KERNEL_RAM_VADDR
#define KERNEL_END	_end
#endif

/*
 * Kernel startup entry point.
 * ---------------------------
 *
 * This is normally called from the decompressor code.  The requirements
 * are: MMU = off, D-cache = off, I-cache = dont care, r0 = 0,
 * r1 = machine nr, r2 = atags or dtb pointer.
 *
 * This code is mostly position independent, so if you link the kernel at
 * 0xc0008000, you call this at __pa(0xc0008000).
 *
 * See linux/arch/arm/tools/mach-types for the complete list of machine
 * numbers for r1.
 *
 * We're trying to keep crap to a minimum; DO NOT add any machine specific
 * crap here - that's what the boot loader (or in extreme, well justified
 * circumstances, zImage) is for.
 */
	.arm

	__HEAD
ENTRY(stext)

 THUMB(	adr	r9, BSYM(1f)	)	@ Kernel is always entered in ARM.
 THUMB(	bx	r9		)	@ If this is a Thumb-2 kernel,
 THUMB(	.thumb			)	@ switch to Thumb now.
 THUMB(1:			)

	setmode	PSR_F_BIT | PSR_I_BIT | SVC_MODE, r9 @ ensure svc mode
						@ and irqs disabled
	mrc	p15, 0, r9, c0, c0		@ get processor id
	bl	__lookup_processor_type		@ r5=procinfo r9=cpuid
	movs	r10, r5				@ invalid processor (r5=0)?
 THUMB( it	eq )		@ force fixup-able long branch encoding
	beq	__error_p			@ yes, error 'p'

#ifndef CONFIG_XIP_KERNEL
	adr	r3, 2f
	ldmia	r3, {r4, r8}
	sub	r4, r3, r4			@ (PHYS_OFFSET - PAGE_OFFSET)
	add	r8, r8, r4			@ PHYS_OFFSET
#else
	ldr	r8, =PHYS_OFFSET		@ always constant in this case
#endif

	/*
	 * r1 = machine no, r2 = atags or dtb,
	 * r8 = phys_offset, r9 = cpuid, r10 = procinfo
	 */
	bl	__vet_atags
#ifdef CONFIG_SMP_ON_UP
	bl	__fixup_smp
#endif
#ifdef CONFIG_ARM_PATCH_PHYS_VIRT
	bl	__fixup_pv_table
#endif
	bl	__create_page_tables

	/*
	 * The following calls CPU specific code in a position independent
	 * manner.  See arch/arm/mm/proc-*.S for details.  r10 = base of
	 * xxx_proc_info structure selected by __lookup_processor_type
	 * above.  On return, the CPU will be ready for the MMU to be
	 * turned on, and r0 will hold the CPU control register value.
	 */
	ldr	r13, =__mmap_switched		@ address to jump to after
						@ mmu has been enabled
	adr	lr, BSYM(1f)			@ return (PIC) address
	mov	r8, r4				@ set TTBR1 to swapper_pg_dir
 ARM(	add	pc, r10, #PROCINFO_INITFUNC	)
 THUMB(	add	r12, r10, #PROCINFO_INITFUNC	)
 THUMB(	mov	pc, r12				)
1:	b	__enable_mmu
ENDPROC(stext)
	.ltorg
#ifndef CONFIG_XIP_KERNEL
2:	.long	.
	.long	PAGE_OFFSET
#endif

/*
 * Setup the initial page tables.  We only setup the barest
 * amount which are required to get the kernel running, which
 * generally means mapping in the kernel code.
 *
 * r8 = phys_offset, r9 = cpuid, r10 = procinfo
 *
 * Returns:
 *  r0, r3, r5-r7 corrupted
 *  r4 = physical page table address
 */
__create_page_tables:
	pgtbl	r4, r8				@ page table address

	/*
	 * Clear the 16K level 1 swapper page table
	 */
	mov	r0, r4
	mov	r3, #0
	add	r6, r0, #0x4000
1:	str	r3, [r0], #4
	str	r3, [r0], #4
	str	r3, [r0], #4
	str	r3, [r0], #4
	teq	r0, r6
	bne	1b

	ldr	r7, [r10, #PROCINFO_MM_MMUFLAGS] @ mm_mmuflags

	/*
	 * Create identity mapping to cater for __enable_mmu.
	 * This identity mapping will be removed by paging_init().
	 */
	adr	r0, __enable_mmu_loc
	ldmia	r0, {r3, r5, r6}
	sub	r0, r0, r3			@ virt->phys offset
	add	r5, r5, r0			@ phys __enable_mmu
	add	r6, r6, r0			@ phys __enable_mmu_end
	mov	r5, r5, lsr #20
	mov	r6, r6, lsr #20

1:	orr	r3, r7, r5, lsl #20		@ flags + kernel base
	str	r3, [r4, r5, lsl #2]		@ identity mapping
	teq	r5, r6
	addne	r5, r5, #1			@ next section
	bne	1b

	/*
	 * Now setup the pagetables for our kernel direct
	 * mapped region.
	 */
	mov	r3, pc
	mov	r3, r3, lsr #20
	orr	r3, r7, r3, lsl #20
	add	r0, r4,  #(KERNEL_START & 0xff000000) >> 18
	str	r3, [r0, #(KERNEL_START & 0x00f00000) >> 18]!
	ldr	r6, =(KERNEL_END - 1)
	add	r0, r0, #4
	add	r6, r4, r6, lsr #18
1:	cmp	r0, r6
	add	r3, r3, #1 << 20
	strls	r3, [r0], #4
	bls	1b

#ifdef CONFIG_XIP_KERNEL
	/*
	 * Map some ram to cover our .data and .bss areas.
	 */
	add	r3, r8, #TEXT_OFFSET
	orr	r3, r3, r7
	add	r0, r4,  #(KERNEL_RAM_VADDR & 0xff000000) >> 18
	str	r3, [r0, #(KERNEL_RAM_VADDR & 0x00f00000) >> 18]!
	ldr	r6, =(_end - 1)
	add	r0, r0, #4
	add	r6, r4, r6, lsr #18
1:	cmp	r0, r6
	add	r3, r3, #1 << 20
	strls	r3, [r0], #4
	bls	1b
#endif

	/*
	 * Then map boot params address in r2 or
	 * the first 1MB of ram if boot params address is not specified.
	 */
	mov	r0, r2, lsr #20
	movs	r0, r0, lsl #20
	moveq	r0, r8
	sub	r3, r0, r8
	add	r3, r3, #PAGE_OFFSET
	add	r3, r4, r3, lsr #18
	orr	r6, r7, r0
	str	r6, [r3]

#ifdef CONFIG_DEBUG_LL
#ifndef CONFIG_DEBUG_ICEDCC
	/*
	 * Map in IO space for serial debugging.
	 * This allows debug messages to be output
	 * via a serial console before paging_init.
	 */
	addruart r7, r3, r0

	mov	r3, r3, lsr #20
	mov	r3, r3, lsl #2

	add	r0, r4, r3
	rsb	r3, r3, #0x4000			@ PTRS_PER_PGD*sizeof(long)
	cmp	r3, #0x0800			@ limit to 512MB
	movhi	r3, #0x0800
	add	r6, r0, r3
	mov	r3, r7, lsr #20
	ldr	r7, [r10, #PROCINFO_IO_MMUFLAGS] @ io_mmuflags
	orr	r3, r7, r3, lsl #20
1:	str	r3, [r0], #4
	add	r3, r3, #1 << 20
	teq	r0, r6
	bne	1b

#else /* CONFIG_DEBUG_ICEDCC */
	/* we don't need any serial debugging mappings for ICEDCC */
	ldr	r7, [r10, #PROCINFO_IO_MMUFLAGS] @ io_mmuflags
#endif /* !CONFIG_DEBUG_ICEDCC */

#if defined(CONFIG_ARCH_NETWINDER) || defined(CONFIG_ARCH_CATS)
	/*
	 * If we're using the NetWinder or CATS, we also need to map
	 * in the 16550-type serial port for the debug messages
	 */
	add	r0, r4, #0xff000000 >> 18
	orr	r3, r7, #0x7c000000
	str	r3, [r0]
#endif
#ifdef CONFIG_ARCH_RPC
	/*
	 * Map in screen at 0x02000000 & SCREEN2_BASE
	 * Similar reasons here - for debug.  This is
	 * only for Acorn RiscPC architectures.
	 */
	add	r0, r4, #0x02000000 >> 18
	orr	r3, r7, #0x02000000
	str	r3, [r0]
	add	r0, r4, #0xd8000000 >> 18
	str	r3, [r0]
#endif
#endif
	mov	pc, lr
ENDPROC(__create_page_tables)
	.ltorg
	.align
__enable_mmu_loc:
	.long	.
	.long	__enable_mmu
	.long	__enable_mmu_end

#if defined(CONFIG_SMP)
	__CPUINIT
ENTRY(secondary_startup)
	/*
	 * Common entry point for secondary CPUs.
	 *
	 * Ensure that we're in SVC mode, and IRQs are disabled.  Lookup
	 * the processor type - there is no need to check the machine type
	 * as it has already been validated by the primary processor.
	 */
	setmode	PSR_F_BIT | PSR_I_BIT | SVC_MODE, r9
	mrc	p15, 0, r9, c0, c0		@ get processor id
	bl	__lookup_processor_type
	movs	r10, r5				@ invalid processor?
	moveq	r0, #'p'			@ yes, error 'p'
 THUMB( it	eq )		@ force fixup-able long branch encoding
	beq	__error_p

	/*
	 * Use the page tables supplied from  __cpu_up.
	 */
	adr	r4, __secondary_data
	ldmia	r4, {r5, r7, r12}		@ address to jump to after
	sub	lr, r4, r5			@ mmu has been enabled
	ldr	r4, [r7, lr]			@ get secondary_data.pgdir
	add	r7, r7, #4
	ldr	r8, [r7, lr]			@ get secondary_data.swapper_pg_dir
	adr	lr, BSYM(__enable_mmu)		@ return address
	mov	r13, r12			@ __secondary_switched address
 ARM(	add	pc, r10, #PROCINFO_INITFUNC	) @ initialise processor
						  @ (return control reg)
 THUMB(	add	r12, r10, #PROCINFO_INITFUNC	)
 THUMB(	mov	pc, r12				)
ENDPROC(secondary_startup)

	/*
	 * r6  = &secondary_data
	 */
ENTRY(__secondary_switched)
	ldr	sp, [r7, #4]			@ get secondary_data.stack
	mov	fp, #0
	b	secondary_start_kernel
ENDPROC(__secondary_switched)

	.align

	.type	__secondary_data, %object
__secondary_data:
	.long	.
	.long	secondary_data
	.long	__secondary_switched
#endif /* defined(CONFIG_SMP) */



/*
 * Setup common bits before finally enabling the MMU.  Essentially
 * this is just loading the page table pointer and domain access
 * registers.
 *
 *  r0  = cp#15 control register
 *  r1  = machine ID
 *  r2  = atags or dtb pointer
 *  r4  = page table pointer
 *  r9  = processor ID
 *  r13 = *virtual* address to jump to upon completion
 */
__enable_mmu:
#ifdef CONFIG_ALIGNMENT_TRAP
	orr	r0, r0, #CR_A
#else
	bic	r0, r0, #CR_A
#endif
#ifdef CONFIG_CPU_DCACHE_DISABLE
	bic	r0, r0, #CR_C
#endif
#ifdef CONFIG_CPU_BPREDICT_DISABLE
	bic	r0, r0, #CR_Z
#endif
#ifdef CONFIG_CPU_ICACHE_DISABLE
	bic	r0, r0, #CR_I
#endif
	mov	r5, #(domain_val(DOMAIN_USER, DOMAIN_MANAGER) | \
		      domain_val(DOMAIN_KERNEL, DOMAIN_MANAGER) | \
		      domain_val(DOMAIN_TABLE, DOMAIN_MANAGER) | \
		      domain_val(DOMAIN_IO, DOMAIN_CLIENT))
	mcr	p15, 0, r5, c3, c0, 0		@ load domain access register
	mcr	p15, 0, r4, c2, c0, 0		@ load page table pointer
	b	__turn_mmu_on
ENDPROC(__enable_mmu)

/*
 * Enable the MMU.  This completely changes the structure of the visible
 * memory space.  You will not be able to trace execution through this.
 * If you have an enquiry about this, *please* check the linux-arm-kernel
 * mailing list archives BEFORE sending another post to the list.
 *
 *  r0  = cp#15 control register
 *  r1  = machine ID
 *  r2  = atags or dtb pointer
 *  r9  = processor ID
 *  r13 = *virtual* address to jump to upon completion
 *
 * other registers depend on the function called upon completion
 */
	.align	5
__turn_mmu_on:
	mov	r0, r0
	mcr	p15, 0, r0, c1, c0, 0		@ write control reg
	mrc	p15, 0, r3, c0, c0, 0		@ read id reg
	mov	r3, r3
	mov	r3, r13
	mov	pc, r3
__enable_mmu_end:
ENDPROC(__turn_mmu_on)


#ifdef CONFIG_SMP_ON_UP
	__INIT
__fixup_smp:
	and	r3, r9, #0x000f0000	@ architecture version
	teq	r3, #0x000f0000		@ CPU ID supported?
	bne	__fixup_smp_on_up	@ no, assume UP

	bic	r3, r9, #0x00ff0000
	bic	r3, r3, #0x0000000f	@ mask 0xff00fff0
	mov	r4, #0x41000000
	orr	r4, r4, #0x0000b000
	orr	r4, r4, #0x00000020	@ val 0x4100b020
	teq	r3, r4			@ ARM 11MPCore?
	moveq	pc, lr			@ yes, assume SMP

	mrc	p15, 0, r0, c0, c0, 5	@ read MPIDR
	and	r0, r0, #0xc0000000	@ multiprocessing extensions and
	teq	r0, #0x80000000		@ not part of a uniprocessor system?
	moveq	pc, lr			@ yes, assume SMP

__fixup_smp_on_up:
	adr	r0, 1f
	ldmia	r0, {r3 - r5}
	sub	r3, r0, r3
	add	r4, r4, r3
	add	r5, r5, r3
	b	__do_fixup_smp_on_up
ENDPROC(__fixup_smp)

	.align
1:	.word	.
	.word	__smpalt_begin
	.word	__smpalt_end

	.pushsection .data
	.globl	smp_on_up
smp_on_up:
	ALT_SMP(.long	1)
	ALT_UP(.long	0)
	.popsection
#endif

	.text
__do_fixup_smp_on_up:
	cmp	r4, r5
	movhs	pc, lr
	ldmia	r4!, {r0, r6}
 ARM(	str	r6, [r0, r3]	)
 THUMB(	add	r0, r0, r3	)
#ifdef __ARMEB__
 THUMB(	mov	r6, r6, ror #16	)	@ Convert word order for big-endian.
#endif
 THUMB(	strh	r6, [r0], #2	)	@ For Thumb-2, store as two halfwords
 THUMB(	mov	r6, r6, lsr #16	)	@ to be robust against misaligned r3.
 THUMB(	strh	r6, [r0]	)
	b	__do_fixup_smp_on_up
ENDPROC(__do_fixup_smp_on_up)

ENTRY(fixup_smp)
	stmfd	sp!, {r4 - r6, lr}
	mov	r4, r0
	add	r5, r0, r1
	mov	r3, #0
	bl	__do_fixup_smp_on_up
	ldmfd	sp!, {r4 - r6, pc}
ENDPROC(fixup_smp)

#ifdef CONFIG_ARM_PATCH_PHYS_VIRT

/* __fixup_pv_table - patch the stub instructions with the delta between
 * PHYS_OFFSET and PAGE_OFFSET, which is assumed to be 16MiB aligned and
 * can be expressed by an immediate shifter operand. The stub instruction
 * has a form of '(add|sub) rd, rn, #imm'.
 */
	__HEAD
__fixup_pv_table:
	adr	r0, 1f
	ldmia	r0, {r3-r5, r7}
	sub	r3, r0, r3	@ PHYS_OFFSET - PAGE_OFFSET
	add	r4, r4, r3	@ adjust table start address
	add	r5, r5, r3	@ adjust table end address
	add	r7, r7, r3	@ adjust __pv_phys_offset address
	str	r8, [r7]	@ save computed PHYS_OFFSET to __pv_phys_offset
	mov	r6, r3, lsr #24	@ constant for add/sub instructions
	teq	r3, r6, lsl #24 @ must be 16MiB aligned
THUMB(	it	ne		@ cross section branch )
	bne	__error
	str	r6, [r7, #4]	@ save to __pv_offset
	b	__fixup_a_pv_table
ENDPROC(__fixup_pv_table)

	.align
1:	.long	.
	.long	__pv_table_begin
	.long	__pv_table_end
2:	.long	__pv_phys_offset

	.text
__fixup_a_pv_table:
#ifdef CONFIG_THUMB2_KERNEL
	lsls	r6, #24
	beq	2f
	clz	r7, r6
	lsr	r6, #24
	lsl	r6, r7
	bic	r6, #0x0080
	lsrs	r7, #1
	orrcs	r6, #0x0080
	orr	r6, r6, r7, lsl #12
	orr	r6, #0x4000
	b	2f
1:	add     r7, r3
	ldrh	ip, [r7, #2]
	and	ip, 0x8f00
	orr	ip, r6	@ mask in offset bits 31-24
	strh	ip, [r7, #2]
2:	cmp	r4, r5
	ldrcc	r7, [r4], #4	@ use branch for delay slot
	bcc	1b
	bx	lr
#else
	b	2f
1:	ldr	ip, [r7, r3]
	bic	ip, ip, #0x000000ff
	orr	ip, ip, r6	@ mask in offset bits 31-24
	str	ip, [r7, r3]
2:	cmp	r4, r5
	ldrcc	r7, [r4], #4	@ use branch for delay slot
	bcc	1b
	mov	pc, lr
#endif
ENDPROC(__fixup_a_pv_table)

ENTRY(fixup_pv_table)
	stmfd	sp!, {r4 - r7, lr}
	ldr	r2, 2f			@ get address of __pv_phys_offset
	mov	r3, #0			@ no offset
	mov	r4, r0			@ r0 = table start
	add	r5, r0, r1		@ r1 = table size
	ldr	r6, [r2, #4]		@ get __pv_offset
	bl	__fixup_a_pv_table
	ldmfd	sp!, {r4 - r7, pc}
ENDPROC(fixup_pv_table)

	.align
2:	.long	__pv_phys_offset

	.data
	.globl	__pv_phys_offset
	.type	__pv_phys_offset, %object
__pv_phys_offset:
	.long	0
	.size	__pv_phys_offset, . - __pv_phys_offset
__pv_offset:
	.long	0
#endif

#include "head-common.S"