| Guenter Roeck | 920fa1f | 2010-08-09 17:21:06 -0700 | [diff] [blame] | 1 | Kernel driver smm665 |
| 2 | ==================== |
| 3 | |
| 4 | Supported chips: |
| 5 | * Summit Microelectronics SMM465 |
| 6 | Prefix: 'smm465' |
| 7 | Addresses scanned: - |
| 8 | Datasheet: |
| 9 | http://www.summitmicro.com/prod_select/summary/SMM465/SMM465DS.pdf |
| 10 | * Summit Microelectronics SMM665, SMM665B |
| 11 | Prefix: 'smm665' |
| 12 | Addresses scanned: - |
| 13 | Datasheet: |
| 14 | http://www.summitmicro.com/prod_select/summary/SMM665/SMM665B_2089_20.pdf |
| 15 | * Summit Microelectronics SMM665C |
| 16 | Prefix: 'smm665c' |
| 17 | Addresses scanned: - |
| 18 | Datasheet: |
| 19 | http://www.summitmicro.com/prod_select/summary/SMM665C/SMM665C_2125.pdf |
| 20 | * Summit Microelectronics SMM764 |
| 21 | Prefix: 'smm764' |
| 22 | Addresses scanned: - |
| 23 | Datasheet: |
| 24 | http://www.summitmicro.com/prod_select/summary/SMM764/SMM764_2098.pdf |
| 25 | * Summit Microelectronics SMM766, SMM766B |
| 26 | Prefix: 'smm766' |
| 27 | Addresses scanned: - |
| 28 | Datasheets: |
| 29 | http://www.summitmicro.com/prod_select/summary/SMM766/SMM766_2086.pdf |
| 30 | http://www.summitmicro.com/prod_select/summary/SMM766B/SMM766B_2122.pdf |
| 31 | |
| 32 | Author: Guenter Roeck <guenter.roeck@ericsson.com> |
| 33 | |
| 34 | |
| 35 | Module Parameters |
| 36 | ----------------- |
| 37 | |
| 38 | * vref: int |
| 39 | Default: 1250 (mV) |
| 40 | Reference voltage on VREF_ADC pin in mV. It should not be necessary to set |
| 41 | this parameter unless a non-default reference voltage is used. |
| 42 | |
| 43 | |
| 44 | Description |
| 45 | ----------- |
| 46 | |
| 47 | [From datasheet] The SMM665 is an Active DC Output power supply Controller |
| 48 | that monitors, margins and cascade sequences power. The part monitors six |
| 49 | power supply channels as well as VDD, 12V input, two general-purpose analog |
| 50 | inputs and an internal temperature sensor using a 10-bit ADC. |
| 51 | |
| 52 | Each monitored channel has its own high and low limits, plus a critical |
| 53 | limit. |
| 54 | |
| 55 | Support for SMM465, SMM764, and SMM766 has been implemented but is untested. |
| 56 | |
| 57 | |
| 58 | Usage Notes |
| 59 | ----------- |
| 60 | |
| 61 | This driver does not probe for devices, since there is no register which |
| 62 | can be safely used to identify the chip. You will have to instantiate |
| 63 | the devices explicitly. When instantiating the device, you have to specify |
| 64 | its configuration register address. |
| 65 | |
| 66 | Example: the following will load the driver for an SMM665 at address 0x57 |
| 67 | on I2C bus #1: |
| 68 | $ modprobe smm665 |
| 69 | $ echo smm665 0x57 > /sys/bus/i2c/devices/i2c-1/new_device |
| 70 | |
| 71 | |
| 72 | Sysfs entries |
| 73 | ------------- |
| 74 | |
| 75 | This driver uses the values in the datasheet to convert ADC register values |
| 76 | into the values specified in the sysfs-interface document. All attributes are |
| 77 | read only. |
| 78 | |
| 79 | Min, max, lcrit, and crit values are used by the chip to trigger external signals |
| 80 | and/or other activity. Triggered signals can include HEALTHY, RST, Power Off, |
| 81 | or Fault depending on the chip configuration. The driver reports values as lcrit |
| 82 | or crit if exceeding the limits triggers RST, Power Off, or Fault, and as min or |
| 83 | max otherwise. For details please see the SMM665 datasheet. |
| 84 | |
| 85 | For SMM465 and SMM764, values for Channel E and F are reported but undefined. |
| 86 | |
| 87 | in1_input 12V input voltage (mV) |
| 88 | in2_input 3.3V (VDD) input voltage (mV) |
| 89 | in3_input Channel A voltage (mV) |
| 90 | in4_input Channel B voltage (mV) |
| 91 | in5_input Channel C voltage (mV) |
| 92 | in6_input Channel D voltage (mV) |
| 93 | in7_input Channel E voltage (mV) |
| 94 | in8_input Channel F voltage (mV) |
| 95 | in9_input AIN1 voltage (mV) |
| 96 | in10_input AIN2 voltage (mV) |
| 97 | |
| 98 | in1_min 12v input minimum voltage (mV) |
| 99 | in2_min 3.3V (VDD) input minimum voltage (mV) |
| 100 | in3_min Channel A minimum voltage (mV) |
| 101 | in4_min Channel B minimum voltage (mV) |
| 102 | in5_min Channel C minimum voltage (mV) |
| 103 | in6_min Channel D minimum voltage (mV) |
| 104 | in7_min Channel E minimum voltage (mV) |
| 105 | in8_min Channel F minimum voltage (mV) |
| 106 | in9_min AIN1 minimum voltage (mV) |
| 107 | in10_min AIN2 minimum voltage (mV) |
| 108 | |
| 109 | in1_max 12v input maximum voltage (mV) |
| 110 | in2_max 3.3V (VDD) input maximum voltage (mV) |
| 111 | in3_max Channel A maximum voltage (mV) |
| 112 | in4_max Channel B maximum voltage (mV) |
| 113 | in5_max Channel C maximum voltage (mV) |
| 114 | in6_max Channel D maximum voltage (mV) |
| 115 | in7_max Channel E maximum voltage (mV) |
| 116 | in8_max Channel F maximum voltage (mV) |
| 117 | in9_max AIN1 maximum voltage (mV) |
| 118 | in10_max AIN2 maximum voltage (mV) |
| 119 | |
| 120 | in1_lcrit 12v input critical minimum voltage (mV) |
| 121 | in2_lcrit 3.3V (VDD) input critical minimum voltage (mV) |
| 122 | in3_lcrit Channel A critical minimum voltage (mV) |
| 123 | in4_lcrit Channel B critical minimum voltage (mV) |
| 124 | in5_lcrit Channel C critical minimum voltage (mV) |
| 125 | in6_lcrit Channel D critical minimum voltage (mV) |
| 126 | in7_lcrit Channel E critical minimum voltage (mV) |
| 127 | in8_lcrit Channel F critical minimum voltage (mV) |
| 128 | in9_lcrit AIN1 critical minimum voltage (mV) |
| 129 | in10_lcrit AIN2 critical minimum voltage (mV) |
| 130 | |
| 131 | in1_crit 12v input critical maximum voltage (mV) |
| 132 | in2_crit 3.3V (VDD) input critical maximum voltage (mV) |
| 133 | in3_crit Channel A critical maximum voltage (mV) |
| 134 | in4_crit Channel B critical maximum voltage (mV) |
| 135 | in5_crit Channel C critical maximum voltage (mV) |
| 136 | in6_crit Channel D critical maximum voltage (mV) |
| 137 | in7_crit Channel E critical maximum voltage (mV) |
| 138 | in8_crit Channel F critical maximum voltage (mV) |
| 139 | in9_crit AIN1 critical maximum voltage (mV) |
| 140 | in10_crit AIN2 critical maximum voltage (mV) |
| 141 | |
| 142 | in1_crit_alarm 12v input critical alarm |
| 143 | in2_crit_alarm 3.3V (VDD) input critical alarm |
| 144 | in3_crit_alarm Channel A critical alarm |
| 145 | in4_crit_alarm Channel B critical alarm |
| 146 | in5_crit_alarm Channel C critical alarm |
| 147 | in6_crit_alarm Channel D critical alarm |
| 148 | in7_crit_alarm Channel E critical alarm |
| 149 | in8_crit_alarm Channel F critical alarm |
| 150 | in9_crit_alarm AIN1 critical alarm |
| 151 | in10_crit_alarm AIN2 critical alarm |
| 152 | |
| Guenter Roeck | c1a76b4 | 2011-04-18 09:43:22 -0700 | [diff] [blame] | 153 | temp1_input Chip temperature |
| 154 | temp1_min Mimimum chip temperature |
| 155 | temp1_max Maximum chip temperature |
| 156 | temp1_crit Critical chip temperature |
| Guenter Roeck | 920fa1f | 2010-08-09 17:21:06 -0700 | [diff] [blame] | 157 | temp1_crit_alarm Temperature critical alarm |