| Jaya Kumar | 90b8fc3 | 2008-03-15 05:11:07 +0100 | [diff] [blame] | 1 | /* |
| 2 | * linux/include/asm-arm/arch-pxa/gumstix.h |
| 3 | * |
| 4 | * This program is free software; you can redistribute it and/or modify |
| 5 | * it under the terms of the GNU General Public License version 2 as |
| 6 | * published by the Free Software Foundation. |
| 7 | */ |
| 8 | |
| 9 | |
| 10 | /* BTRESET - Reset line to Bluetooth module, active low signal. */ |
| 11 | #define GPIO_GUMSTIX_BTRESET 7 |
| 12 | #define GPIO_GUMSTIX_BTRESET_MD (GPIO_GUMSTIX_BTRESET | GPIO_OUT) |
| 13 | |
| 14 | |
| 15 | /* |
| 16 | GPIOn - Input from MAX823 (or equiv), normalizing USB +5V into a clean |
| 17 | interrupt signal for determining cable presence. On the original gumstix, |
| 18 | this is GPIO81, and GPIO83 needs to be defined as well. On the gumstix F, |
| 19 | this moves to GPIO17 and GPIO37. */ |
| 20 | |
| 21 | /* GPIOx - Connects to USB D+ and used as a pull-up after GPIOn |
| 22 | has detected a cable insertion; driven low otherwise. */ |
| 23 | |
| 24 | #ifdef CONFIG_ARCH_GUMSTIX_ORIG |
| 25 | |
| 26 | #define GPIO_GUMSTIX_USB_GPIOn 81 |
| 27 | #define GPIO_GUMSTIX_USB_GPIOx 83 |
| 28 | |
| 29 | #else |
| 30 | |
| 31 | #define GPIO_GUMSTIX_USB_GPIOn 35 |
| 32 | #define GPIO_GUMSTIX_USB_GPIOx 41 |
| 33 | |
| 34 | #endif |
| 35 | |
| 36 | /* usb state change */ |
| 37 | #define GUMSTIX_USB_INTR_IRQ IRQ_GPIO(GPIO_GUMSTIX_USB_GPIOn) |
| 38 | |
| 39 | #define GPIO_GUMSTIX_USB_GPIOn_MD (GPIO_GUMSTIX_USB_GPIOn | GPIO_IN) |
| 40 | #define GPIO_GUMSTIX_USB_GPIOx_CON_MD (GPIO_GUMSTIX_USB_GPIOx | GPIO_OUT) |
| 41 | #define GPIO_GUMSTIX_USB_GPIOx_DIS_MD (GPIO_GUMSTIX_USB_GPIOx | GPIO_IN) |
| 42 | |
| 43 | /* |
| 44 | * SD/MMC definitions |
| 45 | */ |
| 46 | #define GUMSTIX_GPIO_nSD_WP 22 /* SD Write Protect */ |
| 47 | #define GUMSTIX_GPIO_nSD_DETECT 11 /* MMC/SD Card Detect */ |
| 48 | #define GUMSTIX_IRQ_GPIO_nSD_DETECT IRQ_GPIO(GUMSTIX_GPIO_nSD_DETECT) |
| 49 | |
| 50 | /* |
| 51 | * SMC Ethernet definitions |
| 52 | * ETH_RST provides a hardware reset line to the ethernet chip |
| 53 | * ETH is the IRQ line in from the ethernet chip to the PXA |
| 54 | */ |
| 55 | #define GPIO_GUMSTIX_ETH0_RST 80 |
| 56 | #define GPIO_GUMSTIX_ETH0_RST_MD (GPIO_GUMSTIX_ETH0_RST | GPIO_OUT) |
| 57 | #define GPIO_GUMSTIX_ETH1_RST 52 |
| 58 | #define GPIO_GUMSTIX_ETH1_RST_MD (GPIO_GUMSTIX_ETH1_RST | GPIO_OUT) |
| 59 | |
| 60 | #define GPIO_GUMSTIX_ETH0 36 |
| 61 | #define GPIO_GUMSTIX_ETH0_MD (GPIO_GUMSTIX_ETH0 | GPIO_IN) |
| 62 | #define GUMSTIX_ETH0_IRQ IRQ_GPIO(GPIO_GUMSTIX_ETH0) |
| 63 | #define GPIO_GUMSTIX_ETH1 27 |
| 64 | #define GPIO_GUMSTIX_ETH1_MD (GPIO_GUMSTIX_ETH1 | GPIO_IN) |
| 65 | #define GUMSTIX_ETH1_IRQ IRQ_GPIO(GPIO_GUMSTIX_ETH1) |
| 66 | |
| 67 | |
| 68 | /* CF reset line */ |
| 69 | #define GPIO8_RESET 8 |
| 70 | |
| 71 | /* CF slot 0 */ |
| 72 | #define GPIO4_nBVD1 4 |
| 73 | #define GPIO4_nSTSCHG GPIO4_nBVD1 |
| 74 | #define GPIO11_nCD 11 |
| 75 | #define GPIO26_PRDY_nBSY 26 |
| 76 | #define GUMSTIX_S0_nSTSCHG_IRQ IRQ_GPIO(GPIO4_nSTSCHG) |
| 77 | #define GUMSTIX_S0_nCD_IRQ IRQ_GPIO(GPIO11_nCD) |
| 78 | #define GUMSTIX_S0_PRDY_nBSY_IRQ IRQ_GPIO(GPIO26_PRDY_nBSY) |
| 79 | |
| 80 | /* CF slot 1 */ |
| 81 | #define GPIO18_nBVD1 18 |
| 82 | #define GPIO18_nSTSCHG GPIO18_nBVD1 |
| 83 | #define GPIO36_nCD 36 |
| 84 | #define GPIO27_PRDY_nBSY 27 |
| 85 | #define GUMSTIX_S1_nSTSCHG_IRQ IRQ_GPIO(GPIO18_nSTSCHG) |
| 86 | #define GUMSTIX_S1_nCD_IRQ IRQ_GPIO(GPIO36_nCD) |
| 87 | #define GUMSTIX_S1_PRDY_nBSY_IRQ IRQ_GPIO(GPIO27_PRDY_nBSY) |
| 88 | |
| 89 | /* CF GPIO line modes */ |
| 90 | #define GPIO4_nSTSCHG_MD (GPIO4_nSTSCHG | GPIO_IN) |
| 91 | #define GPIO8_RESET_MD (GPIO8_RESET | GPIO_OUT) |
| 92 | #define GPIO11_nCD_MD (GPIO11_nCD | GPIO_IN) |
| 93 | #define GPIO18_nSTSCHG_MD (GPIO18_nSTSCHG | GPIO_IN) |
| 94 | #define GPIO26_PRDY_nBSY_MD (GPIO26_PRDY_nBSY | GPIO_IN) |
| 95 | #define GPIO27_PRDY_nBSY_MD (GPIO27_PRDY_nBSY | GPIO_IN) |
| 96 | #define GPIO36_nCD_MD (GPIO36_nCD | GPIO_IN) |