)]}'
{
  "log": [
    {
      "commit": "24cd73a3942f3df214d7953f0cfd65d5085fa583",
      "tree": "ead53b3f9d40915b629fdcef2e2af89c21c66b0b",
      "parents": [
        "44051996230510ccb125cfa552d464950d1767b9"
      ],
      "author": {
        "name": "Richard Röjfors",
        "email": "richard.rojfors@pelagicore.com",
        "time": "Tue Apr 27 14:16:34 2010 -0700"
      },
      "committer": {
        "name": "Greg Kroah-Hartman",
        "email": "gregkh@suse.de",
        "time": "Fri May 21 09:34:29 2010 -0700"
      },
      "message": "serial: timbuart: make sure last byte is sent when port is closed\n\nFix a problem in early versions of the FPGA IP.\n\nIn certain situations the IP reports that the FIFO is empty, but a byte is\nstill clocked out.  If a flush is done at that point the currently clocked\nbyte is canceled.\n\nThis causes incompatibilities with the upper layers when a port is closed,\nit waits until the FIFO is empty and then closes the port.  During close\nthe FIFO is flushed -\u003e the last byte is not sent properly.\n\nNow the FIFO is only flushed if it is reported to be non-empty.  Which\nmakes the currently clocked out byte to finish.\n\n[akpm@linux-foundation.org: fix build]\nSigned-off-by: Richard Röjfors \u003crichard.rojfors@pelagicore.com\u003e\nSigned-off-by: Andrew Morton \u003cakpm@linux-foundation.org\u003e\nSigned-off-by: Greg Kroah-Hartman \u003cgregkh@suse.de\u003e\n\n"
    },
    {
      "commit": "44051996230510ccb125cfa552d464950d1767b9",
      "tree": "f014bf034466fafa6d53cea65cc477642939967d",
      "parents": [
        "e5bbbb18d872cb4e29815a000485c2c5eebcfaca"
      ],
      "author": {
        "name": "Roel Kluin",
        "email": "roel.kluin@gmail.com",
        "time": "Tue Apr 27 14:16:33 2010 -0700"
      },
      "committer": {
        "name": "Greg Kroah-Hartman",
        "email": "gregkh@suse.de",
        "time": "Fri May 21 09:34:29 2010 -0700"
      },
      "message": "serial: two branches the same in timbuart_set_mctrl()\n\nCTS is a read only bit and we are to stop signal RTS if modem line\nTIOCM_RTS is not set.\n\nThanks for suggestions by Richard Röjfors.\n\nSigned-off-by: Roel Kluin \u003croel.kluin@gmail.com\u003e\nAcked-by: Richard Röjfors \u003crichard.rojfors@pelagicore.com\u003e\nCc: Alan Cox \u003calan@lxorguk.ukuu.org.uk\u003e\nSigned-off-by: Andrew Morton \u003cakpm@linux-foundation.org\u003e\nSigned-off-by: Greg Kroah-Hartman \u003cgregkh@suse.de\u003e\n\n"
    },
    {
      "commit": "5a0e3ad6af8660be21ca98a971cd00f331318c05",
      "tree": "5bfb7be11a03176a87296a43ac6647975c00a1d1",
      "parents": [
        "ed391f4ebf8f701d3566423ce8f17e614cde9806"
      ],
      "author": {
        "name": "Tejun Heo",
        "email": "tj@kernel.org",
        "time": "Wed Mar 24 17:04:11 2010 +0900"
      },
      "committer": {
        "name": "Tejun Heo",
        "email": "tj@kernel.org",
        "time": "Tue Mar 30 22:02:32 2010 +0900"
      },
      "message": "include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h\n\npercpu.h is included by sched.h and module.h and thus ends up being\nincluded when building most .c files.  percpu.h includes slab.h which\nin turn includes gfp.h making everything defined by the two files\nuniversally available and complicating inclusion dependencies.\n\npercpu.h -\u003e slab.h dependency is about to be removed.  Prepare for\nthis change by updating users of gfp and slab facilities include those\nheaders directly instead of assuming availability.  As this conversion\nneeds to touch large number of source files, the following script is\nused as the basis of conversion.\n\n  http://userweb.kernel.org/~tj/misc/slabh-sweep.py\n\nThe script does the followings.\n\n* Scan files for gfp and slab usages and update includes such that\n  only the necessary includes are there.  ie. if only gfp is used,\n  gfp.h, if slab is used, slab.h.\n\n* When the script inserts a new include, it looks at the include\n  blocks and try to put the new include such that its order conforms\n  to its surrounding.  It\u0027s put in the include block which contains\n  core kernel includes, in the same order that the rest are ordered -\n  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there\n  doesn\u0027t seem to be any matching order.\n\n* If the script can\u0027t find a place to put a new include (mostly\n  because the file doesn\u0027t have fitting include block), it prints out\n  an error message indicating which .h file needs to be added to the\n  file.\n\nThe conversion was done in the following steps.\n\n1. The initial automatic conversion of all .c files updated slightly\n   over 4000 files, deleting around 700 includes and adding ~480 gfp.h\n   and ~3000 slab.h inclusions.  The script emitted errors for ~400\n   files.\n\n2. Each error was manually checked.  Some didn\u0027t need the inclusion,\n   some needed manual addition while adding it to implementation .h or\n   embedding .c file was more appropriate for others.  This step added\n   inclusions to around 150 files.\n\n3. The script was run again and the output was compared to the edits\n   from #2 to make sure no file was left behind.\n\n4. Several build tests were done and a couple of problems were fixed.\n   e.g. lib/decompress_*.c used malloc/free() wrappers around slab\n   APIs requiring slab.h to be added manually.\n\n5. The script was run on all .h files but without automatically\n   editing them as sprinkling gfp.h and slab.h inclusions around .h\n   files could easily lead to inclusion dependency hell.  Most gfp.h\n   inclusion directives were ignored as stuff from gfp.h was usually\n   wildly available and often used in preprocessor macros.  Each\n   slab.h inclusion directive was examined and added manually as\n   necessary.\n\n6. percpu.h was updated not to include slab.h.\n\n7. Build test were done on the following configurations and failures\n   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my\n   distributed build env didn\u0027t work with gcov compiles) and a few\n   more options had to be turned off depending on archs to make things\n   build (like ipr on powerpc/64 which failed due to missing writeq).\n\n   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.\n   * powerpc and powerpc64 SMP allmodconfig\n   * sparc and sparc64 SMP allmodconfig\n   * ia64 SMP allmodconfig\n   * s390 SMP allmodconfig\n   * alpha SMP allmodconfig\n   * um on x86_64 SMP allmodconfig\n\n8. percpu.h modifications were reverted so that it could be applied as\n   a separate patch and serve as bisection point.\n\nGiven the fact that I had only a couple of failures from tests on step\n6, I\u0027m fairly confident about the coverage of this conversion patch.\nIf there is a breakage, it\u0027s likely to be something in one of the arch\nheaders which should be easily discoverable easily on most builds of\nthe specific arch.\n\nSigned-off-by: Tejun Heo \u003ctj@kernel.org\u003e\nGuess-its-ok-by: Christoph Lameter \u003ccl@linux-foundation.org\u003e\nCc: Ingo Molnar \u003cmingo@redhat.com\u003e\nCc: Lee Schermerhorn \u003cLee.Schermerhorn@hp.com\u003e\n"
    },
    {
      "commit": "1e091751cdb2c28f9f25041be0dcb4d33e4a833d",
      "tree": "364819510f0ef782277437d0c98170b46bcde35e",
      "parents": [
        "2a52fcb54fdf4b557730022aefcc794d567591fb"
      ],
      "author": {
        "name": "Roel Kluin",
        "email": "roel.kluin@gmail.com",
        "time": "Mon Dec 21 16:26:49 2009 -0800"
      },
      "committer": {
        "name": "Greg Kroah-Hartman",
        "email": "gregkh@suse.de",
        "time": "Tue Mar 02 14:43:11 2010 -0800"
      },
      "message": "serial: fix test of unsigned\n\nThe variables were unsigned so the tests did not work.\n\nSigned-off-by: Roel Kluin \u003croel.kluin@gmail.com\u003e\nCc: Alan Cox \u003calan@lxorguk.ukuu.org.uk\u003e\nSigned-off-by: Andrew Morton \u003cakpm@linux-foundation.org\u003e\nSigned-off-by: Greg Kroah-Hartman \u003cgregkh@suse.de\u003e\n\n"
    },
    {
      "commit": "bdc04e3174e18f475289fa8f4144f66686326b7e",
      "tree": "c0bf03c8d6df1629bfa26b686fe65ffb0c87aeb7",
      "parents": [
        "a2bceae065ed8c4f552b35c4dde4cc2db05ce9e3"
      ],
      "author": {
        "name": "Alan Cox",
        "email": "alan@linux.intel.com",
        "time": "Sat Sep 19 13:13:31 2009 -0700"
      },
      "committer": {
        "name": "Live-CD User",
        "email": "linux@linux.site",
        "time": "Sat Sep 19 13:13:31 2009 -0700"
      },
      "message": "serial: move delta_msr_wait into the tty_port\n\nThis is used by various drivers not just serial and can be extracted\nas commonality\n\nSigned-off-by: Alan Cox \u003calan@linux.intel.com\u003e\n"
    },
    {
      "commit": "ebd2c8f6d2ec4012c267ecb95e72a57b8355a705",
      "tree": "36a01b2ac2520bf7e0d9362b8da17d3c894da2db",
      "parents": [
        "11d85d7b2ecc72fe752bba55389e7d11907528af"
      ],
      "author": {
        "name": "Alan Cox",
        "email": "alan@linux.intel.com",
        "time": "Sat Sep 19 13:13:28 2009 -0700"
      },
      "committer": {
        "name": "Live-CD User",
        "email": "linux@linux.site",
        "time": "Sat Sep 19 13:13:28 2009 -0700"
      },
      "message": "serial: kill off uart_info\n\nWe moved this into uart_state, now move the fields out of the separate\nstructure and kill it off.\n\nSigned-off-by: Alan Cox \u003calan@linux.intel.com\u003e\nSigned-off-by: Greg Kroah-Hartman \u003cgregkh@suse.de\u003e\n"
    },
    {
      "commit": "2421c48bd74debb537de94c1bd15cbabab272aa1",
      "tree": "8e98a6011203769e3aa574f5b7e262a3ac54de32",
      "parents": [
        "be10eb7589337e5defbe214dae038a53dd21add8"
      ],
      "author": {
        "name": "Richard Röjfors",
        "email": "richard.rojfors.ext@mocean-labs.com",
        "time": "Mon Jun 22 18:43:03 2009 +0100"
      },
      "committer": {
        "name": "Linus Torvalds",
        "email": "torvalds@linux-foundation.org",
        "time": "Mon Jun 22 11:32:25 2009 -0700"
      },
      "message": "timbuart: Fix for tx_empty\n\nHardware updated to support TX FIFO empty.\n\nSigned-off-by: Richard Röjfors \u003crichard.rojfors.ext@mocean-labs.com\u003e\nSigned-off-by: Alan Cox \u003calan@linux.intel.com\u003e\nSigned-off-by: Linus Torvalds \u003ctorvalds@linux-foundation.org\u003e\n"
    },
    {
      "commit": "7d55deaf50182c47c1e805dc8cc85f2769f0673e",
      "tree": "6f8c262d6606be33b7023ff8f06f2a010d721366",
      "parents": [
        "34aec591847c696339189b070cce2a11f901cfea"
      ],
      "author": {
        "name": "Alan Cox",
        "email": "alan@linux.intel.com",
        "time": "Thu Jun 11 14:27:13 2009 +0100"
      },
      "committer": {
        "name": "Linus Torvalds",
        "email": "torvalds@linux-foundation.org",
        "time": "Thu Jun 11 08:51:06 2009 -0700"
      },
      "message": "timbuart: Fix the termios logic\n\nThe driver only handles speeds but it fails to return the current values\nfor the hardware features it does not support.\n\nSigned-off-by: Alan Cox \u003calan@linux.intel.com\u003e\nSigned-off-by: Linus Torvalds \u003ctorvalds@linux-foundation.org\u003e\n"
    },
    {
      "commit": "34aec591847c696339189b070cce2a11f901cfea",
      "tree": "b371a780186becf6daba7c229cb74821b020a879",
      "parents": [
        "e960bf73ddd73714bcfbadb1717e53ecda9924cb"
      ],
      "author": {
        "name": "Richard Röjfors",
        "email": "richard.rojfors.ext@mocean-labs.com",
        "time": "Thu Jun 11 14:05:39 2009 +0100"
      },
      "committer": {
        "name": "Linus Torvalds",
        "email": "torvalds@linux-foundation.org",
        "time": "Thu Jun 11 08:51:06 2009 -0700"
      },
      "message": "serial: Added Timberdale UART driver\n\nDriver for the UART found in the Timberdale FPGA\n\nSigned-off-by: Richard Röjfors \u003crichard.rojfors.ext@mocean-labs.com\u003e\nSigned-off-by: Alan Cox \u003calan@linux.intel.com\u003e\nSigned-off-by: Linus Torvalds \u003ctorvalds@linux-foundation.org\u003e\n"
    }
  ]
}