Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/arch/arm/boot/compressed/head-sharpsl.S b/arch/arm/boot/compressed/head-sharpsl.S
new file mode 100644
index 0000000..d6bf8a2
--- /dev/null
+++ b/arch/arm/boot/compressed/head-sharpsl.S
@@ -0,0 +1,92 @@
+/*
+ * linux/arch/arm/boot/compressed/head-sharpsl.S
+ *
+ * Copyright (C) 2004-2005 Richard Purdie <rpurdie@rpsys.net>
+ *
+ * Sharp's bootloader doesn't pass any kind of machine ID
+ * so we have to figure out the machine for ourselves...
+ *
+ * Support for Poodle, Corgi (SL-C700), Shepherd (SL-C750)
+ * and Husky (SL-C760).
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/linkage.h>
+#include <asm/mach-types.h>
+
+#ifndef CONFIG_PXA_SHARPSL
+#error What am I doing here...
+#endif
+
+ .section ".start", "ax"
+
+__SharpSL_start:
+
+ ldr r1, .W100ADDR @ Base address of w100 chip + regs offset
+
+ mov r6, #0x31 @ Load Magic Init value
+ str r6, [r1, #0x280] @ to SCRATCH_UMSK
+ mov r5, #0x3000
+.W100LOOP:
+ subs r5, r5, #1
+ bne .W100LOOP
+ mov r6, #0x30 @ Load 2nd Magic Init value
+ str r6, [r1, #0x280] @ to SCRATCH_UMSK
+
+ ldr r6, [r1, #0] @ Load Chip ID
+ ldr r3, .W100ID
+ ldr r7, .POODLEID
+ cmp r6, r3
+ bne .SHARPEND @ We have no w100 - Poodle
+
+ mrc p15, 0, r6, c0, c0 @ Get Processor ID
+ and r6, r6, #0xffffff00
+ ldr r7, .CORGIID
+ ldr r3, .PXA255ID
+ cmp r6, r3
+ blo .SHARPEND @ We have a PXA250 - Corgi
+
+ mov r1, #0x0c000000 @ Base address of NAND chip
+ ldrb r3, [r1, #24] @ Load FLASHCTL
+ bic r3, r3, #0x11 @ SET NCE
+ orr r3, r3, #0x0a @ SET CLR + FLWP
+ strb r3, [r1, #24] @ Save to FLASHCTL
+ mov r2, #0x90 @ Command "readid"
+ strb r2, [r1, #20] @ Save to FLASHIO
+ bic r3, r3, #2 @ CLR CLE
+ orr r3, r3, #4 @ SET ALE
+ strb r3, [r1, #24] @ Save to FLASHCTL
+ mov r2, #0 @ Address 0x00
+ strb r2, [r1, #20] @ Save to FLASHIO
+ bic r3, r3, #4 @ CLR ALE
+ strb r3, [r1, #24] @ Save to FLASHCTL
+.SHARP1:
+ ldrb r3, [r1, #24] @ Load FLASHCTL
+ tst r3, #32 @ Is chip ready?
+ beq .SHARP1
+ ldrb r2, [r1, #20] @ NAND Manufacturer ID
+ ldrb r3, [r1, #20] @ NAND Chip ID
+ ldr r7, .SHEPHERDID
+ cmp r3, #0x76 @ 64MiB flash
+ beq .SHARPEND @ We have Shepherd
+ ldr r7, .HUSKYID @ Must be Husky
+ b .SHARPEND
+
+.PXA255ID:
+ .word 0x69052d00 @ PXA255 Processor ID
+.W100ID:
+ .word 0x57411002 @ w100 Chip ID
+.W100ADDR:
+ .word 0x08010000 @ w100 Chip ID Reg Address
+.POODLEID:
+ .word MACH_TYPE_POODLE
+.CORGIID:
+ .word MACH_TYPE_CORGI
+.SHEPHERDID:
+ .word MACH_TYPE_SHEPHERD
+.HUSKYID:
+ .word MACH_TYPE_HUSKY
+.SHARPEND:
+
+