Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/arch/arm/mach-ixp4xx/common-pci.c b/arch/arm/mach-ixp4xx/common-pci.c
new file mode 100644
index 0000000..94bcdb9
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/common-pci.c
@@ -0,0 +1,527 @@
+/*
+ * arch/arm/mach-ixp4xx/common-pci.c
+ *
+ * IXP4XX PCI routines for all platforms
+ *
+ * Maintainer: Deepak Saxena <dsaxena@plexity.net>
+ *
+ * Copyright (C) 2002 Intel Corporation.
+ * Copyright (C) 2003 Greg Ungerer <gerg@snapgear.com>
+ * Copyright (C) 2003-2004 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/sched.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/mm.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <asm/dma-mapping.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/sizes.h>
+#include <asm/system.h>
+#include <asm/mach/pci.h>
+#include <asm/hardware.h>
+
+
+/*
+ * IXP4xx PCI read function is dependent on whether we are
+ * running A0 or B0 (AppleGate) silicon.
+ */
+int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data);
+
+/*
+ * Base address for PCI regsiter region
+ */
+unsigned long ixp4xx_pci_reg_base = 0;
+
+/*
+ * PCI cfg an I/O routines are done by programming a
+ * command/byte enable register, and then read/writing
+ * the data from a data regsiter. We need to ensure
+ * these transactions are atomic or we will end up
+ * with corrupt data on the bus or in a driver.
+ */
+static DEFINE_SPINLOCK(ixp4xx_pci_lock);
+
+/*
+ * Read from PCI config space
+ */
+static void crp_read(u32 ad_cbe, u32 *data)
+{
+ unsigned long flags;
+ spin_lock_irqsave(&ixp4xx_pci_lock, flags);
+ *PCI_CRP_AD_CBE = ad_cbe;
+ *data = *PCI_CRP_RDATA;
+ spin_unlock_irqrestore(&ixp4xx_pci_lock, flags);
+}
+
+/*
+ * Write to PCI config space
+ */
+static void crp_write(u32 ad_cbe, u32 data)
+{
+ unsigned long flags;
+ spin_lock_irqsave(&ixp4xx_pci_lock, flags);
+ *PCI_CRP_AD_CBE = CRP_AD_CBE_WRITE | ad_cbe;
+ *PCI_CRP_WDATA = data;
+ spin_unlock_irqrestore(&ixp4xx_pci_lock, flags);
+}
+
+static inline int check_master_abort(void)
+{
+ /* check Master Abort bit after access */
+ unsigned long isr = *PCI_ISR;
+
+ if (isr & PCI_ISR_PFE) {
+ /* make sure the Master Abort bit is reset */
+ *PCI_ISR = PCI_ISR_PFE;
+ pr_debug("%s failed\n", __FUNCTION__);
+ return 1;
+ }
+
+ return 0;
+}
+
+int ixp4xx_pci_read_errata(u32 addr, u32 cmd, u32* data)
+{
+ unsigned long flags;
+ int retval = 0;
+ int i;
+
+ spin_lock_irqsave(&ixp4xx_pci_lock, flags);
+
+ *PCI_NP_AD = addr;
+
+ /*
+ * PCI workaround - only works if NP PCI space reads have
+ * no side effects!!! Read 8 times. last one will be good.
+ */
+ for (i = 0; i < 8; i++) {
+ *PCI_NP_CBE = cmd;
+ *data = *PCI_NP_RDATA;
+ *data = *PCI_NP_RDATA;
+ }
+
+ if(check_master_abort())
+ retval = 1;
+
+ spin_unlock_irqrestore(&ixp4xx_pci_lock, flags);
+ return retval;
+}
+
+int ixp4xx_pci_read_no_errata(u32 addr, u32 cmd, u32* data)
+{
+ unsigned long flags;
+ int retval = 0;
+
+ spin_lock_irqsave(&ixp4xx_pci_lock, flags);
+
+ *PCI_NP_AD = addr;
+
+ /* set up and execute the read */
+ *PCI_NP_CBE = cmd;
+
+ /* the result of the read is now in NP_RDATA */
+ *data = *PCI_NP_RDATA;
+
+ if(check_master_abort())
+ retval = 1;
+
+ spin_unlock_irqrestore(&ixp4xx_pci_lock, flags);
+ return retval;
+}
+
+int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data)
+{
+ unsigned long flags;
+ int retval = 0;
+
+ spin_lock_irqsave(&ixp4xx_pci_lock, flags);
+
+ *PCI_NP_AD = addr;
+
+ /* set up the write */
+ *PCI_NP_CBE = cmd;
+
+ /* execute the write by writing to NP_WDATA */
+ *PCI_NP_WDATA = data;
+
+ if(check_master_abort())
+ retval = 1;
+
+ spin_unlock_irqrestore(&ixp4xx_pci_lock, flags);
+ return retval;
+}
+
+static u32 ixp4xx_config_addr(u8 bus_num, u16 devfn, int where)
+{
+ u32 addr;
+ if (!bus_num) {
+ /* type 0 */
+ addr = BIT(32-PCI_SLOT(devfn)) | ((PCI_FUNC(devfn)) << 8) |
+ (where & ~3);
+ } else {
+ /* type 1 */
+ addr = (bus_num << 16) | ((PCI_SLOT(devfn)) << 11) |
+ ((PCI_FUNC(devfn)) << 8) | (where & ~3) | 1;
+ }
+ return addr;
+}
+
+/*
+ * Mask table, bits to mask for quantity of size 1, 2 or 4 bytes.
+ * 0 and 3 are not valid indexes...
+ */
+static u32 bytemask[] = {
+ /*0*/ 0,
+ /*1*/ 0xff,
+ /*2*/ 0xffff,
+ /*3*/ 0,
+ /*4*/ 0xffffffff,
+};
+
+static u32 local_byte_lane_enable_bits(u32 n, int size)
+{
+ if (size == 1)
+ return (0xf & ~BIT(n)) << CRP_AD_CBE_BESL;
+ if (size == 2)
+ return (0xf & ~(BIT(n) | BIT(n+1))) << CRP_AD_CBE_BESL;
+ if (size == 4)
+ return 0;
+ return 0xffffffff;
+}
+
+static int local_read_config(int where, int size, u32 *value)
+{
+ u32 n, data;
+ pr_debug("local_read_config from %d size %d\n", where, size);
+ n = where % 4;
+ crp_read(where & ~3, &data);
+ *value = (data >> (8*n)) & bytemask[size];
+ pr_debug("local_read_config read %#x\n", *value);
+ return PCIBIOS_SUCCESSFUL;
+}
+
+static int local_write_config(int where, int size, u32 value)
+{
+ u32 n, byte_enables, data;
+ pr_debug("local_write_config %#x to %d size %d\n", value, where, size);
+ n = where % 4;
+ byte_enables = local_byte_lane_enable_bits(n, size);
+ if (byte_enables == 0xffffffff)
+ return PCIBIOS_BAD_REGISTER_NUMBER;
+ data = value << (8*n);
+ crp_write((where & ~3) | byte_enables, data);
+ return PCIBIOS_SUCCESSFUL;
+}
+
+static u32 byte_lane_enable_bits(u32 n, int size)
+{
+ if (size == 1)
+ return (0xf & ~BIT(n)) << 4;
+ if (size == 2)
+ return (0xf & ~(BIT(n) | BIT(n+1))) << 4;
+ if (size == 4)
+ return 0;
+ return 0xffffffff;
+}
+
+static int ixp4xx_pci_read_config(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 *value)
+{
+ u32 n, byte_enables, addr, data;
+ u8 bus_num = bus->number;
+
+ pr_debug("read_config from %d size %d dev %d:%d:%d\n", where, size,
+ bus_num, PCI_SLOT(devfn), PCI_FUNC(devfn));
+
+ *value = 0xffffffff;
+ n = where % 4;
+ byte_enables = byte_lane_enable_bits(n, size);
+ if (byte_enables == 0xffffffff)
+ return PCIBIOS_BAD_REGISTER_NUMBER;
+
+ addr = ixp4xx_config_addr(bus_num, devfn, where);
+ if (ixp4xx_pci_read(addr, byte_enables | NP_CMD_CONFIGREAD, &data))
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ *value = (data >> (8*n)) & bytemask[size];
+ pr_debug("read_config_byte read %#x\n", *value);
+ return PCIBIOS_SUCCESSFUL;
+}
+
+static int ixp4xx_pci_write_config(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 value)
+{
+ u32 n, byte_enables, addr, data;
+ u8 bus_num = bus->number;
+
+ pr_debug("write_config_byte %#x to %d size %d dev %d:%d:%d\n", value, where,
+ size, bus_num, PCI_SLOT(devfn), PCI_FUNC(devfn));
+
+ n = where % 4;
+ byte_enables = byte_lane_enable_bits(n, size);
+ if (byte_enables == 0xffffffff)
+ return PCIBIOS_BAD_REGISTER_NUMBER;
+
+ addr = ixp4xx_config_addr(bus_num, devfn, where);
+ data = value << (8*n);
+ if (ixp4xx_pci_write(addr, byte_enables | NP_CMD_CONFIGWRITE, data))
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops ixp4xx_ops = {
+ .read = ixp4xx_pci_read_config,
+ .write = ixp4xx_pci_write_config,
+};
+
+/*
+ * PCI abort handler
+ */
+static int abort_handler(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
+{
+ u32 isr, status;
+
+ isr = *PCI_ISR;
+ local_read_config(PCI_STATUS, 2, &status);
+ pr_debug("PCI: abort_handler addr = %#lx, isr = %#x, "
+ "status = %#x\n", addr, isr, status);
+
+ /* make sure the Master Abort bit is reset */
+ *PCI_ISR = PCI_ISR_PFE;
+ status |= PCI_STATUS_REC_MASTER_ABORT;
+ local_write_config(PCI_STATUS, 2, status);
+
+ /*
+ * If it was an imprecise abort, then we need to correct the
+ * return address to be _after_ the instruction.
+ */
+ if (fsr & (1 << 10))
+ regs->ARM_pc += 4;
+
+ return 0;
+}
+
+
+/*
+ * Setup DMA mask to 64MB on PCI devices. Ignore all other devices.
+ */
+static int ixp4xx_pci_platform_notify(struct device *dev)
+{
+ if(dev->bus == &pci_bus_type) {
+ *dev->dma_mask = SZ_64M - 1;
+ dev->coherent_dma_mask = SZ_64M - 1;
+ dmabounce_register_dev(dev, 2048, 4096);
+ }
+ return 0;
+}
+
+static int ixp4xx_pci_platform_notify_remove(struct device *dev)
+{
+ if(dev->bus == &pci_bus_type) {
+ dmabounce_unregister_dev(dev);
+ }
+ return 0;
+}
+
+int dma_needs_bounce(struct device *dev, dma_addr_t dma_addr, size_t size)
+{
+ return (dev->bus == &pci_bus_type ) && ((dma_addr + size) >= SZ_64M);
+}
+
+void __init ixp4xx_pci_preinit(void)
+{
+ unsigned long processor_id;
+
+ asm("mrc p15, 0, %0, cr0, cr0, 0;" : "=r"(processor_id) :);
+
+ /*
+ * Determine which PCI read method to use.
+ * Rev 0 IXP425 requires workaround.
+ */
+ if (!(processor_id & 0xf) && !cpu_is_ixp46x()) {
+ printk("PCI: IXP42x A0 silicon detected - "
+ "PCI Non-Prefetch Workaround Enabled\n");
+ ixp4xx_pci_read = ixp4xx_pci_read_errata;
+ } else
+ ixp4xx_pci_read = ixp4xx_pci_read_no_errata;
+
+
+ /* hook in our fault handler for PCI errors */
+ hook_fault_code(16+6, abort_handler, SIGBUS, "imprecise external abort");
+
+ pr_debug("setup PCI-AHB(inbound) and AHB-PCI(outbound) address mappings\n");
+
+ /*
+ * We use identity AHB->PCI address translation
+ * in the 0x48000000 to 0x4bffffff address space
+ */
+ *PCI_PCIMEMBASE = 0x48494A4B;
+
+ /*
+ * We also use identity PCI->AHB address translation
+ * in 4 16MB BARs that begin at the physical memory start
+ */
+ *PCI_AHBMEMBASE = (PHYS_OFFSET & 0xFF000000) +
+ ((PHYS_OFFSET & 0xFF000000) >> 8) +
+ ((PHYS_OFFSET & 0xFF000000) >> 16) +
+ ((PHYS_OFFSET & 0xFF000000) >> 24) +
+ 0x00010203;
+
+ if (*PCI_CSR & PCI_CSR_HOST) {
+ printk("PCI: IXP4xx is host\n");
+
+ pr_debug("setup BARs in controller\n");
+
+ /*
+ * We configure the PCI inbound memory windows to be
+ * 1:1 mapped to SDRAM
+ */
+ local_write_config(PCI_BASE_ADDRESS_0, 4, PHYS_OFFSET + 0x00000000);
+ local_write_config(PCI_BASE_ADDRESS_1, 4, PHYS_OFFSET + 0x01000000);
+ local_write_config(PCI_BASE_ADDRESS_2, 4, PHYS_OFFSET + 0x02000000);
+ local_write_config(PCI_BASE_ADDRESS_3, 4, PHYS_OFFSET + 0x03000000);
+
+ /*
+ * Enable CSR window at 0xff000000.
+ */
+ local_write_config(PCI_BASE_ADDRESS_4, 4, 0xff000008);
+
+ /*
+ * Enable the IO window to be way up high, at 0xfffffc00
+ */
+ local_write_config(PCI_BASE_ADDRESS_5, 4, 0xfffffc01);
+ } else {
+ printk("PCI: IXP4xx is target - No bus scan performed\n");
+ }
+
+ printk("PCI: IXP4xx Using %s access for memory space\n",
+#ifndef CONFIG_IXP4XX_INDIRECT_PCI
+ "direct"
+#else
+ "indirect"
+#endif
+ );
+
+ pr_debug("clear error bits in ISR\n");
+ *PCI_ISR = PCI_ISR_PSE | PCI_ISR_PFE | PCI_ISR_PPE | PCI_ISR_AHBE;
+
+ /*
+ * Set Initialize Complete in PCI Control Register: allow IXP4XX to
+ * respond to PCI configuration cycles. Specify that the AHB bus is
+ * operating in big endian mode. Set up byte lane swapping between
+ * little-endian PCI and the big-endian AHB bus
+ */
+#ifdef __ARMEB__
+ *PCI_CSR = PCI_CSR_IC | PCI_CSR_ABE | PCI_CSR_PDS | PCI_CSR_ADS;
+#else
+ *PCI_CSR = PCI_CSR_IC;
+#endif
+
+ pr_debug("DONE\n");
+}
+
+int ixp4xx_setup(int nr, struct pci_sys_data *sys)
+{
+ struct resource *res;
+
+ if (nr >= 1)
+ return 0;
+
+ res = kmalloc(sizeof(*res) * 2, GFP_KERNEL);
+ if (res == NULL) {
+ /*
+ * If we're out of memory this early, something is wrong,
+ * so we might as well catch it here.
+ */
+ panic("PCI: unable to allocate resources?\n");
+ }
+ memset(res, 0, sizeof(*res) * 2);
+
+ local_write_config(PCI_COMMAND, 2, PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
+
+ res[0].name = "PCI I/O Space";
+ res[0].start = 0x00001000;
+ res[0].end = 0xffff0000;
+ res[0].flags = IORESOURCE_IO;
+
+ res[1].name = "PCI Memory Space";
+ res[1].start = 0x48000000;
+#ifndef CONFIG_IXP4XX_INDIRECT_PCI
+ res[1].end = 0x4bffffff;
+#else
+ res[1].end = 0x4fffffff;
+#endif
+ res[1].flags = IORESOURCE_MEM;
+
+ request_resource(&ioport_resource, &res[0]);
+ request_resource(&iomem_resource, &res[1]);
+
+ sys->resource[0] = &res[0];
+ sys->resource[1] = &res[1];
+ sys->resource[2] = NULL;
+
+ platform_notify = ixp4xx_pci_platform_notify;
+ platform_notify_remove = ixp4xx_pci_platform_notify_remove;
+
+ return 1;
+}
+
+struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys)
+{
+ return pci_scan_bus(sys->busnr, &ixp4xx_ops, sys);
+}
+
+/*
+ * We override these so we properly do dmabounce otherwise drivers
+ * are able to set the dma_mask to 0xffffffff and we can no longer
+ * trap bounces. :(
+ *
+ * We just return true on everyhing except for < 64MB in which case
+ * we will fail miseralby and die since we can't handle that case.
+ */
+int
+pci_set_dma_mask(struct pci_dev *dev, u64 mask)
+{
+ if (mask >= SZ_64M - 1 )
+ return 0;
+
+ return -EIO;
+}
+
+int
+pci_dac_set_dma_mask(struct pci_dev *dev, u64 mask)
+{
+ if (mask >= SZ_64M - 1 )
+ return 0;
+
+ return -EIO;
+}
+
+int
+pci_set_consistent_dma_mask(struct pci_dev *dev, u64 mask)
+{
+ if (mask >= SZ_64M - 1 )
+ return 0;
+
+ return -EIO;
+}
+
+EXPORT_SYMBOL(pci_set_dma_mask);
+EXPORT_SYMBOL(pci_dac_set_dma_mask);
+EXPORT_SYMBOL(pci_set_consistent_dma_mask);
+EXPORT_SYMBOL(ixp4xx_pci_read);
+EXPORT_SYMBOL(ixp4xx_pci_write);
+