Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
diff --git a/arch/m68k/kernel/bios32.c b/arch/m68k/kernel/bios32.c
new file mode 100644
index 0000000..a901685
--- /dev/null
+++ b/arch/m68k/kernel/bios32.c
@@ -0,0 +1,515 @@
+/*
+ * bios32.c - PCI BIOS functions for m68k systems.
+ *
+ * Written by Wout Klaren.
+ *
+ * Based on the DEC Alpha bios32.c by Dave Rusling and David Mosberger.
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+
+#if 0
+# define DBG_DEVS(args)		printk args
+#else
+# define DBG_DEVS(args)
+#endif
+
+#ifdef CONFIG_PCI
+
+/*
+ * PCI support for Linux/m68k. Currently only the Hades is supported.
+ *
+ * The support for PCI bridges in the DEC Alpha version has
+ * been removed in this version.
+ */
+
+#include <linux/pci.h>
+#include <linux/slab.h>
+#include <linux/mm.h>
+
+#include <asm/io.h>
+#include <asm/pci.h>
+#include <asm/uaccess.h>
+
+#define KB		1024
+#define MB		(1024*KB)
+#define GB		(1024*MB)
+
+#define MAJOR_REV	0
+#define MINOR_REV	5
+
+/*
+ * Align VAL to ALIGN, which must be a power of two.
+ */
+
+#define ALIGN(val,align)	(((val) + ((align) - 1)) & ~((align) - 1))
+
+/*
+ * Offsets relative to the I/O and memory base addresses from where resources
+ * are allocated.
+ */
+
+#define IO_ALLOC_OFFSET		0x00004000
+#define MEM_ALLOC_OFFSET	0x04000000
+
+/*
+ * Declarations of hardware specific initialisation functions.
+ */
+
+extern struct pci_bus_info *init_hades_pci(void);
+
+/*
+ * Bus info structure of the PCI bus. A pointer to this structure is
+ * put in the sysdata member of the pci_bus structure.
+ */
+
+static struct pci_bus_info *bus_info;
+
+static int pci_modify = 1;		/* If set, layout the PCI bus ourself. */
+static int skip_vga;			/* If set do not modify base addresses
+					   of vga cards.*/
+static int disable_pci_burst;		/* If set do not allow PCI bursts. */
+
+static unsigned int io_base;
+static unsigned int mem_base;
+
+/*
+ * static void disable_dev(struct pci_dev *dev)
+ *
+ * Disable PCI device DEV so that it does not respond to I/O or memory
+ * accesses.
+ *
+ * Parameters:
+ *
+ * dev	- device to disable.
+ */
+
+static void __init disable_dev(struct pci_dev *dev)
+{
+	unsigned short cmd;
+
+	if (((dev->class >> 8 == PCI_CLASS_NOT_DEFINED_VGA) ||
+	     (dev->class >> 8 == PCI_CLASS_DISPLAY_VGA) ||
+	     (dev->class >> 8 == PCI_CLASS_DISPLAY_XGA)) && skip_vga)
+		return;
+
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+
+	cmd &= (~PCI_COMMAND_IO & ~PCI_COMMAND_MEMORY & ~PCI_COMMAND_MASTER);
+	pci_write_config_word(dev, PCI_COMMAND, cmd);
+}
+
+/*
+ * static void layout_dev(struct pci_dev *dev)
+ *
+ * Layout memory and I/O for a device.
+ *
+ * Parameters:
+ *
+ * device	- device to layout memory and I/O for.
+ */
+
+static void __init layout_dev(struct pci_dev *dev)
+{
+	unsigned short cmd;
+	unsigned int base, mask, size, reg;
+	unsigned int alignto;
+	int i;
+
+	/*
+	 * Skip video cards if requested.
+	 */
+
+	if (((dev->class >> 8 == PCI_CLASS_NOT_DEFINED_VGA) ||
+	     (dev->class >> 8 == PCI_CLASS_DISPLAY_VGA) ||
+	     (dev->class >> 8 == PCI_CLASS_DISPLAY_XGA)) && skip_vga)
+		return;
+
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+
+	for (reg = PCI_BASE_ADDRESS_0, i = 0; reg <= PCI_BASE_ADDRESS_5; reg += 4, i++)
+	{
+		/*
+		 * Figure out how much space and of what type this
+		 * device wants.
+		 */
+
+		pci_write_config_dword(dev, reg, 0xffffffff);
+		pci_read_config_dword(dev, reg, &base);
+
+		if (!base)
+		{
+			/* this base-address register is unused */
+			dev->resource[i].start = 0;
+			dev->resource[i].end = 0;
+			dev->resource[i].flags = 0;
+			continue;
+		}
+
+		/*
+		 * We've read the base address register back after
+		 * writing all ones and so now we must decode it.
+		 */
+
+		if (base & PCI_BASE_ADDRESS_SPACE_IO)
+		{
+			/*
+			 * I/O space base address register.
+			 */
+
+			cmd |= PCI_COMMAND_IO;
+
+			base &= PCI_BASE_ADDRESS_IO_MASK;
+			mask = (~base << 1) | 0x1;
+			size = (mask & base) & 0xffffffff;
+
+			/*
+			 * Align to multiple of size of minimum base.
+			 */
+
+			alignto = max_t(unsigned int, 0x040, size);
+			base = ALIGN(io_base, alignto);
+			io_base = base + size;
+			pci_write_config_dword(dev, reg, base | PCI_BASE_ADDRESS_SPACE_IO);
+
+			dev->resource[i].start = base;
+			dev->resource[i].end = dev->resource[i].start + size - 1;
+			dev->resource[i].flags = IORESOURCE_IO | PCI_BASE_ADDRESS_SPACE_IO;
+
+			DBG_DEVS(("layout_dev: IO address: %lX\n", base));
+		}
+		else
+		{
+			unsigned int type;
+
+			/*
+			 * Memory space base address register.
+			 */
+
+			cmd |= PCI_COMMAND_MEMORY;
+			type = base & PCI_BASE_ADDRESS_MEM_TYPE_MASK;
+			base &= PCI_BASE_ADDRESS_MEM_MASK;
+			mask = (~base << 1) | 0x1;
+			size = (mask & base) & 0xffffffff;
+			switch (type)
+			{
+			case PCI_BASE_ADDRESS_MEM_TYPE_32:
+			case PCI_BASE_ADDRESS_MEM_TYPE_64:
+				break;
+
+			case PCI_BASE_ADDRESS_MEM_TYPE_1M:
+				printk("bios32 WARNING: slot %d, function %d "
+				       "requests memory below 1MB---don't "
+				       "know how to do that.\n",
+				       PCI_SLOT(dev->devfn),
+				       PCI_FUNC(dev->devfn));
+				continue;
+			}
+
+			/*
+			 * Align to multiple of size of minimum base.
+			 */
+
+			alignto = max_t(unsigned int, 0x1000, size);
+			base = ALIGN(mem_base, alignto);
+			mem_base = base + size;
+			pci_write_config_dword(dev, reg, base);
+
+			dev->resource[i].start = base;
+			dev->resource[i].end = dev->resource[i].start + size - 1;
+			dev->resource[i].flags = IORESOURCE_MEM;
+
+			if (type == PCI_BASE_ADDRESS_MEM_TYPE_64)
+			{
+				/*
+				 * 64-bit address, set the highest 32 bits
+				 * to zero.
+				 */
+
+				reg += 4;
+				pci_write_config_dword(dev, reg, 0);
+
+				i++;
+				dev->resource[i].start = 0;
+				dev->resource[i].end = 0;
+				dev->resource[i].flags = 0;
+			}
+		}
+	}
+
+	/*
+	 * Enable device:
+	 */
+
+	if (dev->class >> 8 == PCI_CLASS_NOT_DEFINED ||
+	    dev->class >> 8 == PCI_CLASS_NOT_DEFINED_VGA ||
+	    dev->class >> 8 == PCI_CLASS_DISPLAY_VGA ||
+	    dev->class >> 8 == PCI_CLASS_DISPLAY_XGA)
+	{
+		/*
+		 * All of these (may) have I/O scattered all around
+		 * and may not use i/o-base address registers at all.
+		 * So we just have to always enable I/O to these
+		 * devices.
+		 */
+		cmd |= PCI_COMMAND_IO;
+	}
+
+	pci_write_config_word(dev, PCI_COMMAND, cmd | PCI_COMMAND_MASTER);
+
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, (disable_pci_burst) ? 0 : 32);
+
+	if (bus_info != NULL)
+		bus_info->conf_device(dev);	/* Machine dependent configuration. */
+
+	DBG_DEVS(("layout_dev: bus %d  slot 0x%x  VID 0x%x  DID 0x%x  class 0x%x\n",
+		  dev->bus->number, PCI_SLOT(dev->devfn), dev->vendor, dev->device, dev->class));
+}
+
+/*
+ * static void layout_bus(struct pci_bus *bus)
+ *
+ * Layout memory and I/O for all devices on the given bus.
+ *
+ * Parameters:
+ *
+ * bus	- bus.
+ */
+
+static void __init layout_bus(struct pci_bus *bus)
+{
+	unsigned int bio, bmem;
+	struct pci_dev *dev;
+
+	DBG_DEVS(("layout_bus: starting bus %d\n", bus->number));
+
+	if (!bus->devices && !bus->children)
+		return;
+
+	/*
+	 * Align the current bases on appropriate boundaries (4K for
+	 * IO and 1MB for memory).
+	 */
+
+	bio = io_base = ALIGN(io_base, 4*KB);
+	bmem = mem_base = ALIGN(mem_base, 1*MB);
+
+	/*
+	 * PCI devices might have been setup by a PCI BIOS emulation
+	 * running under TOS. In these cases there is a
+	 * window during which two devices may have an overlapping
+	 * address range. To avoid this causing trouble, we first
+	 * turn off the I/O and memory address decoders for all PCI
+	 * devices.  They'll be re-enabled only once all address
+	 * decoders are programmed consistently.
+	 */
+
+	DBG_DEVS(("layout_bus: disable_dev for bus %d\n", bus->number));
+
+	for (dev = bus->devices; dev; dev = dev->sibling)
+	{
+		if ((dev->class >> 16 != PCI_BASE_CLASS_BRIDGE) ||
+		    (dev->class >> 8 == PCI_CLASS_BRIDGE_PCMCIA))
+			disable_dev(dev);
+	}
+
+	/*
+	 * Allocate space to each device:
+	 */
+
+	DBG_DEVS(("layout_bus: starting bus %d devices\n", bus->number));
+
+	for (dev = bus->devices; dev; dev = dev->sibling)
+	{
+		if ((dev->class >> 16 != PCI_BASE_CLASS_BRIDGE) ||
+		    (dev->class >> 8 == PCI_CLASS_BRIDGE_PCMCIA))
+			layout_dev(dev);
+	}
+
+	DBG_DEVS(("layout_bus: bus %d finished\n", bus->number));
+}
+
+/*
+ * static void pcibios_fixup(void)
+ *
+ * Layout memory and I/O of all devices on the PCI bus if 'pci_modify' is
+ * true. This might be necessary because not every m68k machine with a PCI
+ * bus has a PCI BIOS. This function should be called right after
+ * pci_scan_bus() in pcibios_init().
+ */
+
+static void __init pcibios_fixup(void)
+{
+	if (pci_modify)
+	{
+		/*
+		 * Set base addresses for allocation of I/O and memory space.
+		 */
+
+		io_base = bus_info->io_space.start + IO_ALLOC_OFFSET;
+		mem_base = bus_info->mem_space.start + MEM_ALLOC_OFFSET;
+
+		/*
+		 * Scan the tree, allocating PCI memory and I/O space.
+		 */
+
+		layout_bus(pci_bus_b(pci_root.next));
+	}
+
+	/*
+	 * Fix interrupt assignments, etc.
+	 */
+
+	bus_info->fixup(pci_modify);
+}
+
+/*
+ * static void pcibios_claim_resources(struct pci_bus *bus)
+ *
+ * Claim all resources that are assigned to devices on the given bus.
+ *
+ * Parameters:
+ *
+ * bus	- bus.
+ */
+
+static void __init pcibios_claim_resources(struct pci_bus *bus)
+{
+	struct pci_dev *dev;
+	int i;
+
+	while (bus)
+	{
+		for (dev = bus->devices; (dev != NULL); dev = dev->sibling)
+		{
+			for (i = 0; i < PCI_NUM_RESOURCES; i++)
+			{
+				struct resource *r = &dev->resource[i];
+				struct resource *pr;
+				struct pci_bus_info *bus_info = (struct pci_bus_info *) dev->sysdata;
+
+				if ((r->start == 0) || (r->parent != NULL))
+					continue;
+#if 1
+				if (r->flags & IORESOURCE_IO)
+					pr = &bus_info->io_space;
+				else
+					pr = &bus_info->mem_space;
+#else
+				if (r->flags & IORESOURCE_IO)
+					pr = &ioport_resource;
+				else
+					pr = &iomem_resource;
+#endif
+				if (request_resource(pr, r) < 0)
+				{
+					printk(KERN_ERR "PCI: Address space collision on region %d of device %s\n", i, dev->name);
+				}
+			}
+		}
+
+		if (bus->children)
+			pcibios_claim_resources(bus->children);
+
+		bus = bus->next;
+	}
+}
+
+/*
+ * int pcibios_assign_resource(struct pci_dev *dev, int i)
+ *
+ * Assign a new address to a PCI resource.
+ *
+ * Parameters:
+ *
+ * dev	- device.
+ * i	- resource.
+ *
+ * Result: 0 if successful.
+ */
+
+int __init pcibios_assign_resource(struct pci_dev *dev, int i)
+{
+	struct resource *r = &dev->resource[i];
+	struct resource *pr = pci_find_parent_resource(dev, r);
+	unsigned long size = r->end + 1;
+
+	if (!pr)
+		return -EINVAL;
+
+	if (r->flags & IORESOURCE_IO)
+	{
+		if (size > 0x100)
+			return -EFBIG;
+
+		if (allocate_resource(pr, r, size, bus_info->io_space.start +
+				      IO_ALLOC_OFFSET,  bus_info->io_space.end, 1024))
+			return -EBUSY;
+	}
+	else
+	{
+		if (allocate_resource(pr, r, size, bus_info->mem_space.start +
+				      MEM_ALLOC_OFFSET, bus_info->mem_space.end, size))
+			return -EBUSY;
+	}
+
+	if (i < 6)
+		pci_write_config_dword(dev, PCI_BASE_ADDRESS_0 + 4 * i, r->start);
+
+	return 0;
+}
+
+void __init pcibios_fixup_bus(struct pci_bus *bus)
+{
+	struct pci_dev *dev;
+	void *sysdata;
+
+	sysdata = (bus->parent) ? bus->parent->sysdata : bus->sysdata;
+
+	for (dev = bus->devices; (dev != NULL); dev = dev->sibling)
+		dev->sysdata = sysdata;
+}
+
+void __init pcibios_init(void)
+{
+	printk("Linux/m68k PCI BIOS32 revision %x.%02x\n", MAJOR_REV, MINOR_REV);
+
+	bus_info = NULL;
+#ifdef CONFIG_HADES
+	if (MACH_IS_HADES)
+		bus_info = init_hades_pci();
+#endif
+	if (bus_info != NULL)
+	{
+		printk("PCI: Probing PCI hardware\n");
+		pci_scan_bus(0, bus_info->m68k_pci_ops, bus_info);
+		pcibios_fixup();
+		pcibios_claim_resources(pci_root);
+	}
+	else
+		printk("PCI: No PCI bus detected\n");
+}
+
+char * __init pcibios_setup(char *str)
+{
+	if (!strcmp(str, "nomodify"))
+	{
+		pci_modify = 0;
+		return NULL;
+	}
+	else if (!strcmp(str, "skipvga"))
+	{
+		skip_vga = 1;
+		return NULL;
+	}
+	else if (!strcmp(str, "noburst"))
+	{
+		disable_pci_burst = 1;
+		return NULL;
+	}
+
+	return str;
+}
+#endif /* CONFIG_PCI */