diff --git a/drivers/char/stallion.c b/drivers/char/stallion.c
new file mode 100644
index 0000000..de16660
--- /dev/null
+++ b/drivers/char/stallion.c
@@ -0,0 +1,5197 @@
+/*****************************************************************************/
+
+/*
+ *	stallion.c  -- stallion multiport serial driver.
+ *
+ *	Copyright (C) 1996-1999  Stallion Technologies
+ *	Copyright (C) 1994-1996  Greg Ungerer.
+ *
+ *	This code is loosely based on the Linux serial driver, written by
+ *	Linus Torvalds, Theodore T'so and others.
+ *
+ *	This program is free software; you can redistribute it and/or modify
+ *	it under the terms of the GNU General Public License as published by
+ *	the Free Software Foundation; either version 2 of the License, or
+ *	(at your option) any later version.
+ *
+ *	This program is distributed in the hope that it will be useful,
+ *	but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *	GNU General Public License for more details.
+ *
+ *	You should have received a copy of the GNU General Public License
+ *	along with this program; if not, write to the Free Software
+ *	Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/*****************************************************************************/
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial.h>
+#include <linux/cd1400.h>
+#include <linux/sc26198.h>
+#include <linux/comstats.h>
+#include <linux/stallion.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/smp_lock.h>
+#include <linux/devfs_fs_kernel.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+
+#include <asm/io.h>
+#include <asm/uaccess.h>
+
+#ifdef CONFIG_PCI
+#include <linux/pci.h>
+#endif
+
+/*****************************************************************************/
+
+/*
+ *	Define different board types. Use the standard Stallion "assigned"
+ *	board numbers. Boards supported in this driver are abbreviated as
+ *	EIO = EasyIO and ECH = EasyConnection 8/32.
+ */
+#define	BRD_EASYIO	20
+#define	BRD_ECH		21
+#define	BRD_ECHMC	22
+#define	BRD_ECHPCI	26
+#define	BRD_ECH64PCI	27
+#define	BRD_EASYIOPCI	28
+
+/*
+ *	Define a configuration structure to hold the board configuration.
+ *	Need to set this up in the code (for now) with the boards that are
+ *	to be configured into the system. This is what needs to be modified
+ *	when adding/removing/modifying boards. Each line entry in the
+ *	stl_brdconf[] array is a board. Each line contains io/irq/memory
+ *	ranges for that board (as well as what type of board it is).
+ *	Some examples:
+ *		{ BRD_EASYIO, 0x2a0, 0, 0, 10, 0 },
+ *	This line would configure an EasyIO board (4 or 8, no difference),
+ *	at io address 2a0 and irq 10.
+ *	Another example:
+ *		{ BRD_ECH, 0x2a8, 0x280, 0, 12, 0 },
+ *	This line will configure an EasyConnection 8/32 board at primary io
+ *	address 2a8, secondary io address 280 and irq 12.
+ *	Enter as many lines into this array as you want (only the first 4
+ *	will actually be used!). Any combination of EasyIO and EasyConnection
+ *	boards can be specified. EasyConnection 8/32 boards can share their
+ *	secondary io addresses between each other.
+ *
+ *	NOTE: there is no need to put any entries in this table for PCI
+ *	boards. They will be found automatically by the driver - provided
+ *	PCI BIOS32 support is compiled into the kernel.
+ */
+
+typedef struct {
+	int		brdtype;
+	int		ioaddr1;
+	int		ioaddr2;
+	unsigned long	memaddr;
+	int		irq;
+	int		irqtype;
+} stlconf_t;
+
+static stlconf_t	stl_brdconf[] = {
+	/*{ BRD_EASYIO, 0x2a0, 0, 0, 10, 0 },*/
+};
+
+static int	stl_nrbrds = sizeof(stl_brdconf) / sizeof(stlconf_t);
+
+/*****************************************************************************/
+
+/*
+ *	Define some important driver characteristics. Device major numbers
+ *	allocated as per Linux Device Registry.
+ */
+#ifndef	STL_SIOMEMMAJOR
+#define	STL_SIOMEMMAJOR		28
+#endif
+#ifndef	STL_SERIALMAJOR
+#define	STL_SERIALMAJOR		24
+#endif
+#ifndef	STL_CALLOUTMAJOR
+#define	STL_CALLOUTMAJOR	25
+#endif
+
+/*
+ *	Set the TX buffer size. Bigger is better, but we don't want
+ *	to chew too much memory with buffers!
+ */
+#define	STL_TXBUFLOW		512
+#define	STL_TXBUFSIZE		4096
+
+/*****************************************************************************/
+
+/*
+ *	Define our local driver identity first. Set up stuff to deal with
+ *	all the local structures required by a serial tty driver.
+ */
+static char	*stl_drvtitle = "Stallion Multiport Serial Driver";
+static char	*stl_drvname = "stallion";
+static char	*stl_drvversion = "5.6.0";
+
+static struct tty_driver	*stl_serial;
+
+/*
+ *	We will need to allocate a temporary write buffer for chars that
+ *	come direct from user space. The problem is that a copy from user
+ *	space might cause a page fault (typically on a system that is
+ *	swapping!). All ports will share one buffer - since if the system
+ *	is already swapping a shared buffer won't make things any worse.
+ */
+static char			*stl_tmpwritebuf;
+static DECLARE_MUTEX(stl_tmpwritesem);
+
+/*
+ *	Define a local default termios struct. All ports will be created
+ *	with this termios initially. Basically all it defines is a raw port
+ *	at 9600, 8 data bits, 1 stop bit.
+ */
+static struct termios		stl_deftermios = {
+	.c_cflag	= (B9600 | CS8 | CREAD | HUPCL | CLOCAL),
+	.c_cc		= INIT_C_CC,
+};
+
+/*
+ *	Define global stats structures. Not used often, and can be
+ *	re-used for each stats call.
+ */
+static comstats_t	stl_comstats;
+static combrd_t		stl_brdstats;
+static stlbrd_t		stl_dummybrd;
+static stlport_t	stl_dummyport;
+
+/*
+ *	Define global place to put buffer overflow characters.
+ */
+static char		stl_unwanted[SC26198_RXFIFOSIZE];
+
+/*****************************************************************************/
+
+static stlbrd_t		*stl_brds[STL_MAXBRDS];
+
+/*
+ *	Per board state flags. Used with the state field of the board struct.
+ *	Not really much here!
+ */
+#define	BRD_FOUND	0x1
+
+/*
+ *	Define the port structure istate flags. These set of flags are
+ *	modified at interrupt time - so setting and reseting them needs
+ *	to be atomic. Use the bit clear/setting routines for this.
+ */
+#define	ASYI_TXBUSY	1
+#define	ASYI_TXLOW	2
+#define	ASYI_DCDCHANGE	3
+#define	ASYI_TXFLOWED	4
+
+/*
+ *	Define an array of board names as printable strings. Handy for
+ *	referencing boards when printing trace and stuff.
+ */
+static char	*stl_brdnames[] = {
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	"EasyIO",
+	"EC8/32-AT",
+	"EC8/32-MC",
+	(char *) NULL,
+	(char *) NULL,
+	(char *) NULL,
+	"EC8/32-PCI",
+	"EC8/64-PCI",
+	"EasyIO-PCI",
+};
+
+/*****************************************************************************/
+
+/*
+ *	Define some string labels for arguments passed from the module
+ *	load line. These allow for easy board definitions, and easy
+ *	modification of the io, memory and irq resoucres.
+ */
+static int	stl_nargs = 0;
+static char	*board0[4];
+static char	*board1[4];
+static char	*board2[4];
+static char	*board3[4];
+
+static char	**stl_brdsp[] = {
+	(char **) &board0,
+	(char **) &board1,
+	(char **) &board2,
+	(char **) &board3
+};
+
+/*
+ *	Define a set of common board names, and types. This is used to
+ *	parse any module arguments.
+ */
+
+typedef struct stlbrdtype {
+	char	*name;
+	int	type;
+} stlbrdtype_t;
+
+static stlbrdtype_t	stl_brdstr[] = {
+	{ "easyio", BRD_EASYIO },
+	{ "eio", BRD_EASYIO },
+	{ "20", BRD_EASYIO },
+	{ "ec8/32", BRD_ECH },
+	{ "ec8/32-at", BRD_ECH },
+	{ "ec8/32-isa", BRD_ECH },
+	{ "ech", BRD_ECH },
+	{ "echat", BRD_ECH },
+	{ "21", BRD_ECH },
+	{ "ec8/32-mc", BRD_ECHMC },
+	{ "ec8/32-mca", BRD_ECHMC },
+	{ "echmc", BRD_ECHMC },
+	{ "echmca", BRD_ECHMC },
+	{ "22", BRD_ECHMC },
+	{ "ec8/32-pc", BRD_ECHPCI },
+	{ "ec8/32-pci", BRD_ECHPCI },
+	{ "26", BRD_ECHPCI },
+	{ "ec8/64-pc", BRD_ECH64PCI },
+	{ "ec8/64-pci", BRD_ECH64PCI },
+	{ "ech-pci", BRD_ECH64PCI },
+	{ "echpci", BRD_ECH64PCI },
+	{ "echpc", BRD_ECH64PCI },
+	{ "27", BRD_ECH64PCI },
+	{ "easyio-pc", BRD_EASYIOPCI },
+	{ "easyio-pci", BRD_EASYIOPCI },
+	{ "eio-pci", BRD_EASYIOPCI },
+	{ "eiopci", BRD_EASYIOPCI },
+	{ "28", BRD_EASYIOPCI },
+};
+
+/*
+ *	Define the module agruments.
+ */
+MODULE_AUTHOR("Greg Ungerer");
+MODULE_DESCRIPTION("Stallion Multiport Serial Driver");
+MODULE_LICENSE("GPL");
+
+module_param_array(board0, charp, &stl_nargs, 0);
+MODULE_PARM_DESC(board0, "Board 0 config -> name[,ioaddr[,ioaddr2][,irq]]");
+module_param_array(board1, charp, &stl_nargs, 0);
+MODULE_PARM_DESC(board1, "Board 1 config -> name[,ioaddr[,ioaddr2][,irq]]");
+module_param_array(board2, charp, &stl_nargs, 0);
+MODULE_PARM_DESC(board2, "Board 2 config -> name[,ioaddr[,ioaddr2][,irq]]");
+module_param_array(board3, charp, &stl_nargs, 0);
+MODULE_PARM_DESC(board3, "Board 3 config -> name[,ioaddr[,ioaddr2][,irq]]");
+
+/*****************************************************************************/
+
+/*
+ *	Hardware ID bits for the EasyIO and ECH boards. These defines apply
+ *	to the directly accessible io ports of these boards (not the uarts -
+ *	they are in cd1400.h and sc26198.h).
+ */
+#define	EIO_8PORTRS	0x04
+#define	EIO_4PORTRS	0x05
+#define	EIO_8PORTDI	0x00
+#define	EIO_8PORTM	0x06
+#define	EIO_MK3		0x03
+#define	EIO_IDBITMASK	0x07
+
+#define	EIO_BRDMASK	0xf0
+#define	ID_BRD4		0x10
+#define	ID_BRD8		0x20
+#define	ID_BRD16	0x30
+
+#define	EIO_INTRPEND	0x08
+#define	EIO_INTEDGE	0x00
+#define	EIO_INTLEVEL	0x08
+#define	EIO_0WS		0x10
+
+#define	ECH_ID		0xa0
+#define	ECH_IDBITMASK	0xe0
+#define	ECH_BRDENABLE	0x08
+#define	ECH_BRDDISABLE	0x00
+#define	ECH_INTENABLE	0x01
+#define	ECH_INTDISABLE	0x00
+#define	ECH_INTLEVEL	0x02
+#define	ECH_INTEDGE	0x00
+#define	ECH_INTRPEND	0x01
+#define	ECH_BRDRESET	0x01
+
+#define	ECHMC_INTENABLE	0x01
+#define	ECHMC_BRDRESET	0x02
+
+#define	ECH_PNLSTATUS	2
+#define	ECH_PNL16PORT	0x20
+#define	ECH_PNLIDMASK	0x07
+#define	ECH_PNLXPID	0x40
+#define	ECH_PNLINTRPEND	0x80
+
+#define	ECH_ADDR2MASK	0x1e0
+
+/*
+ *	Define the vector mapping bits for the programmable interrupt board
+ *	hardware. These bits encode the interrupt for the board to use - it
+ *	is software selectable (except the EIO-8M).
+ */
+static unsigned char	stl_vecmap[] = {
+	0xff, 0xff, 0xff, 0x04, 0x06, 0x05, 0xff, 0x07,
+	0xff, 0xff, 0x00, 0x02, 0x01, 0xff, 0xff, 0x03
+};
+
+/*
+ *	Set up enable and disable macros for the ECH boards. They require
+ *	the secondary io address space to be activated and deactivated.
+ *	This way all ECH boards can share their secondary io region.
+ *	If this is an ECH-PCI board then also need to set the page pointer
+ *	to point to the correct page.
+ */
+#define	BRDENABLE(brdnr,pagenr)						\
+	if (stl_brds[(brdnr)]->brdtype == BRD_ECH)			\
+		outb((stl_brds[(brdnr)]->ioctrlval | ECH_BRDENABLE),	\
+			stl_brds[(brdnr)]->ioctrl);			\
+	else if (stl_brds[(brdnr)]->brdtype == BRD_ECHPCI)		\
+		outb((pagenr), stl_brds[(brdnr)]->ioctrl);
+
+#define	BRDDISABLE(brdnr)						\
+	if (stl_brds[(brdnr)]->brdtype == BRD_ECH)			\
+		outb((stl_brds[(brdnr)]->ioctrlval | ECH_BRDDISABLE),	\
+			stl_brds[(brdnr)]->ioctrl);
+
+#define	STL_CD1400MAXBAUD	230400
+#define	STL_SC26198MAXBAUD	460800
+
+#define	STL_BAUDBASE		115200
+#define	STL_CLOSEDELAY		(5 * HZ / 10)
+
+/*****************************************************************************/
+
+#ifdef CONFIG_PCI
+
+/*
+ *	Define the Stallion PCI vendor and device IDs.
+ */
+#ifndef	PCI_VENDOR_ID_STALLION
+#define	PCI_VENDOR_ID_STALLION		0x124d
+#endif
+#ifndef PCI_DEVICE_ID_ECHPCI832
+#define	PCI_DEVICE_ID_ECHPCI832		0x0000
+#endif
+#ifndef PCI_DEVICE_ID_ECHPCI864
+#define	PCI_DEVICE_ID_ECHPCI864		0x0002
+#endif
+#ifndef PCI_DEVICE_ID_EIOPCI
+#define	PCI_DEVICE_ID_EIOPCI		0x0003
+#endif
+
+/*
+ *	Define structure to hold all Stallion PCI boards.
+ */
+typedef struct stlpcibrd {
+	unsigned short		vendid;
+	unsigned short		devid;
+	int			brdtype;
+} stlpcibrd_t;
+
+static stlpcibrd_t	stl_pcibrds[] = {
+	{ PCI_VENDOR_ID_STALLION, PCI_DEVICE_ID_ECHPCI864, BRD_ECH64PCI },
+	{ PCI_VENDOR_ID_STALLION, PCI_DEVICE_ID_EIOPCI, BRD_EASYIOPCI },
+	{ PCI_VENDOR_ID_STALLION, PCI_DEVICE_ID_ECHPCI832, BRD_ECHPCI },
+	{ PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87410, BRD_ECHPCI },
+};
+
+static int	stl_nrpcibrds = sizeof(stl_pcibrds) / sizeof(stlpcibrd_t);
+
+#endif
+
+/*****************************************************************************/
+
+/*
+ *	Define macros to extract a brd/port number from a minor number.
+ */
+#define	MINOR2BRD(min)		(((min) & 0xc0) >> 6)
+#define	MINOR2PORT(min)		((min) & 0x3f)
+
+/*
+ *	Define a baud rate table that converts termios baud rate selector
+ *	into the actual baud rate value. All baud rate calculations are
+ *	based on the actual baud rate required.
+ */
+static unsigned int	stl_baudrates[] = {
+	0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800,
+	9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600
+};
+
+/*
+ *	Define some handy local macros...
+ */
+#undef	MIN
+#define	MIN(a,b)	(((a) <= (b)) ? (a) : (b))
+
+#undef	TOLOWER
+#define	TOLOWER(x)	((((x) >= 'A') && ((x) <= 'Z')) ? ((x) + 0x20) : (x))
+
+/*****************************************************************************/
+
+/*
+ *	Declare all those functions in this driver!
+ */
+
+static void	stl_argbrds(void);
+static int	stl_parsebrd(stlconf_t *confp, char **argp);
+
+static unsigned long stl_atol(char *str);
+
+int		stl_init(void);
+static int	stl_open(struct tty_struct *tty, struct file *filp);
+static void	stl_close(struct tty_struct *tty, struct file *filp);
+static int	stl_write(struct tty_struct *tty, const unsigned char *buf, int count);
+static void	stl_putchar(struct tty_struct *tty, unsigned char ch);
+static void	stl_flushchars(struct tty_struct *tty);
+static int	stl_writeroom(struct tty_struct *tty);
+static int	stl_charsinbuffer(struct tty_struct *tty);
+static int	stl_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg);
+static void	stl_settermios(struct tty_struct *tty, struct termios *old);
+static void	stl_throttle(struct tty_struct *tty);
+static void	stl_unthrottle(struct tty_struct *tty);
+static void	stl_stop(struct tty_struct *tty);
+static void	stl_start(struct tty_struct *tty);
+static void	stl_flushbuffer(struct tty_struct *tty);
+static void	stl_breakctl(struct tty_struct *tty, int state);
+static void	stl_waituntilsent(struct tty_struct *tty, int timeout);
+static void	stl_sendxchar(struct tty_struct *tty, char ch);
+static void	stl_hangup(struct tty_struct *tty);
+static int	stl_memioctl(struct inode *ip, struct file *fp, unsigned int cmd, unsigned long arg);
+static int	stl_portinfo(stlport_t *portp, int portnr, char *pos);
+static int	stl_readproc(char *page, char **start, off_t off, int count, int *eof, void *data);
+
+static int	stl_brdinit(stlbrd_t *brdp);
+static int	stl_initports(stlbrd_t *brdp, stlpanel_t *panelp);
+static int	stl_getserial(stlport_t *portp, struct serial_struct __user *sp);
+static int	stl_setserial(stlport_t *portp, struct serial_struct __user *sp);
+static int	stl_getbrdstats(combrd_t __user *bp);
+static int	stl_getportstats(stlport_t *portp, comstats_t __user *cp);
+static int	stl_clrportstats(stlport_t *portp, comstats_t __user *cp);
+static int	stl_getportstruct(stlport_t __user *arg);
+static int	stl_getbrdstruct(stlbrd_t __user *arg);
+static int	stl_waitcarrier(stlport_t *portp, struct file *filp);
+static int	stl_eiointr(stlbrd_t *brdp);
+static int	stl_echatintr(stlbrd_t *brdp);
+static int	stl_echmcaintr(stlbrd_t *brdp);
+static int	stl_echpciintr(stlbrd_t *brdp);
+static int	stl_echpci64intr(stlbrd_t *brdp);
+static void	stl_offintr(void *private);
+static void	*stl_memalloc(int len);
+static stlbrd_t *stl_allocbrd(void);
+static stlport_t *stl_getport(int brdnr, int panelnr, int portnr);
+
+static inline int	stl_initbrds(void);
+static inline int	stl_initeio(stlbrd_t *brdp);
+static inline int	stl_initech(stlbrd_t *brdp);
+static inline int	stl_getbrdnr(void);
+
+#ifdef	CONFIG_PCI
+static inline int	stl_findpcibrds(void);
+static inline int	stl_initpcibrd(int brdtype, struct pci_dev *devp);
+#endif
+
+/*
+ *	CD1400 uart specific handling functions.
+ */
+static void	stl_cd1400setreg(stlport_t *portp, int regnr, int value);
+static int	stl_cd1400getreg(stlport_t *portp, int regnr);
+static int	stl_cd1400updatereg(stlport_t *portp, int regnr, int value);
+static int	stl_cd1400panelinit(stlbrd_t *brdp, stlpanel_t *panelp);
+static void	stl_cd1400portinit(stlbrd_t *brdp, stlpanel_t *panelp, stlport_t *portp);
+static void	stl_cd1400setport(stlport_t *portp, struct termios *tiosp);
+static int	stl_cd1400getsignals(stlport_t *portp);
+static void	stl_cd1400setsignals(stlport_t *portp, int dtr, int rts);
+static void	stl_cd1400ccrwait(stlport_t *portp);
+static void	stl_cd1400enablerxtx(stlport_t *portp, int rx, int tx);
+static void	stl_cd1400startrxtx(stlport_t *portp, int rx, int tx);
+static void	stl_cd1400disableintrs(stlport_t *portp);
+static void	stl_cd1400sendbreak(stlport_t *portp, int len);
+static void	stl_cd1400flowctrl(stlport_t *portp, int state);
+static void	stl_cd1400sendflow(stlport_t *portp, int state);
+static void	stl_cd1400flush(stlport_t *portp);
+static int	stl_cd1400datastate(stlport_t *portp);
+static void	stl_cd1400eiointr(stlpanel_t *panelp, unsigned int iobase);
+static void	stl_cd1400echintr(stlpanel_t *panelp, unsigned int iobase);
+static void	stl_cd1400txisr(stlpanel_t *panelp, int ioaddr);
+static void	stl_cd1400rxisr(stlpanel_t *panelp, int ioaddr);
+static void	stl_cd1400mdmisr(stlpanel_t *panelp, int ioaddr);
+
+static inline int	stl_cd1400breakisr(stlport_t *portp, int ioaddr);
+
+/*
+ *	SC26198 uart specific handling functions.
+ */
+static void	stl_sc26198setreg(stlport_t *portp, int regnr, int value);
+static int	stl_sc26198getreg(stlport_t *portp, int regnr);
+static int	stl_sc26198updatereg(stlport_t *portp, int regnr, int value);
+static int	stl_sc26198getglobreg(stlport_t *portp, int regnr);
+static int	stl_sc26198panelinit(stlbrd_t *brdp, stlpanel_t *panelp);
+static void	stl_sc26198portinit(stlbrd_t *brdp, stlpanel_t *panelp, stlport_t *portp);
+static void	stl_sc26198setport(stlport_t *portp, struct termios *tiosp);
+static int	stl_sc26198getsignals(stlport_t *portp);
+static void	stl_sc26198setsignals(stlport_t *portp, int dtr, int rts);
+static void	stl_sc26198enablerxtx(stlport_t *portp, int rx, int tx);
+static void	stl_sc26198startrxtx(stlport_t *portp, int rx, int tx);
+static void	stl_sc26198disableintrs(stlport_t *portp);
+static void	stl_sc26198sendbreak(stlport_t *portp, int len);
+static void	stl_sc26198flowctrl(stlport_t *portp, int state);
+static void	stl_sc26198sendflow(stlport_t *portp, int state);
+static void	stl_sc26198flush(stlport_t *portp);
+static int	stl_sc26198datastate(stlport_t *portp);
+static void	stl_sc26198wait(stlport_t *portp);
+static void	stl_sc26198txunflow(stlport_t *portp, struct tty_struct *tty);
+static void	stl_sc26198intr(stlpanel_t *panelp, unsigned int iobase);
+static void	stl_sc26198txisr(stlport_t *port);
+static void	stl_sc26198rxisr(stlport_t *port, unsigned int iack);
+static void	stl_sc26198rxbadch(stlport_t *portp, unsigned char status, char ch);
+static void	stl_sc26198rxbadchars(stlport_t *portp);
+static void	stl_sc26198otherisr(stlport_t *port, unsigned int iack);
+
+/*****************************************************************************/
+
+/*
+ *	Generic UART support structure.
+ */
+typedef struct uart {
+	int	(*panelinit)(stlbrd_t *brdp, stlpanel_t *panelp);
+	void	(*portinit)(stlbrd_t *brdp, stlpanel_t *panelp, stlport_t *portp);
+	void	(*setport)(stlport_t *portp, struct termios *tiosp);
+	int	(*getsignals)(stlport_t *portp);
+	void	(*setsignals)(stlport_t *portp, int dtr, int rts);
+	void	(*enablerxtx)(stlport_t *portp, int rx, int tx);
+	void	(*startrxtx)(stlport_t *portp, int rx, int tx);
+	void	(*disableintrs)(stlport_t *portp);
+	void	(*sendbreak)(stlport_t *portp, int len);
+	void	(*flowctrl)(stlport_t *portp, int state);
+	void	(*sendflow)(stlport_t *portp, int state);
+	void	(*flush)(stlport_t *portp);
+	int	(*datastate)(stlport_t *portp);
+	void	(*intr)(stlpanel_t *panelp, unsigned int iobase);
+} uart_t;
+
+/*
+ *	Define some macros to make calling these functions nice and clean.
+ */
+#define	stl_panelinit		(* ((uart_t *) panelp->uartp)->panelinit)
+#define	stl_portinit		(* ((uart_t *) portp->uartp)->portinit)
+#define	stl_setport		(* ((uart_t *) portp->uartp)->setport)
+#define	stl_getsignals		(* ((uart_t *) portp->uartp)->getsignals)
+#define	stl_setsignals		(* ((uart_t *) portp->uartp)->setsignals)
+#define	stl_enablerxtx		(* ((uart_t *) portp->uartp)->enablerxtx)
+#define	stl_startrxtx		(* ((uart_t *) portp->uartp)->startrxtx)
+#define	stl_disableintrs	(* ((uart_t *) portp->uartp)->disableintrs)
+#define	stl_sendbreak		(* ((uart_t *) portp->uartp)->sendbreak)
+#define	stl_flowctrl		(* ((uart_t *) portp->uartp)->flowctrl)
+#define	stl_sendflow		(* ((uart_t *) portp->uartp)->sendflow)
+#define	stl_flush		(* ((uart_t *) portp->uartp)->flush)
+#define	stl_datastate		(* ((uart_t *) portp->uartp)->datastate)
+
+/*****************************************************************************/
+
+/*
+ *	CD1400 UART specific data initialization.
+ */
+static uart_t stl_cd1400uart = {
+	stl_cd1400panelinit,
+	stl_cd1400portinit,
+	stl_cd1400setport,
+	stl_cd1400getsignals,
+	stl_cd1400setsignals,
+	stl_cd1400enablerxtx,
+	stl_cd1400startrxtx,
+	stl_cd1400disableintrs,
+	stl_cd1400sendbreak,
+	stl_cd1400flowctrl,
+	stl_cd1400sendflow,
+	stl_cd1400flush,
+	stl_cd1400datastate,
+	stl_cd1400eiointr
+};
+
+/*
+ *	Define the offsets within the register bank of a cd1400 based panel.
+ *	These io address offsets are common to the EasyIO board as well.
+ */
+#define	EREG_ADDR	0
+#define	EREG_DATA	4
+#define	EREG_RXACK	5
+#define	EREG_TXACK	6
+#define	EREG_MDACK	7
+
+#define	EREG_BANKSIZE	8
+
+#define	CD1400_CLK	25000000
+#define	CD1400_CLK8M	20000000
+
+/*
+ *	Define the cd1400 baud rate clocks. These are used when calculating
+ *	what clock and divisor to use for the required baud rate. Also
+ *	define the maximum baud rate allowed, and the default base baud.
+ */
+static int	stl_cd1400clkdivs[] = {
+	CD1400_CLK0, CD1400_CLK1, CD1400_CLK2, CD1400_CLK3, CD1400_CLK4
+};
+
+/*****************************************************************************/
+
+/*
+ *	SC26198 UART specific data initization.
+ */
+static uart_t stl_sc26198uart = {
+	stl_sc26198panelinit,
+	stl_sc26198portinit,
+	stl_sc26198setport,
+	stl_sc26198getsignals,
+	stl_sc26198setsignals,
+	stl_sc26198enablerxtx,
+	stl_sc26198startrxtx,
+	stl_sc26198disableintrs,
+	stl_sc26198sendbreak,
+	stl_sc26198flowctrl,
+	stl_sc26198sendflow,
+	stl_sc26198flush,
+	stl_sc26198datastate,
+	stl_sc26198intr
+};
+
+/*
+ *	Define the offsets within the register bank of a sc26198 based panel.
+ */
+#define	XP_DATA		0
+#define	XP_ADDR		1
+#define	XP_MODID	2
+#define	XP_STATUS	2
+#define	XP_IACK		3
+
+#define	XP_BANKSIZE	4
+
+/*
+ *	Define the sc26198 baud rate table. Offsets within the table
+ *	represent the actual baud rate selector of sc26198 registers.
+ */
+static unsigned int	sc26198_baudtable[] = {
+	50, 75, 150, 200, 300, 450, 600, 900, 1200, 1800, 2400, 3600,
+	4800, 7200, 9600, 14400, 19200, 28800, 38400, 57600, 115200,
+	230400, 460800, 921600
+};
+
+#define	SC26198_NRBAUDS		(sizeof(sc26198_baudtable) / sizeof(unsigned int))
+
+/*****************************************************************************/
+
+/*
+ *	Define the driver info for a user level control device. Used mainly
+ *	to get at port stats - only not using the port device itself.
+ */
+static struct file_operations	stl_fsiomem = {
+	.owner		= THIS_MODULE,
+	.ioctl		= stl_memioctl,
+};
+
+/*****************************************************************************/
+
+static struct class_simple *stallion_class;
+
+/*
+ *	Loadable module initialization stuff.
+ */
+
+static int __init stallion_module_init(void)
+{
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("init_module()\n");
+#endif
+
+	save_flags(flags);
+	cli();
+	stl_init();
+	restore_flags(flags);
+
+	return(0);
+}
+
+/*****************************************************************************/
+
+static void __exit stallion_module_exit(void)
+{
+	stlbrd_t	*brdp;
+	stlpanel_t	*panelp;
+	stlport_t	*portp;
+	unsigned long	flags;
+	int		i, j, k;
+
+#ifdef DEBUG
+	printk("cleanup_module()\n");
+#endif
+
+	printk(KERN_INFO "Unloading %s: version %s\n", stl_drvtitle,
+		stl_drvversion);
+
+	save_flags(flags);
+	cli();
+
+/*
+ *	Free up all allocated resources used by the ports. This includes
+ *	memory and interrupts. As part of this process we will also do
+ *	a hangup on every open port - to try to flush out any processes
+ *	hanging onto ports.
+ */
+	i = tty_unregister_driver(stl_serial);
+	put_tty_driver(stl_serial);
+	if (i) {
+		printk("STALLION: failed to un-register tty driver, "
+			"errno=%d\n", -i);
+		restore_flags(flags);
+		return;
+	}
+	for (i = 0; i < 4; i++) {
+		devfs_remove("staliomem/%d", i);
+		class_simple_device_remove(MKDEV(STL_SIOMEMMAJOR, i));
+	}
+	devfs_remove("staliomem");
+	if ((i = unregister_chrdev(STL_SIOMEMMAJOR, "staliomem")))
+		printk("STALLION: failed to un-register serial memory device, "
+			"errno=%d\n", -i);
+	class_simple_destroy(stallion_class);
+
+	if (stl_tmpwritebuf != (char *) NULL)
+		kfree(stl_tmpwritebuf);
+
+	for (i = 0; (i < stl_nrbrds); i++) {
+		if ((brdp = stl_brds[i]) == (stlbrd_t *) NULL)
+			continue;
+
+		free_irq(brdp->irq, brdp);
+
+		for (j = 0; (j < STL_MAXPANELS); j++) {
+			panelp = brdp->panels[j];
+			if (panelp == (stlpanel_t *) NULL)
+				continue;
+			for (k = 0; (k < STL_PORTSPERPANEL); k++) {
+				portp = panelp->ports[k];
+				if (portp == (stlport_t *) NULL)
+					continue;
+				if (portp->tty != (struct tty_struct *) NULL)
+					stl_hangup(portp->tty);
+				if (portp->tx.buf != (char *) NULL)
+					kfree(portp->tx.buf);
+				kfree(portp);
+			}
+			kfree(panelp);
+		}
+
+		release_region(brdp->ioaddr1, brdp->iosize1);
+		if (brdp->iosize2 > 0)
+			release_region(brdp->ioaddr2, brdp->iosize2);
+
+		kfree(brdp);
+		stl_brds[i] = (stlbrd_t *) NULL;
+	}
+
+	restore_flags(flags);
+}
+
+module_init(stallion_module_init);
+module_exit(stallion_module_exit);
+
+/*****************************************************************************/
+
+/*
+ *	Check for any arguments passed in on the module load command line.
+ */
+
+static void stl_argbrds(void)
+{
+	stlconf_t	conf;
+	stlbrd_t	*brdp;
+	int		i;
+
+#ifdef DEBUG
+	printk("stl_argbrds()\n");
+#endif
+
+	for (i = stl_nrbrds; (i < stl_nargs); i++) {
+		memset(&conf, 0, sizeof(conf));
+		if (stl_parsebrd(&conf, stl_brdsp[i]) == 0)
+			continue;
+		if ((brdp = stl_allocbrd()) == (stlbrd_t *) NULL)
+			continue;
+		stl_nrbrds = i + 1;
+		brdp->brdnr = i;
+		brdp->brdtype = conf.brdtype;
+		brdp->ioaddr1 = conf.ioaddr1;
+		brdp->ioaddr2 = conf.ioaddr2;
+		brdp->irq = conf.irq;
+		brdp->irqtype = conf.irqtype;
+		stl_brdinit(brdp);
+	}
+}
+
+/*****************************************************************************/
+
+/*
+ *	Convert an ascii string number into an unsigned long.
+ */
+
+static unsigned long stl_atol(char *str)
+{
+	unsigned long	val;
+	int		base, c;
+	char		*sp;
+
+	val = 0;
+	sp = str;
+	if ((*sp == '0') && (*(sp+1) == 'x')) {
+		base = 16;
+		sp += 2;
+	} else if (*sp == '0') {
+		base = 8;
+		sp++;
+	} else {
+		base = 10;
+	}
+
+	for (; (*sp != 0); sp++) {
+		c = (*sp > '9') ? (TOLOWER(*sp) - 'a' + 10) : (*sp - '0');
+		if ((c < 0) || (c >= base)) {
+			printk("STALLION: invalid argument %s\n", str);
+			val = 0;
+			break;
+		}
+		val = (val * base) + c;
+	}
+	return(val);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Parse the supplied argument string, into the board conf struct.
+ */
+
+static int stl_parsebrd(stlconf_t *confp, char **argp)
+{
+	char	*sp;
+	int	nrbrdnames, i;
+
+#ifdef DEBUG
+	printk("stl_parsebrd(confp=%x,argp=%x)\n", (int) confp, (int) argp);
+#endif
+
+	if ((argp[0] == (char *) NULL) || (*argp[0] == 0))
+		return(0);
+
+	for (sp = argp[0], i = 0; ((*sp != 0) && (i < 25)); sp++, i++)
+		*sp = TOLOWER(*sp);
+
+	nrbrdnames = sizeof(stl_brdstr) / sizeof(stlbrdtype_t);
+	for (i = 0; (i < nrbrdnames); i++) {
+		if (strcmp(stl_brdstr[i].name, argp[0]) == 0)
+			break;
+	}
+	if (i >= nrbrdnames) {
+		printk("STALLION: unknown board name, %s?\n", argp[0]);
+		return(0);
+	}
+
+	confp->brdtype = stl_brdstr[i].type;
+
+	i = 1;
+	if ((argp[i] != (char *) NULL) && (*argp[i] != 0))
+		confp->ioaddr1 = stl_atol(argp[i]);
+	i++;
+	if (confp->brdtype == BRD_ECH) {
+		if ((argp[i] != (char *) NULL) && (*argp[i] != 0))
+			confp->ioaddr2 = stl_atol(argp[i]);
+		i++;
+	}
+	if ((argp[i] != (char *) NULL) && (*argp[i] != 0))
+		confp->irq = stl_atol(argp[i]);
+	return(1);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Local driver kernel memory allocation routine.
+ */
+
+static void *stl_memalloc(int len)
+{
+	return((void *) kmalloc(len, GFP_KERNEL));
+}
+
+/*****************************************************************************/
+
+/*
+ *	Allocate a new board structure. Fill out the basic info in it.
+ */
+
+static stlbrd_t *stl_allocbrd(void)
+{
+	stlbrd_t	*brdp;
+
+	brdp = (stlbrd_t *) stl_memalloc(sizeof(stlbrd_t));
+	if (brdp == (stlbrd_t *) NULL) {
+		printk("STALLION: failed to allocate memory (size=%d)\n",
+			sizeof(stlbrd_t));
+		return((stlbrd_t *) NULL);
+	}
+
+	memset(brdp, 0, sizeof(stlbrd_t));
+	brdp->magic = STL_BOARDMAGIC;
+	return(brdp);
+}
+
+/*****************************************************************************/
+
+static int stl_open(struct tty_struct *tty, struct file *filp)
+{
+	stlport_t	*portp;
+	stlbrd_t	*brdp;
+	unsigned int	minordev;
+	int		brdnr, panelnr, portnr, rc;
+
+#ifdef DEBUG
+	printk("stl_open(tty=%x,filp=%x): device=%s\n", (int) tty,
+		(int) filp, tty->name);
+#endif
+
+	minordev = tty->index;
+	brdnr = MINOR2BRD(minordev);
+	if (brdnr >= stl_nrbrds)
+		return(-ENODEV);
+	brdp = stl_brds[brdnr];
+	if (brdp == (stlbrd_t *) NULL)
+		return(-ENODEV);
+	minordev = MINOR2PORT(minordev);
+	for (portnr = -1, panelnr = 0; (panelnr < STL_MAXPANELS); panelnr++) {
+		if (brdp->panels[panelnr] == (stlpanel_t *) NULL)
+			break;
+		if (minordev < brdp->panels[panelnr]->nrports) {
+			portnr = minordev;
+			break;
+		}
+		minordev -= brdp->panels[panelnr]->nrports;
+	}
+	if (portnr < 0)
+		return(-ENODEV);
+
+	portp = brdp->panels[panelnr]->ports[portnr];
+	if (portp == (stlport_t *) NULL)
+		return(-ENODEV);
+
+/*
+ *	On the first open of the device setup the port hardware, and
+ *	initialize the per port data structure.
+ */
+	portp->tty = tty;
+	tty->driver_data = portp;
+	portp->refcount++;
+
+	if ((portp->flags & ASYNC_INITIALIZED) == 0) {
+		if (portp->tx.buf == (char *) NULL) {
+			portp->tx.buf = (char *) stl_memalloc(STL_TXBUFSIZE);
+			if (portp->tx.buf == (char *) NULL)
+				return(-ENOMEM);
+			portp->tx.head = portp->tx.buf;
+			portp->tx.tail = portp->tx.buf;
+		}
+		stl_setport(portp, tty->termios);
+		portp->sigs = stl_getsignals(portp);
+		stl_setsignals(portp, 1, 1);
+		stl_enablerxtx(portp, 1, 1);
+		stl_startrxtx(portp, 1, 0);
+		clear_bit(TTY_IO_ERROR, &tty->flags);
+		portp->flags |= ASYNC_INITIALIZED;
+	}
+
+/*
+ *	Check if this port is in the middle of closing. If so then wait
+ *	until it is closed then return error status, based on flag settings.
+ *	The sleep here does not need interrupt protection since the wakeup
+ *	for it is done with the same context.
+ */
+	if (portp->flags & ASYNC_CLOSING) {
+		interruptible_sleep_on(&portp->close_wait);
+		if (portp->flags & ASYNC_HUP_NOTIFY)
+			return(-EAGAIN);
+		return(-ERESTARTSYS);
+	}
+
+/*
+ *	Based on type of open being done check if it can overlap with any
+ *	previous opens still in effect. If we are a normal serial device
+ *	then also we might have to wait for carrier.
+ */
+	if (!(filp->f_flags & O_NONBLOCK)) {
+		if ((rc = stl_waitcarrier(portp, filp)) != 0)
+			return(rc);
+	}
+	portp->flags |= ASYNC_NORMAL_ACTIVE;
+
+	return(0);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Possibly need to wait for carrier (DCD signal) to come high. Say
+ *	maybe because if we are clocal then we don't need to wait...
+ */
+
+static int stl_waitcarrier(stlport_t *portp, struct file *filp)
+{
+	unsigned long	flags;
+	int		rc, doclocal;
+
+#ifdef DEBUG
+	printk("stl_waitcarrier(portp=%x,filp=%x)\n", (int) portp, (int) filp);
+#endif
+
+	rc = 0;
+	doclocal = 0;
+
+	if (portp->tty->termios->c_cflag & CLOCAL)
+		doclocal++;
+
+	save_flags(flags);
+	cli();
+	portp->openwaitcnt++;
+	if (! tty_hung_up_p(filp))
+		portp->refcount--;
+
+	for (;;) {
+		stl_setsignals(portp, 1, 1);
+		if (tty_hung_up_p(filp) ||
+		    ((portp->flags & ASYNC_INITIALIZED) == 0)) {
+			if (portp->flags & ASYNC_HUP_NOTIFY)
+				rc = -EBUSY;
+			else
+				rc = -ERESTARTSYS;
+			break;
+		}
+		if (((portp->flags & ASYNC_CLOSING) == 0) &&
+		    (doclocal || (portp->sigs & TIOCM_CD))) {
+			break;
+		}
+		if (signal_pending(current)) {
+			rc = -ERESTARTSYS;
+			break;
+		}
+		interruptible_sleep_on(&portp->open_wait);
+	}
+
+	if (! tty_hung_up_p(filp))
+		portp->refcount++;
+	portp->openwaitcnt--;
+	restore_flags(flags);
+
+	return(rc);
+}
+
+/*****************************************************************************/
+
+static void stl_close(struct tty_struct *tty, struct file *filp)
+{
+	stlport_t	*portp;
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_close(tty=%x,filp=%x)\n", (int) tty, (int) filp);
+#endif
+
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+
+	save_flags(flags);
+	cli();
+	if (tty_hung_up_p(filp)) {
+		restore_flags(flags);
+		return;
+	}
+	if ((tty->count == 1) && (portp->refcount != 1))
+		portp->refcount = 1;
+	if (portp->refcount-- > 1) {
+		restore_flags(flags);
+		return;
+	}
+
+	portp->refcount = 0;
+	portp->flags |= ASYNC_CLOSING;
+
+/*
+ *	May want to wait for any data to drain before closing. The BUSY
+ *	flag keeps track of whether we are still sending or not - it is
+ *	very accurate for the cd1400, not quite so for the sc26198.
+ *	(The sc26198 has no "end-of-data" interrupt only empty FIFO)
+ */
+	tty->closing = 1;
+	if (portp->closing_wait != ASYNC_CLOSING_WAIT_NONE)
+		tty_wait_until_sent(tty, portp->closing_wait);
+	stl_waituntilsent(tty, (HZ / 2));
+
+	portp->flags &= ~ASYNC_INITIALIZED;
+	stl_disableintrs(portp);
+	if (tty->termios->c_cflag & HUPCL)
+		stl_setsignals(portp, 0, 0);
+	stl_enablerxtx(portp, 0, 0);
+	stl_flushbuffer(tty);
+	portp->istate = 0;
+	if (portp->tx.buf != (char *) NULL) {
+		kfree(portp->tx.buf);
+		portp->tx.buf = (char *) NULL;
+		portp->tx.head = (char *) NULL;
+		portp->tx.tail = (char *) NULL;
+	}
+	set_bit(TTY_IO_ERROR, &tty->flags);
+	tty_ldisc_flush(tty);
+
+	tty->closing = 0;
+	portp->tty = (struct tty_struct *) NULL;
+
+	if (portp->openwaitcnt) {
+		if (portp->close_delay)
+			msleep_interruptible(jiffies_to_msecs(portp->close_delay));
+		wake_up_interruptible(&portp->open_wait);
+	}
+
+	portp->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
+	wake_up_interruptible(&portp->close_wait);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Write routine. Take data and stuff it in to the TX ring queue.
+ *	If transmit interrupts are not running then start them.
+ */
+
+static int stl_write(struct tty_struct *tty, const unsigned char *buf, int count)
+{
+	stlport_t	*portp;
+	unsigned int	len, stlen;
+	unsigned char	*chbuf;
+	char		*head, *tail;
+
+#ifdef DEBUG
+	printk("stl_write(tty=%x,buf=%x,count=%d)\n",
+		(int) tty, (int) buf, count);
+#endif
+
+	if ((tty == (struct tty_struct *) NULL) ||
+	    (stl_tmpwritebuf == (char *) NULL))
+		return(0);
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return(0);
+	if (portp->tx.buf == (char *) NULL)
+		return(0);
+
+/*
+ *	If copying direct from user space we must cater for page faults,
+ *	causing us to "sleep" here for a while. To handle this copy in all
+ *	the data we need now, into a local buffer. Then when we got it all
+ *	copy it into the TX buffer.
+ */
+	chbuf = (unsigned char *) buf;
+
+	head = portp->tx.head;
+	tail = portp->tx.tail;
+	if (head >= tail) {
+		len = STL_TXBUFSIZE - (head - tail) - 1;
+		stlen = STL_TXBUFSIZE - (head - portp->tx.buf);
+	} else {
+		len = tail - head - 1;
+		stlen = len;
+	}
+
+	len = MIN(len, count);
+	count = 0;
+	while (len > 0) {
+		stlen = MIN(len, stlen);
+		memcpy(head, chbuf, stlen);
+		len -= stlen;
+		chbuf += stlen;
+		count += stlen;
+		head += stlen;
+		if (head >= (portp->tx.buf + STL_TXBUFSIZE)) {
+			head = portp->tx.buf;
+			stlen = tail - head;
+		}
+	}
+	portp->tx.head = head;
+
+	clear_bit(ASYI_TXLOW, &portp->istate);
+	stl_startrxtx(portp, -1, 1);
+
+	return(count);
+}
+
+/*****************************************************************************/
+
+static void stl_putchar(struct tty_struct *tty, unsigned char ch)
+{
+	stlport_t	*portp;
+	unsigned int	len;
+	char		*head, *tail;
+
+#ifdef DEBUG
+	printk("stl_putchar(tty=%x,ch=%x)\n", (int) tty, (int) ch);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+	if (portp->tx.buf == (char *) NULL)
+		return;
+
+	head = portp->tx.head;
+	tail = portp->tx.tail;
+
+	len = (head >= tail) ? (STL_TXBUFSIZE - (head - tail)) : (tail - head);
+	len--;
+
+	if (len > 0) {
+		*head++ = ch;
+		if (head >= (portp->tx.buf + STL_TXBUFSIZE))
+			head = portp->tx.buf;
+	}	
+	portp->tx.head = head;
+}
+
+/*****************************************************************************/
+
+/*
+ *	If there are any characters in the buffer then make sure that TX
+ *	interrupts are on and get'em out. Normally used after the putchar
+ *	routine has been called.
+ */
+
+static void stl_flushchars(struct tty_struct *tty)
+{
+	stlport_t	*portp;
+
+#ifdef DEBUG
+	printk("stl_flushchars(tty=%x)\n", (int) tty);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+	if (portp->tx.buf == (char *) NULL)
+		return;
+
+#if 0
+	if (tty->stopped || tty->hw_stopped ||
+	    (portp->tx.head == portp->tx.tail))
+		return;
+#endif
+	stl_startrxtx(portp, -1, 1);
+}
+
+/*****************************************************************************/
+
+static int stl_writeroom(struct tty_struct *tty)
+{
+	stlport_t	*portp;
+	char		*head, *tail;
+
+#ifdef DEBUG
+	printk("stl_writeroom(tty=%x)\n", (int) tty);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return(0);
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return(0);
+	if (portp->tx.buf == (char *) NULL)
+		return(0);
+
+	head = portp->tx.head;
+	tail = portp->tx.tail;
+	return((head >= tail) ? (STL_TXBUFSIZE - (head - tail) - 1) : (tail - head - 1));
+}
+
+/*****************************************************************************/
+
+/*
+ *	Return number of chars in the TX buffer. Normally we would just
+ *	calculate the number of chars in the buffer and return that, but if
+ *	the buffer is empty and TX interrupts are still on then we return
+ *	that the buffer still has 1 char in it. This way whoever called us
+ *	will not think that ALL chars have drained - since the UART still
+ *	must have some chars in it (we are busy after all).
+ */
+
+static int stl_charsinbuffer(struct tty_struct *tty)
+{
+	stlport_t	*portp;
+	unsigned int	size;
+	char		*head, *tail;
+
+#ifdef DEBUG
+	printk("stl_charsinbuffer(tty=%x)\n", (int) tty);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return(0);
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return(0);
+	if (portp->tx.buf == (char *) NULL)
+		return(0);
+
+	head = portp->tx.head;
+	tail = portp->tx.tail;
+	size = (head >= tail) ? (head - tail) : (STL_TXBUFSIZE - (tail - head));
+	if ((size == 0) && test_bit(ASYI_TXBUSY, &portp->istate))
+		size = 1;
+	return(size);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Generate the serial struct info.
+ */
+
+static int stl_getserial(stlport_t *portp, struct serial_struct __user *sp)
+{
+	struct serial_struct	sio;
+	stlbrd_t		*brdp;
+
+#ifdef DEBUG
+	printk("stl_getserial(portp=%x,sp=%x)\n", (int) portp, (int) sp);
+#endif
+
+	memset(&sio, 0, sizeof(struct serial_struct));
+	sio.line = portp->portnr;
+	sio.port = portp->ioaddr;
+	sio.flags = portp->flags;
+	sio.baud_base = portp->baud_base;
+	sio.close_delay = portp->close_delay;
+	sio.closing_wait = portp->closing_wait;
+	sio.custom_divisor = portp->custom_divisor;
+	sio.hub6 = 0;
+	if (portp->uartp == &stl_cd1400uart) {
+		sio.type = PORT_CIRRUS;
+		sio.xmit_fifo_size = CD1400_TXFIFOSIZE;
+	} else {
+		sio.type = PORT_UNKNOWN;
+		sio.xmit_fifo_size = SC26198_TXFIFOSIZE;
+	}
+
+	brdp = stl_brds[portp->brdnr];
+	if (brdp != (stlbrd_t *) NULL)
+		sio.irq = brdp->irq;
+
+	return copy_to_user(sp, &sio, sizeof(struct serial_struct)) ? -EFAULT : 0;
+}
+
+/*****************************************************************************/
+
+/*
+ *	Set port according to the serial struct info.
+ *	At this point we do not do any auto-configure stuff, so we will
+ *	just quietly ignore any requests to change irq, etc.
+ */
+
+static int stl_setserial(stlport_t *portp, struct serial_struct __user *sp)
+{
+	struct serial_struct	sio;
+
+#ifdef DEBUG
+	printk("stl_setserial(portp=%x,sp=%x)\n", (int) portp, (int) sp);
+#endif
+
+	if (copy_from_user(&sio, sp, sizeof(struct serial_struct)))
+		return -EFAULT;
+	if (!capable(CAP_SYS_ADMIN)) {
+		if ((sio.baud_base != portp->baud_base) ||
+		    (sio.close_delay != portp->close_delay) ||
+		    ((sio.flags & ~ASYNC_USR_MASK) !=
+		    (portp->flags & ~ASYNC_USR_MASK)))
+			return(-EPERM);
+	} 
+
+	portp->flags = (portp->flags & ~ASYNC_USR_MASK) |
+		(sio.flags & ASYNC_USR_MASK);
+	portp->baud_base = sio.baud_base;
+	portp->close_delay = sio.close_delay;
+	portp->closing_wait = sio.closing_wait;
+	portp->custom_divisor = sio.custom_divisor;
+	stl_setport(portp, portp->tty->termios);
+	return(0);
+}
+
+/*****************************************************************************/
+
+static int stl_tiocmget(struct tty_struct *tty, struct file *file)
+{
+	stlport_t	*portp;
+
+	if (tty == (struct tty_struct *) NULL)
+		return(-ENODEV);
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return(-ENODEV);
+	if (tty->flags & (1 << TTY_IO_ERROR))
+		return(-EIO);
+
+	return stl_getsignals(portp);
+}
+
+static int stl_tiocmset(struct tty_struct *tty, struct file *file,
+			unsigned int set, unsigned int clear)
+{
+	stlport_t	*portp;
+	int rts = -1, dtr = -1;
+
+	if (tty == (struct tty_struct *) NULL)
+		return(-ENODEV);
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return(-ENODEV);
+	if (tty->flags & (1 << TTY_IO_ERROR))
+		return(-EIO);
+
+	if (set & TIOCM_RTS)
+		rts = 1;
+	if (set & TIOCM_DTR)
+		dtr = 1;
+	if (clear & TIOCM_RTS)
+		rts = 0;
+	if (clear & TIOCM_DTR)
+		dtr = 0;
+
+	stl_setsignals(portp, dtr, rts);
+	return 0;
+}
+
+static int stl_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg)
+{
+	stlport_t	*portp;
+	unsigned int	ival;
+	int		rc;
+	void __user *argp = (void __user *)arg;
+
+#ifdef DEBUG
+	printk("stl_ioctl(tty=%x,file=%x,cmd=%x,arg=%x)\n",
+		(int) tty, (int) file, cmd, (int) arg);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return(-ENODEV);
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return(-ENODEV);
+
+	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
+ 	    (cmd != COM_GETPORTSTATS) && (cmd != COM_CLRPORTSTATS)) {
+		if (tty->flags & (1 << TTY_IO_ERROR))
+			return(-EIO);
+	}
+
+	rc = 0;
+
+	switch (cmd) {
+	case TIOCGSOFTCAR:
+		rc = put_user(((tty->termios->c_cflag & CLOCAL) ? 1 : 0),
+			(unsigned __user *) argp);
+		break;
+	case TIOCSSOFTCAR:
+		if (get_user(ival, (unsigned int __user *) arg))
+			return -EFAULT;
+		tty->termios->c_cflag =
+				(tty->termios->c_cflag & ~CLOCAL) |
+				(ival ? CLOCAL : 0);
+		break;
+	case TIOCGSERIAL:
+		rc = stl_getserial(portp, argp);
+		break;
+	case TIOCSSERIAL:
+		rc = stl_setserial(portp, argp);
+		break;
+	case COM_GETPORTSTATS:
+		rc = stl_getportstats(portp, argp);
+		break;
+	case COM_CLRPORTSTATS:
+		rc = stl_clrportstats(portp, argp);
+		break;
+	case TIOCSERCONFIG:
+	case TIOCSERGWILD:
+	case TIOCSERSWILD:
+	case TIOCSERGETLSR:
+	case TIOCSERGSTRUCT:
+	case TIOCSERGETMULTI:
+	case TIOCSERSETMULTI:
+	default:
+		rc = -ENOIOCTLCMD;
+		break;
+	}
+
+	return(rc);
+}
+
+/*****************************************************************************/
+
+static void stl_settermios(struct tty_struct *tty, struct termios *old)
+{
+	stlport_t	*portp;
+	struct termios	*tiosp;
+
+#ifdef DEBUG
+	printk("stl_settermios(tty=%x,old=%x)\n", (int) tty, (int) old);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+
+	tiosp = tty->termios;
+	if ((tiosp->c_cflag == old->c_cflag) &&
+	    (tiosp->c_iflag == old->c_iflag))
+		return;
+
+	stl_setport(portp, tiosp);
+	stl_setsignals(portp, ((tiosp->c_cflag & (CBAUD & ~CBAUDEX)) ? 1 : 0),
+		-1);
+	if ((old->c_cflag & CRTSCTS) && ((tiosp->c_cflag & CRTSCTS) == 0)) {
+		tty->hw_stopped = 0;
+		stl_start(tty);
+	}
+	if (((old->c_cflag & CLOCAL) == 0) && (tiosp->c_cflag & CLOCAL))
+		wake_up_interruptible(&portp->open_wait);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Attempt to flow control who ever is sending us data. Based on termios
+ *	settings use software or/and hardware flow control.
+ */
+
+static void stl_throttle(struct tty_struct *tty)
+{
+	stlport_t	*portp;
+
+#ifdef DEBUG
+	printk("stl_throttle(tty=%x)\n", (int) tty);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+	stl_flowctrl(portp, 0);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Unflow control the device sending us data...
+ */
+
+static void stl_unthrottle(struct tty_struct *tty)
+{
+	stlport_t	*portp;
+
+#ifdef DEBUG
+	printk("stl_unthrottle(tty=%x)\n", (int) tty);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+	stl_flowctrl(portp, 1);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Stop the transmitter. Basically to do this we will just turn TX
+ *	interrupts off.
+ */
+
+static void stl_stop(struct tty_struct *tty)
+{
+	stlport_t	*portp;
+
+#ifdef DEBUG
+	printk("stl_stop(tty=%x)\n", (int) tty);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+	stl_startrxtx(portp, -1, 0);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Start the transmitter again. Just turn TX interrupts back on.
+ */
+
+static void stl_start(struct tty_struct *tty)
+{
+	stlport_t	*portp;
+
+#ifdef DEBUG
+	printk("stl_start(tty=%x)\n", (int) tty);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+	stl_startrxtx(portp, -1, 1);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Hangup this port. This is pretty much like closing the port, only
+ *	a little more brutal. No waiting for data to drain. Shutdown the
+ *	port and maybe drop signals.
+ */
+
+static void stl_hangup(struct tty_struct *tty)
+{
+	stlport_t	*portp;
+
+#ifdef DEBUG
+	printk("stl_hangup(tty=%x)\n", (int) tty);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+
+	portp->flags &= ~ASYNC_INITIALIZED;
+	stl_disableintrs(portp);
+	if (tty->termios->c_cflag & HUPCL)
+		stl_setsignals(portp, 0, 0);
+	stl_enablerxtx(portp, 0, 0);
+	stl_flushbuffer(tty);
+	portp->istate = 0;
+	set_bit(TTY_IO_ERROR, &tty->flags);
+	if (portp->tx.buf != (char *) NULL) {
+		kfree(portp->tx.buf);
+		portp->tx.buf = (char *) NULL;
+		portp->tx.head = (char *) NULL;
+		portp->tx.tail = (char *) NULL;
+	}
+	portp->tty = (struct tty_struct *) NULL;
+	portp->flags &= ~ASYNC_NORMAL_ACTIVE;
+	portp->refcount = 0;
+	wake_up_interruptible(&portp->open_wait);
+}
+
+/*****************************************************************************/
+
+static void stl_flushbuffer(struct tty_struct *tty)
+{
+	stlport_t	*portp;
+
+#ifdef DEBUG
+	printk("stl_flushbuffer(tty=%x)\n", (int) tty);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+
+	stl_flush(portp);
+	tty_wakeup(tty);
+}
+
+/*****************************************************************************/
+
+static void stl_breakctl(struct tty_struct *tty, int state)
+{
+	stlport_t	*portp;
+
+#ifdef DEBUG
+	printk("stl_breakctl(tty=%x,state=%d)\n", (int) tty, state);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+
+	stl_sendbreak(portp, ((state == -1) ? 1 : 2));
+}
+
+/*****************************************************************************/
+
+static void stl_waituntilsent(struct tty_struct *tty, int timeout)
+{
+	stlport_t	*portp;
+	unsigned long	tend;
+
+#ifdef DEBUG
+	printk("stl_waituntilsent(tty=%x,timeout=%d)\n", (int) tty, timeout);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+
+	if (timeout == 0)
+		timeout = HZ;
+	tend = jiffies + timeout;
+
+	while (stl_datastate(portp)) {
+		if (signal_pending(current))
+			break;
+		msleep_interruptible(20);
+		if (time_after_eq(jiffies, tend))
+			break;
+	}
+}
+
+/*****************************************************************************/
+
+static void stl_sendxchar(struct tty_struct *tty, char ch)
+{
+	stlport_t	*portp;
+
+#ifdef DEBUG
+	printk("stl_sendxchar(tty=%x,ch=%x)\n", (int) tty, ch);
+#endif
+
+	if (tty == (struct tty_struct *) NULL)
+		return;
+	portp = tty->driver_data;
+	if (portp == (stlport_t *) NULL)
+		return;
+
+	if (ch == STOP_CHAR(tty))
+		stl_sendflow(portp, 0);
+	else if (ch == START_CHAR(tty))
+		stl_sendflow(portp, 1);
+	else
+		stl_putchar(tty, ch);
+}
+
+/*****************************************************************************/
+
+#define	MAXLINE		80
+
+/*
+ *	Format info for a specified port. The line is deliberately limited
+ *	to 80 characters. (If it is too long it will be truncated, if too
+ *	short then padded with spaces).
+ */
+
+static int stl_portinfo(stlport_t *portp, int portnr, char *pos)
+{
+	char	*sp;
+	int	sigs, cnt;
+
+	sp = pos;
+	sp += sprintf(sp, "%d: uart:%s tx:%d rx:%d",
+		portnr, (portp->hwid == 1) ? "SC26198" : "CD1400",
+		(int) portp->stats.txtotal, (int) portp->stats.rxtotal);
+
+	if (portp->stats.rxframing)
+		sp += sprintf(sp, " fe:%d", (int) portp->stats.rxframing);
+	if (portp->stats.rxparity)
+		sp += sprintf(sp, " pe:%d", (int) portp->stats.rxparity);
+	if (portp->stats.rxbreaks)
+		sp += sprintf(sp, " brk:%d", (int) portp->stats.rxbreaks);
+	if (portp->stats.rxoverrun)
+		sp += sprintf(sp, " oe:%d", (int) portp->stats.rxoverrun);
+
+	sigs = stl_getsignals(portp);
+	cnt = sprintf(sp, "%s%s%s%s%s ",
+		(sigs & TIOCM_RTS) ? "|RTS" : "",
+		(sigs & TIOCM_CTS) ? "|CTS" : "",
+		(sigs & TIOCM_DTR) ? "|DTR" : "",
+		(sigs & TIOCM_CD) ? "|DCD" : "",
+		(sigs & TIOCM_DSR) ? "|DSR" : "");
+	*sp = ' ';
+	sp += cnt;
+
+	for (cnt = (sp - pos); (cnt < (MAXLINE - 1)); cnt++)
+		*sp++ = ' ';
+	if (cnt >= MAXLINE)
+		pos[(MAXLINE - 2)] = '+';
+	pos[(MAXLINE - 1)] = '\n';
+
+	return(MAXLINE);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Port info, read from the /proc file system.
+ */
+
+static int stl_readproc(char *page, char **start, off_t off, int count, int *eof, void *data)
+{
+	stlbrd_t	*brdp;
+	stlpanel_t	*panelp;
+	stlport_t	*portp;
+	int		brdnr, panelnr, portnr, totalport;
+	int		curoff, maxoff;
+	char		*pos;
+
+#ifdef DEBUG
+	printk("stl_readproc(page=%x,start=%x,off=%x,count=%d,eof=%x,"
+		"data=%x\n", (int) page, (int) start, (int) off, count,
+		(int) eof, (int) data);
+#endif
+
+	pos = page;
+	totalport = 0;
+	curoff = 0;
+
+	if (off == 0) {
+		pos += sprintf(pos, "%s: version %s", stl_drvtitle,
+			stl_drvversion);
+		while (pos < (page + MAXLINE - 1))
+			*pos++ = ' ';
+		*pos++ = '\n';
+	}
+	curoff =  MAXLINE;
+
+/*
+ *	We scan through for each board, panel and port. The offset is
+ *	calculated on the fly, and irrelevant ports are skipped.
+ */
+	for (brdnr = 0; (brdnr < stl_nrbrds); brdnr++) {
+		brdp = stl_brds[brdnr];
+		if (brdp == (stlbrd_t *) NULL)
+			continue;
+		if (brdp->state == 0)
+			continue;
+
+		maxoff = curoff + (brdp->nrports * MAXLINE);
+		if (off >= maxoff) {
+			curoff = maxoff;
+			continue;
+		}
+
+		totalport = brdnr * STL_MAXPORTS;
+		for (panelnr = 0; (panelnr < brdp->nrpanels); panelnr++) {
+			panelp = brdp->panels[panelnr];
+			if (panelp == (stlpanel_t *) NULL)
+				continue;
+
+			maxoff = curoff + (panelp->nrports * MAXLINE);
+			if (off >= maxoff) {
+				curoff = maxoff;
+				totalport += panelp->nrports;
+				continue;
+			}
+
+			for (portnr = 0; (portnr < panelp->nrports); portnr++,
+			    totalport++) {
+				portp = panelp->ports[portnr];
+				if (portp == (stlport_t *) NULL)
+					continue;
+				if (off >= (curoff += MAXLINE))
+					continue;
+				if ((pos - page + MAXLINE) > count)
+					goto stl_readdone;
+				pos += stl_portinfo(portp, totalport, pos);
+			}
+		}
+	}
+
+	*eof = 1;
+
+stl_readdone:
+	*start = page;
+	return(pos - page);
+}
+
+/*****************************************************************************/
+
+/*
+ *	All board interrupts are vectored through here first. This code then
+ *	calls off to the approrpriate board interrupt handlers.
+ */
+
+static irqreturn_t stl_intr(int irq, void *dev_id, struct pt_regs *regs)
+{
+	stlbrd_t	*brdp = (stlbrd_t *) dev_id;
+
+#ifdef DEBUG
+	printk("stl_intr(brdp=%x,irq=%d,regs=%x)\n", (int) brdp, irq,
+	    (int) regs);
+#endif
+
+	return IRQ_RETVAL((* brdp->isr)(brdp));
+}
+
+/*****************************************************************************/
+
+/*
+ *	Interrupt service routine for EasyIO board types.
+ */
+
+static int stl_eiointr(stlbrd_t *brdp)
+{
+	stlpanel_t	*panelp;
+	unsigned int	iobase;
+	int		handled = 0;
+
+	panelp = brdp->panels[0];
+	iobase = panelp->iobase;
+	while (inb(brdp->iostatus) & EIO_INTRPEND) {
+		handled = 1;
+		(* panelp->isr)(panelp, iobase);
+	}
+	return handled;
+}
+
+/*****************************************************************************/
+
+/*
+ *	Interrupt service routine for ECH-AT board types.
+ */
+
+static int stl_echatintr(stlbrd_t *brdp)
+{
+	stlpanel_t	*panelp;
+	unsigned int	ioaddr;
+	int		bnknr;
+	int		handled = 0;
+
+	outb((brdp->ioctrlval | ECH_BRDENABLE), brdp->ioctrl);
+
+	while (inb(brdp->iostatus) & ECH_INTRPEND) {
+		handled = 1;
+		for (bnknr = 0; (bnknr < brdp->nrbnks); bnknr++) {
+			ioaddr = brdp->bnkstataddr[bnknr];
+			if (inb(ioaddr) & ECH_PNLINTRPEND) {
+				panelp = brdp->bnk2panel[bnknr];
+				(* panelp->isr)(panelp, (ioaddr & 0xfffc));
+			}
+		}
+	}
+
+	outb((brdp->ioctrlval | ECH_BRDDISABLE), brdp->ioctrl);
+
+	return handled;
+}
+
+/*****************************************************************************/
+
+/*
+ *	Interrupt service routine for ECH-MCA board types.
+ */
+
+static int stl_echmcaintr(stlbrd_t *brdp)
+{
+	stlpanel_t	*panelp;
+	unsigned int	ioaddr;
+	int		bnknr;
+	int		handled = 0;
+
+	while (inb(brdp->iostatus) & ECH_INTRPEND) {
+		handled = 1;
+		for (bnknr = 0; (bnknr < brdp->nrbnks); bnknr++) {
+			ioaddr = brdp->bnkstataddr[bnknr];
+			if (inb(ioaddr) & ECH_PNLINTRPEND) {
+				panelp = brdp->bnk2panel[bnknr];
+				(* panelp->isr)(panelp, (ioaddr & 0xfffc));
+			}
+		}
+	}
+	return handled;
+}
+
+/*****************************************************************************/
+
+/*
+ *	Interrupt service routine for ECH-PCI board types.
+ */
+
+static int stl_echpciintr(stlbrd_t *brdp)
+{
+	stlpanel_t	*panelp;
+	unsigned int	ioaddr;
+	int		bnknr, recheck;
+	int		handled = 0;
+
+	while (1) {
+		recheck = 0;
+		for (bnknr = 0; (bnknr < brdp->nrbnks); bnknr++) {
+			outb(brdp->bnkpageaddr[bnknr], brdp->ioctrl);
+			ioaddr = brdp->bnkstataddr[bnknr];
+			if (inb(ioaddr) & ECH_PNLINTRPEND) {
+				panelp = brdp->bnk2panel[bnknr];
+				(* panelp->isr)(panelp, (ioaddr & 0xfffc));
+				recheck++;
+				handled = 1;
+			}
+		}
+		if (! recheck)
+			break;
+	}
+	return handled;
+}
+
+/*****************************************************************************/
+
+/*
+ *	Interrupt service routine for ECH-8/64-PCI board types.
+ */
+
+static int stl_echpci64intr(stlbrd_t *brdp)
+{
+	stlpanel_t	*panelp;
+	unsigned int	ioaddr;
+	int		bnknr;
+	int		handled = 0;
+
+	while (inb(brdp->ioctrl) & 0x1) {
+		handled = 1;
+		for (bnknr = 0; (bnknr < brdp->nrbnks); bnknr++) {
+			ioaddr = brdp->bnkstataddr[bnknr];
+			if (inb(ioaddr) & ECH_PNLINTRPEND) {
+				panelp = brdp->bnk2panel[bnknr];
+				(* panelp->isr)(panelp, (ioaddr & 0xfffc));
+			}
+		}
+	}
+
+	return handled;
+}
+
+/*****************************************************************************/
+
+/*
+ *	Service an off-level request for some channel.
+ */
+static void stl_offintr(void *private)
+{
+	stlport_t		*portp;
+	struct tty_struct	*tty;
+	unsigned int		oldsigs;
+
+	portp = private;
+
+#ifdef DEBUG
+	printk("stl_offintr(portp=%x)\n", (int) portp);
+#endif
+
+	if (portp == (stlport_t *) NULL)
+		return;
+
+	tty = portp->tty;
+	if (tty == (struct tty_struct *) NULL)
+		return;
+
+	lock_kernel();
+	if (test_bit(ASYI_TXLOW, &portp->istate)) {
+		tty_wakeup(tty);
+	}
+	if (test_bit(ASYI_DCDCHANGE, &portp->istate)) {
+		clear_bit(ASYI_DCDCHANGE, &portp->istate);
+		oldsigs = portp->sigs;
+		portp->sigs = stl_getsignals(portp);
+		if ((portp->sigs & TIOCM_CD) && ((oldsigs & TIOCM_CD) == 0))
+			wake_up_interruptible(&portp->open_wait);
+		if ((oldsigs & TIOCM_CD) && ((portp->sigs & TIOCM_CD) == 0)) {
+			if (portp->flags & ASYNC_CHECK_CD)
+				tty_hangup(tty);	/* FIXME: module removal race here - AKPM */
+		}
+	}
+	unlock_kernel();
+}
+
+/*****************************************************************************/
+
+/*
+ *	Initialize all the ports on a panel.
+ */
+
+static int __init stl_initports(stlbrd_t *brdp, stlpanel_t *panelp)
+{
+	stlport_t	*portp;
+	int		chipmask, i;
+
+#ifdef DEBUG
+	printk("stl_initports(brdp=%x,panelp=%x)\n", (int) brdp, (int) panelp);
+#endif
+
+	chipmask = stl_panelinit(brdp, panelp);
+
+/*
+ *	All UART's are initialized (if found!). Now go through and setup
+ *	each ports data structures.
+ */
+	for (i = 0; (i < panelp->nrports); i++) {
+		portp = (stlport_t *) stl_memalloc(sizeof(stlport_t));
+		if (portp == (stlport_t *) NULL) {
+			printk("STALLION: failed to allocate memory "
+				"(size=%d)\n", sizeof(stlport_t));
+			break;
+		}
+		memset(portp, 0, sizeof(stlport_t));
+
+		portp->magic = STL_PORTMAGIC;
+		portp->portnr = i;
+		portp->brdnr = panelp->brdnr;
+		portp->panelnr = panelp->panelnr;
+		portp->uartp = panelp->uartp;
+		portp->clk = brdp->clk;
+		portp->baud_base = STL_BAUDBASE;
+		portp->close_delay = STL_CLOSEDELAY;
+		portp->closing_wait = 30 * HZ;
+		INIT_WORK(&portp->tqueue, stl_offintr, portp);
+		init_waitqueue_head(&portp->open_wait);
+		init_waitqueue_head(&portp->close_wait);
+		portp->stats.brd = portp->brdnr;
+		portp->stats.panel = portp->panelnr;
+		portp->stats.port = portp->portnr;
+		panelp->ports[i] = portp;
+		stl_portinit(brdp, panelp, portp);
+	}
+
+	return(0);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Try to find and initialize an EasyIO board.
+ */
+
+static inline int stl_initeio(stlbrd_t *brdp)
+{
+	stlpanel_t	*panelp;
+	unsigned int	status;
+	char		*name;
+	int		rc;
+
+#ifdef DEBUG
+	printk("stl_initeio(brdp=%x)\n", (int) brdp);
+#endif
+
+	brdp->ioctrl = brdp->ioaddr1 + 1;
+	brdp->iostatus = brdp->ioaddr1 + 2;
+
+	status = inb(brdp->iostatus);
+	if ((status & EIO_IDBITMASK) == EIO_MK3)
+		brdp->ioctrl++;
+
+/*
+ *	Handle board specific stuff now. The real difference is PCI
+ *	or not PCI.
+ */
+	if (brdp->brdtype == BRD_EASYIOPCI) {
+		brdp->iosize1 = 0x80;
+		brdp->iosize2 = 0x80;
+		name = "serial(EIO-PCI)";
+		outb(0x41, (brdp->ioaddr2 + 0x4c));
+	} else {
+		brdp->iosize1 = 8;
+		name = "serial(EIO)";
+		if ((brdp->irq < 0) || (brdp->irq > 15) ||
+		    (stl_vecmap[brdp->irq] == (unsigned char) 0xff)) {
+			printk("STALLION: invalid irq=%d for brd=%d\n",
+				brdp->irq, brdp->brdnr);
+			return(-EINVAL);
+		}
+		outb((stl_vecmap[brdp->irq] | EIO_0WS |
+			((brdp->irqtype) ? EIO_INTLEVEL : EIO_INTEDGE)),
+			brdp->ioctrl);
+	}
+
+	if (!request_region(brdp->ioaddr1, brdp->iosize1, name)) {
+		printk(KERN_WARNING "STALLION: Warning, board %d I/O address "
+			"%x conflicts with another device\n", brdp->brdnr, 
+			brdp->ioaddr1);
+		return(-EBUSY);
+	}
+	
+	if (brdp->iosize2 > 0)
+		if (!request_region(brdp->ioaddr2, brdp->iosize2, name)) {
+			printk(KERN_WARNING "STALLION: Warning, board %d I/O "
+				"address %x conflicts with another device\n",
+				brdp->brdnr, brdp->ioaddr2);
+			printk(KERN_WARNING "STALLION: Warning, also "
+				"releasing board %d I/O address %x \n", 
+				brdp->brdnr, brdp->ioaddr1);
+			release_region(brdp->ioaddr1, brdp->iosize1);
+        		return(-EBUSY);
+		}
+
+/*
+ *	Everything looks OK, so let's go ahead and probe for the hardware.
+ */
+	brdp->clk = CD1400_CLK;
+	brdp->isr = stl_eiointr;
+
+	switch (status & EIO_IDBITMASK) {
+	case EIO_8PORTM:
+		brdp->clk = CD1400_CLK8M;
+		/* fall thru */
+	case EIO_8PORTRS:
+	case EIO_8PORTDI:
+		brdp->nrports = 8;
+		break;
+	case EIO_4PORTRS:
+		brdp->nrports = 4;
+		break;
+	case EIO_MK3:
+		switch (status & EIO_BRDMASK) {
+		case ID_BRD4:
+			brdp->nrports = 4;
+			break;
+		case ID_BRD8:
+			brdp->nrports = 8;
+			break;
+		case ID_BRD16:
+			brdp->nrports = 16;
+			break;
+		default:
+			return(-ENODEV);
+		}
+		break;
+	default:
+		return(-ENODEV);
+	}
+
+/*
+ *	We have verified that the board is actually present, so now we
+ *	can complete the setup.
+ */
+
+	panelp = (stlpanel_t *) stl_memalloc(sizeof(stlpanel_t));
+	if (panelp == (stlpanel_t *) NULL) {
+		printk(KERN_WARNING "STALLION: failed to allocate memory "
+			"(size=%d)\n", sizeof(stlpanel_t));
+		return(-ENOMEM);
+	}
+	memset(panelp, 0, sizeof(stlpanel_t));
+
+	panelp->magic = STL_PANELMAGIC;
+	panelp->brdnr = brdp->brdnr;
+	panelp->panelnr = 0;
+	panelp->nrports = brdp->nrports;
+	panelp->iobase = brdp->ioaddr1;
+	panelp->hwid = status;
+	if ((status & EIO_IDBITMASK) == EIO_MK3) {
+		panelp->uartp = (void *) &stl_sc26198uart;
+		panelp->isr = stl_sc26198intr;
+	} else {
+		panelp->uartp = (void *) &stl_cd1400uart;
+		panelp->isr = stl_cd1400eiointr;
+	}
+
+	brdp->panels[0] = panelp;
+	brdp->nrpanels = 1;
+	brdp->state |= BRD_FOUND;
+	brdp->hwid = status;
+	if (request_irq(brdp->irq, stl_intr, SA_SHIRQ, name, brdp) != 0) {
+		printk("STALLION: failed to register interrupt "
+		    "routine for %s irq=%d\n", name, brdp->irq);
+		rc = -ENODEV;
+	} else {
+		rc = 0;
+	}
+	return(rc);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Try to find an ECH board and initialize it. This code is capable of
+ *	dealing with all types of ECH board.
+ */
+
+static inline int stl_initech(stlbrd_t *brdp)
+{
+	stlpanel_t	*panelp;
+	unsigned int	status, nxtid, ioaddr, conflict;
+	int		panelnr, banknr, i;
+	char		*name;
+
+#ifdef DEBUG
+	printk("stl_initech(brdp=%x)\n", (int) brdp);
+#endif
+
+	status = 0;
+	conflict = 0;
+
+/*
+ *	Set up the initial board register contents for boards. This varies a
+ *	bit between the different board types. So we need to handle each
+ *	separately. Also do a check that the supplied IRQ is good.
+ */
+	switch (brdp->brdtype) {
+
+	case BRD_ECH:
+		brdp->isr = stl_echatintr;
+		brdp->ioctrl = brdp->ioaddr1 + 1;
+		brdp->iostatus = brdp->ioaddr1 + 1;
+		status = inb(brdp->iostatus);
+		if ((status & ECH_IDBITMASK) != ECH_ID)
+			return(-ENODEV);
+		if ((brdp->irq < 0) || (brdp->irq > 15) ||
+		    (stl_vecmap[brdp->irq] == (unsigned char) 0xff)) {
+			printk("STALLION: invalid irq=%d for brd=%d\n",
+				brdp->irq, brdp->brdnr);
+			return(-EINVAL);
+		}
+		status = ((brdp->ioaddr2 & ECH_ADDR2MASK) >> 1);
+		status |= (stl_vecmap[brdp->irq] << 1);
+		outb((status | ECH_BRDRESET), brdp->ioaddr1);
+		brdp->ioctrlval = ECH_INTENABLE |
+			((brdp->irqtype) ? ECH_INTLEVEL : ECH_INTEDGE);
+		for (i = 0; (i < 10); i++)
+			outb((brdp->ioctrlval | ECH_BRDENABLE), brdp->ioctrl);
+		brdp->iosize1 = 2;
+		brdp->iosize2 = 32;
+		name = "serial(EC8/32)";
+		outb(status, brdp->ioaddr1);
+		break;
+
+	case BRD_ECHMC:
+		brdp->isr = stl_echmcaintr;
+		brdp->ioctrl = brdp->ioaddr1 + 0x20;
+		brdp->iostatus = brdp->ioctrl;
+		status = inb(brdp->iostatus);
+		if ((status & ECH_IDBITMASK) != ECH_ID)
+			return(-ENODEV);
+		if ((brdp->irq < 0) || (brdp->irq > 15) ||
+		    (stl_vecmap[brdp->irq] == (unsigned char) 0xff)) {
+			printk("STALLION: invalid irq=%d for brd=%d\n",
+				brdp->irq, brdp->brdnr);
+			return(-EINVAL);
+		}
+		outb(ECHMC_BRDRESET, brdp->ioctrl);
+		outb(ECHMC_INTENABLE, brdp->ioctrl);
+		brdp->iosize1 = 64;
+		name = "serial(EC8/32-MC)";
+		break;
+
+	case BRD_ECHPCI:
+		brdp->isr = stl_echpciintr;
+		brdp->ioctrl = brdp->ioaddr1 + 2;
+		brdp->iosize1 = 4;
+		brdp->iosize2 = 8;
+		name = "serial(EC8/32-PCI)";
+		break;
+
+	case BRD_ECH64PCI:
+		brdp->isr = stl_echpci64intr;
+		brdp->ioctrl = brdp->ioaddr2 + 0x40;
+		outb(0x43, (brdp->ioaddr1 + 0x4c));
+		brdp->iosize1 = 0x80;
+		brdp->iosize2 = 0x80;
+		name = "serial(EC8/64-PCI)";
+		break;
+
+	default:
+		printk("STALLION: unknown board type=%d\n", brdp->brdtype);
+		return(-EINVAL);
+		break;
+	}
+
+/*
+ *	Check boards for possible IO address conflicts and return fail status 
+ * 	if an IO conflict found.
+ */
+	if (!request_region(brdp->ioaddr1, brdp->iosize1, name)) {
+		printk(KERN_WARNING "STALLION: Warning, board %d I/O address "
+			"%x conflicts with another device\n", brdp->brdnr, 
+			brdp->ioaddr1);
+		return(-EBUSY);
+	}
+	
+	if (brdp->iosize2 > 0)
+		if (!request_region(brdp->ioaddr2, brdp->iosize2, name)) {
+			printk(KERN_WARNING "STALLION: Warning, board %d I/O "
+				"address %x conflicts with another device\n",
+				brdp->brdnr, brdp->ioaddr2);
+			printk(KERN_WARNING "STALLION: Warning, also "
+				"releasing board %d I/O address %x \n", 
+				brdp->brdnr, brdp->ioaddr1);
+			release_region(brdp->ioaddr1, brdp->iosize1);
+			return(-EBUSY);
+		}
+
+/*
+ *	Scan through the secondary io address space looking for panels.
+ *	As we find'em allocate and initialize panel structures for each.
+ */
+	brdp->clk = CD1400_CLK;
+	brdp->hwid = status;
+
+	ioaddr = brdp->ioaddr2;
+	banknr = 0;
+	panelnr = 0;
+	nxtid = 0;
+
+	for (i = 0; (i < STL_MAXPANELS); i++) {
+		if (brdp->brdtype == BRD_ECHPCI) {
+			outb(nxtid, brdp->ioctrl);
+			ioaddr = brdp->ioaddr2;
+		}
+		status = inb(ioaddr + ECH_PNLSTATUS);
+		if ((status & ECH_PNLIDMASK) != nxtid)
+			break;
+		panelp = (stlpanel_t *) stl_memalloc(sizeof(stlpanel_t));
+		if (panelp == (stlpanel_t *) NULL) {
+			printk("STALLION: failed to allocate memory "
+				"(size=%d)\n", sizeof(stlpanel_t));
+			break;
+		}
+		memset(panelp, 0, sizeof(stlpanel_t));
+		panelp->magic = STL_PANELMAGIC;
+		panelp->brdnr = brdp->brdnr;
+		panelp->panelnr = panelnr;
+		panelp->iobase = ioaddr;
+		panelp->pagenr = nxtid;
+		panelp->hwid = status;
+		brdp->bnk2panel[banknr] = panelp;
+		brdp->bnkpageaddr[banknr] = nxtid;
+		brdp->bnkstataddr[banknr++] = ioaddr + ECH_PNLSTATUS;
+
+		if (status & ECH_PNLXPID) {
+			panelp->uartp = (void *) &stl_sc26198uart;
+			panelp->isr = stl_sc26198intr;
+			if (status & ECH_PNL16PORT) {
+				panelp->nrports = 16;
+				brdp->bnk2panel[banknr] = panelp;
+				brdp->bnkpageaddr[banknr] = nxtid;
+				brdp->bnkstataddr[banknr++] = ioaddr + 4 +
+					ECH_PNLSTATUS;
+			} else {
+				panelp->nrports = 8;
+			}
+		} else {
+			panelp->uartp = (void *) &stl_cd1400uart;
+			panelp->isr = stl_cd1400echintr;
+			if (status & ECH_PNL16PORT) {
+				panelp->nrports = 16;
+				panelp->ackmask = 0x80;
+				if (brdp->brdtype != BRD_ECHPCI)
+					ioaddr += EREG_BANKSIZE;
+				brdp->bnk2panel[banknr] = panelp;
+				brdp->bnkpageaddr[banknr] = ++nxtid;
+				brdp->bnkstataddr[banknr++] = ioaddr +
+					ECH_PNLSTATUS;
+			} else {
+				panelp->nrports = 8;
+				panelp->ackmask = 0xc0;
+			}
+		}
+
+		nxtid++;
+		ioaddr += EREG_BANKSIZE;
+		brdp->nrports += panelp->nrports;
+		brdp->panels[panelnr++] = panelp;
+		if ((brdp->brdtype != BRD_ECHPCI) &&
+		    (ioaddr >= (brdp->ioaddr2 + brdp->iosize2)))
+			break;
+	}
+
+	brdp->nrpanels = panelnr;
+	brdp->nrbnks = banknr;
+	if (brdp->brdtype == BRD_ECH)
+		outb((brdp->ioctrlval | ECH_BRDDISABLE), brdp->ioctrl);
+
+	brdp->state |= BRD_FOUND;
+	if (request_irq(brdp->irq, stl_intr, SA_SHIRQ, name, brdp) != 0) {
+		printk("STALLION: failed to register interrupt "
+		    "routine for %s irq=%d\n", name, brdp->irq);
+		i = -ENODEV;
+	} else {
+		i = 0;
+	}
+
+	return(i);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Initialize and configure the specified board.
+ *	Scan through all the boards in the configuration and see what we
+ *	can find. Handle EIO and the ECH boards a little differently here
+ *	since the initial search and setup is very different.
+ */
+
+static int __init stl_brdinit(stlbrd_t *brdp)
+{
+	int	i;
+
+#ifdef DEBUG
+	printk("stl_brdinit(brdp=%x)\n", (int) brdp);
+#endif
+
+	switch (brdp->brdtype) {
+	case BRD_EASYIO:
+	case BRD_EASYIOPCI:
+		stl_initeio(brdp);
+		break;
+	case BRD_ECH:
+	case BRD_ECHMC:
+	case BRD_ECHPCI:
+	case BRD_ECH64PCI:
+		stl_initech(brdp);
+		break;
+	default:
+		printk("STALLION: board=%d is unknown board type=%d\n",
+			brdp->brdnr, brdp->brdtype);
+		return(ENODEV);
+	}
+
+	stl_brds[brdp->brdnr] = brdp;
+	if ((brdp->state & BRD_FOUND) == 0) {
+		printk("STALLION: %s board not found, board=%d io=%x irq=%d\n",
+			stl_brdnames[brdp->brdtype], brdp->brdnr,
+			brdp->ioaddr1, brdp->irq);
+		return(ENODEV);
+	}
+
+	for (i = 0; (i < STL_MAXPANELS); i++)
+		if (brdp->panels[i] != (stlpanel_t *) NULL)
+			stl_initports(brdp, brdp->panels[i]);
+
+	printk("STALLION: %s found, board=%d io=%x irq=%d "
+		"nrpanels=%d nrports=%d\n", stl_brdnames[brdp->brdtype],
+		brdp->brdnr, brdp->ioaddr1, brdp->irq, brdp->nrpanels,
+		brdp->nrports);
+	return(0);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Find the next available board number that is free.
+ */
+
+static inline int stl_getbrdnr(void)
+{
+	int	i;
+
+	for (i = 0; (i < STL_MAXBRDS); i++) {
+		if (stl_brds[i] == (stlbrd_t *) NULL) {
+			if (i >= stl_nrbrds)
+				stl_nrbrds = i + 1;
+			return(i);
+		}
+	}
+	return(-1);
+}
+
+/*****************************************************************************/
+
+#ifdef	CONFIG_PCI
+
+/*
+ *	We have a Stallion board. Allocate a board structure and
+ *	initialize it. Read its IO and IRQ resources from PCI
+ *	configuration space.
+ */
+
+static inline int stl_initpcibrd(int brdtype, struct pci_dev *devp)
+{
+	stlbrd_t	*brdp;
+
+#ifdef DEBUG
+	printk("stl_initpcibrd(brdtype=%d,busnr=%x,devnr=%x)\n", brdtype,
+		devp->bus->number, devp->devfn);
+#endif
+
+	if (pci_enable_device(devp))
+		return(-EIO);
+	if ((brdp = stl_allocbrd()) == (stlbrd_t *) NULL)
+		return(-ENOMEM);
+	if ((brdp->brdnr = stl_getbrdnr()) < 0) {
+		printk("STALLION: too many boards found, "
+			"maximum supported %d\n", STL_MAXBRDS);
+		return(0);
+	}
+	brdp->brdtype = brdtype;
+
+/*
+ *	Different Stallion boards use the BAR registers in different ways,
+ *	so set up io addresses based on board type.
+ */
+#ifdef DEBUG
+	printk("%s(%d): BAR[]=%x,%x,%x,%x IRQ=%x\n", __FILE__, __LINE__,
+		pci_resource_start(devp, 0), pci_resource_start(devp, 1),
+		pci_resource_start(devp, 2), pci_resource_start(devp, 3), devp->irq);
+#endif
+
+/*
+ *	We have all resources from the board, so let's setup the actual
+ *	board structure now.
+ */
+	switch (brdtype) {
+	case BRD_ECHPCI:
+		brdp->ioaddr2 = pci_resource_start(devp, 0);
+		brdp->ioaddr1 = pci_resource_start(devp, 1);
+		break;
+	case BRD_ECH64PCI:
+		brdp->ioaddr2 = pci_resource_start(devp, 2);
+		brdp->ioaddr1 = pci_resource_start(devp, 1);
+		break;
+	case BRD_EASYIOPCI:
+		brdp->ioaddr1 = pci_resource_start(devp, 2);
+		brdp->ioaddr2 = pci_resource_start(devp, 1);
+		break;
+	default:
+		printk("STALLION: unknown PCI board type=%d\n", brdtype);
+		break;
+	}
+
+	brdp->irq = devp->irq;
+	stl_brdinit(brdp);
+
+	return(0);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Find all Stallion PCI boards that might be installed. Initialize each
+ *	one as it is found.
+ */
+
+
+static inline int stl_findpcibrds(void)
+{
+	struct pci_dev	*dev = NULL;
+	int		i, rc;
+
+#ifdef DEBUG
+	printk("stl_findpcibrds()\n");
+#endif
+
+	for (i = 0; (i < stl_nrpcibrds); i++)
+		while ((dev = pci_find_device(stl_pcibrds[i].vendid,
+		    stl_pcibrds[i].devid, dev))) {
+
+/*
+ *			Found a device on the PCI bus that has our vendor and
+ *			device ID. Need to check now that it is really us.
+ */
+			if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
+				continue;
+
+			rc = stl_initpcibrd(stl_pcibrds[i].brdtype, dev);
+			if (rc)
+				return(rc);
+		}
+
+	return(0);
+}
+
+#endif
+
+/*****************************************************************************/
+
+/*
+ *	Scan through all the boards in the configuration and see what we
+ *	can find. Handle EIO and the ECH boards a little differently here
+ *	since the initial search and setup is too different.
+ */
+
+static inline int stl_initbrds(void)
+{
+	stlbrd_t	*brdp;
+	stlconf_t	*confp;
+	int		i;
+
+#ifdef DEBUG
+	printk("stl_initbrds()\n");
+#endif
+
+	if (stl_nrbrds > STL_MAXBRDS) {
+		printk("STALLION: too many boards in configuration table, "
+			"truncating to %d\n", STL_MAXBRDS);
+		stl_nrbrds = STL_MAXBRDS;
+	}
+
+/*
+ *	Firstly scan the list of static boards configured. Allocate
+ *	resources and initialize the boards as found.
+ */
+	for (i = 0; (i < stl_nrbrds); i++) {
+		confp = &stl_brdconf[i];
+		stl_parsebrd(confp, stl_brdsp[i]);
+		if ((brdp = stl_allocbrd()) == (stlbrd_t *) NULL)
+			return(-ENOMEM);
+		brdp->brdnr = i;
+		brdp->brdtype = confp->brdtype;
+		brdp->ioaddr1 = confp->ioaddr1;
+		brdp->ioaddr2 = confp->ioaddr2;
+		brdp->irq = confp->irq;
+		brdp->irqtype = confp->irqtype;
+		stl_brdinit(brdp);
+	}
+
+/*
+ *	Find any dynamically supported boards. That is via module load
+ *	line options or auto-detected on the PCI bus.
+ */
+	stl_argbrds();
+#ifdef CONFIG_PCI
+	stl_findpcibrds();
+#endif
+
+	return(0);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Return the board stats structure to user app.
+ */
+
+static int stl_getbrdstats(combrd_t __user *bp)
+{
+	stlbrd_t	*brdp;
+	stlpanel_t	*panelp;
+	int		i;
+
+	if (copy_from_user(&stl_brdstats, bp, sizeof(combrd_t)))
+		return -EFAULT;
+	if (stl_brdstats.brd >= STL_MAXBRDS)
+		return(-ENODEV);
+	brdp = stl_brds[stl_brdstats.brd];
+	if (brdp == (stlbrd_t *) NULL)
+		return(-ENODEV);
+
+	memset(&stl_brdstats, 0, sizeof(combrd_t));
+	stl_brdstats.brd = brdp->brdnr;
+	stl_brdstats.type = brdp->brdtype;
+	stl_brdstats.hwid = brdp->hwid;
+	stl_brdstats.state = brdp->state;
+	stl_brdstats.ioaddr = brdp->ioaddr1;
+	stl_brdstats.ioaddr2 = brdp->ioaddr2;
+	stl_brdstats.irq = brdp->irq;
+	stl_brdstats.nrpanels = brdp->nrpanels;
+	stl_brdstats.nrports = brdp->nrports;
+	for (i = 0; (i < brdp->nrpanels); i++) {
+		panelp = brdp->panels[i];
+		stl_brdstats.panels[i].panel = i;
+		stl_brdstats.panels[i].hwid = panelp->hwid;
+		stl_brdstats.panels[i].nrports = panelp->nrports;
+	}
+
+	return copy_to_user(bp, &stl_brdstats, sizeof(combrd_t)) ? -EFAULT : 0;
+}
+
+/*****************************************************************************/
+
+/*
+ *	Resolve the referenced port number into a port struct pointer.
+ */
+
+static stlport_t *stl_getport(int brdnr, int panelnr, int portnr)
+{
+	stlbrd_t	*brdp;
+	stlpanel_t	*panelp;
+
+	if ((brdnr < 0) || (brdnr >= STL_MAXBRDS))
+		return((stlport_t *) NULL);
+	brdp = stl_brds[brdnr];
+	if (brdp == (stlbrd_t *) NULL)
+		return((stlport_t *) NULL);
+	if ((panelnr < 0) || (panelnr >= brdp->nrpanels))
+		return((stlport_t *) NULL);
+	panelp = brdp->panels[panelnr];
+	if (panelp == (stlpanel_t *) NULL)
+		return((stlport_t *) NULL);
+	if ((portnr < 0) || (portnr >= panelp->nrports))
+		return((stlport_t *) NULL);
+	return(panelp->ports[portnr]);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Return the port stats structure to user app. A NULL port struct
+ *	pointer passed in means that we need to find out from the app
+ *	what port to get stats for (used through board control device).
+ */
+
+static int stl_getportstats(stlport_t *portp, comstats_t __user *cp)
+{
+	unsigned char	*head, *tail;
+	unsigned long	flags;
+
+	if (!portp) {
+		if (copy_from_user(&stl_comstats, cp, sizeof(comstats_t)))
+			return -EFAULT;
+		portp = stl_getport(stl_comstats.brd, stl_comstats.panel,
+			stl_comstats.port);
+		if (portp == (stlport_t *) NULL)
+			return(-ENODEV);
+	}
+
+	portp->stats.state = portp->istate;
+	portp->stats.flags = portp->flags;
+	portp->stats.hwid = portp->hwid;
+
+	portp->stats.ttystate = 0;
+	portp->stats.cflags = 0;
+	portp->stats.iflags = 0;
+	portp->stats.oflags = 0;
+	portp->stats.lflags = 0;
+	portp->stats.rxbuffered = 0;
+
+	save_flags(flags);
+	cli();
+	if (portp->tty != (struct tty_struct *) NULL) {
+		if (portp->tty->driver_data == portp) {
+			portp->stats.ttystate = portp->tty->flags;
+			portp->stats.rxbuffered = portp->tty->flip.count;
+			if (portp->tty->termios != (struct termios *) NULL) {
+				portp->stats.cflags = portp->tty->termios->c_cflag;
+				portp->stats.iflags = portp->tty->termios->c_iflag;
+				portp->stats.oflags = portp->tty->termios->c_oflag;
+				portp->stats.lflags = portp->tty->termios->c_lflag;
+			}
+		}
+	}
+	restore_flags(flags);
+
+	head = portp->tx.head;
+	tail = portp->tx.tail;
+	portp->stats.txbuffered = ((head >= tail) ? (head - tail) :
+		(STL_TXBUFSIZE - (tail - head)));
+
+	portp->stats.signals = (unsigned long) stl_getsignals(portp);
+
+	return copy_to_user(cp, &portp->stats,
+			    sizeof(comstats_t)) ? -EFAULT : 0;
+}
+
+/*****************************************************************************/
+
+/*
+ *	Clear the port stats structure. We also return it zeroed out...
+ */
+
+static int stl_clrportstats(stlport_t *portp, comstats_t __user *cp)
+{
+	if (!portp) {
+		if (copy_from_user(&stl_comstats, cp, sizeof(comstats_t)))
+			return -EFAULT;
+		portp = stl_getport(stl_comstats.brd, stl_comstats.panel,
+			stl_comstats.port);
+		if (portp == (stlport_t *) NULL)
+			return(-ENODEV);
+	}
+
+	memset(&portp->stats, 0, sizeof(comstats_t));
+	portp->stats.brd = portp->brdnr;
+	portp->stats.panel = portp->panelnr;
+	portp->stats.port = portp->portnr;
+	return copy_to_user(cp, &portp->stats,
+			    sizeof(comstats_t)) ? -EFAULT : 0;
+}
+
+/*****************************************************************************/
+
+/*
+ *	Return the entire driver ports structure to a user app.
+ */
+
+static int stl_getportstruct(stlport_t __user *arg)
+{
+	stlport_t	*portp;
+
+	if (copy_from_user(&stl_dummyport, arg, sizeof(stlport_t)))
+		return -EFAULT;
+	portp = stl_getport(stl_dummyport.brdnr, stl_dummyport.panelnr,
+		 stl_dummyport.portnr);
+	if (!portp)
+		return -ENODEV;
+	return copy_to_user(arg, portp, sizeof(stlport_t)) ? -EFAULT : 0;
+}
+
+/*****************************************************************************/
+
+/*
+ *	Return the entire driver board structure to a user app.
+ */
+
+static int stl_getbrdstruct(stlbrd_t __user *arg)
+{
+	stlbrd_t	*brdp;
+
+	if (copy_from_user(&stl_dummybrd, arg, sizeof(stlbrd_t)))
+		return -EFAULT;
+	if ((stl_dummybrd.brdnr < 0) || (stl_dummybrd.brdnr >= STL_MAXBRDS))
+		return -ENODEV;
+	brdp = stl_brds[stl_dummybrd.brdnr];
+	if (!brdp)
+		return(-ENODEV);
+	return copy_to_user(arg, brdp, sizeof(stlbrd_t)) ? -EFAULT : 0;
+}
+
+/*****************************************************************************/
+
+/*
+ *	The "staliomem" device is also required to do some special operations
+ *	on the board and/or ports. In this driver it is mostly used for stats
+ *	collection.
+ */
+
+static int stl_memioctl(struct inode *ip, struct file *fp, unsigned int cmd, unsigned long arg)
+{
+	int	brdnr, rc;
+	void __user *argp = (void __user *)arg;
+
+#ifdef DEBUG
+	printk("stl_memioctl(ip=%x,fp=%x,cmd=%x,arg=%x)\n", (int) ip,
+		(int) fp, cmd, (int) arg);
+#endif
+
+	brdnr = iminor(ip);
+	if (brdnr >= STL_MAXBRDS)
+		return(-ENODEV);
+	rc = 0;
+
+	switch (cmd) {
+	case COM_GETPORTSTATS:
+		rc = stl_getportstats(NULL, argp);
+		break;
+	case COM_CLRPORTSTATS:
+		rc = stl_clrportstats(NULL, argp);
+		break;
+	case COM_GETBRDSTATS:
+		rc = stl_getbrdstats(argp);
+		break;
+	case COM_READPORT:
+		rc = stl_getportstruct(argp);
+		break;
+	case COM_READBOARD:
+		rc = stl_getbrdstruct(argp);
+		break;
+	default:
+		rc = -ENOIOCTLCMD;
+		break;
+	}
+
+	return(rc);
+}
+
+static struct tty_operations stl_ops = {
+	.open = stl_open,
+	.close = stl_close,
+	.write = stl_write,
+	.put_char = stl_putchar,
+	.flush_chars = stl_flushchars,
+	.write_room = stl_writeroom,
+	.chars_in_buffer = stl_charsinbuffer,
+	.ioctl = stl_ioctl,
+	.set_termios = stl_settermios,
+	.throttle = stl_throttle,
+	.unthrottle = stl_unthrottle,
+	.stop = stl_stop,
+	.start = stl_start,
+	.hangup = stl_hangup,
+	.flush_buffer = stl_flushbuffer,
+	.break_ctl = stl_breakctl,
+	.wait_until_sent = stl_waituntilsent,
+	.send_xchar = stl_sendxchar,
+	.read_proc = stl_readproc,
+	.tiocmget = stl_tiocmget,
+	.tiocmset = stl_tiocmset,
+};
+
+/*****************************************************************************/
+
+int __init stl_init(void)
+{
+	int i;
+	printk(KERN_INFO "%s: version %s\n", stl_drvtitle, stl_drvversion);
+
+	stl_initbrds();
+
+	stl_serial = alloc_tty_driver(STL_MAXBRDS * STL_MAXPORTS);
+	if (!stl_serial)
+		return -1;
+
+/*
+ *	Allocate a temporary write buffer.
+ */
+	stl_tmpwritebuf = (char *) stl_memalloc(STL_TXBUFSIZE);
+	if (stl_tmpwritebuf == (char *) NULL)
+		printk("STALLION: failed to allocate memory (size=%d)\n",
+			STL_TXBUFSIZE);
+
+/*
+ *	Set up a character driver for per board stuff. This is mainly used
+ *	to do stats ioctls on the ports.
+ */
+	if (register_chrdev(STL_SIOMEMMAJOR, "staliomem", &stl_fsiomem))
+		printk("STALLION: failed to register serial board device\n");
+	devfs_mk_dir("staliomem");
+
+	stallion_class = class_simple_create(THIS_MODULE, "staliomem");
+	for (i = 0; i < 4; i++) {
+		devfs_mk_cdev(MKDEV(STL_SIOMEMMAJOR, i),
+				S_IFCHR|S_IRUSR|S_IWUSR,
+				"staliomem/%d", i);
+		class_simple_device_add(stallion_class, MKDEV(STL_SIOMEMMAJOR, i), NULL, "staliomem%d", i);
+	}
+
+	stl_serial->owner = THIS_MODULE;
+	stl_serial->driver_name = stl_drvname;
+	stl_serial->name = "ttyE";
+	stl_serial->devfs_name = "tts/E";
+	stl_serial->major = STL_SERIALMAJOR;
+	stl_serial->minor_start = 0;
+	stl_serial->type = TTY_DRIVER_TYPE_SERIAL;
+	stl_serial->subtype = SERIAL_TYPE_NORMAL;
+	stl_serial->init_termios = stl_deftermios;
+	stl_serial->flags = TTY_DRIVER_REAL_RAW;
+	tty_set_operations(stl_serial, &stl_ops);
+
+	if (tty_register_driver(stl_serial)) {
+		put_tty_driver(stl_serial);
+		printk("STALLION: failed to register serial driver\n");
+		return -1;
+	}
+
+	return(0);
+}
+
+/*****************************************************************************/
+/*                       CD1400 HARDWARE FUNCTIONS                           */
+/*****************************************************************************/
+
+/*
+ *	These functions get/set/update the registers of the cd1400 UARTs.
+ *	Access to the cd1400 registers is via an address/data io port pair.
+ *	(Maybe should make this inline...)
+ */
+
+static int stl_cd1400getreg(stlport_t *portp, int regnr)
+{
+	outb((regnr + portp->uartaddr), portp->ioaddr);
+	return(inb(portp->ioaddr + EREG_DATA));
+}
+
+static void stl_cd1400setreg(stlport_t *portp, int regnr, int value)
+{
+	outb((regnr + portp->uartaddr), portp->ioaddr);
+	outb(value, portp->ioaddr + EREG_DATA);
+}
+
+static int stl_cd1400updatereg(stlport_t *portp, int regnr, int value)
+{
+	outb((regnr + portp->uartaddr), portp->ioaddr);
+	if (inb(portp->ioaddr + EREG_DATA) != value) {
+		outb(value, portp->ioaddr + EREG_DATA);
+		return(1);
+	}
+	return(0);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Inbitialize the UARTs in a panel. We don't care what sort of board
+ *	these ports are on - since the port io registers are almost
+ *	identical when dealing with ports.
+ */
+
+static int stl_cd1400panelinit(stlbrd_t *brdp, stlpanel_t *panelp)
+{
+	unsigned int	gfrcr;
+	int		chipmask, i, j;
+	int		nrchips, uartaddr, ioaddr;
+
+#ifdef DEBUG
+	printk("stl_panelinit(brdp=%x,panelp=%x)\n", (int) brdp, (int) panelp);
+#endif
+
+	BRDENABLE(panelp->brdnr, panelp->pagenr);
+
+/*
+ *	Check that each chip is present and started up OK.
+ */
+	chipmask = 0;
+	nrchips = panelp->nrports / CD1400_PORTS;
+	for (i = 0; (i < nrchips); i++) {
+		if (brdp->brdtype == BRD_ECHPCI) {
+			outb((panelp->pagenr + (i >> 1)), brdp->ioctrl);
+			ioaddr = panelp->iobase;
+		} else {
+			ioaddr = panelp->iobase + (EREG_BANKSIZE * (i >> 1));
+		}
+		uartaddr = (i & 0x01) ? 0x080 : 0;
+		outb((GFRCR + uartaddr), ioaddr);
+		outb(0, (ioaddr + EREG_DATA));
+		outb((CCR + uartaddr), ioaddr);
+		outb(CCR_RESETFULL, (ioaddr + EREG_DATA));
+		outb(CCR_RESETFULL, (ioaddr + EREG_DATA));
+		outb((GFRCR + uartaddr), ioaddr);
+		for (j = 0; (j < CCR_MAXWAIT); j++) {
+			if ((gfrcr = inb(ioaddr + EREG_DATA)) != 0)
+				break;
+		}
+		if ((j >= CCR_MAXWAIT) || (gfrcr < 0x40) || (gfrcr > 0x60)) {
+			printk("STALLION: cd1400 not responding, "
+				"brd=%d panel=%d chip=%d\n",
+				panelp->brdnr, panelp->panelnr, i);
+			continue;
+		}
+		chipmask |= (0x1 << i);
+		outb((PPR + uartaddr), ioaddr);
+		outb(PPR_SCALAR, (ioaddr + EREG_DATA));
+	}
+
+	BRDDISABLE(panelp->brdnr);
+	return(chipmask);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Initialize hardware specific port registers.
+ */
+
+static void stl_cd1400portinit(stlbrd_t *brdp, stlpanel_t *panelp, stlport_t *portp)
+{
+#ifdef DEBUG
+	printk("stl_cd1400portinit(brdp=%x,panelp=%x,portp=%x)\n",
+		(int) brdp, (int) panelp, (int) portp);
+#endif
+
+	if ((brdp == (stlbrd_t *) NULL) || (panelp == (stlpanel_t *) NULL) ||
+	    (portp == (stlport_t *) NULL))
+		return;
+
+	portp->ioaddr = panelp->iobase + (((brdp->brdtype == BRD_ECHPCI) ||
+		(portp->portnr < 8)) ? 0 : EREG_BANKSIZE);
+	portp->uartaddr = (portp->portnr & 0x04) << 5;
+	portp->pagenr = panelp->pagenr + (portp->portnr >> 3);
+
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_cd1400setreg(portp, CAR, (portp->portnr & 0x03));
+	stl_cd1400setreg(portp, LIVR, (portp->portnr << 3));
+	portp->hwid = stl_cd1400getreg(portp, GFRCR);
+	BRDDISABLE(portp->brdnr);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Wait for the command register to be ready. We will poll this,
+ *	since it won't usually take too long to be ready.
+ */
+
+static void stl_cd1400ccrwait(stlport_t *portp)
+{
+	int	i;
+
+	for (i = 0; (i < CCR_MAXWAIT); i++) {
+		if (stl_cd1400getreg(portp, CCR) == 0) {
+			return;
+		}
+	}
+
+	printk("STALLION: cd1400 not responding, port=%d panel=%d brd=%d\n",
+		portp->portnr, portp->panelnr, portp->brdnr);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Set up the cd1400 registers for a port based on the termios port
+ *	settings.
+ */
+
+static void stl_cd1400setport(stlport_t *portp, struct termios *tiosp)
+{
+	stlbrd_t	*brdp;
+	unsigned long	flags;
+	unsigned int	clkdiv, baudrate;
+	unsigned char	cor1, cor2, cor3;
+	unsigned char	cor4, cor5, ccr;
+	unsigned char	srer, sreron, sreroff;
+	unsigned char	mcor1, mcor2, rtpr;
+	unsigned char	clk, div;
+
+	cor1 = 0;
+	cor2 = 0;
+	cor3 = 0;
+	cor4 = 0;
+	cor5 = 0;
+	ccr = 0;
+	rtpr = 0;
+	clk = 0;
+	div = 0;
+	mcor1 = 0;
+	mcor2 = 0;
+	sreron = 0;
+	sreroff = 0;
+
+	brdp = stl_brds[portp->brdnr];
+	if (brdp == (stlbrd_t *) NULL)
+		return;
+
+/*
+ *	Set up the RX char ignore mask with those RX error types we
+ *	can ignore. We can get the cd1400 to help us out a little here,
+ *	it will ignore parity errors and breaks for us.
+ */
+	portp->rxignoremsk = 0;
+	if (tiosp->c_iflag & IGNPAR) {
+		portp->rxignoremsk |= (ST_PARITY | ST_FRAMING | ST_OVERRUN);
+		cor1 |= COR1_PARIGNORE;
+	}
+	if (tiosp->c_iflag & IGNBRK) {
+		portp->rxignoremsk |= ST_BREAK;
+		cor4 |= COR4_IGNBRK;
+	}
+
+	portp->rxmarkmsk = ST_OVERRUN;
+	if (tiosp->c_iflag & (INPCK | PARMRK))
+		portp->rxmarkmsk |= (ST_PARITY | ST_FRAMING);
+	if (tiosp->c_iflag & BRKINT)
+		portp->rxmarkmsk |= ST_BREAK;
+
+/*
+ *	Go through the char size, parity and stop bits and set all the
+ *	option register appropriately.
+ */
+	switch (tiosp->c_cflag & CSIZE) {
+	case CS5:
+		cor1 |= COR1_CHL5;
+		break;
+	case CS6:
+		cor1 |= COR1_CHL6;
+		break;
+	case CS7:
+		cor1 |= COR1_CHL7;
+		break;
+	default:
+		cor1 |= COR1_CHL8;
+		break;
+	}
+
+	if (tiosp->c_cflag & CSTOPB)
+		cor1 |= COR1_STOP2;
+	else
+		cor1 |= COR1_STOP1;
+
+	if (tiosp->c_cflag & PARENB) {
+		if (tiosp->c_cflag & PARODD)
+			cor1 |= (COR1_PARENB | COR1_PARODD);
+		else
+			cor1 |= (COR1_PARENB | COR1_PAREVEN);
+	} else {
+		cor1 |= COR1_PARNONE;
+	}
+
+/*
+ *	Set the RX FIFO threshold at 6 chars. This gives a bit of breathing
+ *	space for hardware flow control and the like. This should be set to
+ *	VMIN. Also here we will set the RX data timeout to 10ms - this should
+ *	really be based on VTIME.
+ */
+	cor3 |= FIFO_RXTHRESHOLD;
+	rtpr = 2;
+
+/*
+ *	Calculate the baud rate timers. For now we will just assume that
+ *	the input and output baud are the same. Could have used a baud
+ *	table here, but this way we can generate virtually any baud rate
+ *	we like!
+ */
+	baudrate = tiosp->c_cflag & CBAUD;
+	if (baudrate & CBAUDEX) {
+		baudrate &= ~CBAUDEX;
+		if ((baudrate < 1) || (baudrate > 4))
+			tiosp->c_cflag &= ~CBAUDEX;
+		else
+			baudrate += 15;
+	}
+	baudrate = stl_baudrates[baudrate];
+	if ((tiosp->c_cflag & CBAUD) == B38400) {
+		if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
+			baudrate = 57600;
+		else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
+			baudrate = 115200;
+		else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
+			baudrate = 230400;
+		else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
+			baudrate = 460800;
+		else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST)
+			baudrate = (portp->baud_base / portp->custom_divisor);
+	}
+	if (baudrate > STL_CD1400MAXBAUD)
+		baudrate = STL_CD1400MAXBAUD;
+
+	if (baudrate > 0) {
+		for (clk = 0; (clk < CD1400_NUMCLKS); clk++) {
+			clkdiv = ((portp->clk / stl_cd1400clkdivs[clk]) / baudrate);
+			if (clkdiv < 0x100)
+				break;
+		}
+		div = (unsigned char) clkdiv;
+	}
+
+/*
+ *	Check what form of modem signaling is required and set it up.
+ */
+	if ((tiosp->c_cflag & CLOCAL) == 0) {
+		mcor1 |= MCOR1_DCD;
+		mcor2 |= MCOR2_DCD;
+		sreron |= SRER_MODEM;
+		portp->flags |= ASYNC_CHECK_CD;
+	} else {
+		portp->flags &= ~ASYNC_CHECK_CD;
+	}
+
+/*
+ *	Setup cd1400 enhanced modes if we can. In particular we want to
+ *	handle as much of the flow control as possible automatically. As
+ *	well as saving a few CPU cycles it will also greatly improve flow
+ *	control reliability.
+ */
+	if (tiosp->c_iflag & IXON) {
+		cor2 |= COR2_TXIBE;
+		cor3 |= COR3_SCD12;
+		if (tiosp->c_iflag & IXANY)
+			cor2 |= COR2_IXM;
+	}
+
+	if (tiosp->c_cflag & CRTSCTS) {
+		cor2 |= COR2_CTSAE;
+		mcor1 |= FIFO_RTSTHRESHOLD;
+	}
+
+/*
+ *	All cd1400 register values calculated so go through and set
+ *	them all up.
+ */
+
+#ifdef DEBUG
+	printk("SETPORT: portnr=%d panelnr=%d brdnr=%d\n",
+		portp->portnr, portp->panelnr, portp->brdnr);
+	printk("    cor1=%x cor2=%x cor3=%x cor4=%x cor5=%x\n",
+		cor1, cor2, cor3, cor4, cor5);
+	printk("    mcor1=%x mcor2=%x rtpr=%x sreron=%x sreroff=%x\n",
+		mcor1, mcor2, rtpr, sreron, sreroff);
+	printk("    tcor=%x tbpr=%x rcor=%x rbpr=%x\n", clk, div, clk, div);
+	printk("    schr1=%x schr2=%x schr3=%x schr4=%x\n",
+		tiosp->c_cc[VSTART], tiosp->c_cc[VSTOP],
+		tiosp->c_cc[VSTART], tiosp->c_cc[VSTOP]);
+#endif
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_cd1400setreg(portp, CAR, (portp->portnr & 0x3));
+	srer = stl_cd1400getreg(portp, SRER);
+	stl_cd1400setreg(portp, SRER, 0);
+	if (stl_cd1400updatereg(portp, COR1, cor1))
+		ccr = 1;
+	if (stl_cd1400updatereg(portp, COR2, cor2))
+		ccr = 1;
+	if (stl_cd1400updatereg(portp, COR3, cor3))
+		ccr = 1;
+	if (ccr) {
+		stl_cd1400ccrwait(portp);
+		stl_cd1400setreg(portp, CCR, CCR_CORCHANGE);
+	}
+	stl_cd1400setreg(portp, COR4, cor4);
+	stl_cd1400setreg(portp, COR5, cor5);
+	stl_cd1400setreg(portp, MCOR1, mcor1);
+	stl_cd1400setreg(portp, MCOR2, mcor2);
+	if (baudrate > 0) {
+		stl_cd1400setreg(portp, TCOR, clk);
+		stl_cd1400setreg(portp, TBPR, div);
+		stl_cd1400setreg(portp, RCOR, clk);
+		stl_cd1400setreg(portp, RBPR, div);
+	}
+	stl_cd1400setreg(portp, SCHR1, tiosp->c_cc[VSTART]);
+	stl_cd1400setreg(portp, SCHR2, tiosp->c_cc[VSTOP]);
+	stl_cd1400setreg(portp, SCHR3, tiosp->c_cc[VSTART]);
+	stl_cd1400setreg(portp, SCHR4, tiosp->c_cc[VSTOP]);
+	stl_cd1400setreg(portp, RTPR, rtpr);
+	mcor1 = stl_cd1400getreg(portp, MSVR1);
+	if (mcor1 & MSVR1_DCD)
+		portp->sigs |= TIOCM_CD;
+	else
+		portp->sigs &= ~TIOCM_CD;
+	stl_cd1400setreg(portp, SRER, ((srer & ~sreroff) | sreron));
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Set the state of the DTR and RTS signals.
+ */
+
+static void stl_cd1400setsignals(stlport_t *portp, int dtr, int rts)
+{
+	unsigned char	msvr1, msvr2;
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_cd1400setsignals(portp=%x,dtr=%d,rts=%d)\n",
+		(int) portp, dtr, rts);
+#endif
+
+	msvr1 = 0;
+	msvr2 = 0;
+	if (dtr > 0)
+		msvr1 = MSVR1_DTR;
+	if (rts > 0)
+		msvr2 = MSVR2_RTS;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_cd1400setreg(portp, CAR, (portp->portnr & 0x03));
+	if (rts >= 0)
+		stl_cd1400setreg(portp, MSVR2, msvr2);
+	if (dtr >= 0)
+		stl_cd1400setreg(portp, MSVR1, msvr1);
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Return the state of the signals.
+ */
+
+static int stl_cd1400getsignals(stlport_t *portp)
+{
+	unsigned char	msvr1, msvr2;
+	unsigned long	flags;
+	int		sigs;
+
+#ifdef DEBUG
+	printk("stl_cd1400getsignals(portp=%x)\n", (int) portp);
+#endif
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_cd1400setreg(portp, CAR, (portp->portnr & 0x03));
+	msvr1 = stl_cd1400getreg(portp, MSVR1);
+	msvr2 = stl_cd1400getreg(portp, MSVR2);
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+
+	sigs = 0;
+	sigs |= (msvr1 & MSVR1_DCD) ? TIOCM_CD : 0;
+	sigs |= (msvr1 & MSVR1_CTS) ? TIOCM_CTS : 0;
+	sigs |= (msvr1 & MSVR1_DTR) ? TIOCM_DTR : 0;
+	sigs |= (msvr2 & MSVR2_RTS) ? TIOCM_RTS : 0;
+#if 0
+	sigs |= (msvr1 & MSVR1_RI) ? TIOCM_RI : 0;
+	sigs |= (msvr1 & MSVR1_DSR) ? TIOCM_DSR : 0;
+#else
+	sigs |= TIOCM_DSR;
+#endif
+	return(sigs);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Enable/Disable the Transmitter and/or Receiver.
+ */
+
+static void stl_cd1400enablerxtx(stlport_t *portp, int rx, int tx)
+{
+	unsigned char	ccr;
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_cd1400enablerxtx(portp=%x,rx=%d,tx=%d)\n",
+		(int) portp, rx, tx);
+#endif
+	ccr = 0;
+
+	if (tx == 0)
+		ccr |= CCR_TXDISABLE;
+	else if (tx > 0)
+		ccr |= CCR_TXENABLE;
+	if (rx == 0)
+		ccr |= CCR_RXDISABLE;
+	else if (rx > 0)
+		ccr |= CCR_RXENABLE;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_cd1400setreg(portp, CAR, (portp->portnr & 0x03));
+	stl_cd1400ccrwait(portp);
+	stl_cd1400setreg(portp, CCR, ccr);
+	stl_cd1400ccrwait(portp);
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Start/stop the Transmitter and/or Receiver.
+ */
+
+static void stl_cd1400startrxtx(stlport_t *portp, int rx, int tx)
+{
+	unsigned char	sreron, sreroff;
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_cd1400startrxtx(portp=%x,rx=%d,tx=%d)\n",
+		(int) portp, rx, tx);
+#endif
+
+	sreron = 0;
+	sreroff = 0;
+	if (tx == 0)
+		sreroff |= (SRER_TXDATA | SRER_TXEMPTY);
+	else if (tx == 1)
+		sreron |= SRER_TXDATA;
+	else if (tx >= 2)
+		sreron |= SRER_TXEMPTY;
+	if (rx == 0)
+		sreroff |= SRER_RXDATA;
+	else if (rx > 0)
+		sreron |= SRER_RXDATA;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_cd1400setreg(portp, CAR, (portp->portnr & 0x03));
+	stl_cd1400setreg(portp, SRER,
+		((stl_cd1400getreg(portp, SRER) & ~sreroff) | sreron));
+	BRDDISABLE(portp->brdnr);
+	if (tx > 0)
+		set_bit(ASYI_TXBUSY, &portp->istate);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Disable all interrupts from this port.
+ */
+
+static void stl_cd1400disableintrs(stlport_t *portp)
+{
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_cd1400disableintrs(portp=%x)\n", (int) portp);
+#endif
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_cd1400setreg(portp, CAR, (portp->portnr & 0x03));
+	stl_cd1400setreg(portp, SRER, 0);
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+static void stl_cd1400sendbreak(stlport_t *portp, int len)
+{
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_cd1400sendbreak(portp=%x,len=%d)\n", (int) portp, len);
+#endif
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_cd1400setreg(portp, CAR, (portp->portnr & 0x03));
+	stl_cd1400setreg(portp, SRER,
+		((stl_cd1400getreg(portp, SRER) & ~SRER_TXDATA) |
+		SRER_TXEMPTY));
+	BRDDISABLE(portp->brdnr);
+	portp->brklen = len;
+	if (len == 1)
+		portp->stats.txbreaks++;
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Take flow control actions...
+ */
+
+static void stl_cd1400flowctrl(stlport_t *portp, int state)
+{
+	struct tty_struct	*tty;
+	unsigned long		flags;
+
+#ifdef DEBUG
+	printk("stl_cd1400flowctrl(portp=%x,state=%x)\n", (int) portp, state);
+#endif
+
+	if (portp == (stlport_t *) NULL)
+		return;
+	tty = portp->tty;
+	if (tty == (struct tty_struct *) NULL)
+		return;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_cd1400setreg(portp, CAR, (portp->portnr & 0x03));
+
+	if (state) {
+		if (tty->termios->c_iflag & IXOFF) {
+			stl_cd1400ccrwait(portp);
+			stl_cd1400setreg(portp, CCR, CCR_SENDSCHR1);
+			portp->stats.rxxon++;
+			stl_cd1400ccrwait(portp);
+		}
+/*
+ *		Question: should we return RTS to what it was before? It may
+ *		have been set by an ioctl... Suppose not, since if you have
+ *		hardware flow control set then it is pretty silly to go and
+ *		set the RTS line by hand.
+ */
+		if (tty->termios->c_cflag & CRTSCTS) {
+			stl_cd1400setreg(portp, MCOR1,
+				(stl_cd1400getreg(portp, MCOR1) |
+				FIFO_RTSTHRESHOLD));
+			stl_cd1400setreg(portp, MSVR2, MSVR2_RTS);
+			portp->stats.rxrtson++;
+		}
+	} else {
+		if (tty->termios->c_iflag & IXOFF) {
+			stl_cd1400ccrwait(portp);
+			stl_cd1400setreg(portp, CCR, CCR_SENDSCHR2);
+			portp->stats.rxxoff++;
+			stl_cd1400ccrwait(portp);
+		}
+		if (tty->termios->c_cflag & CRTSCTS) {
+			stl_cd1400setreg(portp, MCOR1,
+				(stl_cd1400getreg(portp, MCOR1) & 0xf0));
+			stl_cd1400setreg(portp, MSVR2, 0);
+			portp->stats.rxrtsoff++;
+		}
+	}
+
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Send a flow control character...
+ */
+
+static void stl_cd1400sendflow(stlport_t *portp, int state)
+{
+	struct tty_struct	*tty;
+	unsigned long		flags;
+
+#ifdef DEBUG
+	printk("stl_cd1400sendflow(portp=%x,state=%x)\n", (int) portp, state);
+#endif
+
+	if (portp == (stlport_t *) NULL)
+		return;
+	tty = portp->tty;
+	if (tty == (struct tty_struct *) NULL)
+		return;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_cd1400setreg(portp, CAR, (portp->portnr & 0x03));
+	if (state) {
+		stl_cd1400ccrwait(portp);
+		stl_cd1400setreg(portp, CCR, CCR_SENDSCHR1);
+		portp->stats.rxxon++;
+		stl_cd1400ccrwait(portp);
+	} else {
+		stl_cd1400ccrwait(portp);
+		stl_cd1400setreg(portp, CCR, CCR_SENDSCHR2);
+		portp->stats.rxxoff++;
+		stl_cd1400ccrwait(portp);
+	}
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+static void stl_cd1400flush(stlport_t *portp)
+{
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_cd1400flush(portp=%x)\n", (int) portp);
+#endif
+
+	if (portp == (stlport_t *) NULL)
+		return;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_cd1400setreg(portp, CAR, (portp->portnr & 0x03));
+	stl_cd1400ccrwait(portp);
+	stl_cd1400setreg(portp, CCR, CCR_TXFLUSHFIFO);
+	stl_cd1400ccrwait(portp);
+	portp->tx.tail = portp->tx.head;
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Return the current state of data flow on this port. This is only
+ *	really interresting when determining if data has fully completed
+ *	transmission or not... This is easy for the cd1400, it accurately
+ *	maintains the busy port flag.
+ */
+
+static int stl_cd1400datastate(stlport_t *portp)
+{
+#ifdef DEBUG
+	printk("stl_cd1400datastate(portp=%x)\n", (int) portp);
+#endif
+
+	if (portp == (stlport_t *) NULL)
+		return(0);
+
+	return(test_bit(ASYI_TXBUSY, &portp->istate) ? 1 : 0);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Interrupt service routine for cd1400 EasyIO boards.
+ */
+
+static void stl_cd1400eiointr(stlpanel_t *panelp, unsigned int iobase)
+{
+	unsigned char	svrtype;
+
+#ifdef DEBUG
+	printk("stl_cd1400eiointr(panelp=%x,iobase=%x)\n",
+		(int) panelp, iobase);
+#endif
+
+	outb(SVRR, iobase);
+	svrtype = inb(iobase + EREG_DATA);
+	if (panelp->nrports > 4) {
+		outb((SVRR + 0x80), iobase);
+		svrtype |= inb(iobase + EREG_DATA);
+	}
+
+	if (svrtype & SVRR_RX)
+		stl_cd1400rxisr(panelp, iobase);
+	else if (svrtype & SVRR_TX)
+		stl_cd1400txisr(panelp, iobase);
+	else if (svrtype & SVRR_MDM)
+		stl_cd1400mdmisr(panelp, iobase);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Interrupt service routine for cd1400 panels.
+ */
+
+static void stl_cd1400echintr(stlpanel_t *panelp, unsigned int iobase)
+{
+	unsigned char	svrtype;
+
+#ifdef DEBUG
+	printk("stl_cd1400echintr(panelp=%x,iobase=%x)\n", (int) panelp,
+		iobase);
+#endif
+
+	outb(SVRR, iobase);
+	svrtype = inb(iobase + EREG_DATA);
+	outb((SVRR + 0x80), iobase);
+	svrtype |= inb(iobase + EREG_DATA);
+	if (svrtype & SVRR_RX)
+		stl_cd1400rxisr(panelp, iobase);
+	else if (svrtype & SVRR_TX)
+		stl_cd1400txisr(panelp, iobase);
+	else if (svrtype & SVRR_MDM)
+		stl_cd1400mdmisr(panelp, iobase);
+}
+
+
+/*****************************************************************************/
+
+/*
+ *	Unfortunately we need to handle breaks in the TX data stream, since
+ *	this is the only way to generate them on the cd1400.
+ */
+
+static inline int stl_cd1400breakisr(stlport_t *portp, int ioaddr)
+{
+	if (portp->brklen == 1) {
+		outb((COR2 + portp->uartaddr), ioaddr);
+		outb((inb(ioaddr + EREG_DATA) | COR2_ETC),
+			(ioaddr + EREG_DATA));
+		outb((TDR + portp->uartaddr), ioaddr);
+		outb(ETC_CMD, (ioaddr + EREG_DATA));
+		outb(ETC_STARTBREAK, (ioaddr + EREG_DATA));
+		outb((SRER + portp->uartaddr), ioaddr);
+		outb((inb(ioaddr + EREG_DATA) & ~(SRER_TXDATA | SRER_TXEMPTY)),
+			(ioaddr + EREG_DATA));
+		return(1);
+	} else if (portp->brklen > 1) {
+		outb((TDR + portp->uartaddr), ioaddr);
+		outb(ETC_CMD, (ioaddr + EREG_DATA));
+		outb(ETC_STOPBREAK, (ioaddr + EREG_DATA));
+		portp->brklen = -1;
+		return(1);
+	} else {
+		outb((COR2 + portp->uartaddr), ioaddr);
+		outb((inb(ioaddr + EREG_DATA) & ~COR2_ETC),
+			(ioaddr + EREG_DATA));
+		portp->brklen = 0;
+	}
+	return(0);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Transmit interrupt handler. This has gotta be fast!  Handling TX
+ *	chars is pretty simple, stuff as many as possible from the TX buffer
+ *	into the cd1400 FIFO. Must also handle TX breaks here, since they
+ *	are embedded as commands in the data stream. Oh no, had to use a goto!
+ *	This could be optimized more, will do when I get time...
+ *	In practice it is possible that interrupts are enabled but that the
+ *	port has been hung up. Need to handle not having any TX buffer here,
+ *	this is done by using the side effect that head and tail will also
+ *	be NULL if the buffer has been freed.
+ */
+
+static void stl_cd1400txisr(stlpanel_t *panelp, int ioaddr)
+{
+	stlport_t	*portp;
+	int		len, stlen;
+	char		*head, *tail;
+	unsigned char	ioack, srer;
+
+#ifdef DEBUG
+	printk("stl_cd1400txisr(panelp=%x,ioaddr=%x)\n", (int) panelp, ioaddr);
+#endif
+
+	ioack = inb(ioaddr + EREG_TXACK);
+	if (((ioack & panelp->ackmask) != 0) ||
+	    ((ioack & ACK_TYPMASK) != ACK_TYPTX)) {
+		printk("STALLION: bad TX interrupt ack value=%x\n", ioack);
+		return;
+	}
+	portp = panelp->ports[(ioack >> 3)];
+
+/*
+ *	Unfortunately we need to handle breaks in the data stream, since
+ *	this is the only way to generate them on the cd1400. Do it now if
+ *	a break is to be sent.
+ */
+	if (portp->brklen != 0)
+		if (stl_cd1400breakisr(portp, ioaddr))
+			goto stl_txalldone;
+
+	head = portp->tx.head;
+	tail = portp->tx.tail;
+	len = (head >= tail) ? (head - tail) : (STL_TXBUFSIZE - (tail - head));
+	if ((len == 0) || ((len < STL_TXBUFLOW) &&
+	    (test_bit(ASYI_TXLOW, &portp->istate) == 0))) {
+		set_bit(ASYI_TXLOW, &portp->istate);
+		schedule_work(&portp->tqueue);
+	}
+
+	if (len == 0) {
+		outb((SRER + portp->uartaddr), ioaddr);
+		srer = inb(ioaddr + EREG_DATA);
+		if (srer & SRER_TXDATA) {
+			srer = (srer & ~SRER_TXDATA) | SRER_TXEMPTY;
+		} else {
+			srer &= ~(SRER_TXDATA | SRER_TXEMPTY);
+			clear_bit(ASYI_TXBUSY, &portp->istate);
+		}
+		outb(srer, (ioaddr + EREG_DATA));
+	} else {
+		len = MIN(len, CD1400_TXFIFOSIZE);
+		portp->stats.txtotal += len;
+		stlen = MIN(len, ((portp->tx.buf + STL_TXBUFSIZE) - tail));
+		outb((TDR + portp->uartaddr), ioaddr);
+		outsb((ioaddr + EREG_DATA), tail, stlen);
+		len -= stlen;
+		tail += stlen;
+		if (tail >= (portp->tx.buf + STL_TXBUFSIZE))
+			tail = portp->tx.buf;
+		if (len > 0) {
+			outsb((ioaddr + EREG_DATA), tail, len);
+			tail += len;
+		}
+		portp->tx.tail = tail;
+	}
+
+stl_txalldone:
+	outb((EOSRR + portp->uartaddr), ioaddr);
+	outb(0, (ioaddr + EREG_DATA));
+}
+
+/*****************************************************************************/
+
+/*
+ *	Receive character interrupt handler. Determine if we have good chars
+ *	or bad chars and then process appropriately. Good chars are easy
+ *	just shove the lot into the RX buffer and set all status byte to 0.
+ *	If a bad RX char then process as required. This routine needs to be
+ *	fast!  In practice it is possible that we get an interrupt on a port
+ *	that is closed. This can happen on hangups - since they completely
+ *	shutdown a port not in user context. Need to handle this case.
+ */
+
+static void stl_cd1400rxisr(stlpanel_t *panelp, int ioaddr)
+{
+	stlport_t		*portp;
+	struct tty_struct	*tty;
+	unsigned int		ioack, len, buflen;
+	unsigned char		status;
+	char			ch;
+
+#ifdef DEBUG
+	printk("stl_cd1400rxisr(panelp=%x,ioaddr=%x)\n", (int) panelp, ioaddr);
+#endif
+
+	ioack = inb(ioaddr + EREG_RXACK);
+	if ((ioack & panelp->ackmask) != 0) {
+		printk("STALLION: bad RX interrupt ack value=%x\n", ioack);
+		return;
+	}
+	portp = panelp->ports[(ioack >> 3)];
+	tty = portp->tty;
+
+	if ((ioack & ACK_TYPMASK) == ACK_TYPRXGOOD) {
+		outb((RDCR + portp->uartaddr), ioaddr);
+		len = inb(ioaddr + EREG_DATA);
+		if ((tty == (struct tty_struct *) NULL) ||
+		    (tty->flip.char_buf_ptr == (char *) NULL) ||
+		    ((buflen = TTY_FLIPBUF_SIZE - tty->flip.count) == 0)) {
+			len = MIN(len, sizeof(stl_unwanted));
+			outb((RDSR + portp->uartaddr), ioaddr);
+			insb((ioaddr + EREG_DATA), &stl_unwanted[0], len);
+			portp->stats.rxlost += len;
+			portp->stats.rxtotal += len;
+		} else {
+			len = MIN(len, buflen);
+			if (len > 0) {
+				outb((RDSR + portp->uartaddr), ioaddr);
+				insb((ioaddr + EREG_DATA), tty->flip.char_buf_ptr, len);
+				memset(tty->flip.flag_buf_ptr, 0, len);
+				tty->flip.flag_buf_ptr += len;
+				tty->flip.char_buf_ptr += len;
+				tty->flip.count += len;
+				tty_schedule_flip(tty);
+				portp->stats.rxtotal += len;
+			}
+		}
+	} else if ((ioack & ACK_TYPMASK) == ACK_TYPRXBAD) {
+		outb((RDSR + portp->uartaddr), ioaddr);
+		status = inb(ioaddr + EREG_DATA);
+		ch = inb(ioaddr + EREG_DATA);
+		if (status & ST_PARITY)
+			portp->stats.rxparity++;
+		if (status & ST_FRAMING)
+			portp->stats.rxframing++;
+		if (status & ST_OVERRUN)
+			portp->stats.rxoverrun++;
+		if (status & ST_BREAK)
+			portp->stats.rxbreaks++;
+		if (status & ST_SCHARMASK) {
+			if ((status & ST_SCHARMASK) == ST_SCHAR1)
+				portp->stats.txxon++;
+			if ((status & ST_SCHARMASK) == ST_SCHAR2)
+				portp->stats.txxoff++;
+			goto stl_rxalldone;
+		}
+		if ((tty != (struct tty_struct *) NULL) &&
+		    ((portp->rxignoremsk & status) == 0)) {
+			if (portp->rxmarkmsk & status) {
+				if (status & ST_BREAK) {
+					status = TTY_BREAK;
+					if (portp->flags & ASYNC_SAK) {
+						do_SAK(tty);
+						BRDENABLE(portp->brdnr, portp->pagenr);
+					}
+				} else if (status & ST_PARITY) {
+					status = TTY_PARITY;
+				} else if (status & ST_FRAMING) {
+					status = TTY_FRAME;
+				} else if(status & ST_OVERRUN) {
+					status = TTY_OVERRUN;
+				} else {
+					status = 0;
+				}
+			} else {
+				status = 0;
+			}
+			if (tty->flip.char_buf_ptr != (char *) NULL) {
+				if (tty->flip.count < TTY_FLIPBUF_SIZE) {
+					*tty->flip.flag_buf_ptr++ = status;
+					*tty->flip.char_buf_ptr++ = ch;
+					tty->flip.count++;
+				}
+				tty_schedule_flip(tty);
+			}
+		}
+	} else {
+		printk("STALLION: bad RX interrupt ack value=%x\n", ioack);
+		return;
+	}
+
+stl_rxalldone:
+	outb((EOSRR + portp->uartaddr), ioaddr);
+	outb(0, (ioaddr + EREG_DATA));
+}
+
+/*****************************************************************************/
+
+/*
+ *	Modem interrupt handler. The is called when the modem signal line
+ *	(DCD) has changed state. Leave most of the work to the off-level
+ *	processing routine.
+ */
+
+static void stl_cd1400mdmisr(stlpanel_t *panelp, int ioaddr)
+{
+	stlport_t	*portp;
+	unsigned int	ioack;
+	unsigned char	misr;
+
+#ifdef DEBUG
+	printk("stl_cd1400mdmisr(panelp=%x)\n", (int) panelp);
+#endif
+
+	ioack = inb(ioaddr + EREG_MDACK);
+	if (((ioack & panelp->ackmask) != 0) ||
+	    ((ioack & ACK_TYPMASK) != ACK_TYPMDM)) {
+		printk("STALLION: bad MODEM interrupt ack value=%x\n", ioack);
+		return;
+	}
+	portp = panelp->ports[(ioack >> 3)];
+
+	outb((MISR + portp->uartaddr), ioaddr);
+	misr = inb(ioaddr + EREG_DATA);
+	if (misr & MISR_DCD) {
+		set_bit(ASYI_DCDCHANGE, &portp->istate);
+		schedule_work(&portp->tqueue);
+		portp->stats.modem++;
+	}
+
+	outb((EOSRR + portp->uartaddr), ioaddr);
+	outb(0, (ioaddr + EREG_DATA));
+}
+
+/*****************************************************************************/
+/*                      SC26198 HARDWARE FUNCTIONS                           */
+/*****************************************************************************/
+
+/*
+ *	These functions get/set/update the registers of the sc26198 UARTs.
+ *	Access to the sc26198 registers is via an address/data io port pair.
+ *	(Maybe should make this inline...)
+ */
+
+static int stl_sc26198getreg(stlport_t *portp, int regnr)
+{
+	outb((regnr | portp->uartaddr), (portp->ioaddr + XP_ADDR));
+	return(inb(portp->ioaddr + XP_DATA));
+}
+
+static void stl_sc26198setreg(stlport_t *portp, int regnr, int value)
+{
+	outb((regnr | portp->uartaddr), (portp->ioaddr + XP_ADDR));
+	outb(value, (portp->ioaddr + XP_DATA));
+}
+
+static int stl_sc26198updatereg(stlport_t *portp, int regnr, int value)
+{
+	outb((regnr | portp->uartaddr), (portp->ioaddr + XP_ADDR));
+	if (inb(portp->ioaddr + XP_DATA) != value) {
+		outb(value, (portp->ioaddr + XP_DATA));
+		return(1);
+	}
+	return(0);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Functions to get and set the sc26198 global registers.
+ */
+
+static int stl_sc26198getglobreg(stlport_t *portp, int regnr)
+{
+	outb(regnr, (portp->ioaddr + XP_ADDR));
+	return(inb(portp->ioaddr + XP_DATA));
+}
+
+#if 0
+static void stl_sc26198setglobreg(stlport_t *portp, int regnr, int value)
+{
+	outb(regnr, (portp->ioaddr + XP_ADDR));
+	outb(value, (portp->ioaddr + XP_DATA));
+}
+#endif
+
+/*****************************************************************************/
+
+/*
+ *	Inbitialize the UARTs in a panel. We don't care what sort of board
+ *	these ports are on - since the port io registers are almost
+ *	identical when dealing with ports.
+ */
+
+static int stl_sc26198panelinit(stlbrd_t *brdp, stlpanel_t *panelp)
+{
+	int	chipmask, i;
+	int	nrchips, ioaddr;
+
+#ifdef DEBUG
+	printk("stl_sc26198panelinit(brdp=%x,panelp=%x)\n",
+		(int) brdp, (int) panelp);
+#endif
+
+	BRDENABLE(panelp->brdnr, panelp->pagenr);
+
+/*
+ *	Check that each chip is present and started up OK.
+ */
+	chipmask = 0;
+	nrchips = (panelp->nrports + 4) / SC26198_PORTS;
+	if (brdp->brdtype == BRD_ECHPCI)
+		outb(panelp->pagenr, brdp->ioctrl);
+
+	for (i = 0; (i < nrchips); i++) {
+		ioaddr = panelp->iobase + (i * 4); 
+		outb(SCCR, (ioaddr + XP_ADDR));
+		outb(CR_RESETALL, (ioaddr + XP_DATA));
+		outb(TSTR, (ioaddr + XP_ADDR));
+		if (inb(ioaddr + XP_DATA) != 0) {
+			printk("STALLION: sc26198 not responding, "
+				"brd=%d panel=%d chip=%d\n",
+				panelp->brdnr, panelp->panelnr, i);
+			continue;
+		}
+		chipmask |= (0x1 << i);
+		outb(GCCR, (ioaddr + XP_ADDR));
+		outb(GCCR_IVRTYPCHANACK, (ioaddr + XP_DATA));
+		outb(WDTRCR, (ioaddr + XP_ADDR));
+		outb(0xff, (ioaddr + XP_DATA));
+	}
+
+	BRDDISABLE(panelp->brdnr);
+	return(chipmask);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Initialize hardware specific port registers.
+ */
+
+static void stl_sc26198portinit(stlbrd_t *brdp, stlpanel_t *panelp, stlport_t *portp)
+{
+#ifdef DEBUG
+	printk("stl_sc26198portinit(brdp=%x,panelp=%x,portp=%x)\n",
+		(int) brdp, (int) panelp, (int) portp);
+#endif
+
+	if ((brdp == (stlbrd_t *) NULL) || (panelp == (stlpanel_t *) NULL) ||
+	    (portp == (stlport_t *) NULL))
+		return;
+
+	portp->ioaddr = panelp->iobase + ((portp->portnr < 8) ? 0 : 4);
+	portp->uartaddr = (portp->portnr & 0x07) << 4;
+	portp->pagenr = panelp->pagenr;
+	portp->hwid = 0x1;
+
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_sc26198setreg(portp, IOPCR, IOPCR_SETSIGS);
+	BRDDISABLE(portp->brdnr);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Set up the sc26198 registers for a port based on the termios port
+ *	settings.
+ */
+
+static void stl_sc26198setport(stlport_t *portp, struct termios *tiosp)
+{
+	stlbrd_t	*brdp;
+	unsigned long	flags;
+	unsigned int	baudrate;
+	unsigned char	mr0, mr1, mr2, clk;
+	unsigned char	imron, imroff, iopr, ipr;
+
+	mr0 = 0;
+	mr1 = 0;
+	mr2 = 0;
+	clk = 0;
+	iopr = 0;
+	imron = 0;
+	imroff = 0;
+
+	brdp = stl_brds[portp->brdnr];
+	if (brdp == (stlbrd_t *) NULL)
+		return;
+
+/*
+ *	Set up the RX char ignore mask with those RX error types we
+ *	can ignore.
+ */
+	portp->rxignoremsk = 0;
+	if (tiosp->c_iflag & IGNPAR)
+		portp->rxignoremsk |= (SR_RXPARITY | SR_RXFRAMING |
+			SR_RXOVERRUN);
+	if (tiosp->c_iflag & IGNBRK)
+		portp->rxignoremsk |= SR_RXBREAK;
+
+	portp->rxmarkmsk = SR_RXOVERRUN;
+	if (tiosp->c_iflag & (INPCK | PARMRK))
+		portp->rxmarkmsk |= (SR_RXPARITY | SR_RXFRAMING);
+	if (tiosp->c_iflag & BRKINT)
+		portp->rxmarkmsk |= SR_RXBREAK;
+
+/*
+ *	Go through the char size, parity and stop bits and set all the
+ *	option register appropriately.
+ */
+	switch (tiosp->c_cflag & CSIZE) {
+	case CS5:
+		mr1 |= MR1_CS5;
+		break;
+	case CS6:
+		mr1 |= MR1_CS6;
+		break;
+	case CS7:
+		mr1 |= MR1_CS7;
+		break;
+	default:
+		mr1 |= MR1_CS8;
+		break;
+	}
+
+	if (tiosp->c_cflag & CSTOPB)
+		mr2 |= MR2_STOP2;
+	else
+		mr2 |= MR2_STOP1;
+
+	if (tiosp->c_cflag & PARENB) {
+		if (tiosp->c_cflag & PARODD)
+			mr1 |= (MR1_PARENB | MR1_PARODD);
+		else
+			mr1 |= (MR1_PARENB | MR1_PAREVEN);
+	} else {
+		mr1 |= MR1_PARNONE;
+	}
+
+	mr1 |= MR1_ERRBLOCK;
+
+/*
+ *	Set the RX FIFO threshold at 8 chars. This gives a bit of breathing
+ *	space for hardware flow control and the like. This should be set to
+ *	VMIN.
+ */
+	mr2 |= MR2_RXFIFOHALF;
+
+/*
+ *	Calculate the baud rate timers. For now we will just assume that
+ *	the input and output baud are the same. The sc26198 has a fixed
+ *	baud rate table, so only discrete baud rates possible.
+ */
+	baudrate = tiosp->c_cflag & CBAUD;
+	if (baudrate & CBAUDEX) {
+		baudrate &= ~CBAUDEX;
+		if ((baudrate < 1) || (baudrate > 4))
+			tiosp->c_cflag &= ~CBAUDEX;
+		else
+			baudrate += 15;
+	}
+	baudrate = stl_baudrates[baudrate];
+	if ((tiosp->c_cflag & CBAUD) == B38400) {
+		if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
+			baudrate = 57600;
+		else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
+			baudrate = 115200;
+		else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
+			baudrate = 230400;
+		else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
+			baudrate = 460800;
+		else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST)
+			baudrate = (portp->baud_base / portp->custom_divisor);
+	}
+	if (baudrate > STL_SC26198MAXBAUD)
+		baudrate = STL_SC26198MAXBAUD;
+
+	if (baudrate > 0) {
+		for (clk = 0; (clk < SC26198_NRBAUDS); clk++) {
+			if (baudrate <= sc26198_baudtable[clk])
+				break;
+		}
+	}
+
+/*
+ *	Check what form of modem signaling is required and set it up.
+ */
+	if (tiosp->c_cflag & CLOCAL) {
+		portp->flags &= ~ASYNC_CHECK_CD;
+	} else {
+		iopr |= IOPR_DCDCOS;
+		imron |= IR_IOPORT;
+		portp->flags |= ASYNC_CHECK_CD;
+	}
+
+/*
+ *	Setup sc26198 enhanced modes if we can. In particular we want to
+ *	handle as much of the flow control as possible automatically. As
+ *	well as saving a few CPU cycles it will also greatly improve flow
+ *	control reliability.
+ */
+	if (tiosp->c_iflag & IXON) {
+		mr0 |= MR0_SWFTX | MR0_SWFT;
+		imron |= IR_XONXOFF;
+	} else {
+		imroff |= IR_XONXOFF;
+	}
+	if (tiosp->c_iflag & IXOFF)
+		mr0 |= MR0_SWFRX;
+
+	if (tiosp->c_cflag & CRTSCTS) {
+		mr2 |= MR2_AUTOCTS;
+		mr1 |= MR1_AUTORTS;
+	}
+
+/*
+ *	All sc26198 register values calculated so go through and set
+ *	them all up.
+ */
+
+#ifdef DEBUG
+	printk("SETPORT: portnr=%d panelnr=%d brdnr=%d\n",
+		portp->portnr, portp->panelnr, portp->brdnr);
+	printk("    mr0=%x mr1=%x mr2=%x clk=%x\n", mr0, mr1, mr2, clk);
+	printk("    iopr=%x imron=%x imroff=%x\n", iopr, imron, imroff);
+	printk("    schr1=%x schr2=%x schr3=%x schr4=%x\n",
+		tiosp->c_cc[VSTART], tiosp->c_cc[VSTOP],
+		tiosp->c_cc[VSTART], tiosp->c_cc[VSTOP]);
+#endif
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_sc26198setreg(portp, IMR, 0);
+	stl_sc26198updatereg(portp, MR0, mr0);
+	stl_sc26198updatereg(portp, MR1, mr1);
+	stl_sc26198setreg(portp, SCCR, CR_RXERRBLOCK);
+	stl_sc26198updatereg(portp, MR2, mr2);
+	stl_sc26198updatereg(portp, IOPIOR,
+		((stl_sc26198getreg(portp, IOPIOR) & ~IPR_CHANGEMASK) | iopr));
+
+	if (baudrate > 0) {
+		stl_sc26198setreg(portp, TXCSR, clk);
+		stl_sc26198setreg(portp, RXCSR, clk);
+	}
+
+	stl_sc26198setreg(portp, XONCR, tiosp->c_cc[VSTART]);
+	stl_sc26198setreg(portp, XOFFCR, tiosp->c_cc[VSTOP]);
+
+	ipr = stl_sc26198getreg(portp, IPR);
+	if (ipr & IPR_DCD)
+		portp->sigs &= ~TIOCM_CD;
+	else
+		portp->sigs |= TIOCM_CD;
+
+	portp->imr = (portp->imr & ~imroff) | imron;
+	stl_sc26198setreg(portp, IMR, portp->imr);
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Set the state of the DTR and RTS signals.
+ */
+
+static void stl_sc26198setsignals(stlport_t *portp, int dtr, int rts)
+{
+	unsigned char	iopioron, iopioroff;
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_sc26198setsignals(portp=%x,dtr=%d,rts=%d)\n",
+		(int) portp, dtr, rts);
+#endif
+
+	iopioron = 0;
+	iopioroff = 0;
+	if (dtr == 0)
+		iopioroff |= IPR_DTR;
+	else if (dtr > 0)
+		iopioron |= IPR_DTR;
+	if (rts == 0)
+		iopioroff |= IPR_RTS;
+	else if (rts > 0)
+		iopioron |= IPR_RTS;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_sc26198setreg(portp, IOPIOR,
+		((stl_sc26198getreg(portp, IOPIOR) & ~iopioroff) | iopioron));
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Return the state of the signals.
+ */
+
+static int stl_sc26198getsignals(stlport_t *portp)
+{
+	unsigned char	ipr;
+	unsigned long	flags;
+	int		sigs;
+
+#ifdef DEBUG
+	printk("stl_sc26198getsignals(portp=%x)\n", (int) portp);
+#endif
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	ipr = stl_sc26198getreg(portp, IPR);
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+
+	sigs = 0;
+	sigs |= (ipr & IPR_DCD) ? 0 : TIOCM_CD;
+	sigs |= (ipr & IPR_CTS) ? 0 : TIOCM_CTS;
+	sigs |= (ipr & IPR_DTR) ? 0: TIOCM_DTR;
+	sigs |= (ipr & IPR_RTS) ? 0: TIOCM_RTS;
+	sigs |= TIOCM_DSR;
+	return(sigs);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Enable/Disable the Transmitter and/or Receiver.
+ */
+
+static void stl_sc26198enablerxtx(stlport_t *portp, int rx, int tx)
+{
+	unsigned char	ccr;
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_sc26198enablerxtx(portp=%x,rx=%d,tx=%d)\n",
+		(int) portp, rx, tx);
+#endif
+
+	ccr = portp->crenable;
+	if (tx == 0)
+		ccr &= ~CR_TXENABLE;
+	else if (tx > 0)
+		ccr |= CR_TXENABLE;
+	if (rx == 0)
+		ccr &= ~CR_RXENABLE;
+	else if (rx > 0)
+		ccr |= CR_RXENABLE;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_sc26198setreg(portp, SCCR, ccr);
+	BRDDISABLE(portp->brdnr);
+	portp->crenable = ccr;
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Start/stop the Transmitter and/or Receiver.
+ */
+
+static void stl_sc26198startrxtx(stlport_t *portp, int rx, int tx)
+{
+	unsigned char	imr;
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_sc26198startrxtx(portp=%x,rx=%d,tx=%d)\n",
+		(int) portp, rx, tx);
+#endif
+
+	imr = portp->imr;
+	if (tx == 0)
+		imr &= ~IR_TXRDY;
+	else if (tx == 1)
+		imr |= IR_TXRDY;
+	if (rx == 0)
+		imr &= ~(IR_RXRDY | IR_RXBREAK | IR_RXWATCHDOG);
+	else if (rx > 0)
+		imr |= IR_RXRDY | IR_RXBREAK | IR_RXWATCHDOG;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_sc26198setreg(portp, IMR, imr);
+	BRDDISABLE(portp->brdnr);
+	portp->imr = imr;
+	if (tx > 0)
+		set_bit(ASYI_TXBUSY, &portp->istate);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Disable all interrupts from this port.
+ */
+
+static void stl_sc26198disableintrs(stlport_t *portp)
+{
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_sc26198disableintrs(portp=%x)\n", (int) portp);
+#endif
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	portp->imr = 0;
+	stl_sc26198setreg(portp, IMR, 0);
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+static void stl_sc26198sendbreak(stlport_t *portp, int len)
+{
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_sc26198sendbreak(portp=%x,len=%d)\n", (int) portp, len);
+#endif
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	if (len == 1) {
+		stl_sc26198setreg(portp, SCCR, CR_TXSTARTBREAK);
+		portp->stats.txbreaks++;
+	} else {
+		stl_sc26198setreg(portp, SCCR, CR_TXSTOPBREAK);
+	}
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Take flow control actions...
+ */
+
+static void stl_sc26198flowctrl(stlport_t *portp, int state)
+{
+	struct tty_struct	*tty;
+	unsigned long		flags;
+	unsigned char		mr0;
+
+#ifdef DEBUG
+	printk("stl_sc26198flowctrl(portp=%x,state=%x)\n", (int) portp, state);
+#endif
+
+	if (portp == (stlport_t *) NULL)
+		return;
+	tty = portp->tty;
+	if (tty == (struct tty_struct *) NULL)
+		return;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+
+	if (state) {
+		if (tty->termios->c_iflag & IXOFF) {
+			mr0 = stl_sc26198getreg(portp, MR0);
+			stl_sc26198setreg(portp, MR0, (mr0 & ~MR0_SWFRXTX));
+			stl_sc26198setreg(portp, SCCR, CR_TXSENDXON);
+			mr0 |= MR0_SWFRX;
+			portp->stats.rxxon++;
+			stl_sc26198wait(portp);
+			stl_sc26198setreg(portp, MR0, mr0);
+		}
+/*
+ *		Question: should we return RTS to what it was before? It may
+ *		have been set by an ioctl... Suppose not, since if you have
+ *		hardware flow control set then it is pretty silly to go and
+ *		set the RTS line by hand.
+ */
+		if (tty->termios->c_cflag & CRTSCTS) {
+			stl_sc26198setreg(portp, MR1,
+				(stl_sc26198getreg(portp, MR1) | MR1_AUTORTS));
+			stl_sc26198setreg(portp, IOPIOR,
+				(stl_sc26198getreg(portp, IOPIOR) | IOPR_RTS));
+			portp->stats.rxrtson++;
+		}
+	} else {
+		if (tty->termios->c_iflag & IXOFF) {
+			mr0 = stl_sc26198getreg(portp, MR0);
+			stl_sc26198setreg(portp, MR0, (mr0 & ~MR0_SWFRXTX));
+			stl_sc26198setreg(portp, SCCR, CR_TXSENDXOFF);
+			mr0 &= ~MR0_SWFRX;
+			portp->stats.rxxoff++;
+			stl_sc26198wait(portp);
+			stl_sc26198setreg(portp, MR0, mr0);
+		}
+		if (tty->termios->c_cflag & CRTSCTS) {
+			stl_sc26198setreg(portp, MR1,
+				(stl_sc26198getreg(portp, MR1) & ~MR1_AUTORTS));
+			stl_sc26198setreg(portp, IOPIOR,
+				(stl_sc26198getreg(portp, IOPIOR) & ~IOPR_RTS));
+			portp->stats.rxrtsoff++;
+		}
+	}
+
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Send a flow control character.
+ */
+
+static void stl_sc26198sendflow(stlport_t *portp, int state)
+{
+	struct tty_struct	*tty;
+	unsigned long		flags;
+	unsigned char		mr0;
+
+#ifdef DEBUG
+	printk("stl_sc26198sendflow(portp=%x,state=%x)\n", (int) portp, state);
+#endif
+
+	if (portp == (stlport_t *) NULL)
+		return;
+	tty = portp->tty;
+	if (tty == (struct tty_struct *) NULL)
+		return;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	if (state) {
+		mr0 = stl_sc26198getreg(portp, MR0);
+		stl_sc26198setreg(portp, MR0, (mr0 & ~MR0_SWFRXTX));
+		stl_sc26198setreg(portp, SCCR, CR_TXSENDXON);
+		mr0 |= MR0_SWFRX;
+		portp->stats.rxxon++;
+		stl_sc26198wait(portp);
+		stl_sc26198setreg(portp, MR0, mr0);
+	} else {
+		mr0 = stl_sc26198getreg(portp, MR0);
+		stl_sc26198setreg(portp, MR0, (mr0 & ~MR0_SWFRXTX));
+		stl_sc26198setreg(portp, SCCR, CR_TXSENDXOFF);
+		mr0 &= ~MR0_SWFRX;
+		portp->stats.rxxoff++;
+		stl_sc26198wait(portp);
+		stl_sc26198setreg(portp, MR0, mr0);
+	}
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+static void stl_sc26198flush(stlport_t *portp)
+{
+	unsigned long	flags;
+
+#ifdef DEBUG
+	printk("stl_sc26198flush(portp=%x)\n", (int) portp);
+#endif
+
+	if (portp == (stlport_t *) NULL)
+		return;
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	stl_sc26198setreg(portp, SCCR, CR_TXRESET);
+	stl_sc26198setreg(portp, SCCR, portp->crenable);
+	BRDDISABLE(portp->brdnr);
+	portp->tx.tail = portp->tx.head;
+	restore_flags(flags);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Return the current state of data flow on this port. This is only
+ *	really interresting when determining if data has fully completed
+ *	transmission or not... The sc26198 interrupt scheme cannot
+ *	determine when all data has actually drained, so we need to
+ *	check the port statusy register to be sure.
+ */
+
+static int stl_sc26198datastate(stlport_t *portp)
+{
+	unsigned long	flags;
+	unsigned char	sr;
+
+#ifdef DEBUG
+	printk("stl_sc26198datastate(portp=%x)\n", (int) portp);
+#endif
+
+	if (portp == (stlport_t *) NULL)
+		return(0);
+	if (test_bit(ASYI_TXBUSY, &portp->istate))
+		return(1);
+
+	save_flags(flags);
+	cli();
+	BRDENABLE(portp->brdnr, portp->pagenr);
+	sr = stl_sc26198getreg(portp, SR);
+	BRDDISABLE(portp->brdnr);
+	restore_flags(flags);
+
+	return((sr & SR_TXEMPTY) ? 0 : 1);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Delay for a small amount of time, to give the sc26198 a chance
+ *	to process a command...
+ */
+
+static void stl_sc26198wait(stlport_t *portp)
+{
+	int	i;
+
+#ifdef DEBUG
+	printk("stl_sc26198wait(portp=%x)\n", (int) portp);
+#endif
+
+	if (portp == (stlport_t *) NULL)
+		return;
+
+	for (i = 0; (i < 20); i++)
+		stl_sc26198getglobreg(portp, TSTR);
+}
+
+/*****************************************************************************/
+
+/*
+ *	If we are TX flow controlled and in IXANY mode then we may
+ *	need to unflow control here. We gotta do this because of the
+ *	automatic flow control modes of the sc26198.
+ */
+
+static inline void stl_sc26198txunflow(stlport_t *portp, struct tty_struct *tty)
+{
+	unsigned char	mr0;
+
+	mr0 = stl_sc26198getreg(portp, MR0);
+	stl_sc26198setreg(portp, MR0, (mr0 & ~MR0_SWFRXTX));
+	stl_sc26198setreg(portp, SCCR, CR_HOSTXON);
+	stl_sc26198wait(portp);
+	stl_sc26198setreg(portp, MR0, mr0);
+	clear_bit(ASYI_TXFLOWED, &portp->istate);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Interrupt service routine for sc26198 panels.
+ */
+
+static void stl_sc26198intr(stlpanel_t *panelp, unsigned int iobase)
+{
+	stlport_t	*portp;
+	unsigned int	iack;
+
+/* 
+ *	Work around bug in sc26198 chip... Cannot have A6 address
+ *	line of UART high, else iack will be returned as 0.
+ */
+	outb(0, (iobase + 1));
+
+	iack = inb(iobase + XP_IACK);
+	portp = panelp->ports[(iack & IVR_CHANMASK) + ((iobase & 0x4) << 1)];
+
+	if (iack & IVR_RXDATA)
+		stl_sc26198rxisr(portp, iack);
+	else if (iack & IVR_TXDATA)
+		stl_sc26198txisr(portp);
+	else
+		stl_sc26198otherisr(portp, iack);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Transmit interrupt handler. This has gotta be fast!  Handling TX
+ *	chars is pretty simple, stuff as many as possible from the TX buffer
+ *	into the sc26198 FIFO.
+ *	In practice it is possible that interrupts are enabled but that the
+ *	port has been hung up. Need to handle not having any TX buffer here,
+ *	this is done by using the side effect that head and tail will also
+ *	be NULL if the buffer has been freed.
+ */
+
+static void stl_sc26198txisr(stlport_t *portp)
+{
+	unsigned int	ioaddr;
+	unsigned char	mr0;
+	int		len, stlen;
+	char		*head, *tail;
+
+#ifdef DEBUG
+	printk("stl_sc26198txisr(portp=%x)\n", (int) portp);
+#endif
+
+	ioaddr = portp->ioaddr;
+	head = portp->tx.head;
+	tail = portp->tx.tail;
+	len = (head >= tail) ? (head - tail) : (STL_TXBUFSIZE - (tail - head));
+	if ((len == 0) || ((len < STL_TXBUFLOW) &&
+	    (test_bit(ASYI_TXLOW, &portp->istate) == 0))) {
+		set_bit(ASYI_TXLOW, &portp->istate);
+		schedule_work(&portp->tqueue); 
+	}
+
+	if (len == 0) {
+		outb((MR0 | portp->uartaddr), (ioaddr + XP_ADDR));
+		mr0 = inb(ioaddr + XP_DATA);
+		if ((mr0 & MR0_TXMASK) == MR0_TXEMPTY) {
+			portp->imr &= ~IR_TXRDY;
+			outb((IMR | portp->uartaddr), (ioaddr + XP_ADDR));
+			outb(portp->imr, (ioaddr + XP_DATA));
+			clear_bit(ASYI_TXBUSY, &portp->istate);
+		} else {
+			mr0 |= ((mr0 & ~MR0_TXMASK) | MR0_TXEMPTY);
+			outb(mr0, (ioaddr + XP_DATA));
+		}
+	} else {
+		len = MIN(len, SC26198_TXFIFOSIZE);
+		portp->stats.txtotal += len;
+		stlen = MIN(len, ((portp->tx.buf + STL_TXBUFSIZE) - tail));
+		outb(GTXFIFO, (ioaddr + XP_ADDR));
+		outsb((ioaddr + XP_DATA), tail, stlen);
+		len -= stlen;
+		tail += stlen;
+		if (tail >= (portp->tx.buf + STL_TXBUFSIZE))
+			tail = portp->tx.buf;
+		if (len > 0) {
+			outsb((ioaddr + XP_DATA), tail, len);
+			tail += len;
+		}
+		portp->tx.tail = tail;
+	}
+}
+
+/*****************************************************************************/
+
+/*
+ *	Receive character interrupt handler. Determine if we have good chars
+ *	or bad chars and then process appropriately. Good chars are easy
+ *	just shove the lot into the RX buffer and set all status byte to 0.
+ *	If a bad RX char then process as required. This routine needs to be
+ *	fast!  In practice it is possible that we get an interrupt on a port
+ *	that is closed. This can happen on hangups - since they completely
+ *	shutdown a port not in user context. Need to handle this case.
+ */
+
+static void stl_sc26198rxisr(stlport_t *portp, unsigned int iack)
+{
+	struct tty_struct	*tty;
+	unsigned int		len, buflen, ioaddr;
+
+#ifdef DEBUG
+	printk("stl_sc26198rxisr(portp=%x,iack=%x)\n", (int) portp, iack);
+#endif
+
+	tty = portp->tty;
+	ioaddr = portp->ioaddr;
+	outb(GIBCR, (ioaddr + XP_ADDR));
+	len = inb(ioaddr + XP_DATA) + 1;
+
+	if ((iack & IVR_TYPEMASK) == IVR_RXDATA) {
+		if ((tty == (struct tty_struct *) NULL) ||
+		    (tty->flip.char_buf_ptr == (char *) NULL) ||
+		    ((buflen = TTY_FLIPBUF_SIZE - tty->flip.count) == 0)) {
+			len = MIN(len, sizeof(stl_unwanted));
+			outb(GRXFIFO, (ioaddr + XP_ADDR));
+			insb((ioaddr + XP_DATA), &stl_unwanted[0], len);
+			portp->stats.rxlost += len;
+			portp->stats.rxtotal += len;
+		} else {
+			len = MIN(len, buflen);
+			if (len > 0) {
+				outb(GRXFIFO, (ioaddr + XP_ADDR));
+				insb((ioaddr + XP_DATA), tty->flip.char_buf_ptr, len);
+				memset(tty->flip.flag_buf_ptr, 0, len);
+				tty->flip.flag_buf_ptr += len;
+				tty->flip.char_buf_ptr += len;
+				tty->flip.count += len;
+				tty_schedule_flip(tty);
+				portp->stats.rxtotal += len;
+			}
+		}
+	} else {
+		stl_sc26198rxbadchars(portp);
+	}
+
+/*
+ *	If we are TX flow controlled and in IXANY mode then we may need
+ *	to unflow control here. We gotta do this because of the automatic
+ *	flow control modes of the sc26198.
+ */
+	if (test_bit(ASYI_TXFLOWED, &portp->istate)) {
+		if ((tty != (struct tty_struct *) NULL) &&
+		    (tty->termios != (struct termios *) NULL) &&
+		    (tty->termios->c_iflag & IXANY)) {
+			stl_sc26198txunflow(portp, tty);
+		}
+	}
+}
+
+/*****************************************************************************/
+
+/*
+ *	Process an RX bad character.
+ */
+
+static inline void stl_sc26198rxbadch(stlport_t *portp, unsigned char status, char ch)
+{
+	struct tty_struct	*tty;
+	unsigned int		ioaddr;
+
+	tty = portp->tty;
+	ioaddr = portp->ioaddr;
+
+	if (status & SR_RXPARITY)
+		portp->stats.rxparity++;
+	if (status & SR_RXFRAMING)
+		portp->stats.rxframing++;
+	if (status & SR_RXOVERRUN)
+		portp->stats.rxoverrun++;
+	if (status & SR_RXBREAK)
+		portp->stats.rxbreaks++;
+
+	if ((tty != (struct tty_struct *) NULL) &&
+	    ((portp->rxignoremsk & status) == 0)) {
+		if (portp->rxmarkmsk & status) {
+			if (status & SR_RXBREAK) {
+				status = TTY_BREAK;
+				if (portp->flags & ASYNC_SAK) {
+					do_SAK(tty);
+					BRDENABLE(portp->brdnr, portp->pagenr);
+				}
+			} else if (status & SR_RXPARITY) {
+				status = TTY_PARITY;
+			} else if (status & SR_RXFRAMING) {
+				status = TTY_FRAME;
+			} else if(status & SR_RXOVERRUN) {
+				status = TTY_OVERRUN;
+			} else {
+				status = 0;
+			}
+		} else {
+			status = 0;
+		}
+
+		if (tty->flip.char_buf_ptr != (char *) NULL) {
+			if (tty->flip.count < TTY_FLIPBUF_SIZE) {
+				*tty->flip.flag_buf_ptr++ = status;
+				*tty->flip.char_buf_ptr++ = ch;
+				tty->flip.count++;
+			}
+			tty_schedule_flip(tty);
+		}
+
+		if (status == 0)
+			portp->stats.rxtotal++;
+	}
+}
+
+/*****************************************************************************/
+
+/*
+ *	Process all characters in the RX FIFO of the UART. Check all char
+ *	status bytes as well, and process as required. We need to check
+ *	all bytes in the FIFO, in case some more enter the FIFO while we
+ *	are here. To get the exact character error type we need to switch
+ *	into CHAR error mode (that is why we need to make sure we empty
+ *	the FIFO).
+ */
+
+static void stl_sc26198rxbadchars(stlport_t *portp)
+{
+	unsigned char	status, mr1;
+	char		ch;
+
+/*
+ *	To get the precise error type for each character we must switch
+ *	back into CHAR error mode.
+ */
+	mr1 = stl_sc26198getreg(portp, MR1);
+	stl_sc26198setreg(portp, MR1, (mr1 & ~MR1_ERRBLOCK));
+
+	while ((status = stl_sc26198getreg(portp, SR)) & SR_RXRDY) {
+		stl_sc26198setreg(portp, SCCR, CR_CLEARRXERR);
+		ch = stl_sc26198getreg(portp, RXFIFO);
+		stl_sc26198rxbadch(portp, status, ch);
+	}
+
+/*
+ *	To get correct interrupt class we must switch back into BLOCK
+ *	error mode.
+ */
+	stl_sc26198setreg(portp, MR1, mr1);
+}
+
+/*****************************************************************************/
+
+/*
+ *	Other interrupt handler. This includes modem signals, flow
+ *	control actions, etc. Most stuff is left to off-level interrupt
+ *	processing time.
+ */
+
+static void stl_sc26198otherisr(stlport_t *portp, unsigned int iack)
+{
+	unsigned char	cir, ipr, xisr;
+
+#ifdef DEBUG
+	printk("stl_sc26198otherisr(portp=%x,iack=%x)\n", (int) portp, iack);
+#endif
+
+	cir = stl_sc26198getglobreg(portp, CIR);
+
+	switch (cir & CIR_SUBTYPEMASK) {
+	case CIR_SUBCOS:
+		ipr = stl_sc26198getreg(portp, IPR);
+		if (ipr & IPR_DCDCHANGE) {
+			set_bit(ASYI_DCDCHANGE, &portp->istate);
+			schedule_work(&portp->tqueue); 
+			portp->stats.modem++;
+		}
+		break;
+	case CIR_SUBXONXOFF:
+		xisr = stl_sc26198getreg(portp, XISR);
+		if (xisr & XISR_RXXONGOT) {
+			set_bit(ASYI_TXFLOWED, &portp->istate);
+			portp->stats.txxoff++;
+		}
+		if (xisr & XISR_RXXOFFGOT) {
+			clear_bit(ASYI_TXFLOWED, &portp->istate);
+			portp->stats.txxon++;
+		}
+		break;
+	case CIR_SUBBREAK:
+		stl_sc26198setreg(portp, SCCR, CR_BREAKRESET);
+		stl_sc26198rxbadchars(portp);
+		break;
+	default:
+		break;
+	}
+}
+
+/*****************************************************************************/