diff --git a/drivers/ieee1394/sbp2.c b/drivers/ieee1394/sbp2.c
new file mode 100644
index 0000000..00c7b95
--- /dev/null
+++ b/drivers/ieee1394/sbp2.c
@@ -0,0 +1,2864 @@
+/*
+ * sbp2.c - SBP-2 protocol driver for IEEE-1394
+ *
+ * Copyright (C) 2000 James Goodwin, Filanet Corporation (www.filanet.com)
+ * jamesg@filanet.com (JSG)
+ *
+ * Copyright (C) 2003 Ben Collins <bcollins@debian.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software Foundation,
+ * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+/*
+ * Brief Description:
+ *
+ * This driver implements the Serial Bus Protocol 2 (SBP-2) over IEEE-1394
+ * under Linux. The SBP-2 driver is implemented as an IEEE-1394 high-level
+ * driver. It also registers as a SCSI lower-level driver in order to accept
+ * SCSI commands for transport using SBP-2.
+ *
+ * You may access any attached SBP-2 storage devices as if they were SCSI
+ * devices (e.g. mount /dev/sda1,  fdisk, mkfs, etc.).
+ *
+ * Current Issues:
+ *
+ *	- Error Handling: SCSI aborts and bus reset requests are handled somewhat
+ *	  but the code needs additional debugging.
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/string.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/fs.h>
+#include <linux/poll.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/types.h>
+#include <linux/delay.h>
+#include <linux/sched.h>
+#include <linux/blkdev.h>
+#include <linux/smp_lock.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+
+#include <asm/current.h>
+#include <asm/uaccess.h>
+#include <asm/io.h>
+#include <asm/byteorder.h>
+#include <asm/atomic.h>
+#include <asm/system.h>
+#include <asm/scatterlist.h>
+
+#include <scsi/scsi.h>
+#include <scsi/scsi_cmnd.h>
+#include <scsi/scsi_dbg.h>
+#include <scsi/scsi_device.h>
+#include <scsi/scsi_host.h>
+
+#include "csr1212.h"
+#include "ieee1394.h"
+#include "ieee1394_types.h"
+#include "ieee1394_core.h"
+#include "nodemgr.h"
+#include "hosts.h"
+#include "highlevel.h"
+#include "ieee1394_transactions.h"
+#include "sbp2.h"
+
+static char version[] __devinitdata =
+	"$Rev: 1219 $ Ben Collins <bcollins@debian.org>";
+
+/*
+ * Module load parameter definitions
+ */
+
+/*
+ * Change max_speed on module load if you have a bad IEEE-1394
+ * controller that has trouble running 2KB packets at 400mb.
+ *
+ * NOTE: On certain OHCI parts I have seen short packets on async transmit
+ * (probably due to PCI latency/throughput issues with the part). You can
+ * bump down the speed if you are running into problems.
+ */
+static int max_speed = IEEE1394_SPEED_MAX;
+module_param(max_speed, int, 0644);
+MODULE_PARM_DESC(max_speed, "Force max speed (3 = 800mb, 2 = 400mb default, 1 = 200mb, 0 = 100mb)");
+
+/*
+ * Set serialize_io to 1 if you'd like only one scsi command sent
+ * down to us at a time (debugging). This might be necessary for very
+ * badly behaved sbp2 devices.
+ */
+static int serialize_io = 0;
+module_param(serialize_io, int, 0444);
+MODULE_PARM_DESC(serialize_io, "Serialize all I/O coming down from the scsi drivers (default = 0)");
+
+/*
+ * Bump up max_sectors if you'd like to support very large sized
+ * transfers. Please note that some older sbp2 bridge chips are broken for
+ * transfers greater or equal to 128KB.  Default is a value of 255
+ * sectors, or just under 128KB (at 512 byte sector size). I can note that
+ * the Oxsemi sbp2 chipsets have no problems supporting very large
+ * transfer sizes.
+ */
+static int max_sectors = SBP2_MAX_SECTORS;
+module_param(max_sectors, int, 0444);
+MODULE_PARM_DESC(max_sectors, "Change max sectors per I/O supported (default = 255)");
+
+/*
+ * Exclusive login to sbp2 device? In most cases, the sbp2 driver should
+ * do an exclusive login, as it's generally unsafe to have two hosts
+ * talking to a single sbp2 device at the same time (filesystem coherency,
+ * etc.). If you're running an sbp2 device that supports multiple logins,
+ * and you're either running read-only filesystems or some sort of special
+ * filesystem supporting multiple hosts (one such filesystem is OpenGFS,
+ * see opengfs.sourceforge.net for more info), then set exclusive_login
+ * to zero. Note: The Oxsemi OXFW911 sbp2 chipset supports up to four
+ * concurrent logins.
+ */
+static int exclusive_login = 1;
+module_param(exclusive_login, int, 0644);
+MODULE_PARM_DESC(exclusive_login, "Exclusive login to sbp2 device (default = 1)");
+
+/*
+ * SCSI inquiry hack for really badly behaved sbp2 devices. Turn this on
+ * if your sbp2 device is not properly handling the SCSI inquiry command.
+ * This hack makes the inquiry look more like a typical MS Windows
+ * inquiry.
+ *
+ * If force_inquiry_hack=1 is required for your device to work,
+ * please submit the logged sbp2_firmware_revision value of this device to
+ * the linux1394-devel mailing list.
+ */
+static int force_inquiry_hack = 0;
+module_param(force_inquiry_hack, int, 0444);
+MODULE_PARM_DESC(force_inquiry_hack, "Force SCSI inquiry hack (default = 0)");
+
+
+/*
+ * Export information about protocols/devices supported by this driver.
+ */
+static struct ieee1394_device_id sbp2_id_table[] = {
+	{
+		.match_flags =IEEE1394_MATCH_SPECIFIER_ID |
+		              IEEE1394_MATCH_VERSION,
+		.specifier_id = SBP2_UNIT_SPEC_ID_ENTRY & 0xffffff,
+		.version =    SBP2_SW_VERSION_ENTRY & 0xffffff
+	},
+	{ }
+};
+
+MODULE_DEVICE_TABLE(ieee1394, sbp2_id_table);
+
+/*
+ * Debug levels, configured via kernel config, or enable here.
+ */
+
+/* #define CONFIG_IEEE1394_SBP2_DEBUG_ORBS */
+/* #define CONFIG_IEEE1394_SBP2_DEBUG_DMA */
+/* #define CONFIG_IEEE1394_SBP2_DEBUG 1 */
+/* #define CONFIG_IEEE1394_SBP2_DEBUG 2 */
+/* #define CONFIG_IEEE1394_SBP2_PACKET_DUMP */
+
+#ifdef CONFIG_IEEE1394_SBP2_DEBUG_ORBS
+#define SBP2_ORB_DEBUG(fmt, args...)	HPSB_ERR("sbp2(%s): "fmt, __FUNCTION__, ## args)
+static u32 global_outstanding_command_orbs = 0;
+#define outstanding_orb_incr global_outstanding_command_orbs++
+#define outstanding_orb_decr global_outstanding_command_orbs--
+#else
+#define SBP2_ORB_DEBUG(fmt, args...)
+#define outstanding_orb_incr
+#define outstanding_orb_decr
+#endif
+
+#ifdef CONFIG_IEEE1394_SBP2_DEBUG_DMA
+#define SBP2_DMA_ALLOC(fmt, args...) \
+	HPSB_ERR("sbp2(%s)alloc(%d): "fmt, __FUNCTION__, \
+		 ++global_outstanding_dmas, ## args)
+#define SBP2_DMA_FREE(fmt, args...) \
+	HPSB_ERR("sbp2(%s)free(%d): "fmt, __FUNCTION__, \
+		 --global_outstanding_dmas, ## args)
+static u32 global_outstanding_dmas = 0;
+#else
+#define SBP2_DMA_ALLOC(fmt, args...)
+#define SBP2_DMA_FREE(fmt, args...)
+#endif
+
+#if CONFIG_IEEE1394_SBP2_DEBUG >= 2
+#define SBP2_DEBUG(fmt, args...)	HPSB_ERR("sbp2: "fmt, ## args)
+#define SBP2_INFO(fmt, args...)		HPSB_ERR("sbp2: "fmt, ## args)
+#define SBP2_NOTICE(fmt, args...)	HPSB_ERR("sbp2: "fmt, ## args)
+#define SBP2_WARN(fmt, args...)		HPSB_ERR("sbp2: "fmt, ## args)
+#elif CONFIG_IEEE1394_SBP2_DEBUG == 1
+#define SBP2_DEBUG(fmt, args...)	HPSB_DEBUG("sbp2: "fmt, ## args)
+#define SBP2_INFO(fmt, args...)		HPSB_INFO("sbp2: "fmt, ## args)
+#define SBP2_NOTICE(fmt, args...)	HPSB_NOTICE("sbp2: "fmt, ## args)
+#define SBP2_WARN(fmt, args...)		HPSB_WARN("sbp2: "fmt, ## args)
+#else
+#define SBP2_DEBUG(fmt, args...)
+#define SBP2_INFO(fmt, args...)		HPSB_INFO("sbp2: "fmt, ## args)
+#define SBP2_NOTICE(fmt, args...)       HPSB_NOTICE("sbp2: "fmt, ## args)
+#define SBP2_WARN(fmt, args...)         HPSB_WARN("sbp2: "fmt, ## args)
+#endif
+
+#define SBP2_ERR(fmt, args...)		HPSB_ERR("sbp2: "fmt, ## args)
+
+
+/*
+ * Globals
+ */
+
+static void sbp2scsi_complete_all_commands(struct scsi_id_instance_data *scsi_id,
+					   u32 status);
+
+static void sbp2scsi_complete_command(struct scsi_id_instance_data *scsi_id,
+				      u32 scsi_status, struct scsi_cmnd *SCpnt,
+				      void (*done)(struct scsi_cmnd *));
+
+static struct scsi_host_template scsi_driver_template;
+
+static const u8 sbp2_speedto_max_payload[] = { 0x7, 0x8, 0x9, 0xA, 0xB, 0xC };
+
+static void sbp2_host_reset(struct hpsb_host *host);
+
+static int sbp2_probe(struct device *dev);
+static int sbp2_remove(struct device *dev);
+static int sbp2_update(struct unit_directory *ud);
+
+static struct hpsb_highlevel sbp2_highlevel = {
+	.name =		SBP2_DEVICE_NAME,
+	.host_reset =	sbp2_host_reset,
+};
+
+static struct hpsb_address_ops sbp2_ops = {
+	.write = sbp2_handle_status_write
+};
+
+#ifdef CONFIG_IEEE1394_SBP2_PHYS_DMA
+static struct hpsb_address_ops sbp2_physdma_ops = {
+        .read = sbp2_handle_physdma_read,
+        .write = sbp2_handle_physdma_write,
+};
+#endif
+
+static struct hpsb_protocol_driver sbp2_driver = {
+	.name		= "SBP2 Driver",
+	.id_table	= sbp2_id_table,
+	.update		= sbp2_update,
+	.driver		= {
+		.name		= SBP2_DEVICE_NAME,
+		.bus		= &ieee1394_bus_type,
+		.probe		= sbp2_probe,
+		.remove		= sbp2_remove,
+	},
+};
+
+
+/* List of device firmware's that require a forced 36 byte inquiry.  */
+static u32 sbp2_broken_inquiry_list[] = {
+	0x00002800,	/* Stefan Richter <richtest@bauwesen.tu-cottbus.de> */
+			/* DViCO Momobay CX-1 */
+	0x00000200	/* Andreas Plesch <plesch@fas.harvard.edu> */
+			/* QPS Fire DVDBurner */
+};
+
+#define NUM_BROKEN_INQUIRY_DEVS \
+	(sizeof(sbp2_broken_inquiry_list)/sizeof(*sbp2_broken_inquiry_list))
+
+/**************************************
+ * General utility functions
+ **************************************/
+
+
+#ifndef __BIG_ENDIAN
+/*
+ * Converts a buffer from be32 to cpu byte ordering. Length is in bytes.
+ */
+static __inline__ void sbp2util_be32_to_cpu_buffer(void *buffer, int length)
+{
+	u32 *temp = buffer;
+
+	for (length = (length >> 2); length--; )
+		temp[length] = be32_to_cpu(temp[length]);
+
+	return;
+}
+
+/*
+ * Converts a buffer from cpu to be32 byte ordering. Length is in bytes.
+ */
+static __inline__ void sbp2util_cpu_to_be32_buffer(void *buffer, int length)
+{
+	u32 *temp = buffer;
+
+	for (length = (length >> 2); length--; )
+		temp[length] = cpu_to_be32(temp[length]);
+
+	return;
+}
+#else /* BIG_ENDIAN */
+/* Why waste the cpu cycles? */
+#define sbp2util_be32_to_cpu_buffer(x,y)
+#define sbp2util_cpu_to_be32_buffer(x,y)
+#endif
+
+#ifdef CONFIG_IEEE1394_SBP2_PACKET_DUMP
+/*
+ * Debug packet dump routine. Length is in bytes.
+ */
+static void sbp2util_packet_dump(void *buffer, int length, char *dump_name, u32 dump_phys_addr)
+{
+	int i;
+	unsigned char *dump = buffer;
+
+	if (!dump || !length || !dump_name)
+		return;
+
+	if (dump_phys_addr)
+		printk("[%s, 0x%x]", dump_name, dump_phys_addr);
+	else
+		printk("[%s]", dump_name);
+	for (i = 0; i < length; i++) {
+		if (i > 0x3f) {
+			printk("\n   ...");
+			break;
+		}
+		if ((i & 0x3) == 0)
+			printk("  ");
+		if ((i & 0xf) == 0)
+			printk("\n   ");
+		printk("%02x ", (int) dump[i]);
+	}
+	printk("\n");
+
+	return;
+}
+#else
+#define sbp2util_packet_dump(w,x,y,z)
+#endif
+
+/*
+ * Goofy routine that basically does a down_timeout function.
+ */
+static int sbp2util_down_timeout(atomic_t *done, int timeout)
+{
+	int i;
+
+	for (i = timeout; (i > 0 && atomic_read(done) == 0); i-= HZ/10) {
+		if (msleep_interruptible(100))	/* 100ms */
+			return(1);
+	}
+	return ((i > 0) ? 0:1);
+}
+
+/* Free's an allocated packet */
+static void sbp2_free_packet(struct hpsb_packet *packet)
+{
+	hpsb_free_tlabel(packet);
+	hpsb_free_packet(packet);
+}
+
+/* This is much like hpsb_node_write(), except it ignores the response
+ * subaction and returns immediately. Can be used from interrupts.
+ */
+static int sbp2util_node_write_no_wait(struct node_entry *ne, u64 addr,
+				quadlet_t *buffer, size_t length)
+{
+	struct hpsb_packet *packet;
+
+	packet = hpsb_make_writepacket(ne->host, ne->nodeid,
+				       addr, buffer, length);
+        if (!packet)
+                return -ENOMEM;
+
+	hpsb_set_packet_complete_task(packet, (void (*)(void*))sbp2_free_packet,
+				      packet);
+
+	hpsb_node_fill_packet(ne, packet);
+
+        if (hpsb_send_packet(packet) < 0) {
+		sbp2_free_packet(packet);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+/*
+ * This function is called to create a pool of command orbs used for
+ * command processing. It is called when a new sbp2 device is detected.
+ */
+static int sbp2util_create_command_orb_pool(struct scsi_id_instance_data *scsi_id)
+{
+	struct sbp2scsi_host_info *hi = scsi_id->hi;
+	int i;
+	unsigned long flags, orbs;
+	struct sbp2_command_info *command;
+
+	orbs = serialize_io ? 2 : SBP2_MAX_CMDS;
+
+	spin_lock_irqsave(&scsi_id->sbp2_command_orb_lock, flags);
+	for (i = 0; i < orbs; i++) {
+		command = (struct sbp2_command_info *)
+		    kmalloc(sizeof(struct sbp2_command_info), GFP_ATOMIC);
+		if (!command) {
+			spin_unlock_irqrestore(&scsi_id->sbp2_command_orb_lock, flags);
+			return(-ENOMEM);
+		}
+		memset(command, '\0', sizeof(struct sbp2_command_info));
+		command->command_orb_dma =
+			pci_map_single (hi->host->pdev, &command->command_orb,
+					sizeof(struct sbp2_command_orb),
+					PCI_DMA_BIDIRECTIONAL);
+		SBP2_DMA_ALLOC("single command orb DMA");
+		command->sge_dma =
+			pci_map_single (hi->host->pdev, &command->scatter_gather_element,
+					sizeof(command->scatter_gather_element),
+					PCI_DMA_BIDIRECTIONAL);
+		SBP2_DMA_ALLOC("scatter_gather_element");
+		INIT_LIST_HEAD(&command->list);
+		list_add_tail(&command->list, &scsi_id->sbp2_command_orb_completed);
+	}
+	spin_unlock_irqrestore(&scsi_id->sbp2_command_orb_lock, flags);
+	return 0;
+}
+
+/*
+ * This function is called to delete a pool of command orbs.
+ */
+static void sbp2util_remove_command_orb_pool(struct scsi_id_instance_data *scsi_id)
+{
+	struct hpsb_host *host = scsi_id->hi->host;
+	struct list_head *lh, *next;
+	struct sbp2_command_info *command;
+	unsigned long flags;
+
+	spin_lock_irqsave(&scsi_id->sbp2_command_orb_lock, flags);
+	if (!list_empty(&scsi_id->sbp2_command_orb_completed)) {
+		list_for_each_safe(lh, next, &scsi_id->sbp2_command_orb_completed) {
+			command = list_entry(lh, struct sbp2_command_info, list);
+
+			/* Release our generic DMA's */
+			pci_unmap_single(host->pdev, command->command_orb_dma,
+					 sizeof(struct sbp2_command_orb),
+					 PCI_DMA_BIDIRECTIONAL);
+			SBP2_DMA_FREE("single command orb DMA");
+			pci_unmap_single(host->pdev, command->sge_dma,
+					 sizeof(command->scatter_gather_element),
+					 PCI_DMA_BIDIRECTIONAL);
+			SBP2_DMA_FREE("scatter_gather_element");
+
+			kfree(command);
+		}
+	}
+	spin_unlock_irqrestore(&scsi_id->sbp2_command_orb_lock, flags);
+	return;
+}
+
+/*
+ * This function finds the sbp2_command for a given outstanding command
+ * orb.Only looks at the inuse list.
+ */
+static struct sbp2_command_info *sbp2util_find_command_for_orb(
+		struct scsi_id_instance_data *scsi_id, dma_addr_t orb)
+{
+	struct sbp2_command_info *command;
+	unsigned long flags;
+
+	spin_lock_irqsave(&scsi_id->sbp2_command_orb_lock, flags);
+	if (!list_empty(&scsi_id->sbp2_command_orb_inuse)) {
+		list_for_each_entry(command, &scsi_id->sbp2_command_orb_inuse, list) {
+			if (command->command_orb_dma == orb) {
+				spin_unlock_irqrestore(&scsi_id->sbp2_command_orb_lock, flags);
+				return (command);
+			}
+		}
+	}
+	spin_unlock_irqrestore(&scsi_id->sbp2_command_orb_lock, flags);
+
+	SBP2_ORB_DEBUG("could not match command orb %x", (unsigned int)orb);
+
+	return(NULL);
+}
+
+/*
+ * This function finds the sbp2_command for a given outstanding SCpnt.
+ * Only looks at the inuse list.
+ */
+static struct sbp2_command_info *sbp2util_find_command_for_SCpnt(struct scsi_id_instance_data *scsi_id, void *SCpnt)
+{
+	struct sbp2_command_info *command;
+	unsigned long flags;
+
+	spin_lock_irqsave(&scsi_id->sbp2_command_orb_lock, flags);
+	if (!list_empty(&scsi_id->sbp2_command_orb_inuse)) {
+		list_for_each_entry(command, &scsi_id->sbp2_command_orb_inuse, list) {
+			if (command->Current_SCpnt == SCpnt) {
+				spin_unlock_irqrestore(&scsi_id->sbp2_command_orb_lock, flags);
+				return (command);
+			}
+		}
+	}
+	spin_unlock_irqrestore(&scsi_id->sbp2_command_orb_lock, flags);
+	return(NULL);
+}
+
+/*
+ * This function allocates a command orb used to send a scsi command.
+ */
+static struct sbp2_command_info *sbp2util_allocate_command_orb(
+		struct scsi_id_instance_data *scsi_id,
+		struct scsi_cmnd *Current_SCpnt,
+		void (*Current_done)(struct scsi_cmnd *))
+{
+	struct list_head *lh;
+	struct sbp2_command_info *command = NULL;
+	unsigned long flags;
+
+	spin_lock_irqsave(&scsi_id->sbp2_command_orb_lock, flags);
+	if (!list_empty(&scsi_id->sbp2_command_orb_completed)) {
+		lh = scsi_id->sbp2_command_orb_completed.next;
+		list_del(lh);
+		command = list_entry(lh, struct sbp2_command_info, list);
+		command->Current_done = Current_done;
+		command->Current_SCpnt = Current_SCpnt;
+		list_add_tail(&command->list, &scsi_id->sbp2_command_orb_inuse);
+	} else {
+		SBP2_ERR("sbp2util_allocate_command_orb - No orbs available!");
+	}
+	spin_unlock_irqrestore(&scsi_id->sbp2_command_orb_lock, flags);
+	return (command);
+}
+
+/* Free our DMA's */
+static void sbp2util_free_command_dma(struct sbp2_command_info *command)
+{
+	struct scsi_id_instance_data *scsi_id =
+		(struct scsi_id_instance_data *)command->Current_SCpnt->device->host->hostdata[0];
+	struct hpsb_host *host;
+
+	if (!scsi_id) {
+		printk(KERN_ERR "%s: scsi_id == NULL\n", __FUNCTION__);
+		return;
+	}
+
+	host = scsi_id->ud->ne->host;
+
+	if (command->cmd_dma) {
+		if (command->dma_type == CMD_DMA_SINGLE) {
+			pci_unmap_single(host->pdev, command->cmd_dma,
+					 command->dma_size, command->dma_dir);
+			SBP2_DMA_FREE("single bulk");
+		} else if (command->dma_type == CMD_DMA_PAGE) {
+			pci_unmap_page(host->pdev, command->cmd_dma,
+				       command->dma_size, command->dma_dir);
+			SBP2_DMA_FREE("single page");
+		} /* XXX: Check for CMD_DMA_NONE bug */
+		command->dma_type = CMD_DMA_NONE;
+		command->cmd_dma = 0;
+	}
+
+	if (command->sge_buffer) {
+		pci_unmap_sg(host->pdev, command->sge_buffer,
+			     command->dma_size, command->dma_dir);
+		SBP2_DMA_FREE("scatter list");
+		command->sge_buffer = NULL;
+	}
+}
+
+/*
+ * This function moves a command to the completed orb list.
+ */
+static void sbp2util_mark_command_completed(struct scsi_id_instance_data *scsi_id, struct sbp2_command_info *command)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&scsi_id->sbp2_command_orb_lock, flags);
+	list_del(&command->list);
+	sbp2util_free_command_dma(command);
+	list_add_tail(&command->list, &scsi_id->sbp2_command_orb_completed);
+	spin_unlock_irqrestore(&scsi_id->sbp2_command_orb_lock, flags);
+}
+
+
+
+/*********************************************
+ * IEEE-1394 core driver stack related section
+ *********************************************/
+static struct scsi_id_instance_data *sbp2_alloc_device(struct unit_directory *ud);
+
+static int sbp2_probe(struct device *dev)
+{
+	struct unit_directory *ud;
+	struct scsi_id_instance_data *scsi_id;
+
+	SBP2_DEBUG("sbp2_probe");
+
+	ud = container_of(dev, struct unit_directory, device);
+
+	/* Don't probe UD's that have the LUN flag. We'll probe the LUN(s)
+	 * instead. */
+	if (ud->flags & UNIT_DIRECTORY_HAS_LUN_DIRECTORY)
+		return -ENODEV;
+
+        scsi_id = sbp2_alloc_device(ud);
+
+        if (!scsi_id)
+                return -ENOMEM;
+
+        sbp2_parse_unit_directory(scsi_id, ud);
+
+        return sbp2_start_device(scsi_id);
+}
+
+static int sbp2_remove(struct device *dev)
+{
+	struct unit_directory *ud;
+	struct scsi_id_instance_data *scsi_id;
+
+	SBP2_DEBUG("sbp2_remove");
+
+	ud = container_of(dev, struct unit_directory, device);
+	scsi_id = ud->device.driver_data;
+
+	sbp2_logout_device(scsi_id);
+	sbp2_remove_device(scsi_id);
+
+	return 0;
+}
+
+static int sbp2_update(struct unit_directory *ud)
+{
+	struct scsi_id_instance_data *scsi_id = ud->device.driver_data;
+
+	SBP2_DEBUG("sbp2_update");
+
+	if (sbp2_reconnect_device(scsi_id)) {
+
+		/*
+		 * Ok, reconnect has failed. Perhaps we didn't
+		 * reconnect fast enough. Try doing a regular login, but
+		 * first do a logout just in case of any weirdness.
+		 */
+		sbp2_logout_device(scsi_id);
+
+		if (sbp2_login_device(scsi_id)) {
+			/* Login failed too, just fail, and the backend
+			 * will call our sbp2_remove for us */
+			SBP2_ERR("Failed to reconnect to sbp2 device!");
+			return -EBUSY;
+		}
+	}
+
+	/* Set max retries to something large on the device. */
+	sbp2_set_busy_timeout(scsi_id);
+
+	/* Do a SBP-2 fetch agent reset. */
+	sbp2_agent_reset(scsi_id, 1);
+
+	/* Get the max speed and packet size that we can use. */
+	sbp2_max_speed_and_size(scsi_id);
+
+	/* Complete any pending commands with busy (so they get
+	 * retried) and remove them from our queue
+	 */
+	sbp2scsi_complete_all_commands(scsi_id, DID_BUS_BUSY);
+
+	/* Make sure we unblock requests (since this is likely after a bus
+	 * reset). */
+	scsi_unblock_requests(scsi_id->scsi_host);
+
+	return 0;
+}
+
+/* This functions is called by the sbp2_probe, for each new device. We now
+ * allocate one scsi host for each scsi_id (unit directory). */
+static struct scsi_id_instance_data *sbp2_alloc_device(struct unit_directory *ud)
+{
+	struct sbp2scsi_host_info *hi;
+	struct Scsi_Host *scsi_host = NULL;
+	struct scsi_id_instance_data *scsi_id = NULL;
+
+	SBP2_DEBUG("sbp2_alloc_device");
+
+	scsi_id = kmalloc(sizeof(*scsi_id), GFP_KERNEL);
+	if (!scsi_id) {
+		SBP2_ERR("failed to create scsi_id");
+		goto failed_alloc;
+	}
+	memset(scsi_id, 0, sizeof(*scsi_id));
+
+	scsi_id->ne = ud->ne;
+	scsi_id->ud = ud;
+	scsi_id->speed_code = IEEE1394_SPEED_100;
+	scsi_id->max_payload_size = sbp2_speedto_max_payload[IEEE1394_SPEED_100];
+	atomic_set(&scsi_id->sbp2_login_complete, 0);
+	INIT_LIST_HEAD(&scsi_id->sbp2_command_orb_inuse);
+	INIT_LIST_HEAD(&scsi_id->sbp2_command_orb_completed);
+	INIT_LIST_HEAD(&scsi_id->scsi_list);
+	spin_lock_init(&scsi_id->sbp2_command_orb_lock);
+	scsi_id->sbp2_device_type_and_lun = SBP2_DEVICE_TYPE_LUN_UNINITIALIZED;
+
+	ud->device.driver_data = scsi_id;
+
+	hi = hpsb_get_hostinfo(&sbp2_highlevel, ud->ne->host);
+	if (!hi) {
+		hi = hpsb_create_hostinfo(&sbp2_highlevel, ud->ne->host, sizeof(*hi));
+		if (!hi) {
+			SBP2_ERR("failed to allocate hostinfo");
+			goto failed_alloc;
+		}
+		SBP2_DEBUG("sbp2_alloc_device: allocated hostinfo");
+		hi->host = ud->ne->host;
+		INIT_LIST_HEAD(&hi->scsi_ids);
+
+		/* Register our sbp2 status address space... */
+		hpsb_register_addrspace(&sbp2_highlevel, ud->ne->host, &sbp2_ops,
+					SBP2_STATUS_FIFO_ADDRESS,
+					SBP2_STATUS_FIFO_ADDRESS +
+					SBP2_STATUS_FIFO_ENTRY_TO_OFFSET(SBP2_MAX_UDS_PER_NODE+1));
+#ifdef CONFIG_IEEE1394_SBP2_PHYS_DMA
+		/* Handle data movement if physical dma is not
+		 * enabled/supportedon host controller */
+		hpsb_register_addrspace(&sbp2_highlevel, ud->ne->host, &sbp2_physdma_ops,
+					0x0ULL, 0xfffffffcULL);
+#endif
+	}
+
+	scsi_id->hi = hi;
+
+	list_add_tail(&scsi_id->scsi_list, &hi->scsi_ids);
+
+	/* Register our host with the SCSI stack. */
+	scsi_host = scsi_host_alloc(&scsi_driver_template, 0);
+	if (!scsi_host) {
+		SBP2_ERR("failed to register scsi host");
+		goto failed_alloc;
+	}
+
+	scsi_host->hostdata[0] = (unsigned long)scsi_id;
+
+	if (!scsi_add_host(scsi_host, &ud->device)) {
+		scsi_id->scsi_host = scsi_host;
+		return scsi_id;
+	}
+
+	SBP2_ERR("failed to add scsi host");
+	scsi_host_put(scsi_host);
+
+failed_alloc:
+	sbp2_remove_device(scsi_id);
+	return NULL;
+}
+
+
+static void sbp2_host_reset(struct hpsb_host *host)
+{
+	struct sbp2scsi_host_info *hi;
+	struct scsi_id_instance_data *scsi_id;
+
+	hi = hpsb_get_hostinfo(&sbp2_highlevel, host);
+
+	if (hi) {
+		list_for_each_entry(scsi_id, &hi->scsi_ids, scsi_list)
+			scsi_block_requests(scsi_id->scsi_host);
+	}
+}
+
+
+/*
+ * This function is where we first pull the node unique ids, and then
+ * allocate memory and register a SBP-2 device.
+ */
+static int sbp2_start_device(struct scsi_id_instance_data *scsi_id)
+{
+	struct sbp2scsi_host_info *hi = scsi_id->hi;
+	struct scsi_device *sdev;
+
+	SBP2_DEBUG("sbp2_start_device");
+
+	/* Login FIFO DMA */
+	scsi_id->login_response =
+		pci_alloc_consistent(hi->host->pdev, sizeof(struct sbp2_login_response),
+				     &scsi_id->login_response_dma);
+	if (!scsi_id->login_response)
+		goto alloc_fail;
+	SBP2_DMA_ALLOC("consistent DMA region for login FIFO");
+
+	/* Query logins ORB DMA */
+	scsi_id->query_logins_orb =
+		pci_alloc_consistent(hi->host->pdev, sizeof(struct sbp2_query_logins_orb),
+				     &scsi_id->query_logins_orb_dma);
+	if (!scsi_id->query_logins_orb)
+		goto alloc_fail;
+	SBP2_DMA_ALLOC("consistent DMA region for query logins ORB");
+
+	/* Query logins response DMA */
+	scsi_id->query_logins_response =
+		pci_alloc_consistent(hi->host->pdev, sizeof(struct sbp2_query_logins_response),
+				     &scsi_id->query_logins_response_dma);
+	if (!scsi_id->query_logins_response)
+		goto alloc_fail;
+	SBP2_DMA_ALLOC("consistent DMA region for query logins response");
+
+	/* Reconnect ORB DMA */
+	scsi_id->reconnect_orb =
+		pci_alloc_consistent(hi->host->pdev, sizeof(struct sbp2_reconnect_orb),
+				     &scsi_id->reconnect_orb_dma);
+	if (!scsi_id->reconnect_orb)
+		goto alloc_fail;
+	SBP2_DMA_ALLOC("consistent DMA region for reconnect ORB");
+
+	/* Logout ORB DMA */
+	scsi_id->logout_orb =
+		pci_alloc_consistent(hi->host->pdev, sizeof(struct sbp2_logout_orb),
+				     &scsi_id->logout_orb_dma);
+	if (!scsi_id->logout_orb)
+		goto alloc_fail;
+	SBP2_DMA_ALLOC("consistent DMA region for logout ORB");
+
+	/* Login ORB DMA */
+	scsi_id->login_orb =
+		pci_alloc_consistent(hi->host->pdev, sizeof(struct sbp2_login_orb),
+				     &scsi_id->login_orb_dma);
+	if (!scsi_id->login_orb) {
+alloc_fail:
+		if (scsi_id->query_logins_response) {
+			pci_free_consistent(hi->host->pdev,
+					    sizeof(struct sbp2_query_logins_response),
+					    scsi_id->query_logins_response,
+					    scsi_id->query_logins_response_dma);
+			SBP2_DMA_FREE("query logins response DMA");
+		}
+
+		if (scsi_id->query_logins_orb) {
+			pci_free_consistent(hi->host->pdev,
+					    sizeof(struct sbp2_query_logins_orb),
+					    scsi_id->query_logins_orb,
+					    scsi_id->query_logins_orb_dma);
+			SBP2_DMA_FREE("query logins ORB DMA");
+		}
+
+		if (scsi_id->logout_orb) {
+			pci_free_consistent(hi->host->pdev,
+					sizeof(struct sbp2_logout_orb),
+					scsi_id->logout_orb,
+					scsi_id->logout_orb_dma);
+			SBP2_DMA_FREE("logout ORB DMA");
+		}
+
+		if (scsi_id->reconnect_orb) {
+			pci_free_consistent(hi->host->pdev,
+					sizeof(struct sbp2_reconnect_orb),
+					scsi_id->reconnect_orb,
+					scsi_id->reconnect_orb_dma);
+			SBP2_DMA_FREE("reconnect ORB DMA");
+		}
+
+		if (scsi_id->login_response) {
+			pci_free_consistent(hi->host->pdev,
+					sizeof(struct sbp2_login_response),
+					scsi_id->login_response,
+					scsi_id->login_response_dma);
+			SBP2_DMA_FREE("login FIFO DMA");
+		}
+
+		list_del(&scsi_id->scsi_list);
+
+		kfree(scsi_id);
+
+		SBP2_ERR ("Could not allocate memory for scsi_id");
+
+		return -ENOMEM;
+	}
+	SBP2_DMA_ALLOC("consistent DMA region for login ORB");
+
+	SBP2_DEBUG("New SBP-2 device inserted, SCSI ID = %x", scsi_id->ud->id);
+
+	/*
+	 * Create our command orb pool
+	 */
+	if (sbp2util_create_command_orb_pool(scsi_id)) {
+		SBP2_ERR("sbp2util_create_command_orb_pool failed!");
+		sbp2_remove_device(scsi_id);
+		return -ENOMEM;
+	}
+
+	/* Schedule a timeout here. The reason is that we may be so close
+	 * to a bus reset, that the device is not available for logins.
+	 * This can happen when the bus reset is caused by the host
+	 * connected to the sbp2 device being removed. That host would
+	 * have a certain amount of time to relogin before the sbp2 device
+	 * allows someone else to login instead. One second makes sense. */
+	msleep_interruptible(1000);
+	if (signal_pending(current)) {
+		SBP2_WARN("aborting sbp2_start_device due to event");
+		sbp2_remove_device(scsi_id);
+		return -EINTR;
+	}
+	
+	/*
+	 * Login to the sbp-2 device
+	 */
+	if (sbp2_login_device(scsi_id)) {
+		/* Login failed, just remove the device. */
+		sbp2_remove_device(scsi_id);
+		return -EBUSY;
+	}
+
+	/*
+	 * Set max retries to something large on the device
+	 */
+	sbp2_set_busy_timeout(scsi_id);
+
+	/*
+	 * Do a SBP-2 fetch agent reset
+	 */
+	sbp2_agent_reset(scsi_id, 1);
+
+	/*
+	 * Get the max speed and packet size that we can use
+	 */
+	sbp2_max_speed_and_size(scsi_id);
+
+	/* Add this device to the scsi layer now */
+	sdev = scsi_add_device(scsi_id->scsi_host, 0, scsi_id->ud->id, 0);
+	if (IS_ERR(sdev)) {
+		SBP2_ERR("scsi_add_device failed");
+		return PTR_ERR(sdev);
+	}
+
+	return 0;
+}
+
+/*
+ * This function removes an sbp2 device from the sbp2scsi_host_info struct.
+ */
+static void sbp2_remove_device(struct scsi_id_instance_data *scsi_id)
+{
+	struct sbp2scsi_host_info *hi;
+
+	SBP2_DEBUG("sbp2_remove_device");
+
+	if (!scsi_id)
+		return;
+
+	hi = scsi_id->hi;
+
+	/* This will remove our scsi device aswell */
+	if (scsi_id->scsi_host) {
+		scsi_remove_host(scsi_id->scsi_host);
+		scsi_host_put(scsi_id->scsi_host);
+	}
+
+	sbp2util_remove_command_orb_pool(scsi_id);
+
+	list_del(&scsi_id->scsi_list);
+
+	if (scsi_id->login_response) {
+		pci_free_consistent(hi->host->pdev,
+				    sizeof(struct sbp2_login_response),
+				    scsi_id->login_response,
+				    scsi_id->login_response_dma);
+		SBP2_DMA_FREE("single login FIFO");
+	}
+
+	if (scsi_id->login_orb) {
+		pci_free_consistent(hi->host->pdev,
+				    sizeof(struct sbp2_login_orb),
+				    scsi_id->login_orb,
+				    scsi_id->login_orb_dma);
+		SBP2_DMA_FREE("single login ORB");
+	}
+
+	if (scsi_id->reconnect_orb) {
+		pci_free_consistent(hi->host->pdev,
+				    sizeof(struct sbp2_reconnect_orb),
+				    scsi_id->reconnect_orb,
+				    scsi_id->reconnect_orb_dma);
+		SBP2_DMA_FREE("single reconnect orb");
+	}
+
+	if (scsi_id->logout_orb) {
+		pci_free_consistent(hi->host->pdev,
+				    sizeof(struct sbp2_logout_orb),
+				    scsi_id->logout_orb,
+				    scsi_id->logout_orb_dma);
+		SBP2_DMA_FREE("single logout orb");
+	}
+
+	if (scsi_id->query_logins_orb) {
+		pci_free_consistent(hi->host->pdev,
+				    sizeof(struct sbp2_query_logins_orb),
+				    scsi_id->query_logins_orb,
+				    scsi_id->query_logins_orb_dma);
+		SBP2_DMA_FREE("single query logins orb");
+	}
+
+	if (scsi_id->query_logins_response) {
+		pci_free_consistent(hi->host->pdev,
+				    sizeof(struct sbp2_query_logins_response),
+				    scsi_id->query_logins_response,
+				    scsi_id->query_logins_response_dma);
+		SBP2_DMA_FREE("single query logins data");
+	}
+
+	scsi_id->ud->device.driver_data = NULL;
+
+	SBP2_DEBUG("SBP-2 device removed, SCSI ID = %d", scsi_id->ud->id);
+
+	kfree(scsi_id);
+}
+
+#ifdef CONFIG_IEEE1394_SBP2_PHYS_DMA
+/*
+ * This function deals with physical dma write requests (for adapters that do not support
+ * physical dma in hardware). Mostly just here for debugging...
+ */
+static int sbp2_handle_physdma_write(struct hpsb_host *host, int nodeid, int destid, quadlet_t *data,
+                                     u64 addr, size_t length, u16 flags)
+{
+
+        /*
+         * Manually put the data in the right place.
+         */
+        memcpy(bus_to_virt((u32)addr), data, length);
+	sbp2util_packet_dump(data, length, "sbp2 phys dma write by device", (u32)addr);
+        return(RCODE_COMPLETE);
+}
+
+/*
+ * This function deals with physical dma read requests (for adapters that do not support
+ * physical dma in hardware). Mostly just here for debugging...
+ */
+static int sbp2_handle_physdma_read(struct hpsb_host *host, int nodeid, quadlet_t *data,
+                                    u64 addr, size_t length, u16 flags)
+{
+
+        /*
+         * Grab data from memory and send a read response.
+         */
+        memcpy(data, bus_to_virt((u32)addr), length);
+	sbp2util_packet_dump(data, length, "sbp2 phys dma read by device", (u32)addr);
+        return(RCODE_COMPLETE);
+}
+#endif
+
+
+/**************************************
+ * SBP-2 protocol related section
+ **************************************/
+
+/*
+ * This function determines if we should convert scsi commands for a particular sbp2 device type
+ */
+static __inline__ int sbp2_command_conversion_device_type(u8 device_type)
+{
+	return (((device_type == TYPE_DISK) ||
+		 (device_type == TYPE_SDAD) ||
+		 (device_type == TYPE_ROM)) ? 1:0);
+}
+
+/*
+ * This function queries the device for the maximum concurrent logins it
+ * supports.
+ */
+static int sbp2_query_logins(struct scsi_id_instance_data *scsi_id)
+{
+	struct sbp2scsi_host_info *hi = scsi_id->hi;
+	quadlet_t data[2];
+	int max_logins;
+	int active_logins;
+
+	SBP2_DEBUG("sbp2_query_logins");
+
+	scsi_id->query_logins_orb->reserved1 = 0x0;
+	scsi_id->query_logins_orb->reserved2 = 0x0;
+
+	scsi_id->query_logins_orb->query_response_lo = scsi_id->query_logins_response_dma;
+	scsi_id->query_logins_orb->query_response_hi = ORB_SET_NODE_ID(hi->host->node_id);
+	SBP2_DEBUG("sbp2_query_logins: query_response_hi/lo initialized");
+
+	scsi_id->query_logins_orb->lun_misc = ORB_SET_FUNCTION(SBP2_QUERY_LOGINS_REQUEST);
+	scsi_id->query_logins_orb->lun_misc |= ORB_SET_NOTIFY(1);
+	if (scsi_id->sbp2_device_type_and_lun != SBP2_DEVICE_TYPE_LUN_UNINITIALIZED) {
+		scsi_id->query_logins_orb->lun_misc |= ORB_SET_LUN(scsi_id->sbp2_device_type_and_lun);
+		SBP2_DEBUG("sbp2_query_logins: set lun to %d",
+			   ORB_SET_LUN(scsi_id->sbp2_device_type_and_lun));
+	}
+	SBP2_DEBUG("sbp2_query_logins: lun_misc initialized");
+
+	scsi_id->query_logins_orb->reserved_resp_length =
+		ORB_SET_QUERY_LOGINS_RESP_LENGTH(sizeof(struct sbp2_query_logins_response));
+	SBP2_DEBUG("sbp2_query_logins: reserved_resp_length initialized");
+
+	scsi_id->query_logins_orb->status_FIFO_lo = SBP2_STATUS_FIFO_ADDRESS_LO +
+						    SBP2_STATUS_FIFO_ENTRY_TO_OFFSET(scsi_id->ud->id);
+	scsi_id->query_logins_orb->status_FIFO_hi = (ORB_SET_NODE_ID(hi->host->node_id) |
+						     SBP2_STATUS_FIFO_ADDRESS_HI);
+	SBP2_DEBUG("sbp2_query_logins: status FIFO initialized");
+
+	sbp2util_cpu_to_be32_buffer(scsi_id->query_logins_orb, sizeof(struct sbp2_query_logins_orb));
+
+	SBP2_DEBUG("sbp2_query_logins: orb byte-swapped");
+
+	sbp2util_packet_dump(scsi_id->query_logins_orb, sizeof(struct sbp2_query_logins_orb),
+			     "sbp2 query logins orb", scsi_id->query_logins_orb_dma);
+
+	memset(scsi_id->query_logins_response, 0, sizeof(struct sbp2_query_logins_response));
+	memset(&scsi_id->status_block, 0, sizeof(struct sbp2_status_block));
+
+	SBP2_DEBUG("sbp2_query_logins: query_logins_response/status FIFO memset");
+
+	data[0] = ORB_SET_NODE_ID(hi->host->node_id);
+	data[1] = scsi_id->query_logins_orb_dma;
+	sbp2util_cpu_to_be32_buffer(data, 8);
+
+	atomic_set(&scsi_id->sbp2_login_complete, 0);
+
+	SBP2_DEBUG("sbp2_query_logins: prepared to write");
+	hpsb_node_write(scsi_id->ne, scsi_id->sbp2_management_agent_addr, data, 8);
+	SBP2_DEBUG("sbp2_query_logins: written");
+
+	if (sbp2util_down_timeout(&scsi_id->sbp2_login_complete, 2*HZ)) {
+		SBP2_INFO("Error querying logins to SBP-2 device - timed out");
+		return(-EIO);
+	}
+
+	if (scsi_id->status_block.ORB_offset_lo != scsi_id->query_logins_orb_dma) {
+		SBP2_INFO("Error querying logins to SBP-2 device - timed out");
+		return(-EIO);
+	}
+
+	if (STATUS_GET_RESP(scsi_id->status_block.ORB_offset_hi_misc) ||
+	    STATUS_GET_DEAD_BIT(scsi_id->status_block.ORB_offset_hi_misc) ||
+	    STATUS_GET_SBP_STATUS(scsi_id->status_block.ORB_offset_hi_misc)) {
+
+		SBP2_INFO("Error querying logins to SBP-2 device - timed out");
+		return(-EIO);
+	}
+
+	sbp2util_cpu_to_be32_buffer(scsi_id->query_logins_response, sizeof(struct sbp2_query_logins_response));
+
+	SBP2_DEBUG("length_max_logins = %x",
+		   (unsigned int)scsi_id->query_logins_response->length_max_logins);
+
+	SBP2_DEBUG("Query logins to SBP-2 device successful");
+
+	max_logins = RESPONSE_GET_MAX_LOGINS(scsi_id->query_logins_response->length_max_logins);
+	SBP2_DEBUG("Maximum concurrent logins supported: %d", max_logins);
+
+	active_logins = RESPONSE_GET_ACTIVE_LOGINS(scsi_id->query_logins_response->length_max_logins);
+	SBP2_DEBUG("Number of active logins: %d", active_logins);
+
+	if (active_logins >= max_logins) {
+		return(-EIO);
+	}
+
+	return 0;
+}
+
+/*
+ * This function is called in order to login to a particular SBP-2 device,
+ * after a bus reset.
+ */
+static int sbp2_login_device(struct scsi_id_instance_data *scsi_id)
+{
+	struct sbp2scsi_host_info *hi = scsi_id->hi;
+	quadlet_t data[2];
+
+	SBP2_DEBUG("sbp2_login_device");
+
+	if (!scsi_id->login_orb) {
+		SBP2_DEBUG("sbp2_login_device: login_orb not alloc'd!");
+		return(-EIO);
+	}
+
+	if (!exclusive_login) {
+		if (sbp2_query_logins(scsi_id)) {
+			SBP2_INFO("Device does not support any more concurrent logins");
+			return(-EIO);
+		}
+	}
+
+	/* Set-up login ORB, assume no password */
+	scsi_id->login_orb->password_hi = 0;
+	scsi_id->login_orb->password_lo = 0;
+	SBP2_DEBUG("sbp2_login_device: password_hi/lo initialized");
+
+	scsi_id->login_orb->login_response_lo = scsi_id->login_response_dma;
+	scsi_id->login_orb->login_response_hi = ORB_SET_NODE_ID(hi->host->node_id);
+	SBP2_DEBUG("sbp2_login_device: login_response_hi/lo initialized");
+
+	scsi_id->login_orb->lun_misc = ORB_SET_FUNCTION(SBP2_LOGIN_REQUEST);
+	scsi_id->login_orb->lun_misc |= ORB_SET_RECONNECT(0);	/* One second reconnect time */
+	scsi_id->login_orb->lun_misc |= ORB_SET_EXCLUSIVE(exclusive_login);	/* Exclusive access to device */
+	scsi_id->login_orb->lun_misc |= ORB_SET_NOTIFY(1);	/* Notify us of login complete */
+	/* Set the lun if we were able to pull it from the device's unit directory */
+	if (scsi_id->sbp2_device_type_and_lun != SBP2_DEVICE_TYPE_LUN_UNINITIALIZED) {
+		scsi_id->login_orb->lun_misc |= ORB_SET_LUN(scsi_id->sbp2_device_type_and_lun);
+		SBP2_DEBUG("sbp2_query_logins: set lun to %d",
+			   ORB_SET_LUN(scsi_id->sbp2_device_type_and_lun));
+	}
+	SBP2_DEBUG("sbp2_login_device: lun_misc initialized");
+
+	scsi_id->login_orb->passwd_resp_lengths =
+		ORB_SET_LOGIN_RESP_LENGTH(sizeof(struct sbp2_login_response));
+	SBP2_DEBUG("sbp2_login_device: passwd_resp_lengths initialized");
+
+	scsi_id->login_orb->status_FIFO_lo = SBP2_STATUS_FIFO_ADDRESS_LO +
+					     SBP2_STATUS_FIFO_ENTRY_TO_OFFSET(scsi_id->ud->id);
+	scsi_id->login_orb->status_FIFO_hi = (ORB_SET_NODE_ID(hi->host->node_id) |
+					      SBP2_STATUS_FIFO_ADDRESS_HI);
+	SBP2_DEBUG("sbp2_login_device: status FIFO initialized");
+
+	/*
+	 * Byte swap ORB if necessary
+	 */
+	sbp2util_cpu_to_be32_buffer(scsi_id->login_orb, sizeof(struct sbp2_login_orb));
+
+	SBP2_DEBUG("sbp2_login_device: orb byte-swapped");
+
+	sbp2util_packet_dump(scsi_id->login_orb, sizeof(struct sbp2_login_orb),
+			     "sbp2 login orb", scsi_id->login_orb_dma);
+
+	/*
+	 * Initialize login response and status fifo
+	 */
+	memset(scsi_id->login_response, 0, sizeof(struct sbp2_login_response));
+	memset(&scsi_id->status_block, 0, sizeof(struct sbp2_status_block));
+
+	SBP2_DEBUG("sbp2_login_device: login_response/status FIFO memset");
+
+	/*
+	 * Ok, let's write to the target's management agent register
+	 */
+	data[0] = ORB_SET_NODE_ID(hi->host->node_id);
+	data[1] = scsi_id->login_orb_dma;
+	sbp2util_cpu_to_be32_buffer(data, 8);
+
+	atomic_set(&scsi_id->sbp2_login_complete, 0);
+
+	SBP2_DEBUG("sbp2_login_device: prepared to write to %08x",
+		   (unsigned int)scsi_id->sbp2_management_agent_addr);
+	hpsb_node_write(scsi_id->ne, scsi_id->sbp2_management_agent_addr, data, 8);
+	SBP2_DEBUG("sbp2_login_device: written");
+
+	/*
+	 * Wait for login status (up to 20 seconds)...
+	 */
+	if (sbp2util_down_timeout(&scsi_id->sbp2_login_complete, 20*HZ)) {
+		SBP2_ERR("Error logging into SBP-2 device - login timed-out");
+		return(-EIO);
+	}
+
+	/*
+	 * Sanity. Make sure status returned matches login orb.
+	 */
+	if (scsi_id->status_block.ORB_offset_lo != scsi_id->login_orb_dma) {
+		SBP2_ERR("Error logging into SBP-2 device - login timed-out");
+		return(-EIO);
+	}
+
+	/*
+	 * Check status
+	 */
+	if (STATUS_GET_RESP(scsi_id->status_block.ORB_offset_hi_misc) ||
+	    STATUS_GET_DEAD_BIT(scsi_id->status_block.ORB_offset_hi_misc) ||
+	    STATUS_GET_SBP_STATUS(scsi_id->status_block.ORB_offset_hi_misc)) {
+
+		SBP2_ERR("Error logging into SBP-2 device - login failed");
+		return(-EIO);
+	}
+
+	/*
+	 * Byte swap the login response, for use when reconnecting or
+	 * logging out.
+	 */
+	sbp2util_cpu_to_be32_buffer(scsi_id->login_response, sizeof(struct sbp2_login_response));
+
+	/*
+	 * Grab our command block agent address from the login response.
+	 */
+	SBP2_DEBUG("command_block_agent_hi = %x",
+		   (unsigned int)scsi_id->login_response->command_block_agent_hi);
+	SBP2_DEBUG("command_block_agent_lo = %x",
+		   (unsigned int)scsi_id->login_response->command_block_agent_lo);
+
+	scsi_id->sbp2_command_block_agent_addr =
+		((u64)scsi_id->login_response->command_block_agent_hi) << 32;
+	scsi_id->sbp2_command_block_agent_addr |= ((u64)scsi_id->login_response->command_block_agent_lo);
+	scsi_id->sbp2_command_block_agent_addr &= 0x0000ffffffffffffULL;
+
+	SBP2_INFO("Logged into SBP-2 device");
+
+	return(0);
+
+}
+
+/*
+ * This function is called in order to logout from a particular SBP-2
+ * device, usually called during driver unload.
+ */
+static int sbp2_logout_device(struct scsi_id_instance_data *scsi_id)
+{
+	struct sbp2scsi_host_info *hi = scsi_id->hi;
+	quadlet_t data[2];
+	int error;
+
+	SBP2_DEBUG("sbp2_logout_device");
+
+	/*
+	 * Set-up logout ORB
+	 */
+	scsi_id->logout_orb->reserved1 = 0x0;
+	scsi_id->logout_orb->reserved2 = 0x0;
+	scsi_id->logout_orb->reserved3 = 0x0;
+	scsi_id->logout_orb->reserved4 = 0x0;
+
+	scsi_id->logout_orb->login_ID_misc = ORB_SET_FUNCTION(SBP2_LOGOUT_REQUEST);
+	scsi_id->logout_orb->login_ID_misc |= ORB_SET_LOGIN_ID(scsi_id->login_response->length_login_ID);
+
+	/* Notify us when complete */
+	scsi_id->logout_orb->login_ID_misc |= ORB_SET_NOTIFY(1);
+
+	scsi_id->logout_orb->reserved5 = 0x0;
+	scsi_id->logout_orb->status_FIFO_lo = SBP2_STATUS_FIFO_ADDRESS_LO +
+					      SBP2_STATUS_FIFO_ENTRY_TO_OFFSET(scsi_id->ud->id);
+	scsi_id->logout_orb->status_FIFO_hi = (ORB_SET_NODE_ID(hi->host->node_id) |
+					       SBP2_STATUS_FIFO_ADDRESS_HI);
+
+	/*
+	 * Byte swap ORB if necessary
+	 */
+	sbp2util_cpu_to_be32_buffer(scsi_id->logout_orb, sizeof(struct sbp2_logout_orb));
+
+	sbp2util_packet_dump(scsi_id->logout_orb, sizeof(struct sbp2_logout_orb),
+			     "sbp2 logout orb", scsi_id->logout_orb_dma);
+
+	/*
+	 * Ok, let's write to the target's management agent register
+	 */
+	data[0] = ORB_SET_NODE_ID(hi->host->node_id);
+	data[1] = scsi_id->logout_orb_dma;
+	sbp2util_cpu_to_be32_buffer(data, 8);
+
+	atomic_set(&scsi_id->sbp2_login_complete, 0);
+
+	error = hpsb_node_write(scsi_id->ne,
+	                            scsi_id->sbp2_management_agent_addr,
+	                            data, 8);
+	if (error)
+		return error;
+
+	/* Wait for device to logout...1 second. */
+	if (sbp2util_down_timeout(&scsi_id->sbp2_login_complete, HZ))
+		return -EIO;
+
+	SBP2_INFO("Logged out of SBP-2 device");
+
+	return(0);
+
+}
+
+/*
+ * This function is called in order to reconnect to a particular SBP-2
+ * device, after a bus reset.
+ */
+static int sbp2_reconnect_device(struct scsi_id_instance_data *scsi_id)
+{
+	struct sbp2scsi_host_info *hi = scsi_id->hi;
+	quadlet_t data[2];
+	int error;
+
+	SBP2_DEBUG("sbp2_reconnect_device");
+
+	/*
+	 * Set-up reconnect ORB
+	 */
+	scsi_id->reconnect_orb->reserved1 = 0x0;
+	scsi_id->reconnect_orb->reserved2 = 0x0;
+	scsi_id->reconnect_orb->reserved3 = 0x0;
+	scsi_id->reconnect_orb->reserved4 = 0x0;
+
+	scsi_id->reconnect_orb->login_ID_misc = ORB_SET_FUNCTION(SBP2_RECONNECT_REQUEST);
+	scsi_id->reconnect_orb->login_ID_misc |=
+		ORB_SET_LOGIN_ID(scsi_id->login_response->length_login_ID);
+
+	/* Notify us when complete */
+	scsi_id->reconnect_orb->login_ID_misc |= ORB_SET_NOTIFY(1);
+
+	scsi_id->reconnect_orb->reserved5 = 0x0;
+	scsi_id->reconnect_orb->status_FIFO_lo = SBP2_STATUS_FIFO_ADDRESS_LO +
+						 SBP2_STATUS_FIFO_ENTRY_TO_OFFSET(scsi_id->ud->id);
+	scsi_id->reconnect_orb->status_FIFO_hi =
+		(ORB_SET_NODE_ID(hi->host->node_id) | SBP2_STATUS_FIFO_ADDRESS_HI);
+
+	/*
+	 * Byte swap ORB if necessary
+	 */
+	sbp2util_cpu_to_be32_buffer(scsi_id->reconnect_orb, sizeof(struct sbp2_reconnect_orb));
+
+	sbp2util_packet_dump(scsi_id->reconnect_orb, sizeof(struct sbp2_reconnect_orb),
+			     "sbp2 reconnect orb", scsi_id->reconnect_orb_dma);
+
+	/*
+	 * Initialize status fifo
+	 */
+	memset(&scsi_id->status_block, 0, sizeof(struct sbp2_status_block));
+
+	/*
+	 * Ok, let's write to the target's management agent register
+	 */
+	data[0] = ORB_SET_NODE_ID(hi->host->node_id);
+	data[1] = scsi_id->reconnect_orb_dma;
+	sbp2util_cpu_to_be32_buffer(data, 8);
+
+	atomic_set(&scsi_id->sbp2_login_complete, 0);
+
+	error = hpsb_node_write(scsi_id->ne,
+	                            scsi_id->sbp2_management_agent_addr,
+	                            data, 8);
+	if (error)
+		return error;
+
+	/*
+	 * Wait for reconnect status (up to 1 second)...
+	 */
+	if (sbp2util_down_timeout(&scsi_id->sbp2_login_complete, HZ)) {
+		SBP2_ERR("Error reconnecting to SBP-2 device - reconnect timed-out");
+		return(-EIO);
+	}
+
+	/*
+	 * Sanity. Make sure status returned matches reconnect orb.
+	 */
+	if (scsi_id->status_block.ORB_offset_lo != scsi_id->reconnect_orb_dma) {
+		SBP2_ERR("Error reconnecting to SBP-2 device - reconnect timed-out");
+		return(-EIO);
+	}
+
+	/*
+	 * Check status
+	 */
+	if (STATUS_GET_RESP(scsi_id->status_block.ORB_offset_hi_misc) ||
+	    STATUS_GET_DEAD_BIT(scsi_id->status_block.ORB_offset_hi_misc) ||
+	    STATUS_GET_SBP_STATUS(scsi_id->status_block.ORB_offset_hi_misc)) {
+
+		SBP2_ERR("Error reconnecting to SBP-2 device - reconnect failed");
+		return(-EIO);
+	}
+
+	HPSB_DEBUG("Reconnected to SBP-2 device");
+
+	return(0);
+
+}
+
+/*
+ * This function is called in order to set the busy timeout (number of
+ * retries to attempt) on the sbp2 device.
+ */
+static int sbp2_set_busy_timeout(struct scsi_id_instance_data *scsi_id)
+{
+	quadlet_t data;
+
+	SBP2_DEBUG("sbp2_set_busy_timeout");
+
+	/*
+	 * Ok, let's write to the target's busy timeout register
+	 */
+	data = cpu_to_be32(SBP2_BUSY_TIMEOUT_VALUE);
+
+	if (hpsb_node_write(scsi_id->ne, SBP2_BUSY_TIMEOUT_ADDRESS, &data, 4)) {
+		SBP2_ERR("sbp2_set_busy_timeout error");
+	}
+
+	return(0);
+}
+
+
+/*
+ * This function is called to parse sbp2 device's config rom unit
+ * directory. Used to determine things like sbp2 management agent offset,
+ * and command set used (SCSI or RBC).
+ */
+static void sbp2_parse_unit_directory(struct scsi_id_instance_data *scsi_id,
+				      struct unit_directory *ud)
+{
+	struct csr1212_keyval *kv;
+	struct csr1212_dentry *dentry;
+	u64 management_agent_addr;
+	u32 command_set_spec_id, command_set, unit_characteristics,
+		firmware_revision, workarounds;
+	int i;
+
+	SBP2_DEBUG("sbp2_parse_unit_directory");
+
+	management_agent_addr = 0x0;
+	command_set_spec_id = 0x0;
+	command_set = 0x0;
+	unit_characteristics = 0x0;
+	firmware_revision = 0x0;
+
+	/* Handle different fields in the unit directory, based on keys */
+	csr1212_for_each_dir_entry(ud->ne->csr, kv, ud->ud_kv, dentry) {
+		switch (kv->key.id) {
+		case CSR1212_KV_ID_DEPENDENT_INFO:
+			if (kv->key.type == CSR1212_KV_TYPE_CSR_OFFSET) {
+				/* Save off the management agent address */
+				management_agent_addr =
+					CSR1212_REGISTER_SPACE_BASE +
+					(kv->value.csr_offset << 2);
+
+				SBP2_DEBUG("sbp2_management_agent_addr = %x",
+					   (unsigned int) management_agent_addr);
+			} else if (kv->key.type == CSR1212_KV_TYPE_IMMEDIATE) {
+				scsi_id->sbp2_device_type_and_lun = kv->value.immediate;
+			}
+			break;
+
+		case SBP2_COMMAND_SET_SPEC_ID_KEY:
+			/* Command spec organization */
+			command_set_spec_id = kv->value.immediate;
+			SBP2_DEBUG("sbp2_command_set_spec_id = %x",
+				   (unsigned int) command_set_spec_id);
+			break;
+
+		case SBP2_COMMAND_SET_KEY:
+			/* Command set used by sbp2 device */
+			command_set = kv->value.immediate;
+			SBP2_DEBUG("sbp2_command_set = %x",
+				   (unsigned int) command_set);
+			break;
+
+		case SBP2_UNIT_CHARACTERISTICS_KEY:
+			/*
+			 * Unit characterisitcs (orb related stuff
+			 * that I'm not yet paying attention to)
+			 */
+			unit_characteristics = kv->value.immediate;
+			SBP2_DEBUG("sbp2_unit_characteristics = %x",
+				   (unsigned int) unit_characteristics);
+			break;
+
+		case SBP2_FIRMWARE_REVISION_KEY:
+			/* Firmware revision */
+			firmware_revision = kv->value.immediate;
+			if (force_inquiry_hack)
+				SBP2_INFO("sbp2_firmware_revision = %x",
+				   (unsigned int) firmware_revision);
+			else	SBP2_DEBUG("sbp2_firmware_revision = %x",
+				   (unsigned int) firmware_revision);
+			break;
+
+		default:
+			break;
+		}
+	}
+
+	/* This is the start of our broken device checking. We try to hack
+	 * around oddities and known defects.  */
+	workarounds = 0x0;
+
+	/* If the vendor id is 0xa0b8 (Symbios vendor id), then we have a
+	 * bridge with 128KB max transfer size limitation. For sanity, we
+	 * only voice this when the current max_sectors setting
+	 * exceeds the 128k limit. By default, that is not the case.
+	 *
+	 * It would be really nice if we could detect this before the scsi
+	 * host gets initialized. That way we can down-force the
+	 * max_sectors to account for it. That is not currently
+	 * possible.  */
+	if ((firmware_revision & 0xffff00) ==
+			SBP2_128KB_BROKEN_FIRMWARE &&
+			(max_sectors * 512) > (128*1024)) {
+		SBP2_WARN("Node " NODE_BUS_FMT ": Bridge only supports 128KB max transfer size.",
+				NODE_BUS_ARGS(ud->ne->host, ud->ne->nodeid));
+		SBP2_WARN("WARNING: Current max_sectors setting is larger than 128KB (%d sectors)!",
+				max_sectors);
+		workarounds |= SBP2_BREAKAGE_128K_MAX_TRANSFER;
+	}
+
+	/* Check for a blacklisted set of devices that require us to force
+	 * a 36 byte host inquiry. This can be overriden as a module param
+	 * (to force all hosts).  */
+	for (i = 0; i < NUM_BROKEN_INQUIRY_DEVS; i++) {
+		if ((firmware_revision & 0xffff00) ==
+				sbp2_broken_inquiry_list[i]) {
+			SBP2_WARN("Node " NODE_BUS_FMT ": Using 36byte inquiry workaround",
+					NODE_BUS_ARGS(ud->ne->host, ud->ne->nodeid));
+			workarounds |= SBP2_BREAKAGE_INQUIRY_HACK;
+			break; /* No need to continue. */
+		}
+	}
+
+	/* If this is a logical unit directory entry, process the parent
+	 * to get the values. */
+	if (ud->flags & UNIT_DIRECTORY_LUN_DIRECTORY) {
+		struct unit_directory *parent_ud =
+			container_of(ud->device.parent, struct unit_directory, device);
+		sbp2_parse_unit_directory(scsi_id, parent_ud);
+	} else {
+		scsi_id->sbp2_management_agent_addr = management_agent_addr;
+		scsi_id->sbp2_command_set_spec_id = command_set_spec_id;
+		scsi_id->sbp2_command_set = command_set;
+		scsi_id->sbp2_unit_characteristics = unit_characteristics;
+		scsi_id->sbp2_firmware_revision = firmware_revision;
+		scsi_id->workarounds = workarounds;
+		if (ud->flags & UNIT_DIRECTORY_HAS_LUN)
+			scsi_id->sbp2_device_type_and_lun = ud->lun;
+	}
+}
+
+/*
+ * This function is called in order to determine the max speed and packet
+ * size we can use in our ORBs. Note, that we (the driver and host) only
+ * initiate the transaction. The SBP-2 device actually transfers the data
+ * (by reading from the DMA area we tell it). This means that the SBP-2
+ * device decides the actual maximum data it can transfer. We just tell it
+ * the speed that it needs to use, and the max_rec the host supports, and
+ * it takes care of the rest.
+ */
+static int sbp2_max_speed_and_size(struct scsi_id_instance_data *scsi_id)
+{
+	struct sbp2scsi_host_info *hi = scsi_id->hi;
+
+	SBP2_DEBUG("sbp2_max_speed_and_size");
+
+	/* Initial setting comes from the hosts speed map */
+	scsi_id->speed_code = hi->host->speed_map[NODEID_TO_NODE(hi->host->node_id) * 64
+						  + NODEID_TO_NODE(scsi_id->ne->nodeid)];
+
+	/* Bump down our speed if the user requested it */
+	if (scsi_id->speed_code > max_speed) {
+		scsi_id->speed_code = max_speed;
+		SBP2_ERR("Forcing SBP-2 max speed down to %s",
+			 hpsb_speedto_str[scsi_id->speed_code]);
+	}
+
+	/* Payload size is the lesser of what our speed supports and what
+	 * our host supports.  */
+	scsi_id->max_payload_size = min(sbp2_speedto_max_payload[scsi_id->speed_code],
+					(u8)(hi->host->csr.max_rec - 1));
+
+	HPSB_DEBUG("Node " NODE_BUS_FMT ": Max speed [%s] - Max payload [%u]",
+		   NODE_BUS_ARGS(hi->host, scsi_id->ne->nodeid),
+		   hpsb_speedto_str[scsi_id->speed_code],
+		   1 << ((u32)scsi_id->max_payload_size + 2));
+
+	return(0);
+}
+
+/*
+ * This function is called in order to perform a SBP-2 agent reset.
+ */
+static int sbp2_agent_reset(struct scsi_id_instance_data *scsi_id, int wait)
+{
+	quadlet_t data;
+	u64 addr;
+	int retval;
+
+	SBP2_DEBUG("sbp2_agent_reset");
+
+	/*
+	 * Ok, let's write to the target's management agent register
+	 */
+	data = ntohl(SBP2_AGENT_RESET_DATA);
+	addr = scsi_id->sbp2_command_block_agent_addr + SBP2_AGENT_RESET_OFFSET;
+
+	if (wait)
+		retval = hpsb_node_write(scsi_id->ne, addr, &data, 4);
+	else
+		retval = sbp2util_node_write_no_wait(scsi_id->ne, addr, &data, 4);
+
+	if (retval < 0) {
+		SBP2_ERR("hpsb_node_write failed.\n");
+		return -EIO;
+	}
+
+	/*
+	 * Need to make sure orb pointer is written on next command
+	 */
+	scsi_id->last_orb = NULL;
+
+	return(0);
+}
+
+/*
+ * This function is called to create the actual command orb and s/g list
+ * out of the scsi command itself.
+ */
+static int sbp2_create_command_orb(struct scsi_id_instance_data *scsi_id,
+				   struct sbp2_command_info *command,
+				   unchar *scsi_cmd,
+				   unsigned int scsi_use_sg,
+				   unsigned int scsi_request_bufflen,
+				   void *scsi_request_buffer,
+				   enum dma_data_direction dma_dir)
+
+{
+	struct sbp2scsi_host_info *hi = scsi_id->hi;
+	struct scatterlist *sgpnt = (struct scatterlist *) scsi_request_buffer;
+	struct sbp2_command_orb *command_orb = &command->command_orb;
+	struct sbp2_unrestricted_page_table *scatter_gather_element =
+		&command->scatter_gather_element[0];
+	u32 sg_count, sg_len, orb_direction;
+	dma_addr_t sg_addr;
+	int i;
+
+	/*
+	 * Set-up our command ORB..
+	 *
+	 * NOTE: We're doing unrestricted page tables (s/g), as this is
+	 * best performance (at least with the devices I have). This means
+	 * that data_size becomes the number of s/g elements, and
+	 * page_size should be zero (for unrestricted).
+	 */
+	command_orb->next_ORB_hi = ORB_SET_NULL_PTR(1);
+	command_orb->next_ORB_lo = 0x0;
+	command_orb->misc = ORB_SET_MAX_PAYLOAD(scsi_id->max_payload_size);
+	command_orb->misc |= ORB_SET_SPEED(scsi_id->speed_code);
+	command_orb->misc |= ORB_SET_NOTIFY(1);		/* Notify us when complete */
+
+	/*
+	 * Get the direction of the transfer. If the direction is unknown, then use our
+	 * goofy table as a back-up.
+	 */
+	switch (dma_dir) {
+		case DMA_NONE:
+			orb_direction = ORB_DIRECTION_NO_DATA_TRANSFER;
+			break;
+		case DMA_TO_DEVICE:
+			orb_direction = ORB_DIRECTION_WRITE_TO_MEDIA;
+			break;
+		case DMA_FROM_DEVICE:
+			orb_direction = ORB_DIRECTION_READ_FROM_MEDIA;
+			break;
+		case DMA_BIDIRECTIONAL:
+		default:
+			SBP2_ERR("SCSI data transfer direction not specified. "
+				 "Update the SBP2 direction table in sbp2.h if "
+				 "necessary for your application");
+			__scsi_print_command(scsi_cmd);
+			orb_direction = sbp2scsi_direction_table[*scsi_cmd];
+			break;
+	}
+
+	/*
+	 * Set-up our pagetable stuff... unfortunately, this has become
+	 * messier than I'd like. Need to clean this up a bit.   ;-)
+	 */
+	if (orb_direction == ORB_DIRECTION_NO_DATA_TRANSFER) {
+
+		SBP2_DEBUG("No data transfer");
+
+		/*
+		 * Handle no data transfer
+		 */
+		command_orb->data_descriptor_hi = 0x0;
+		command_orb->data_descriptor_lo = 0x0;
+		command_orb->misc |= ORB_SET_DIRECTION(1);
+
+	} else if (scsi_use_sg) {
+
+		SBP2_DEBUG("Use scatter/gather");
+
+		/*
+		 * Special case if only one element (and less than 64KB in size)
+		 */
+		if ((scsi_use_sg == 1) && (sgpnt[0].length <= SBP2_MAX_SG_ELEMENT_LENGTH)) {
+
+			SBP2_DEBUG("Only one s/g element");
+			command->dma_dir = dma_dir;
+			command->dma_size = sgpnt[0].length;
+			command->dma_type = CMD_DMA_PAGE;
+			command->cmd_dma = pci_map_page(hi->host->pdev,
+							sgpnt[0].page,
+							sgpnt[0].offset,
+							command->dma_size,
+							command->dma_dir);
+			SBP2_DMA_ALLOC("single page scatter element");
+
+			command_orb->data_descriptor_hi = ORB_SET_NODE_ID(hi->host->node_id);
+			command_orb->data_descriptor_lo = command->cmd_dma;
+			command_orb->misc |= ORB_SET_DATA_SIZE(command->dma_size);
+			command_orb->misc |= ORB_SET_DIRECTION(orb_direction);
+
+		} else {
+			int count = pci_map_sg(hi->host->pdev, sgpnt, scsi_use_sg, dma_dir);
+			SBP2_DMA_ALLOC("scatter list");
+
+			command->dma_size = scsi_use_sg;
+			command->dma_dir = dma_dir;
+			command->sge_buffer = sgpnt;
+
+			/* use page tables (s/g) */
+			command_orb->misc |= ORB_SET_PAGE_TABLE_PRESENT(0x1);
+			command_orb->misc |= ORB_SET_DIRECTION(orb_direction);
+			command_orb->data_descriptor_hi = ORB_SET_NODE_ID(hi->host->node_id);
+			command_orb->data_descriptor_lo = command->sge_dma;
+
+			/*
+			 * Loop through and fill out our sbp-2 page tables
+			 * (and split up anything too large)
+			 */
+			for (i = 0, sg_count = 0 ; i < count; i++, sgpnt++) {
+				sg_len = sg_dma_len(sgpnt);
+				sg_addr = sg_dma_address(sgpnt);
+				while (sg_len) {
+					scatter_gather_element[sg_count].segment_base_lo = sg_addr;
+					if (sg_len > SBP2_MAX_SG_ELEMENT_LENGTH) {
+						scatter_gather_element[sg_count].length_segment_base_hi =
+							PAGE_TABLE_SET_SEGMENT_LENGTH(SBP2_MAX_SG_ELEMENT_LENGTH);
+						sg_addr += SBP2_MAX_SG_ELEMENT_LENGTH;
+						sg_len -= SBP2_MAX_SG_ELEMENT_LENGTH;
+					} else {
+						scatter_gather_element[sg_count].length_segment_base_hi =
+							PAGE_TABLE_SET_SEGMENT_LENGTH(sg_len);
+						sg_len = 0;
+					}
+					sg_count++;
+				}
+			}
+
+			/* Number of page table (s/g) elements */
+			command_orb->misc |= ORB_SET_DATA_SIZE(sg_count);
+
+			sbp2util_packet_dump(scatter_gather_element,
+					     (sizeof(struct sbp2_unrestricted_page_table)) * sg_count,
+					     "sbp2 s/g list", command->sge_dma);
+
+			/*
+			 * Byte swap page tables if necessary
+			 */
+			sbp2util_cpu_to_be32_buffer(scatter_gather_element,
+						    (sizeof(struct sbp2_unrestricted_page_table)) *
+						    sg_count);
+
+		}
+
+	} else {
+
+		SBP2_DEBUG("No scatter/gather");
+
+		command->dma_dir = dma_dir;
+		command->dma_size = scsi_request_bufflen;
+		command->dma_type = CMD_DMA_SINGLE;
+		command->cmd_dma = pci_map_single (hi->host->pdev, scsi_request_buffer,
+						   command->dma_size,
+						   command->dma_dir);
+		SBP2_DMA_ALLOC("single bulk");
+
+		/*
+		 * Handle case where we get a command w/o s/g enabled (but
+		 * check for transfers larger than 64K)
+		 */
+		if (scsi_request_bufflen <= SBP2_MAX_SG_ELEMENT_LENGTH) {
+
+			command_orb->data_descriptor_hi = ORB_SET_NODE_ID(hi->host->node_id);
+			command_orb->data_descriptor_lo = command->cmd_dma;
+			command_orb->misc |= ORB_SET_DATA_SIZE(scsi_request_bufflen);
+			command_orb->misc |= ORB_SET_DIRECTION(orb_direction);
+
+			/*
+			 * Sanity, in case our direction table is not
+			 * up-to-date
+			 */
+			if (!scsi_request_bufflen) {
+				command_orb->data_descriptor_hi = 0x0;
+				command_orb->data_descriptor_lo = 0x0;
+				command_orb->misc |= ORB_SET_DIRECTION(1);
+			}
+
+		} else {
+			/*
+			 * Need to turn this into page tables, since the
+			 * buffer is too large.
+			 */
+			command_orb->data_descriptor_hi = ORB_SET_NODE_ID(hi->host->node_id);
+			command_orb->data_descriptor_lo = command->sge_dma;
+
+			/* Use page tables (s/g) */
+			command_orb->misc |= ORB_SET_PAGE_TABLE_PRESENT(0x1);
+			command_orb->misc |= ORB_SET_DIRECTION(orb_direction);
+
+			/*
+			 * fill out our sbp-2 page tables (and split up
+			 * the large buffer)
+			 */
+			sg_count = 0;
+			sg_len = scsi_request_bufflen;
+			sg_addr = command->cmd_dma;
+			while (sg_len) {
+				scatter_gather_element[sg_count].segment_base_lo = sg_addr;
+				if (sg_len > SBP2_MAX_SG_ELEMENT_LENGTH) {
+					scatter_gather_element[sg_count].length_segment_base_hi =
+						PAGE_TABLE_SET_SEGMENT_LENGTH(SBP2_MAX_SG_ELEMENT_LENGTH);
+					sg_addr += SBP2_MAX_SG_ELEMENT_LENGTH;
+					sg_len -= SBP2_MAX_SG_ELEMENT_LENGTH;
+				} else {
+					scatter_gather_element[sg_count].length_segment_base_hi =
+						PAGE_TABLE_SET_SEGMENT_LENGTH(sg_len);
+					sg_len = 0;
+				}
+				sg_count++;
+			}
+
+			/* Number of page table (s/g) elements */
+			command_orb->misc |= ORB_SET_DATA_SIZE(sg_count);
+
+			sbp2util_packet_dump(scatter_gather_element,
+					     (sizeof(struct sbp2_unrestricted_page_table)) * sg_count,
+					     "sbp2 s/g list", command->sge_dma);
+
+			/*
+			 * Byte swap page tables if necessary
+			 */
+			sbp2util_cpu_to_be32_buffer(scatter_gather_element,
+						    (sizeof(struct sbp2_unrestricted_page_table)) *
+						     sg_count);
+
+		}
+
+	}
+
+	/*
+	 * Byte swap command ORB if necessary
+	 */
+	sbp2util_cpu_to_be32_buffer(command_orb, sizeof(struct sbp2_command_orb));
+
+	/*
+	 * Put our scsi command in the command ORB
+	 */
+	memset(command_orb->cdb, 0, 12);
+	memcpy(command_orb->cdb, scsi_cmd, COMMAND_SIZE(*scsi_cmd));
+
+	return(0);
+}
+
+/*
+ * This function is called in order to begin a regular SBP-2 command.
+ */
+static int sbp2_link_orb_command(struct scsi_id_instance_data *scsi_id,
+				 struct sbp2_command_info *command)
+{
+	struct sbp2scsi_host_info *hi = scsi_id->hi;
+	struct sbp2_command_orb *command_orb = &command->command_orb;
+	struct node_entry *ne = scsi_id->ne;
+	u64 addr;
+
+	outstanding_orb_incr;
+	SBP2_ORB_DEBUG("sending command orb %p, total orbs = %x",
+			command_orb, global_outstanding_command_orbs);
+
+	pci_dma_sync_single_for_device(hi->host->pdev, command->command_orb_dma,
+				       sizeof(struct sbp2_command_orb),
+				       PCI_DMA_BIDIRECTIONAL);
+	pci_dma_sync_single_for_device(hi->host->pdev, command->sge_dma,
+				       sizeof(command->scatter_gather_element),
+				       PCI_DMA_BIDIRECTIONAL);
+	/*
+	 * Check to see if there are any previous orbs to use
+	 */
+	if (scsi_id->last_orb == NULL) {
+		quadlet_t data[2];
+
+		/*
+		 * Ok, let's write to the target's management agent register
+		 */
+		addr = scsi_id->sbp2_command_block_agent_addr + SBP2_ORB_POINTER_OFFSET;
+		data[0] = ORB_SET_NODE_ID(hi->host->node_id);
+		data[1] = command->command_orb_dma;
+		sbp2util_cpu_to_be32_buffer(data, 8);
+
+		SBP2_ORB_DEBUG("write command agent, command orb %p", command_orb);
+
+		if (sbp2util_node_write_no_wait(ne, addr, data, 8) < 0) {
+			SBP2_ERR("sbp2util_node_write_no_wait failed.\n");
+			return -EIO;
+		}
+
+		SBP2_ORB_DEBUG("write command agent complete");
+
+		scsi_id->last_orb = command_orb;
+		scsi_id->last_orb_dma = command->command_orb_dma;
+
+	} else {
+		quadlet_t data;
+
+		/*
+		 * We have an orb already sent (maybe or maybe not
+		 * processed) that we can append this orb to. So do so,
+		 * and ring the doorbell. Have to be very careful
+		 * modifying these next orb pointers, as they are accessed
+		 * both by the sbp2 device and us.
+		 */
+		scsi_id->last_orb->next_ORB_lo =
+			cpu_to_be32(command->command_orb_dma);
+		/* Tells hardware that this pointer is valid */
+		scsi_id->last_orb->next_ORB_hi = 0x0;
+		pci_dma_sync_single_for_device(hi->host->pdev, scsi_id->last_orb_dma,
+					       sizeof(struct sbp2_command_orb),
+					       PCI_DMA_BIDIRECTIONAL);
+
+		/*
+		 * Ring the doorbell
+		 */
+		data = cpu_to_be32(command->command_orb_dma);
+		addr = scsi_id->sbp2_command_block_agent_addr + SBP2_DOORBELL_OFFSET;
+
+		SBP2_ORB_DEBUG("ring doorbell, command orb %p", command_orb);
+
+		if (sbp2util_node_write_no_wait(ne, addr, &data, 4) < 0) {
+			SBP2_ERR("sbp2util_node_write_no_wait failed");
+			return(-EIO);
+		}
+
+		scsi_id->last_orb = command_orb;
+		scsi_id->last_orb_dma = command->command_orb_dma;
+
+	}
+       	return(0);
+}
+
+/*
+ * This function is called in order to begin a regular SBP-2 command.
+ */
+static int sbp2_send_command(struct scsi_id_instance_data *scsi_id,
+			     struct scsi_cmnd *SCpnt,
+			     void (*done)(struct scsi_cmnd *))
+{
+	unchar *cmd = (unchar *) SCpnt->cmnd;
+	unsigned int request_bufflen = SCpnt->request_bufflen;
+	struct sbp2_command_info *command;
+
+	SBP2_DEBUG("sbp2_send_command");
+#if (CONFIG_IEEE1394_SBP2_DEBUG >= 2) || defined(CONFIG_IEEE1394_SBP2_PACKET_DUMP)
+	printk("[scsi command]\n   ");
+	scsi_print_command(SCpnt);
+#endif
+	SBP2_DEBUG("SCSI transfer size = %x", request_bufflen);
+	SBP2_DEBUG("SCSI s/g elements = %x", (unsigned int)SCpnt->use_sg);
+
+	/*
+	 * Allocate a command orb and s/g structure
+	 */
+	command = sbp2util_allocate_command_orb(scsi_id, SCpnt, done);
+	if (!command) {
+		return(-EIO);
+	}
+
+	/*
+	 * The scsi stack sends down a request_bufflen which does not match the
+	 * length field in the scsi cdb. This causes some sbp2 devices to
+	 * reject this inquiry command. Fix the request_bufflen.
+	 */
+	if (*cmd == INQUIRY) {
+		if (force_inquiry_hack || scsi_id->workarounds & SBP2_BREAKAGE_INQUIRY_HACK)
+			request_bufflen = cmd[4] = 0x24;
+		else
+			request_bufflen = cmd[4];
+	}
+
+	/*
+	 * Now actually fill in the comamnd orb and sbp2 s/g list
+	 */
+	sbp2_create_command_orb(scsi_id, command, cmd, SCpnt->use_sg,
+				request_bufflen, SCpnt->request_buffer,
+				SCpnt->sc_data_direction);
+	/*
+	 * Update our cdb if necessary (to handle sbp2 RBC command set
+	 * differences). This is where the command set hacks go!   =)
+	 */
+	sbp2_check_sbp2_command(scsi_id, command->command_orb.cdb);
+
+	sbp2util_packet_dump(&command->command_orb, sizeof(struct sbp2_command_orb),
+			     "sbp2 command orb", command->command_orb_dma);
+
+	/*
+	 * Initialize status fifo
+	 */
+	memset(&scsi_id->status_block, 0, sizeof(struct sbp2_status_block));
+
+	/*
+	 * Link up the orb, and ring the doorbell if needed
+	 */
+	sbp2_link_orb_command(scsi_id, command);
+
+	return(0);
+}
+
+
+/*
+ * This function deals with command set differences between Linux scsi
+ * command set and sbp2 RBC command set.
+ */
+static void sbp2_check_sbp2_command(struct scsi_id_instance_data *scsi_id, unchar *cmd)
+{
+	unchar new_cmd[16];
+	u8 device_type = SBP2_DEVICE_TYPE (scsi_id->sbp2_device_type_and_lun);
+
+	SBP2_DEBUG("sbp2_check_sbp2_command");
+
+	switch (*cmd) {
+
+		case READ_6:
+
+			if (sbp2_command_conversion_device_type(device_type)) {
+
+				SBP2_DEBUG("Convert READ_6 to READ_10");
+
+				/*
+				 * Need to turn read_6 into read_10
+				 */
+				new_cmd[0] = 0x28;
+				new_cmd[1] = (cmd[1] & 0xe0);
+				new_cmd[2] = 0x0;
+				new_cmd[3] = (cmd[1] & 0x1f);
+				new_cmd[4] = cmd[2];
+				new_cmd[5] = cmd[3];
+				new_cmd[6] = 0x0;
+				new_cmd[7] = 0x0;
+				new_cmd[8] = cmd[4];
+				new_cmd[9] = cmd[5];
+
+				memcpy(cmd, new_cmd, 10);
+
+			}
+
+			break;
+
+		case WRITE_6:
+
+			if (sbp2_command_conversion_device_type(device_type)) {
+
+				SBP2_DEBUG("Convert WRITE_6 to WRITE_10");
+
+				/*
+				 * Need to turn write_6 into write_10
+				 */
+				new_cmd[0] = 0x2a;
+				new_cmd[1] = (cmd[1] & 0xe0);
+				new_cmd[2] = 0x0;
+				new_cmd[3] = (cmd[1] & 0x1f);
+				new_cmd[4] = cmd[2];
+				new_cmd[5] = cmd[3];
+				new_cmd[6] = 0x0;
+				new_cmd[7] = 0x0;
+				new_cmd[8] = cmd[4];
+				new_cmd[9] = cmd[5];
+
+				memcpy(cmd, new_cmd, 10);
+
+			}
+
+			break;
+
+		case MODE_SENSE:
+
+			if (sbp2_command_conversion_device_type(device_type)) {
+
+				SBP2_DEBUG("Convert MODE_SENSE_6 to MODE_SENSE_10");
+
+				/*
+				 * Need to turn mode_sense_6 into mode_sense_10
+				 */
+				new_cmd[0] = 0x5a;
+				new_cmd[1] = cmd[1];
+				new_cmd[2] = cmd[2];
+				new_cmd[3] = 0x0;
+				new_cmd[4] = 0x0;
+				new_cmd[5] = 0x0;
+				new_cmd[6] = 0x0;
+				new_cmd[7] = 0x0;
+				new_cmd[8] = cmd[4];
+				new_cmd[9] = cmd[5];
+
+				memcpy(cmd, new_cmd, 10);
+
+			}
+
+			break;
+
+		case MODE_SELECT:
+
+			/*
+			 * TODO. Probably need to change mode select to 10 byte version
+			 */
+
+		default:
+			break;
+	}
+
+	return;
+}
+
+/*
+ * Translates SBP-2 status into SCSI sense data for check conditions
+ */
+static unsigned int sbp2_status_to_sense_data(unchar *sbp2_status, unchar *sense_data)
+{
+	SBP2_DEBUG("sbp2_status_to_sense_data");
+
+	/*
+	 * Ok, it's pretty ugly...   ;-)
+	 */
+	sense_data[0] = 0x70;
+	sense_data[1] = 0x0;
+	sense_data[2] = sbp2_status[9];
+	sense_data[3] = sbp2_status[12];
+	sense_data[4] = sbp2_status[13];
+	sense_data[5] = sbp2_status[14];
+	sense_data[6] = sbp2_status[15];
+	sense_data[7] = 10;
+	sense_data[8] = sbp2_status[16];
+	sense_data[9] = sbp2_status[17];
+	sense_data[10] = sbp2_status[18];
+	sense_data[11] = sbp2_status[19];
+	sense_data[12] = sbp2_status[10];
+	sense_data[13] = sbp2_status[11];
+	sense_data[14] = sbp2_status[20];
+	sense_data[15] = sbp2_status[21];
+
+	return(sbp2_status[8] & 0x3f);	/* return scsi status */
+}
+
+/*
+ * This function is called after a command is completed, in order to do any necessary SBP-2
+ * response data translations for the SCSI stack
+ */
+static void sbp2_check_sbp2_response(struct scsi_id_instance_data *scsi_id, 
+				     struct scsi_cmnd *SCpnt)
+{
+	u8 *scsi_buf = SCpnt->request_buffer;
+	u8 device_type = SBP2_DEVICE_TYPE (scsi_id->sbp2_device_type_and_lun);
+
+	SBP2_DEBUG("sbp2_check_sbp2_response");
+
+	switch (SCpnt->cmnd[0]) {
+
+		case INQUIRY:
+
+			/*
+			 * If scsi_id->sbp2_device_type_and_lun is uninitialized, then fill 
+			 * this information in from the inquiry response data. Lun is set to zero.
+			 */
+			if (scsi_id->sbp2_device_type_and_lun == SBP2_DEVICE_TYPE_LUN_UNINITIALIZED) {
+				SBP2_DEBUG("Creating sbp2_device_type_and_lun from scsi inquiry data");
+				scsi_id->sbp2_device_type_and_lun = (scsi_buf[0] & 0x1f) << 16;
+			}
+
+			/*
+			 * Make sure data length is ok. Minimum length is 36 bytes
+			 */
+			if (scsi_buf[4] == 0) {
+				scsi_buf[4] = 36 - 5;
+			}
+
+			/*
+			 * Check for Simple Direct Access Device and change it to TYPE_DISK
+			 */
+			if ((scsi_buf[0] & 0x1f) == TYPE_SDAD) {
+				SBP2_DEBUG("Changing TYPE_SDAD to TYPE_DISK");
+				scsi_buf[0] &= 0xe0;
+			}
+
+			/*
+			 * Fix ansi revision and response data format
+			 */
+			scsi_buf[2] |= 2;
+			scsi_buf[3] = (scsi_buf[3] & 0xf0) | 2;
+
+			break;
+
+		case MODE_SENSE:
+
+			if (sbp2_command_conversion_device_type(device_type)) {
+
+				SBP2_DEBUG("Modify mode sense response (10 byte version)");
+
+				scsi_buf[0] = scsi_buf[1];	/* Mode data length */
+				scsi_buf[1] = scsi_buf[2];	/* Medium type */
+				scsi_buf[2] = scsi_buf[3];	/* Device specific parameter */
+				scsi_buf[3] = scsi_buf[7];	/* Block descriptor length */
+				memcpy(scsi_buf + 4, scsi_buf + 8, scsi_buf[0]);
+			}
+
+			break;
+
+		case MODE_SELECT:
+
+			/*
+			 * TODO. Probably need to change mode select to 10 byte version
+			 */
+
+		default:
+			break;
+	}
+	return;
+}
+
+/*
+ * This function deals with status writes from the SBP-2 device
+ */
+static int sbp2_handle_status_write(struct hpsb_host *host, int nodeid, int destid,
+				    quadlet_t *data, u64 addr, size_t length, u16 fl)
+{
+	struct sbp2scsi_host_info *hi;
+	struct scsi_id_instance_data *scsi_id = NULL, *scsi_id_tmp;
+	u32 id;
+	struct scsi_cmnd *SCpnt = NULL;
+	u32 scsi_status = SBP2_SCSI_STATUS_GOOD;
+	struct sbp2_command_info *command;
+
+	SBP2_DEBUG("sbp2_handle_status_write");
+
+	sbp2util_packet_dump(data, length, "sbp2 status write by device", (u32)addr);
+
+	if (!host) {
+		SBP2_ERR("host is NULL - this is bad!");
+		return(RCODE_ADDRESS_ERROR);
+	}
+
+	hi = hpsb_get_hostinfo(&sbp2_highlevel, host);
+
+	if (!hi) {
+		SBP2_ERR("host info is NULL - this is bad!");
+		return(RCODE_ADDRESS_ERROR);
+	}
+
+	/*
+	 * Find our scsi_id structure by looking at the status fifo address written to by
+	 * the sbp2 device.
+	 */
+	id = SBP2_STATUS_FIFO_OFFSET_TO_ENTRY((u32)(addr - SBP2_STATUS_FIFO_ADDRESS));
+	list_for_each_entry(scsi_id_tmp, &hi->scsi_ids, scsi_list) {
+		if (scsi_id_tmp->ne->nodeid == nodeid && scsi_id_tmp->ud->id == id) {
+			scsi_id = scsi_id_tmp;
+			break;
+		}
+	}
+
+	if (!scsi_id) {
+		SBP2_ERR("scsi_id is NULL - device is gone?");
+		return(RCODE_ADDRESS_ERROR);
+	}
+
+	/*
+	 * Put response into scsi_id status fifo...
+	 */
+	memcpy(&scsi_id->status_block, data, length);
+
+	/*
+	 * Byte swap first two quadlets (8 bytes) of status for processing
+	 */
+	sbp2util_be32_to_cpu_buffer(&scsi_id->status_block, 8);
+
+	/*
+	 * Handle command ORB status here if necessary. First, need to match status with command.
+	 */
+	command = sbp2util_find_command_for_orb(scsi_id, scsi_id->status_block.ORB_offset_lo);
+	if (command) {
+
+		SBP2_DEBUG("Found status for command ORB");
+		pci_dma_sync_single_for_cpu(hi->host->pdev, command->command_orb_dma,
+					    sizeof(struct sbp2_command_orb),
+					    PCI_DMA_BIDIRECTIONAL);
+		pci_dma_sync_single_for_cpu(hi->host->pdev, command->sge_dma,
+					    sizeof(command->scatter_gather_element),
+					    PCI_DMA_BIDIRECTIONAL);
+
+		SBP2_ORB_DEBUG("matched command orb %p", &command->command_orb);
+		outstanding_orb_decr;
+
+		/*
+		 * Matched status with command, now grab scsi command pointers and check status
+		 */
+		SCpnt = command->Current_SCpnt;
+		sbp2util_mark_command_completed(scsi_id, command);
+
+		if (SCpnt) {
+
+			/*
+			 * See if the target stored any scsi status information
+			 */
+			if (STATUS_GET_LENGTH(scsi_id->status_block.ORB_offset_hi_misc) > 1) {
+				/*
+				 * Translate SBP-2 status to SCSI sense data
+				 */
+				SBP2_DEBUG("CHECK CONDITION");
+				scsi_status = sbp2_status_to_sense_data((unchar *)&scsi_id->status_block, SCpnt->sense_buffer);
+			}
+
+			/*
+			 * Check to see if the dead bit is set. If so, we'll have to initiate
+			 * a fetch agent reset.
+			 */
+			if (STATUS_GET_DEAD_BIT(scsi_id->status_block.ORB_offset_hi_misc)) {
+
+				/*
+				 * Initiate a fetch agent reset.
+				 */
+				SBP2_DEBUG("Dead bit set - initiating fetch agent reset");
+                                sbp2_agent_reset(scsi_id, 0);
+			}
+
+			SBP2_ORB_DEBUG("completing command orb %p", &command->command_orb);
+		}
+
+		/*
+		 * Check here to see if there are no commands in-use. If there are none, we can
+		 * null out last orb so that next time around we write directly to the orb pointer...
+		 * Quick start saves one 1394 bus transaction.
+		 */
+		if (list_empty(&scsi_id->sbp2_command_orb_inuse)) {
+			scsi_id->last_orb = NULL;
+		}
+
+	} else {
+
+		/*
+		 * It's probably a login/logout/reconnect status.
+		 */
+		if ((scsi_id->login_orb_dma == scsi_id->status_block.ORB_offset_lo) ||
+		    (scsi_id->query_logins_orb_dma == scsi_id->status_block.ORB_offset_lo) ||
+		    (scsi_id->reconnect_orb_dma == scsi_id->status_block.ORB_offset_lo) ||
+		    (scsi_id->logout_orb_dma == scsi_id->status_block.ORB_offset_lo)) {
+			atomic_set(&scsi_id->sbp2_login_complete, 1);
+		}
+	}
+
+	if (SCpnt) {
+
+		/* Complete the SCSI command. */
+		SBP2_DEBUG("Completing SCSI command");
+		sbp2scsi_complete_command(scsi_id, scsi_status, SCpnt,
+					  command->Current_done);
+		SBP2_ORB_DEBUG("command orb completed");
+	}
+
+	return(RCODE_COMPLETE);
+}
+
+
+/**************************************
+ * SCSI interface related section
+ **************************************/
+
+/*
+ * This routine is the main request entry routine for doing I/O. It is
+ * called from the scsi stack directly.
+ */
+static int sbp2scsi_queuecommand(struct scsi_cmnd *SCpnt,
+				 void (*done)(struct scsi_cmnd *))
+{
+	struct scsi_id_instance_data *scsi_id =
+		(struct scsi_id_instance_data *)SCpnt->device->host->hostdata[0];
+	struct sbp2scsi_host_info *hi;
+
+	SBP2_DEBUG("sbp2scsi_queuecommand");
+
+	/*
+	 * If scsi_id is null, it means there is no device in this slot,
+	 * so we should return selection timeout.
+	 */
+	if (!scsi_id) {
+		SCpnt->result = DID_NO_CONNECT << 16;
+		done (SCpnt);
+		return 0;
+	}
+
+	hi = scsi_id->hi;
+
+	if (!hi) {
+		SBP2_ERR("sbp2scsi_host_info is NULL - this is bad!");
+		SCpnt->result = DID_NO_CONNECT << 16;
+		done (SCpnt);
+		return(0);
+	}
+
+	/*
+	 * Until we handle multiple luns, just return selection time-out
+	 * to any IO directed at non-zero LUNs
+	 */
+	if (SCpnt->device->lun) {
+		SCpnt->result = DID_NO_CONNECT << 16;
+		done (SCpnt);
+		return(0);
+	}
+
+	/*
+	 * Check for request sense command, and handle it here
+	 * (autorequest sense)
+	 */
+	if (SCpnt->cmnd[0] == REQUEST_SENSE) {
+		SBP2_DEBUG("REQUEST_SENSE");
+		memcpy(SCpnt->request_buffer, SCpnt->sense_buffer, SCpnt->request_bufflen);
+		memset(SCpnt->sense_buffer, 0, sizeof(SCpnt->sense_buffer));
+		sbp2scsi_complete_command(scsi_id, SBP2_SCSI_STATUS_GOOD, SCpnt, done);
+		return(0);
+	}
+
+	/*
+	 * Check to see if we are in the middle of a bus reset.
+	 */
+	if (!hpsb_node_entry_valid(scsi_id->ne)) {
+		SBP2_ERR("Bus reset in progress - rejecting command");
+		SCpnt->result = DID_BUS_BUSY << 16;
+		done (SCpnt);
+		return(0);
+	}
+
+	/*
+	 * Try and send our SCSI command
+	 */
+	if (sbp2_send_command(scsi_id, SCpnt, done)) {
+		SBP2_ERR("Error sending SCSI command");
+		sbp2scsi_complete_command(scsi_id, SBP2_SCSI_STATUS_SELECTION_TIMEOUT,
+					  SCpnt, done);
+	}
+
+	return(0);
+}
+
+/*
+ * This function is called in order to complete all outstanding SBP-2
+ * commands (in case of resets, etc.).
+ */
+static void sbp2scsi_complete_all_commands(struct scsi_id_instance_data *scsi_id,
+					   u32 status)
+{
+	struct sbp2scsi_host_info *hi = scsi_id->hi;
+	struct list_head *lh;
+	struct sbp2_command_info *command;
+
+	SBP2_DEBUG("sbp2scsi_complete_all_commands");
+
+	while (!list_empty(&scsi_id->sbp2_command_orb_inuse)) {
+		SBP2_DEBUG("Found pending command to complete");
+		lh = scsi_id->sbp2_command_orb_inuse.next;
+		command = list_entry(lh, struct sbp2_command_info, list);
+		pci_dma_sync_single_for_cpu(hi->host->pdev, command->command_orb_dma,
+					    sizeof(struct sbp2_command_orb),
+					    PCI_DMA_BIDIRECTIONAL);
+		pci_dma_sync_single_for_cpu(hi->host->pdev, command->sge_dma,
+					    sizeof(command->scatter_gather_element),
+					    PCI_DMA_BIDIRECTIONAL);
+		sbp2util_mark_command_completed(scsi_id, command);
+		if (command->Current_SCpnt) {
+			command->Current_SCpnt->result = status << 16;
+			command->Current_done(command->Current_SCpnt);
+		}
+	}
+
+	return;
+}
+
+/*
+ * This function is called in order to complete a regular SBP-2 command.
+ *
+ * This can be called in interrupt context.
+ */
+static void sbp2scsi_complete_command(struct scsi_id_instance_data *scsi_id,
+				      u32 scsi_status, struct scsi_cmnd *SCpnt,
+				      void (*done)(struct scsi_cmnd *))
+{
+	unsigned long flags;
+
+	SBP2_DEBUG("sbp2scsi_complete_command");
+
+	/*
+	 * Sanity
+	 */
+	if (!SCpnt) {
+		SBP2_ERR("SCpnt is NULL");
+		return;
+	}
+
+	/*
+	 * If a bus reset is in progress and there was an error, don't
+	 * complete the command, just let it get retried at the end of the
+	 * bus reset.
+	 */
+	if (!hpsb_node_entry_valid(scsi_id->ne) && (scsi_status != SBP2_SCSI_STATUS_GOOD)) {
+		SBP2_ERR("Bus reset in progress - retry command later");
+		return;
+	}
+ 
+	/*
+	 * Switch on scsi status
+	 */
+	switch (scsi_status) {
+		case SBP2_SCSI_STATUS_GOOD:
+			SCpnt->result = DID_OK;
+			break;
+
+		case SBP2_SCSI_STATUS_BUSY:
+			SBP2_ERR("SBP2_SCSI_STATUS_BUSY");
+			SCpnt->result = DID_BUS_BUSY << 16;
+			break;
+
+		case SBP2_SCSI_STATUS_CHECK_CONDITION:
+			SBP2_DEBUG("SBP2_SCSI_STATUS_CHECK_CONDITION");
+			SCpnt->result = CHECK_CONDITION << 1;
+
+			/*
+			 * Debug stuff
+			 */
+#if CONFIG_IEEE1394_SBP2_DEBUG >= 1
+			scsi_print_command(SCpnt);
+			scsi_print_sense("bh", SCpnt);
+#endif
+
+			break;
+
+		case SBP2_SCSI_STATUS_SELECTION_TIMEOUT:
+			SBP2_ERR("SBP2_SCSI_STATUS_SELECTION_TIMEOUT");
+			SCpnt->result = DID_NO_CONNECT << 16;
+			scsi_print_command(SCpnt);
+			break;
+
+		case SBP2_SCSI_STATUS_CONDITION_MET:
+		case SBP2_SCSI_STATUS_RESERVATION_CONFLICT:
+		case SBP2_SCSI_STATUS_COMMAND_TERMINATED:
+			SBP2_ERR("Bad SCSI status = %x", scsi_status);
+			SCpnt->result = DID_ERROR << 16;
+			scsi_print_command(SCpnt);
+			break;
+
+		default:
+			SBP2_ERR("Unsupported SCSI status = %x", scsi_status);
+			SCpnt->result = DID_ERROR << 16;
+	}
+
+	/*
+	 * Take care of any sbp2 response data mucking here (RBC stuff, etc.)
+	 */
+	if (SCpnt->result == DID_OK) {
+		sbp2_check_sbp2_response(scsi_id, SCpnt);
+	}
+
+	/*
+	 * If a bus reset is in progress and there was an error, complete
+	 * the command as busy so that it will get retried.
+	 */
+	if (!hpsb_node_entry_valid(scsi_id->ne) && (scsi_status != SBP2_SCSI_STATUS_GOOD)) {
+		SBP2_ERR("Completing command with busy (bus reset)");
+		SCpnt->result = DID_BUS_BUSY << 16;
+	}
+
+	/*
+	 * If a unit attention occurs, return busy status so it gets
+	 * retried... it could have happened because of a 1394 bus reset
+	 * or hot-plug...
+	 */
+#if 0
+	if ((scsi_status == SBP2_SCSI_STATUS_CHECK_CONDITION) &&
+	    (SCpnt->sense_buffer[2] == UNIT_ATTENTION)) {
+		SBP2_DEBUG("UNIT ATTENTION - return busy");
+		SCpnt->result = DID_BUS_BUSY << 16;
+	}
+#endif
+
+	/*
+	 * Tell scsi stack that we're done with this command
+	 */
+	spin_lock_irqsave(scsi_id->scsi_host->host_lock,flags);
+	done (SCpnt);
+	spin_unlock_irqrestore(scsi_id->scsi_host->host_lock,flags);
+
+	return;
+}
+
+
+static int sbp2scsi_slave_configure (struct scsi_device *sdev)
+{
+	blk_queue_dma_alignment(sdev->request_queue, (512 - 1));
+
+	return 0;
+}
+
+
+/*
+ * Called by scsi stack when something has really gone wrong.  Usually
+ * called when a command has timed-out for some reason.
+ */
+static int sbp2scsi_abort(struct scsi_cmnd *SCpnt)
+{
+	struct scsi_id_instance_data *scsi_id =
+		(struct scsi_id_instance_data *)SCpnt->device->host->hostdata[0];
+	struct sbp2scsi_host_info *hi = scsi_id->hi;
+	struct sbp2_command_info *command;
+
+	SBP2_ERR("aborting sbp2 command");
+	scsi_print_command(SCpnt);
+
+	if (scsi_id) {
+
+		/*
+		 * Right now, just return any matching command structures
+		 * to the free pool.
+		 */
+		command = sbp2util_find_command_for_SCpnt(scsi_id, SCpnt);
+		if (command) {
+			SBP2_DEBUG("Found command to abort");
+			pci_dma_sync_single_for_cpu(hi->host->pdev,
+						    command->command_orb_dma,
+						    sizeof(struct sbp2_command_orb),
+						    PCI_DMA_BIDIRECTIONAL);
+			pci_dma_sync_single_for_cpu(hi->host->pdev,
+						    command->sge_dma,
+						    sizeof(command->scatter_gather_element),
+						    PCI_DMA_BIDIRECTIONAL);
+			sbp2util_mark_command_completed(scsi_id, command);
+			if (command->Current_SCpnt) {
+				command->Current_SCpnt->result = DID_ABORT << 16;
+				command->Current_done(command->Current_SCpnt);
+			}
+		}
+
+		/*
+		 * Initiate a fetch agent reset.
+		 */
+		sbp2_agent_reset(scsi_id, 0);
+		sbp2scsi_complete_all_commands(scsi_id, DID_BUS_BUSY);
+	}
+
+	return(SUCCESS);
+}
+
+/*
+ * Called by scsi stack when something has really gone wrong.
+ */
+static int sbp2scsi_reset(struct scsi_cmnd *SCpnt)
+{
+	struct scsi_id_instance_data *scsi_id =
+		(struct scsi_id_instance_data *)SCpnt->device->host->hostdata[0];
+
+	SBP2_ERR("reset requested");
+
+	if (scsi_id) {
+		SBP2_ERR("Generating sbp2 fetch agent reset");
+		sbp2_agent_reset(scsi_id, 0);
+	}
+
+	return(SUCCESS);
+}
+
+static const char *sbp2scsi_info (struct Scsi_Host *host)
+{
+        return "SCSI emulation for IEEE-1394 SBP-2 Devices";
+}
+
+static ssize_t sbp2_sysfs_ieee1394_id_show(struct device *dev, char *buf)
+{
+	struct scsi_device *sdev;
+	struct scsi_id_instance_data *scsi_id;
+	int lun;
+
+	if (!(sdev = to_scsi_device(dev)))
+		return 0;
+
+	if (!(scsi_id = (struct scsi_id_instance_data *)sdev->host->hostdata[0]))
+		return 0;
+
+	if (scsi_id->sbp2_device_type_and_lun == SBP2_DEVICE_TYPE_LUN_UNINITIALIZED)
+		lun = 0;
+	else
+		lun = ORB_SET_LUN(scsi_id->sbp2_device_type_and_lun);
+
+	return sprintf(buf, "%016Lx:%d:%d\n", (unsigned long long)scsi_id->ne->guid,
+		       scsi_id->ud->id, lun);
+}
+static DEVICE_ATTR(ieee1394_id, S_IRUGO, sbp2_sysfs_ieee1394_id_show, NULL);
+
+static struct device_attribute *sbp2_sysfs_sdev_attrs[] = {
+	&dev_attr_ieee1394_id,
+	NULL
+};
+
+MODULE_AUTHOR("Ben Collins <bcollins@debian.org>");
+MODULE_DESCRIPTION("IEEE-1394 SBP-2 protocol driver");
+MODULE_SUPPORTED_DEVICE(SBP2_DEVICE_NAME);
+MODULE_LICENSE("GPL");
+
+/* SCSI host template */
+static struct scsi_host_template scsi_driver_template = {
+	.module =			THIS_MODULE,
+	.name =				"SBP-2 IEEE-1394",
+	.proc_name =			SBP2_DEVICE_NAME,
+	.info =				sbp2scsi_info,
+	.queuecommand =			sbp2scsi_queuecommand,
+	.eh_abort_handler =		sbp2scsi_abort,
+	.eh_device_reset_handler =	sbp2scsi_reset,
+	.eh_bus_reset_handler =		sbp2scsi_reset,
+	.eh_host_reset_handler =	sbp2scsi_reset,
+	.slave_configure =		sbp2scsi_slave_configure,
+	.this_id =			-1,
+	.sg_tablesize =			SG_ALL,
+	.use_clustering =		ENABLE_CLUSTERING,
+	.cmd_per_lun =			SBP2_MAX_CMDS,
+	.can_queue = 			SBP2_MAX_CMDS,
+	.emulated =			1,
+	.sdev_attrs =			sbp2_sysfs_sdev_attrs,
+};
+
+static int sbp2_module_init(void)
+{
+	int ret;
+
+	SBP2_DEBUG("sbp2_module_init");
+
+	printk(KERN_INFO "sbp2: %s\n", version);
+
+	/* Module load debug option to force one command at a time (serializing I/O) */
+	if (serialize_io) {
+		SBP2_ERR("Driver forced to serialize I/O (serialize_io = 1)");
+		scsi_driver_template.can_queue = 1;
+		scsi_driver_template.cmd_per_lun = 1;
+	}
+
+	/* Set max sectors (module load option). Default is 255 sectors. */
+	scsi_driver_template.max_sectors = max_sectors;
+
+
+	/* Register our high level driver with 1394 stack */
+	hpsb_register_highlevel(&sbp2_highlevel);
+
+	ret = hpsb_register_protocol(&sbp2_driver);
+	if (ret) {
+		SBP2_ERR("Failed to register protocol");
+		hpsb_unregister_highlevel(&sbp2_highlevel);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void __exit sbp2_module_exit(void)
+{
+	SBP2_DEBUG("sbp2_module_exit");
+
+	hpsb_unregister_protocol(&sbp2_driver);
+
+	hpsb_unregister_highlevel(&sbp2_highlevel);
+}
+
+module_init(sbp2_module_init);
+module_exit(sbp2_module_exit);